BAE Systems 81FCGX First InterComm VCA100 model 81FCGX User Manual Installation guide

Download:
Mirror Download [FCC.gov]
Document ID	1067568
Application ID	Kvfbushu68b0CEqBUH0pMA==
Document Description	Installation guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	56.79kB (709855 bits)
Date Submitted	2009-02-12 00:00:00
Date Available	2009-02-19 00:00:00
Creation Date	2008-11-03 14:17:08
Producing Software	Acrobat Distiller 7.0.5 (Windows)
Document Lastmod	2008-11-03 14:17:08
Document Title	Microsoft Word - A29799 FIC VCA100 Installation Guide Rev A Final.doc
Document Creator	PScript5.dll Version 5.2.2
Document Author:	ralph.lombardo

A29799 rev A
May 2008
First InterComm™ System
VCA100
Installation Guide
** NOTE: if time permits this manual will be laid out in 8x10 format w/
spiral binder by the Media dept and made to look similar to other FISC
manuals at the completion of stake holder review. Page breaks and
column formatting will be different. Graphics will be cleaned up.
Intended audience is sub-contracted 2-way shops that have signed a
NDA and have a SOW.
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
© 2007,
BAE Systems Information and Electronic Systems Integration Inc.. All rights
reserved
The information contained in this manual is the property of BAE Systems and is
intended for the purchaser’s use only. It may not be reproduced without the express
written consent of BAE Systems.
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Table of Contents
List of Illustrations ........................................................................................................ 2
List of Tables ................................................................................................................. 2
Warnings and Precautions ........................................................................................... 3
1.0
Introduction......................................................................................................... 6
2.0
First InterComm™ System Description ........................................................... 6
2.1 Vehicle Communications Assembly, Model VCA100.................................... 8
2.2 VCA100 Power Connector ........................................................................... 9
2.3 WiFi Antenna ................................................................................................ 9
2.4 Land Mobile Radio Antenna ......................................................................... 9
3.0
Planning the Installation .................................................................................. 10
3.1 Installation Kit Components ........................................................................ 10
3.2 Tools and Test Equipment.......................................................................... 11
3.3 System Component Locations.................................................................... 12
3.3.1
VCA100........................................................................................ 12
3.3.2
WiFi Antenna................................................................................ 12
3.3.3
Land Mobile Radio Antenna ......................................................... 13
3.3.4
Power and Fuse ........................................................................... 13
3.3.5
Manual Switch .............................................................................. 13
4.0
Installation Procedures.................................................................................... 14
4.1 VCA100 Unit............................................................................................... 14
4.2 WiFi Antenna .............................................................................................. 14
4.3 Land Mobile Radio Antenna ....................................................................... 15
4.4 DC Power ................................................................................................... 15
4.5 VCA100 On/Off Switch ............................................................................... 16
4.6 Fuse Assembly ........................................................................................... 16
5.0
Initial Power Test .............................................................................................. 17
6.0
Programming Procedure.................................................................................. 18
6.1 Preparation ................................................................................................. 18
6.2 VCA100 Update Procedure ........................................................................ 19
7.0
Unit Test Plan.................................................................................................... 20
7.1 LMR Antenna VSWR Test .......................................................................... 20
7.2 System Functional Test .............................................................................. 20
8.0
Troubleshooting ............................................................................................... 21
9.0
BAE Support Information................................................................................. 21
10.0
Companion Documentation............................................................................. 21
Appendix A Recommended LMR Antennas.............................................................. 22
Appendix B VCA100 Software Programs and Utilities............................................. 23
B.1 BAE Systems VCA Manager Program ....................................................... 23
A29799 rev A
Page 1
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
B.2 Serial IP Program ....................................................................................... 26
B.3 Kenwood Radio Programming Software..................................................... 27
Appendix C Acronyms and Abbreviations................................................................ 29
Appendix D Troubleshooting Procedures ................................................................ 30
Appendix E Installation Sign Off Sheet ..................................................................... 31
List of Illustrations
Figure 1. Typical VCA100 Vehicle Installation................................................................ 7
Figure 2. First InterComm™ System VCA100 Unit ....................................................... 8
Figure 3. VCA100 Power Harness Connector – Front View........................................... 9
Figure 4. Standard Comtelco WiFi Antenna ................................................................... 9
Figure 5. In-Line Fuse .................................................................................................. 13
Figure 7. VCA100 Mounting Bracket ............................................................................ 14
Figure B-1.1 First InterComm™ VCA Manager Window ............................................. 23
Figure B-1.2 VCA Manager Internet Explorer Window ................................................. 24
Figure B-1.3 VCA Manager Configuration Window ...................................................... 24
Figure B-1.4 First InterComm™ VCA Manager Help Window..................................... 25
Figure B-2.1 Serial IP Control Panel and Select Port Windows ................................... 26
Figure B-2.2 Serial IP Program Configuration Wizard .................................................. 27
List of Tables
Table 1. First InterComm™ System VCA100 Models ................................................... 8
Table 2. VCA 100 Vehicle Installation Kit ..................................................................... 10
Table 3. Installer-Supplied Parts .................................................................................. 10
Table 4. Required Equipment and Software................................................................. 11
Table 5. Recommended Tools for First InterComm™ System Installation .................. 11
Table 6. Initial Power Tests .......................................................................................... 17
Table 7. Required User Information ............................................................................. 18
Table 8. VCA100 Update Procedure ............................................................................ 19
Table 9. LMR Antenna VSWR Test Results................................................................. 20
Table 10. System Functional Test Results ................................................................... 20
Table A-1. Recommended LMR Antennas................................................................... 22
Table A-2. LMR Antenna Specifications....................................................................... 22
Table B-1 VCA100Model Characteristics ...................................................................... 28
Table B-2 Required Kenwood Radio Parameters To Be Programmed ......................... 28
Page 2
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Warnings and Precautions
Federal Communications Commission (FCC)
Compliance - This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. Further, proper installation does not guarantee that
interference will not occur in a particular situation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and affected receiver.
• Connect equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult an experienced radio/TV technician for help.
