BUFFALO 09101731-0 Wireless LAN Card User Manual WLI CF S11G

BUFFALO INC. Wireless LAN Card WLI CF S11G

Users Manual Part 1 Revision 1

Wireless LAN Card WLI-CF-S11GUser's ManualBefore Operation1Windows CE Settings2Windows Me/98 3Windows 2000 Settings4Troubleshooting5Glossary6Specifications7WLI-CF-S11G.book i ページ ２００２年３月１日　金曜日　午後６時１６分
■ Precautions for radio signals● The wireless LAN card WLI-CF-S11G has been approved for conformityto the engineering standards as the wireless facility for a radio stationwith the low power data communication system based on the WirelessTelegraphy Act. Therefore, use of this LAN card does not require anyradio station license. The WLI-CF-S11G is allowed to be used in Japanonly.● Never use the WLI-CF-S11G near the magnetic field around amicrowave oven or in an area where static electricity and/or radio noise isgenerated. The radio signals may not be normally transmitted in theseareas.* When the WLI-CF-S11G is used near a wireless printer buffer(BUFFALO's RYP-G or similar products by other manufacturers) thatuse radio signals around 2.4 GHz, the processing speed of bothdevices may be adversely affected.● As the WLI-CF-S11G has been approved for conformity to theengineering standards, the following may be regarded as unlawful.• Disassembling/remodeling the WLI-CF-S11G• Removing the approval label from the rear of the WLI-CF-S11G● When it is necessary to set a radio channel other than the initial setting inthe WLI-CF-S11G, use the same frequency band as the followingequipment or wireless stations• Industrial, scientific, or medical equipment• Radio station for mobile identification used such as on a manufactureline in a factory①On-premise radio station (requiring a license)②Specific low power radio station (requiring no license)● Operating the WLI-CF-S11G may cause interference with the aboveequipment or radio stations. Thus, take precautions for the followingpoints1 Before using the WLI-CF-S11G, verify that no on-premise radiostation for mobile identification or no specific low power radiostation is operating near the WLI-CF-S11G.2 If an event of interference should be taken place by the WLI-CF-S11G with an on-premise radio station for mobile identification,WLI-CF-S11G.book 0 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual 1immediately change the frequency for this product to prevent theinterference.3 If you notice any trouble such as an event of interference caused bythe WLI-CF-S11G with a specific radio station for mobileidentification, contact your nearest sales representative.Operatingfrequency band2.4GHz　Modulation method DS-SSAssumedinterferencedistance40 m or lessFrequencychangeabilityUses the entire bandwidth, and can avoid the"on-premise radio station" and "specific lowerpower radio station" bands.WLI-CF-S11G.book 1 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual2ForewordThank you for purchasing BUFFALO's wireless LAN card WLI-CF-S11G.The WLI-CF-S11G is installed for wireless LAN communication incomputers equipped with a CompactFlash slot (type II) or PC card slot (typeII).Read this manual carefully before using the wireless LAN card to ensurecorrect operation.■ For your safety, be sure to follow the instructions given below.The following describes the instructions to avoid harming yourself, otherpeople, and properties, and to ensure safe operation of this product. Be sureto read and understand them thoroughly before using this product. Thismanual also contains instructions concerning general operation of thecomputer system to which this product is connected as well as thoseconcerning the product.Please take note that our warranty will not cover any failures and problemsof the computer, any losses and failures of data, or failures and problems ofthis product caused by misuse.Meanings of warning signsWarning Failure to follow the instructions shown with this signmay result in a hazard or serious injury to the user.CAUTION Failure to follow the instructions shown with this signmay result in injury to the user or property damage.WLI-CF-S11G.book 2 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual 3■Meanings of symbolsThis indicates warnings and cautions. Specific instructions are givenin or around △. (E.g., Exercise care to avoid an electric shock.)This indicates prohibited matters. Specific instructions are given inor around ○. (E.g., Do not disassemble.)This indicates compulsory