BBPOS WISEPAD WisePad User Manual WISEPAD Userguide V1 0 Eng

BBPOS Limited WisePad WISEPAD Userguide V1 0 Eng

User manual

Page1 of12Revision1.0Date17Mar2014WisepadUserGuide
Page2 of12Revision1.0Date17Mar2014Switch on Wisepad. Standby can be seen on LCD. Then press the Bluetooth button on red circle on figure shown, blue light is flashing. That means the Bluetooth module is ready to be paired.
Page3 of12Revision1.0Date17Mar2014
Page4 of12Revision1.0Date17Mar20142. OpentheAppforusingwisepad,andpresstheselectionkeyonthebottom,thereare4optionscouldbeseen.Upperleftcorner:ScanBluetoothUpperrightcorner:PairedDeviceLowerleftcorner:StopBluetoothLowerrightcorner:UnpairAllPressScanBluetoothtoconnectWisepad
Page5 of12Revision1.0Date17Mar20143 AfterconnectedBluetooth,BluetoothconnectedandMACAddresswillbedisplayedontheAPP,andWisepadReadywillbeshownonLCD.BluelightLEDwillkeepon.
Page6 of12Revision1.0Date17Mar2014UpperleftcornerGetDeviceinfoMiddleleft:CheckCardLowerleftcorner:SetAmountUpperrightcorner:ClearLogMiddleright:CancelCheckCardLowerrightcorner:StartEMV1. WisepadinfoandstatuscouldbegetafterpressGetDeviceinfo.ThedisplaylogcanbeclearedbypressingClearlog.
Page7 of12Revision1.0Date17Mar20142.UsercanperformswipecardorinsertICCcardafterpressCheckCardbutton
Page8 of12Revision1.0Date17Mar20142.1 Thefollowingexampleisafterasuccessfulswipecard
Page9 of12Revision1.0Date17Mar20142.2 Furtherdetailscouldbecheckedwithslidingmiddlelog.
Page10 of12Revision1.0Date17Mar20142.3 ICCCardInsertedwillbeshownafterinsertedanICCcardsuccessfully
Page11 of12Revision1.0Date17Mar20143. UsercouldperformasimulatedEMVtransactionafterpressStartEMV..4. PressDisconnectBluetoothtodisconnectthedevice,andBluetoothdisconnectedwillbeshown.WisepadwillresettoStandby.
Page12 of12Revision1.0Date17Mar2014FCCRequirementNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: – Reorient or relocate the receiving antenna. – Increase the separation between the equipment and receiver. – Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. – Consult the dealer or an experienced radio/TV technician for help. You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.M/N:WisePadFCCID:2AB7XWISEPADThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. 

Navigation menu