Radio Frequency Exposure Compliance – The First InterComm™ System generates and uses RF
energy. Pursuant to FCC rules for the Maximum Permissible RF Exposure the antenna(s) specified in
this manual MUST be installed so as to provide a separation distance of at least 18 inches (45 cm) from
all persons. Additionally, the unit may not be used to transmit for more than 50% of the time (average
duty cycle over a 30 minute period).
Users must not change the antenna types or their location at the risk of voiding the conditions of their
FCC license and/or the conditions to which the product has been certified (consult your installer in these
cases). Changes or modifications to the equipment may cause harmful interference unless the
modifications are expressly approved in the installation manual. The authority to operate the equipment
could be lost, if an unauthorized change or modification is made.
Electromagnetic Interference/Compatibility
Nearly every electronic device is susceptible to electromagnetic interference (EMI) if inadequately
shielded, designed, or otherwise configured for electromagnetic compatibility. It may be necessary to
conduct compatibility testing to determine if any electronic equipment used in or around vehicles is
sensitive to external RF energy or if any procedures need be applied to eliminate or mitigate the potential
for interaction between the First InterComm™ System and other equipment or devices.
• Facilities – To avoid EMI or compatibility conflicts, turn off the First InterComm™ System near any
facility where posted notices instruct you to do so; e.g., hospitals or health care facilities.
• Vehicles – To avoid possible interaction between First InterComm™ System and vehicle electronic
control modules (e.g., ABS, engine, or transmission controls), the First InterComm™ System should
be installed only by a professional installer.
• Pacemakers – Maintain a minimum separation of 12 inches between First InterComm™ System
components (the VCA100 and associated antennas) and any pacemaker to avoid potential
interference with pacemaker function.
A29799 rev A
Page 3
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
General Precautions
•
DC Power – Ensure that power into the First InterComm™ System does not exceed 24VDC.
•
Explosive Environments – Ensure the First InterComm™ System is turned off before entering a
blasting area, or in areas posted “TURN OFF TWO-WAY RADIO”. Sparks in a potentially explosive
atmosphere can cause an explosion or fire resulting in bodily injury or death.
Page 4
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
First InterComm System
Installation Checklist
Plan First InterComm™ System (FICS) equipment locations on the vehicle,
Section 3.
Perform Vehicle Installation, Section 4.
Perform DC Power Test, Section 5
Fill out Table 7, “Required User Information”. Provide copies to Customer, and
BAE Systems, and retain file copy.
Perform VCA100 Programming, Section 6.
Perform Unit Test Plan, Section 7.
Fill out “Installation Sign Off Sheet”, Appendix E. Obtain required signatures
and send to BAE Systems, retain file copy.
A29799 rev A
Page 5
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
1.0
Introduction
The First InterComm™ System (FICS) allows first responders from different agencies at
an emergency incident to readily communicate with one another, even though their
radios operate on different frequencies; i.e., VHF, UHF or 800 MHz systems, both digital
and analog. The FICS can accommodate any new communication technologies,
including operating systems in the 700-MHz band.
Only one vehicle from each on-scene department is required to have an installed FICS
unit to enable linking dissimilar radio networks. There is no requirement for special
equipment, stand-alone towers, or other costly infrastructure.
An optional capability included with the FICS is Talk Group Software that allows the
Incident Commander (IC), using a standard laptop computer with Wireless Fidelity (WiFi) capability, to monitor system status and to control communications. FICS Talk
Group Software significantly enhances the system, but is not required for voice
interoperability; the latter is provided by the VCA100 and associated antennas alone.
The Department of Homeland Security (DHS) has designated the FICS as a Qualified
Anti-Terrorism Technology under the SAFETY Act. The FICS Supports the National
Incident Management System (NIMS), and is included in the Memorial Institute for the
Prevention of Terrorism (MIPT) “Responders Knowledge Base” and the InterAgency
Board's (IAB) “Standard Equipment List”.
Finally, it is important to note that using the FICS does not require changes to Standard
Operating Procedures (SOP). Rather, it provides day-to-day voice interoperability at an
incident scene, and offers improved coordination of on-site first responder personnel.
This installation guide contains information for the proper installation of the FICS. We
strongly recommended that the system be installed in accordance with this guide,
understanding that concessions may be needed for specific vehicles. This guide
assumes that the system installer is qualified, familiar with the intended vehicle, and
possesses the proper tools.
2.0
First InterComm™ System Description
The FICS (Figure 1 below) consists of:
•
VCA100 unit, matched to user’s existing radio network frequencies
•
Vehicle-mounted Wireless Fidelity (Wi-Fi) antenna
•
Vehicle-mounted Land Mobile Radio (LMR) antenna, matched to user’s existing
radio network frequencies
•
Remote On/Off switch
•
FICS Talk Group Software (optional capability)
Page 6
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
The system operates on 12VDC vehicle power through an independent cab-mounted
switch. There are no speakers, microphones, or other vehicle tie-ins.
Eleven VCA100 models are available to cover the LMR bands (see Table 1 below). The
LMR antenna must match the frequency band of the VCA100 model being installed. A
standard, roof mounted 2.4 GHz 802.11 antenna is used for all VCA100 models.
Figure 1. Typical VCA100 Vehicle Installation
A29799 rev A
Page 7
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Table 1. First InterComm™ System VCA100 Models
Model
Protocol
Encryption
LMR Band
VCA100-L1FCGX
VCA100-L2FCGX
VCA100-V1FCGX
VCA100-V1PCGX
VCA100-V1PAGX
VCA100-V1PDGX
VCA100-U1FCGX
VCA100-81FCGX
VCA100-81PCGX
VCA100-81PDGX
VCA100-91FCGX
FM
FM
FM
FM/P25
FM/P25
FM/P25
FM
FM
FM/P25
FM/P25
FM
None
None
None
None
DES/AES
DES
None
None
None
DES
None
VHF Low Band
VHF Low band
VHF High Band
VHF High Band
VHF High Band
VHF High Band
UHF
800
800
800
900
2.1
Kenwood Radio
Module
TK-190K
TK-190K2
TK-2180K
TK-5210K
TK-5210K
TK-5210K
TK-3180K
TK-480SK
TK-5400K
TK-5400K
TK-481SK
Frequency
Range
29.7 – 37 MHz
35 – 50 MHz
136 - 174 MHz
136 - 174 MHz
136 - 174 MHz
136 - 174 MHz
450 - 520 MHz
806 - 870 MHz
806 - 870 MHz
806 - 870 MHz
896 - 941 MHz
Vehicle Communications Assembly, Model VCA100
The VCA100 (Figure 2 below) is mounted in a vehicle and has no operator controls
other than a remote power-on switch. Once initialized, VCA100 operations are
transparent to the operator. Responders need only set their radio equipment to the predesignated interoperability channel to monitor or speak to members of other radio
networks at the site. The specific VCA100 model is selected based on the radio
frequencies used by the participating department (see Appendix A).