rules. Specific instructions are given in oraround ●. (E.g., Disconnect the plug from the receptacle.)WARNINGNo disassemblyDo not disassemble or modify the product.It may cause fire or electric shock.UnpluggingTurn off the power to the computer and peripheraldevices immediately and unplug them if you drop theproduct or it receives a severe physical shock.If you continue using them under such circumstances, a shortcircuit resulting in fire or electric shock may occur. Pleasecontact your nearest sales representative.CompulsoryBe sure to observe instructions by manufacturers ofpersonal computers and peripherals when installing andusing this product.UnpluggingTurn off the power to the computer and peripheraldevices immediately and unplug them if smoke or heat isgenerated.If you continue using them under such circumstances, a shortcircuit resulting in fire or electric shock may occur. Pleasecontact your nearest sales representative.WLI-CF-S11G.book 3 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual4CAUTIONCompulsoryNever touch this product with wet hands when the powercable of this product is connected to the power outlet. It will cause electric shock.CompulsoryTouch something made of metal (a door knob oraluminum window frame, for example) and release staticelectricity before touching the product to avoid damagecaused by static electricity.Static electricity generated around the human body maydamage this product or delete or damage digital data.CompulsoryFollow the local rules or regulations when disposing ofthis product.Inquire of your local government about the applicable rules orregulations.CompulsoryBe sure to create backup files on other media (floppydisk, MO disk, etc.) for your data on the hard disk.We recommends that you create two backup copies of criticaldata, one before and one after the original data is updated. Datamay be deleted or damaged when• Data may be deleted or damaged when:• Incorrect operation is performed.• Data is affected by static electricity or electrical noise.• Hardware is mechanically damaged or under maintenance.• Your computer is turned on immediately after being turnedoff.• Hardware is damaged in a natural disaster.Note that We shall not be liable for any damages arising fromloss or damage of digital data in any case.WLI-CF-S11G.book 4 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual 5Using this manualThe following describes the notational conventions used in this manual.Please use care for the marks and notations to use this manual effectively.■Editorial marks and notationsCaution mark Describes cautions when handling the product. If these instructionsare not observed, injuries or mechanical damage may occur.Note mark Describes supplementary information or items which should beunderstood when handling the product.Reference mark Indicates the page(s) containing related information.• Descriptions enclosed by square brackets [ ] apply to the name of a menu,button, textbox, or checkbox to be selected during operation.• Descriptions enclosed by double quotation marks " " primarily apply tothe software, dialog box, message, or a title of a section to be referencedduring operation.• As a general rule, this manual primarily refers to the BUFFALO'swireless LAN card as the WLI-CF-S11G, a packet PC or handheld PCwith Windows CE as a Windows CE device, and a personal computerwith Windows Me/98/2000 as a Windows computer.• As a general rule, this manual refers to a Windows CE device and aWindows computer each equipped with the BUFFALO's wireless LANcard as a wireless LAN computer.• This manual clearly distinguishes between a cabled 10BASE-T/100BASE-TX LAN and a non-cabled LAN as followsWired LAN……LAN connected by cablesWireless LAN…LAN using wireless communicationNote that these are not general terms and are used only for descriptions inthis manual.WLI-CF-S11G.book 5 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual6■All rights for this manual are owned by BUFFALO. No part of this manual may betransmitted, reproduced, or revised without permission from BUFFALO.■Product names of other companies used in this manual are trademarks or registeredtrademarks of the respective companies.Trademark symbols , ,  are not indicated in this manual.