BBPOS WISEPAD WisePad User Manual WISEPAD Userguide V1 0 Eng
BBPOS Limited WisePad WISEPAD Userguide V1 0 Eng
BBPOS >
User manual
Page1 o
f
12
Revision1.0
Date17Mar2014
WisepadUserGuide
Page2 o
f
12
Revision1.0
Date17Mar2014
Switch on Wisepad. Standby can be seen on LCD. Then press the Bluetooth button on
red circle on figure shown, blue light is flashing. That means the Bluetooth module is
ready to be paired.
Page3 o
f
12
Revision1.0
Date17Mar2014
Page4 o
f
12
Revision1.0
Date17Mar2014
2. OpentheAppforusingwisepad,andpresstheselectionkeyonthebottom,there
are4optionscouldbeseen.
Upperleftcorner:ScanBluetooth
Upperrightcorner:PairedDevice
Lowerleftcorner:StopBluetooth
Lowerrightcorner:UnpairAll
PressScanBluetoothtoconnectWisepad
Page5 o
f
12
Revision1.0
Date17Mar2014
3 AfterconnectedBluetooth,BluetoothconnectedandMACAddresswillbe
displayedontheAPP,andWisepadReadywillbeshownonLCD.BluelightLED
willkeepon.
Page6 o
f
12
Revision1.0
Date17Mar2014
UpperleftcornerGetDeviceinfo
Middleleft:CheckCard
Lowerleftcorner:SetAmount
Upperrightcorner:ClearLog
Middleright:CancelCheckCard
Lowerrightcorner:StartEMV
1. WisepadinfoandstatuscouldbegetafterpressGetDeviceinfo.Thedisplaylog
canbeclearedbypressingClearlog.
Page7 o
f
12
Revision1.0
Date17Mar2014
2.UsercanperformswipecardorinsertICCcardafterpressCheckCardbutton
Page8 o
f
12
Revision1.0
Date17Mar2014
2.1 Thefollowingexampleisafterasuccessfulswipecard
Page9 o
f
12
Revision1.0
Date17Mar2014
2.2 Furtherdetailscouldbecheckedwithslidingmiddlelog.
Page10 o
f
12
Revision1.0
Date17Mar2014
2.3 ICCCardInsertedwillbeshownafterinsertedanICCcardsuccessfully
Page11 o
f
12
Revision1.0
Date17Mar2014
3. UsercouldperformasimulatedEMVtransactionafterpressStartEMV..
4. PressDisconnectBluetoothtodisconnectthedevice,andBluetoothdisconnected
willbeshown.WisepadwillresettoStandby.
Page12 o
f
12
Revision1.0
Date17Mar2014
FCCRequirement
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that changes or modifications not expressly approved by
the party responsible for compliance could void your authority to operate the
equipment.
M/N:WisePad
FCCID:2AB7XWISEPAD
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.