• LMR:
• GPS:
• Ethernet:
• Power:
• Network:
2-way radio antenna connection, TNC.
Reserved for future implementation.
Activity
Indicator
Factory use only.
Nominal 13.6V DC and 1.75 A max
On/Off control is via cab mounted switch toggle switch
Wireless antenna port A, reverse polarity SMA connector.
• Activity Indicator: Power On, Built in Test indicator light.
Figure 2. First InterComm™ System VCA100 Unit
Page 8
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
2.2
VCA100 Power Connector
The VCA100 uses three (3) pins of a 6-pin Molex connector as shown in Figure 3.
Gnd
NC
NC
+12
VDC
Pwr
+12
VDC
Switch
NC
Front View of
Molex Connector
Figure 3. VCA100 Power Harness Connector – Front View
2.3
WiFi Antenna
The standard WiFi antenna for all VCA100 installations is the Comtelco Model A10245B
(Figure 4), a 2.4 GHz 802.11 roof mounted antenna, with elevated feed to rise above
cab obstructions and light bars. Gain is 3 dBi without ground plane, 5 dBi with ground
plane. Through mount is the Comtelco Model MBZM-10R/PI with 14’ micro-loss cable
and factory terminated SMA connector.
Height:
14 inches
Mount:
Standard TAD/NMO
Gain:
5 dBi with ground plane
Mechanical:
Built-in shock spring
Figure 4. Standard Comtelco WiFi Antenna
2.4
Land Mobile Radio Antenna
A LMR antenna must match the frequency of the specific VCA100 model being installed
on the vehicle. Appendix A lists recommended LMR antennas that may be used with
various VCA100 models.
A29799 rev A
Page 9
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
3.0
Planning the Installation
3.1
Installation Kit Components
Table 2 lists the deliverable installation kit for the First InterComm™ System. Specific
antennas will vary depending on the LMR frequency. The material listed is based on
availability; equivalent products may be used.
Table 2. VCA 100 Vehicle Installation Kit
Description
Vehicle Communications Assembly Model 100 (VCA100)
*includes screw, harness, and bracket below
VCA100 Mounting Bracket
VCA100 Power Harness
Screws, center sunk head, #6-32 x .500 lg
12 VDC Power Cable, 16 AWG (red) for Specification
SAEJ1128
12 VDC Power Cable, 20 AWG (orange) for Specification
SAEJ1128-GPT
Butt Splice, 16 ga Environmentally Sealed
Butt Splice, Step Down, 16ga to 20 ga, environmentally
sealed
Butt Splice, 20 ga Environmentally Sealed
ATO/ATC Fuse Holder with GXL wire
ATO/ATC Fuse, 10 A
LMR Antenna, through mount, with hardware
WiFi Antenna, elevated feed, 5dBi gain, 2.4GHz, through
mount, 3/4-inch hole
WiFi Through mount base and14’ cable with reverse
polarity (female) SMA connector
Part Number
Model number is
frequency dependent
Vendor
BAE Systems
Qty
BAE001131-01-LF
8422765-2
na
WX16-2 (SXL 16 ga)
BAE Systems
BAE Systems
na
Waytek, Inc
20’
WG20-3 (GPT 20 ga)
Waytek, Inc
15’
31980
38058
Waytek, Inc
Waytek, Inc
30980
46047
46210
Various
A10245B
Waytek, Inc
Waytek, Inc
Waytek, Inc
Multiple
Comtelco
CEZM10-RP
Comtelco
Table 3 lists typical Installer-supplied parts that are vehicle specific and not supplied
with the kit.
Table 3. Installer-Supplied Parts
Description
SPST Switch, illuminating, 1 A (minimum)
Ground Wire, 18 AWG (black)
Ring Terminal, size as needed (Gnd)
Terminals, size as needed (switch)
Terminal, size as needed (main power cut in)
Grommet, rubber, various sizes
Cable Ties, Nylon
Cable Tie mount, 4-way
Screws, self tapping, #8-32, .500 lg
Washers, size and type as needed
Page 10
Part Number
44206 or similar
Varies
Varies
Varies
Varies
Varies
Varies
Varies
Varies
Varies
Vendor
Waytek, Inc
Varies
Varies
Varies
Varies
Varies
Varies
Varies
Varies
Varies
Quantity
As Required
As Required
As Required
As Required
As Required
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
3.2
Tools and Test Equipment
Table 4 lists details of the test equipment and software required to install the FICS
VCA100. These comprise:
•
A laptop computer equipped with WiFi capability, loaded with Windows® XP1
Operating System, Service Pack 2, and BAE Systems supplied software (required to
upload user-specific parameters into the VCA100). The laptop is also used to test
the FICS VCA100 after installation.
•
A watt meter to perform VSWR test.
•
A volt/ohmmeter to perform voltage and resistance checks.
Table 4. Required Equipment and Software
Description
Laptop PC with Windows XP, Service Pack 2
BAE Systems approved 2.4 GHz Wireless
Network Card
BAE Systems First InterComm™ System
Installers CD
Voltage/Resistance Meter (DVM or VOM)
Watt Meter w/ cables, slugs, and adapters
Part Number
Varies
List to be provided
Vendor
Varies
List to be provided
Quantity
TBD
BAE Systems
Varies
Model 43 or
equivalent
Varies
Bird or equivalent
Table 5 lists recommended tools for the First InterComm™ System installation.
Equivalent substitutes may be used as necessary.