■Specifications, design, and other descriptions included in this manual are subject tochange without notice.This manual is carefully prepared, however, feel free to contact your nearest salesrepresentative if you have any questions or problems.This product should be used as a general OA device in offices or at home. BUFFALO doesnot accept any liability if the product is used other than as a general OA device.・Do not use this product for any device or system which requires high safety such as amedical device or any system which is directly or indirectly related to maintaininghuman life.・If this product is used for any device or computing system which requires morereliability than general OA devices, please make sure that you take any necessary actionsto ensure safety and prevent system malfunctioning.■Be sure to follow the operation method described in this manual. In particular, never usethis product in such a way as violating the method described as a caution.WLI-CF-S11G.book 6 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual 7Table of ContentsChapter 1 Before Operation1.1 Product Outline..................................................... 101.2 Contents of Package and Component Names ..... 14Chapter 2 Windows CE Settings2.1 Making the Wireless LAN Card Available............. 182.2 Preparing for Connecting to the Network ............. 212.3 Connecting to the Network ................................... 23Chapter 3 Windows Me/98Settings3.1 Making the Wireless LAN Card Available............. 343.2 Preparing for Connecting to the Network ............. 493.3 Connecting to the Network ................................... 62Chapter 4 Windows 2000 Settings4.1 Making the Wireless LAN Card Available............. 724.2 Preparing for Connecting to the Network ............. 854.3 Connecting to the Network ................................... 89Chapter 5 Trouble shooting5.1 Trouble in the Wireless LAN Card Setting............ 965.2 Trouble in Communication With Wireless LAN Computers .......................................................... 105Chapter 6 Glossary6.1 Terms Related to the Network .............................1166.2 Terms in Windows Screens Related to theNetwork .............................................................. 123Chapter 7 Specifications7.1 Product Specifications ........................................ 128WLI-CF-S11G.book 7 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual8MEMOWLI-CF-S11G.book 8 ページ ２００２年３月１日　金曜日　午後６時１６分
■Overview Chapter1Chapte r 4BeforeOperationThis chapter contains the outline of the productand the contents of the package. Be sure toread them so that you can smoothly proceedwith the preparatory operations withouttrouble.1.1 Product Outline■ About wireless LAN card WLI-CF-S11G ....................10 p■ Wireless LAN network configuration ..........................12 p1.2 Contents of Package and Component NamesWLI-CF-S11G.book 9 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual101.1 Product OutlinePlease be aware of the following points before using the wireless LAN cardWLI-CF-S11G.■ About the wireless LAN card WLI-CF-S11GThe wireless LAN card WLI-CF-S11G is installed for use in computersequipped with a Compact Flash slot (type II) or PC card slot (type II).Features• 2.4 GHz low power data communication system (certification not required).• Direct sequence spread spectrum (DS-SS) technology ensures high noise resistance.• IEEE802.11b compliant, with a data rate of 11 Mbps even on a wireless LAN.• Effective range is shown below;11 Mbps transmission: 160 m outdoors (estimated)50 m indoors (1) (estimated)25 m indoors (2) (estimated)2 Mbps transmission: 400 m outdoors (estimated)90 m indoors (1) (estimated)40 m indoors (2) (estimated)1 Mbps transmission: 550 m outdoors (estimated)115 m indoors (1) (estimated)50 m indoors (2) (estimated)※ Indoors (1): .....Office with few obstaclesIndoors (2): .....Office with many obstacles※ The effective range is adversely affected by the operating environment.It may be reduced in the following locations.• Within a reinforced concrete building such as a condo, or a house with a metal frame• Near large metal furnitureWLI-CF-S11G.book 10 ページ ２００２年３月１日　金曜日　午後６時１６分