Table 5. Recommended Tools for First InterComm™ System Installation
Tool
Screwdrivers, Phillips Head
Non-insulated Crimp Tool
Crimp Tool, Ratcheting Coaxial
Hole Saw, 3/4-inch with depth
protection
Non-Metallic Fish Tape
Clutch-type Screw Gun
Pliers
Electric Drill
De-Burring Tool
Socket Set
Wire Cutters
RF Cable Termination Kit
Heat Gun
Model/Specification
#1 and #2 flathead
Thomas & Betts WT-111-M
Cambridge 24-9960P
Ripley HSK 19 or Antenex® HS34
Klein-Lite® 50156, 25 feet
Makita® #6096DWE, #1 and #2 Phillips-Head bits
Slip Jaw
3/8-inch, with HSS bits
Quarter Inch
Flush-cut and large
For SMA and TNC connectors
Windows is a registered trademark of Microsoft Corporation
A29799 rev A
Page 11
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
3.3
System Component Locations
WARNING
WHEN SELECTING LOCATIONS FOR FIRST INTERCOMM™ SYSTEM COMPONENTS,
AVOID HIGH FREQUENCY (HF) NOISE PRODUCERS AND DO NOT RUN DC POWER
FEEDS TO THE VCA100 PARALLEL TO IGNITION CIRCUITS, ELECTRONIC MODULES,
OR SIMILAR ITEMS. AVOID RUNNING POWER LEADS IN PARALLEL WITH VEHICLE
WIRING OVER LONG DISTANCES.
3.3.1
VCA100
The VCA100 has no operator interfaces other than an activity indicator. Also, the unit
has no fan; it is convection cooled and does not require any special ventilation.
However, it is not environmentally sealed and must be installed in a protected area
where it will not be exposed to any fluids (THE ENGINE COMPARTMENT IS NOT ACCEPTABLE).
The optimum location is one in which the VCA100 is out of the way, its face plate and
cable connections protected as much as possible, and there are at least six inches of
space around the VCA100 to allow air circulation. Additionally, attempt to provide line of
sight to the activity indicator.
Plan for cable management and strain relief loops for the cables. Cable ties and
mounts are needed to prevent cable movement and vibration.
3.3.2
WiFi Antenna
The WiFi antenna location has highest priority because the antenna’s relatively short
range has the greatest effect on system performance. Mount the antenna as high as
possible on the cab roof, and as close as possible to the vehicle’s centerline to provide
360-degree coverage. The antenna requires a metal ground plane to achieve its full
5dBi of gain.
We recommend keeping the antenna at least 12 inches away from any light bars or
other antennas. The maximum designed distance from the VCA100 to the WiFi
antenna is 14 feet, the standard cable length that comes with the antenna. Extensions
are not recommended since they will significantly reduce the WiFi range. If an
extension cannot be avoided substitute the antenna mount with a cable of sufficient
length (no splices or adapters) and equivalent or better loss specifications at 2.4 GHz
than what is supplied.
Certain vehicles do not allow locating the antenna in the center or center-rear of the
roof. In this case, the next best antenna location is on the direct center of the trunk lid.
Be aware, however, that this location will degrade the WiFi range. The mounting area
under the antenna must be a flat, metallized ground plane.
Page 12
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
3.3.3
Land Mobile Radio Antenna
The LMR antenna must match the frequency of the specific VCA100 model being
installed on the vehicle. Many LMR antennas will require cutting to ensure proper
VSWR match on the customer’s frequency. Ensure that the new LMR antenna is not
installed in close proximity to any existing LMR antennas.
We recommend keeping the antenna at least 12 inches away from any light bars,
antennas, or other roof-mounted equipment.
3.3.4
Power and Fuse
The vehicle’s main power source is connected to the VCA100 by the DC power cable
(red) that passes through an inline fuse. Locate the fuse as close as possible to the
power source and splice it in with weatherproof butt splices (SUPPLIED). Mount the fuse
assembly (Figure 5) to facilitate maintenance. Splice the power line to the VCA100
power harness (SUPPLIED) using the step-down splice (SUPPLIED) to accommodate the
dissimilar wire gauges.
Figure 5. In-Line Fuse
3.3.5
Manual Switch
A second, low current, power line (orange) must run through a cab-mounted manual
toggle switch to the VCA100 power connector SWITCH input (pin 2). This switch is not
supplied in the deliverable installation kit because User-specific vehicle installations
vary; i.e., switch location is a function of User requirements and vehicle constraints. An
illuminated manual switch, appropriately labeled, is recommended. Connect the switch
to a 1-ampere fuse-protected vehicle power source.
A29799 rev A
Page 13
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
4.0
Installation Procedures
4.1
VCA100 Unit
1. Record the VCA100 model number and serial number on the INSTALLATION SIGN
OFF SHEET (see Appendix E). Tag is not viewable after mounting.
2. Carefully inspect the area selected for the VCA100 unit to ensure that the area is
free of physical or electrical obstacles that could interfere with proper installation,
maintenance, or operation.
3. Attach the two L-shaped mounting brackets (Figure 6) to the sides of the VCA100
using four #6-32 countersunk machine screws if holes are used, or thumbscrews if
quick-release slots are used. Attach the wide edge of the bracket to the VCA100;
attach the narrow edge to the vehicle.
4. Place the VCA100 in its final location and scribe three bracket holes into the
vehicle on each side of the VCA100 for drilling. The VCA100 must be firmly
mounted to the vehicle.
5. Pre-drill six holes into the vehicle to accommodate self-tapping screws. The size
of the hardware used determines the size of the holes.
6. Mount the VCA100 to the vehicle with self-tapping screws.
Figure 6. VCA100 Mounting Bracket
4.2
WiFi Antenna
1. Verify the center pin of the WiFi antenna cable connector is female (reverse
polarity SMA). Carefully inspect the area selected for the WiFi antenna to ensure
that the area is free of physical or electrical obstacles that could interfere with
proper installation, maintenance, or operation.
2. Follow manufacturer’s installation instructions for external mounting of the WiFi
antenna.
Page 14
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
3. Run the RF cable from the WiFi antenna to the VCA100. Use cable ties and
mounts to protect the cable. Grommet all through holes to prevent cable chaffing.
4. Connect the WiFi RF cable in a straight path to the VCA100 NETWORK A SMA
connector. Use cable ties and mounts to keep the cable from moving or placing
stress on the SMA connector.
4.3
Land Mobile Radio Antenna
1. Carefully inspect the area selected for the LMR antenna to ensure that the area is
free of physical or electrical obstacles that could interfere with proper installation,
maintenance, or operation.
2. Follow the LMR manufacturer’s installation instructions for mounting of the
antenna and for trimming it to the user’s frequency.
3. Run the RF cable from the LMR antenna to the VCA100. Use cable ties and
mounts to protect the cable. Grommet all through holes to prevent cable chaffing.
4. At the VCA100, lay in a stress relief loop and cut the LMR RF cable to length.
Terminate the cable with a TNC connector in accordance with manufacturer’s
instructions. Connect to the VCA100 LMR TNC connector.
4.4
DC Power
1. Carefully inspect the area selected for the DC power lines to ensure that the area is
free of physical or electrical obstacles that could interfere with proper installation,
maintenance, or operation.
2. Starting at the VCA100, locate a suitable chassis ground as close to the VCA100 as
possible. If necessary, scrape and remove paint to reach bare metal. Drill chassis
and use a self-tapping screw and star washer to create a chassis ground.
3. Locate the 20 AWG ground (black) wire of the VCA100 power harness (Pin 4). Cut
and strip the outer cable jacket as required. Cut the end of the ground wire to
length, terminating with a ring terminal, and secure the terminal to the chassis
ground created in Step 2 (see Figure 3).
4. Lay in a stress relief loop and use cable ties and mounts to secure the power
harness to the vehicle and prevent vibration or strain on the power connector.
5. Connect a suitable length of red 16 AWG wire to the VCA100 power harness main
power (red) wire (Pin 1) (see Figure 3) using the 16 to 20 step-down environmental
splice (SUPPLIED). Run the other end of the wire to the VCA100 in-line fuse. Use
cable ties and mounts to protect the cable. Grommet all through holes to prevent
cable chaffing.
6. Connect a suitable length of orange 20 AWG wire to the VCA100 power harness
12V Switch (white) wire (Pin 2) (see Figure 3) using the 20 AWG environmental
splice (SUPPLIED). Run the other end of the wire to the planned location of the
A29799 rev A
Page 15
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
VCA100 On/Off Switch. Use cable ties and mounts to protect the wire. Grommet all
through holes to prevent cable chaffing.
4.5
VCA100 On/Off Switch
1. Carefully inspect the area selected for the VCA100 On/Off Switch to ensure that the
area is free of physical or electrical obstacles that could interfere with proper
installation, maintenance, or operation.
2. Drill or cut an area to hold the lighted toggle switch. Mount and label the switch.
3. If the switch is illuminated, locate a suitable chassis ground as close to the new
power switch as possible. If necessary, scrape and remove paint to reach bare
metal. Drill chassis and use self-tapping screw and star washer to create a chassis
ground for the switch.
4. I f the switch is illuminated, connect a suitable length of black 20 AWG wire to the
ground lug of the VCA100 On/Off switch using an appropriate terminal. Cut other
end to length, terminate with a ring terminal, and secure the assembly to the chassis
ground created in step 3 above.
5. Locate the end of the orange 20 AWG switch extension wire from the VCA100
power harness and cut it to length to mate with the VCA100 On/Off switch. Connect
the wire to the power out lug of the VCA100 On/Off switch using an appropriate
terminal.
6. Use an appropriate terminal to connect a suitable length of orange 20 AWG wire to
the power in lug of the VCA100 On/Off switch. Connect the other end of the wire to
a 1A fuse-protected vehicle power source with appropriate terminal. Use cable ties
and mounts to protect the wire. Grommet through holes to prevent cable chaffing.
7. Reassemble any panels or consoles opened for installation of the switch.
4.6
Fuse Assembly
1. Carefully inspect the area selected for the fuse assembly to ensure that the area is
free of physical or electrical obstacles that could interfere with proper installation,
maintenance, or operation.
2. Drill into the vehicle at the proper location to receive the Fuse Assembly’s cap and
mounting tab. Remove fuse from holder and mount holder using a self-tapping
screw.
3. Locate the end of the red 16 AWG extension wire from the VCA100 Power harness
and cut it to length to mate with one end of the Fuse Assembly. Connect it to the
Fuse Assembly using a 12AWG environmental splice (SUPPLIED).
4. If the Fuse Assembly lead is too short, use an environmental splice (SUPPLIED)
connected to a suitable length of red 16AWG wire to extend the lead.
5. Connect the Fuse Assembly’s other wire to the vehicle’s load center or main
+12VDC power source using the appropriate termination.
Page 16
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
6. Use cable ties and mounts to protect the wire. Grommet all through holes to prevent
cable chaffing. Install VCA100 Fuse.
5.0
Initial Power Test
1. Before connecting to the VCA100, use a voltmeter at the VCA100 power harness
connector to check for a constant +12VDC, switched +12VDC, and ground (Figure 3
shows the VCA100 power connector).
2. Follow the steps as listed in Table 6. Correct any problems encountered before
proceeding to the next step.
3. Place check mark in Verified box after successful completion of test step.
Table 6. Initial Power Tests
Gnd
NC
NC
+12
VDC
Pwr
+12
VDC
Switch
NC
Step
Front View of
Molex Connector
Required Equipment: Volt/Ohm Meter
Procedure
Verify VCA100 power harness is
disconnected from VCA100 and energized
Expected Result
VCA100 power harness
disconnected and energized
Probe the VCA100 power harness connector
Pin 1 for a constant +12 VDC
Voltmeter reads vehicle power
as approximately +12VDC
Set the VCA100 power switch to ON
Power switch is ON
Probe the VCA100 power harness connector
pin 2 for switched +12 VDC
Voltmeter reads vehicle power
as approximately +12VDC
Set the VCA100 power switch to OFF
VCA100 is OFF
Probe the VCA100 power harness connector
pin 2 for switched +12 VDC
Voltmeter reads 0 VDC
Probe VCA100 power harness connector pin
4 (ground) to chassis ground with ohmmeter
Good ground connection exists
Connect VCA100 power harness to VCA100.
Items are connected.
Turn on VCA100 unit and monitor Activity
LED (see Figure 2) for Power On Built In Test
(PBIT) Result.
LED will illuminate for approx. 30 sec. during
initialization, extinguishes for 10 sec., then
illuminates and remains on if Power-on BIT is
successful.
Power-on BIT is successful.
A29799 rev A
Verified
Page 17
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
6.0
Programming Procedure
The VCA100 is delivered with operating software but must be updated with user-specific
parameters. Programming is done in two parts:
• BAE Systems’ supplied VCA MANAGER Program and utilities is used to update the
flash or to load new operating software.
• Installer supplied Serial/IP COM Port Redirector and Kenwood Radio programming
software is used to update the radio module.
All programming is done wirelessly by loading the software on an Installer supplied
maintenance laptop equipped with a BAE Systems approved wireless network card.
6.1
Preparation
1. Appendix B contains instructions for operating the Serial IP and the VCA MANAGER
Programs. See Kenwood documentation for operation of that software.
2. Consult with the end user department and discuss incorporating the VCA100 into
their standard operating procedures.
3. Collect and record the required VCA100 User information in Table 7.
4. Provide copies to Customer, BAE Systems, and retain copy for records.
Table 7. Required User Information
Item
Parameter
Department Name
Format
Up to 128 Characters.
Vehicle ID
Up to 128 Characters.
Vehicle Type
Icon on WiFi network, e.g., fire,
police, ambulance.
Nickname
Up to 16 Characters
LMR Bandwidth
Wide (25 kHz) or
Narrow (12.5 kHz)
LMR Mode
Analog or Digital
LMR Transmit Power
High or Low
LMR Transmit Frequency
Numeric entry in MHz
LMR Receive Frequency
Numeric entry in MHz
10
LMR Transmit Private Line
Code
Frequency or Alphanumeric ID
[e.g. 94.8Hz (2A)]
11
LMR Receive Private Line
Code
Frequency or Alphanumeric ID
[e.g. 94.8Hz (2A)]
12
VCA100 ID
Serial number on unit
Page 18
User Data
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
6.2
VCA100 Update Procedure
1. Perform the update in two parts: VCA MANAGER program and Kenwood Radio
software.
2. Follow the steps as listed in Table 8. Correct any problems encountered before
proceeding to the next step.
3. Place check mark in Verified box after successful completion of test step.
Table 8. VCA100 Configuration Procedure
Required Items:
a. VCA100 Installed in vehicle
b. User Parameters (Table 7 of this document).
c. Installer’s WiFi Laptop configured using BAE Systems’ software CD
d. Serial IP and Kenwood Radio programming software installed on laptop
Step
Procedure
Expected
Result
Turn on VCA100. Wait one minute for boot up to complete.
Booted
Turn on the laptop and connect to First_InterComm_Network.
Connected
Execute VCA MANAGEMER program (see Appendix B in this
document) and input specific User Parameters. VCA100 will
reboot after committing changes.
Updated and
Rebooted
Launch Serial IP program. (see Appendix B in this document)
Running
Use Serial IP program to enable a virtual COM port between
COM2 and the VCA100. (see Appendix B in this document)
Enabled
Launch the appropriate Kenwood Radio programming software for
the VCA100 and set COM port to COM2. (see Table 1, First
InterComm™ System VCA100 Models)
Running,
COM2
Program VCA100 Radio module with specific User LMR
frequencies and PL Codes.
Programmed
Close Kenwood, SERIAL IP and VCA MANAGER program. Prepare
to run System Functional Test of the Unit Test Plan to verify
updates.
Closed
A29799 rev A
Verified
Page 19
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
7.0
Unit Test Plan
Follow the test procedures described in Paragraphs 7.1 and 7.2. Correct any problems
found, retest, and record final results on the INSTALLATION SIGN OFF SHEET (Appendix E).
7.1
LMR Antenna VSWR Test
Perform an antenna VSWR test using an in-line wattmeter with appropriate frequency
range and power levels, and low loss cable and connectors. The LMR output is
expected to be in the range of 3 to 5 watts. Record results in Table 9.
Table 9. LMR Antenna VSWR Test Results
Required Material:
a. VCA100 installed in vehicle with LMR Antenna and cable under test
b. Antenna OEM’s VSWR procedure (or standard industry accepted VSWR procedure)
c. Watt meter
Step
Procedure
7.2
Perform LMR VSWR procedure. Record result.
Requirement
Result
< 2:1 VSWR (10%)
System Functional Test
1. Follow the test steps in Table 10 to verify the VCA100’s key functions and its ability
to operate in a network.
2. Correct any problems found, retest, and record final results on the INSTALLATION SIGN
OFF SHEET (Appendix E).
3. Obtain required signatures and send to BAE Systems, retain file copy.
Table 10. System Functional Test Results
Required Material:
a. VCA100 under test installed in vehicle and configured with user parameters.
b. Known good user mobile or portable radio with the same Frequency and PL Code as the
VCA100 under test.
c. Known good second VCA100 and mobile or portable radio set to a different frequency than the
VCA100 under test with a line-of-sight path more than 100 feet but less than 300 feet
separation between the VCAs.
Step
Procedure
Turn on VCA100 under test. Wait one minute for boot
up to complete.
Turn on mobile or portable radio associated with the
VCA100 under test. Verify the proper channel is
selected.
Turn on known good second VCA100. Wait one minute
for boot up to complete.
Turn on mobile or portable radio associated with known
good VCA100. Verify proper channel is selected.
Page 20
Expected Result
Verified
Boot up complete
Proper channel selected
Boot up complete
Proper channel selected
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
8.0
Verify 2-way communication through both units occurs
without distortion, breakup, or dropouts. Record final
result on Installation Sign Off Sheet.
Communication is good
Troubleshooting
Appendix D contains detailed troubleshooting procedures for the FICS.
IMPORTANT
9.0
•
If the FICS appears to interfere with incident site operations,
immediately turn off every VCA unit (and FICS Talk Group Software if
in use), and return to normal SOP.
•
If Talk Group Software or Incident Commander Workstation (laptop)
computer problems occur, the VCA100 units will remain in their last
assigned Talk Groups. If the laptop or software is not functional, and
communication is needed between all responders, power-cycle all
VCA100s.
BAE Support Information
•
Telephone Support:
(603) 759-1027
•
E-Mail:
firstintercomm.eis@baesystems.com
•
Web:
http://www.firstintercomm.com
10.0 Companion Documentation
•
First InterComm™ System User Guide, Document No. A29798.
•
First InterComm™ System Talk Group Software, Document No. A29800.
A29799 rev A
Page 21
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Appendix A
Recommended LMR Antennas
Table A-1. Recommended LMR Antennas
Model
VCA100-L1FCGX
VCA100-L2FCGX
VCA100-V1FCGX
VCA100-V1PCGX
VCA100-V1PAGX
VCA100-V1PDGX
VCA100-U1FCGX
VCA100-81FCGX
VCA100-81PCGX
VCA100-81PDGX
VCA100-91FCGX
Suggested Antennas
C27, C30, C34
C34, C37, C40, C47
B1323
B1323
B1323
B1323
B4503, B4703, B4903
B8063
B8063
B8063
B8963
LMR Band
VHF Low Band
VHF Low band
VHF High Band
VHF High Band
VHF High Band
VHF High Band
UHF
800
800
800
900
Frequency Range
29.7 – 37 MHz
35 – 50 MHz
136 - 174 MHz
136 - 174 MHz
136 - 174 MHz
136 - 174 MHz
450 - 520 MHz
806 - 870 MHz
806 - 870 MHz
806 - 870 MHz
896 - 941 MHz
Protocol
FM
FM
FM
FM/P25
FM/P25
FM/P25
FM
FM
FM/P25
FM/P25
FM
Encryption
None
None
None
None
DES/AES
DES
None
None
None
DES
None
Table A-2. LMR Antenna Specifications
Manufacturer
Laird
Laird
Laird
Laird
Laird
Laird
Laird
Laird
Laird
Laird
Laird
Laird
Part Number
C27
C30
C34
C37
C40
C47
B1323
B4503
B4703
B4903
B8063
B8963
Page 22
Frequency
(MHz)
26.75-31
30-35
34-37
37-40
40-47
47-50
132-174
450-470
470-490
490-512
806-866
896-970
Gain
(dBi)
Unity
Unity
Unity
Unity
Unity
Unity
Wave
Length
1/4
1/4
1/4
1/4
1/4
1/4
5/8
5/8
5/8
5/8
5/8
5/8
Load
Tunable
Coil Style
Coil Style
Coil Style
Coil Style
Coil Style
Coil Style
Coil Style
Coil Style
Coil Style
Coil Style
Base
Base
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Height
(inches)
52.5
52.5
52.5
52.5
52.5
52.5
57
13
12.5
12.5
4 7/8
4 7/8
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Appendix B
VCA100 Software Programs and Utilities
B.1 BAE Systems VCA Manager Program
The VCA Manager is used to connect wirelessly to the VCA100 in order to change User
parameters and upgrade software on the VCA100. The procedure is to:
1. Power up the VCA100(s) that will be updated and then power up the laptop so that a
First InterComm Network is established.
2. Launch the First InterComm VCA Manager software using the Windows start button
to navigate to First InterComm and click on the VCA Manager menu item.
Figure B-1.1 First InterComm™ VCA Manager Window
3. VCAs in the network will will be listed in the top field of the window. Click on
Configure next to the serial number of the VCA to be updated.
4. An Internet Explore window will open for that VCA. Click on Configure VCA100.
A29799 rev A
Page 23
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Figure B-1.2 VCA Manager Configuration Tool
5. Enter user name and password in the pop up window and click Validate. (See your
BAE Systems representative for your user name and password.)
Figure B-1.3 VCA Manager Configuration Window
Page 24
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
6. Fill in the fields with new parameter information. Click on Commit to update.
Figure B-1.4 First InterComm™ VCA Manager Help Window
7. Clicking on Help will open the VCA00 manger Help page, which provide detailed
information about each of the data fields.
8. If the VCA100 software requires upgrading, click on Upload new software image at
the main VCA100 Internet Explorer window (Figure B-1.2). Log in with name and
password then click on Browse and navigate to the location of the new software file.
9. Click on the filename to enable the Update button. The field next to the button will
display the filename.
10. Click on Update and monitor progress.
11. Perform the SYSTEM FUNCTIONAL TEST described in Paragraph 7.2 to verify that the
newly programmed VCA100 communicates with other VCA100 units.
A29799 rev A
Page 25
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
B.2 Serial IP Program
Serial/IP Redirector software, a utility program, creates a virtual COM port that
associates an IP address with a hardware COM port. This allows RS-232 programming
with Kenwood software over a wireless link to the VCA100 Radio Module. The
procedure is to:
1. Start the VCA MANAGER PROGRAM (Paragraph B.1) to enable access to the First
InterComm™ network and the VCA100 being programmed.
2. Start the Serial IP Panel (Figure B-2) using the Windows start button; i.e.,
START Æ ALL PROGRAMS Æ SERIAL IP Æ CONTROL PANEL
3. Enter the target VCA100’s IP address into the IP ADDRESS BOX (10.0.0.X), where X is
the last digits of the unit’s serial number. Enter 7000 into the Port Number box.
4. Set the COM port to COM2 in the Serial IP Control Panel;
SELECT PORTS... Æ COM2Æ OK
5. Click on the Configuration Wizard (Figure B-3) in the SERIAL IP CONTROL PANEL.
6. Click Start in the wizard.
7. Watch the STATUS window in the Configuration Wizard to verify that the TELENET
session progresses successfully and that all check marks are green.
8. Click on Use Settings in the CONFIGURATION WIZARD to complete the Serial IP setup
and enable the virtual Com Port. (*NOTE: It is very easy to forget this step)
Figure B-2.1 Serial IP Control Panel and Select Port Windows
Page 26
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Figure B-2.2 Serial IP Program Configuration Wizard
B.3 Kenwood Radio Programming Software
Kenwood Radio Programming software is used as a utility program to configure the
VCA100 Radio Module.
NOTE
IT IS REQUIRED TO PROGRAM ALL RADIOS PER THE PARAMETERS IN TABLE B-2
BELOW.
The procedure is to:
1. Start the VCA Manager Program and Serial IP program (Paragraph B.1 & B.2
above) to link the COM2 port to the VCA100 being programmed.
2. Consult Table B-1 below to find the First InterComm™ System VCA100 Model and
then launch the corresponding Kenwood Radio programming software for the
VCA100 being programmed.
3. Set COM port used in the Kenwood software to COM2.
4. Consult Table B-2 below, Required Kenwood Radio Parameters To Be
Programmed, and program the values appropriate to the model being updated.
5. Consult Table 7, Required User Information, and program the appropriate values
into the VCA100 radio module.
A29799 rev A
Page 27
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Model
Protocol
Encryption
Frequency
Range
Kenwood
Radio Module
VCA100-L1FCGX
VCA100-L2FCGX
VCA100-V1FCGX
VCA100-V1PCGX
VCA100-V1PAGX
VCA100-V1PDGX
VCA100-U1FCGX
VCA100-81FCGX
VCA100-81PCGX
VCA100-81PDGX
VCA100-91FCGX
FM
FM
FM
FM/P25
FM/P25
FM/P25
FM
FM
FM/P25
FM/P25
FM
None
None
None
None
DES/AES
DES
None
None
None
DES
None
29.7 – 37 MHz
35 – 50 MHz
136 - 174 MHz
136 - 174 MHz
136 - 174 MHz
136 - 174 MHz
450 - 520 MHz
806 - 870 MHz
806 - 870 MHz
806 - 870 MHz
896 - 941 MHz
TK-190K
TK-190K2
TK-2180K
TK-5210K
TK-5210K
TK-5210K
TK-3180K
TK-480SK
TK-5400K
TK-5400K
TK-481SK
Kenwood
Radio Prgm
S/W
KPG-59D
KPG-59D
KPG-89D
KPG-95D
KPG-95D
KPG-95D
KPG-89D
KPG-49D
KPG-78D
KPG-78D
KPG-49D
Table B-1 VCA100Model Characteristics
TK-190K
120 sec
Disable
Minimum
Volume
Setting
TK-190K2
120 sec
Disable
n/a
TK-2180
120 sec
Disable
TK-3180
120 sec
Disable
TK-5210
120 sec
Disable
11
11
TK-5400
120 sec
Disable
13
n/a
TK-480
120 sec
Disable
n/a
Kenwood Radio
Module
Squelch
Level
Timeout
Warning Tone
Maximum
Volume
Setting
n/a
Table B-2 Required Kenwood Radio Parameters To Be Programmed
Page 28
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Appendix C
Acronyms and Abbreviations
ABS
AES
ATC
ATO
AWG
COM
DC
DES
DHS
EMI
EMS
FCC
FICS
FM
GPS
GXL
HF
HSS
IAB
IAN
IC
ID
IP
LED
LMR
MIPT
NIMS
NMO
OEM
P25
RF
SAE
SMA
SOP
SPST
TBD
TNC
UHF
VCA
VHF
VSWR
WiFi
Antilock Brake System
Advanced Encryption Standard
Automotive Blade-Type Fuse
Automotive Blade-Type Fuse
American Wire Gauge
Communication (port)
Direct current
Data Encryption Standard
Department of Homeland Security
Electromagnetic Interference
Emergency Medical Service
Federal Communications Commission
First InterComm™ System
Frequency Modulation
Global Positioning System
Brand name for a cross-linked polyethylene jacketed wire
High Frequency
High Speed Steel
InterAgency Board
Incident Area Network
Incident Commander
Identification
Internet Protocol
Light Emitting Diode
Land Mobile Radio
Memorial Institute for the Prevention of Terrorism
National Incident Management System
New Motorola
Original Equipment Manufacturer
Project 25 (digital encryption protocol)
Radio Frequency
Society of Automotive Engineers
Subminiature A-type (connector)
Standard Operating Procedures
Single Pole, Single Throw
To Be Determined
Threaded Neill-Concelman (connector)
Ultra High Frequency
Vehicle Communications Assembly
Very High Frequency
Voltage Standing Wave Ratio
Wireless Fidelity
A29799 rev A
Page 29
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Appendix D
Troubleshooting Procedures
To Be Supplied
Page 30
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
Appendix E
Installation Sign Off Sheet
I CERTIFY THAT THE FIRST INTERCOMM™ SYSTEM SUPPLIES AND
INSTALLATION SERVICES HAVE BEEN FURNISHED IN ACCORDANCE WITH
APPLICABLE CONTRACT REQUIREMENTS.
Site Name:
__________________________________________________
Site Location:
__________________________________________________
Vehicle VIN:
__________________________________________________
Vehicle Type / Model:
__________________________________________________
VCA100 S/N:
__________________________________________________
The undersigned agree that the Unit Test Plan has been satisfactorily completed,
with the exception of the outstanding items identified below, which must be
resolved per the list below in order for Customer to be fully satisfied.
______________________________________________________________________
Name, Title (BAE Systems Representative) Date___________________________
______________________________________________________________________
Name, Title (Customer)
Date ____________________________
OUTSTANDING ISSUES
Test Para.
Issue
A29799 rev A
Resolution Plan
Resolution
Page 31
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
First InterComm™ System VCA100 Installation Guide
THIS PAGE INTENTIONALLY LEFT BLANK
Page 32
A29799
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE
Systems Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without
the written permission of BAE Systems.
A29799 rev A
April 2008
PROPRIETARY INFORMATION: This document contains trade secrets and commercial or financial information that is the property of BAE Systems
Electronics and Integrated Solutions (E&IS). Further dissemination or disclosure of this information is strictly prohibited without the written permission
of BAE Systems.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
XMP Toolkit                     : 3.1-701
Producer                        : Acrobat Distiller 7.0.5 (Windows)
Create Date                     : 2008:11:03 14:17:08-05:00
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2008:11:03 14:17:08-05:00
Format                          : application/pdf
Creator                         : ralph.lombardo
Title                           : Microsoft Word - A29799 FIC VCA100 Installation Guide  Rev A Final.doc
Document ID                     : uuid:cedfabd5-06ff-42d7-a342-51ded53ca328
Instance ID                     : uuid:460047e4-aa82-40a7-afcb-656aad082745
Page Count                      : 35
Author                          : ralph.lombardo

EXIF Metadata provided by EXIF.tools