1Before OperationWLI-CF-S11G User's Manual 11• 40-/128-bit WEP compatible. (For more information, see "About WEP (Wired Equivalent Privacy) - Recommendation of Encryption -" on page 13.)※ When using 128-bit WEP, all access points need to be compatible withthe 128-bit WEP. (40-bit WEP and 128-bit WEP cannot be used at thesame time.)The WLI-CF-S11G card can be used in computers with the compatibleoperating systems listed below.Applicable ComputersPersonal computers equipped with a Compact Flash slot (type II) or PC cardslot (type II) listed below.• Pocket PC • Handheld PC • IBM AT compatible PC (OADG compliant)※ Installation of the card in a PC card slot (type II) requires theBUFFALO's card adapter WLI-CF-OP available separately.• BUFFALO's print server LSP Series and networkdiagnostic tool NetSeeker are not supported. • The Suspend/Resume feature is not supported. • Dual-processor machine is not supported.Operating System※ Windows CE3.0 (Handheld PC 2000, Packet PC), Windows ME/98/2000※ The ACPI feature in Windows Me/98/2000 is not supported.WLI-CF-S11G.book 11 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual12■ Wireless LAN network configurationThe following two methods are available for PC communications with the wirelessLAN card.This product can communicate with BUFFALO's LANproducts, third-party wireless LAN products with Wi-Ficertified, and AirMac(*).※ Communication with AirMac requires BUFFALO'sAirStation.<<Communicating with wireless LAN computers>>You can configure the wireless LAN only network of the wireless LANcomputers with BUFFALO's wireless LAN cards/adapters.Wireless LAN PCWireless LAN PCWireless LAN PCWLI-CF-S11G.book 12 ページ ２００２年３月１日　金曜日　午後６時１６分
1Before OperationWLI-CF-S11G User's Manual 13≪Communicating via AirStation ≫You can connect to the Internet or communicate with computers on thewired LAN via BUFFALO's AirStation.■ WEP (Wired Equivalent Privacy) - Recommendation of EncryptionSince the wireless LAN card communicates using radio waves, radiopackets could be intercepted and analyzed outside. To ensure transmissionsecurity, it is recommended to set a password called 'WEP' in the radiopackets during communication.This card allows two types of WEP; 40-bit WEP and 128-bit WEP. Setting128-bit WEP (13 alphabetic characters or 26 hex digits) assures highersecurity. However, when communicating with a wireless LAN productcompatible only with 40-bit WEP (5 alphabetic characters or 10 hex digits),it is necessary to set the 40-bit WEP in this product.※ For the WEP (encryption) setting in the AirStation, refer to the manualincluded in the AirStation.AirStationWired LAN Wireless LAN PCWLI-CF-S11G.book 13 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User's Manual141.2 Contents of Package and Component NamesThe items listed below are included in the package. Please check thepackage and contact your nearest sales representative if any items aremissing.• Wireless LAN card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• AirStation Driver CD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• WLI-CS-S11G User's Manual (this document) . . . . . . . . . . . . . . . . . . . . . 1• User registration card, warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• Be sure to read any additional information sheets provided in thepackage.Name FunctionPOWER lamp ON (green): During operationACTIVE lamp ON (green): During data send/receiveACTIVE lampPOWER lampWLI-CF-S11G.book 14 ページ ２００２年３月１日　金曜日　午後６時１６分
■Overview Chapter2Chapter 2 WindowsCE SettingsThis chapter describes how to make thesettings for connecting your Windows CEdevice to a wireless LAN.2.1 Making the Wireless LAN Card Available Step 1 Before installing the wireless LAN card ............ 18 pStep 2 Installing the wireless LAN card drivers ............18 pStep 3 Installing the wireless LAN card .........................20 p2.2 Preparing for Connecting to the Network Step 4 Checking the "IP address" ................................. 21 p2.3 Connecting to the Network Step 5 -a Communicating via AirStation .......................... 23 pStep 5 -b Communicating with wireless LAN computers ............................................................ 27 pWLI-CF-S11G.book 15 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User’s Manual16Follow the procedure in the illustration below to connect your Windows CEdevice to a wireless LAN.WindowsCEOperation FlowMaking the wireless LAN card available Preparing for connecting to the networkConnecting to the networkConnect a Windows computer and your Windows CE device via Microsoft Active-Sync.Install the wireless LAN card drivers in the Windows com-puter.Make the settings for access to the network.a. AirStation b. Wireless LAN computersCheck the"IP address."Step 1 Step 2Step 5 -a, bStep 4（from page 21）（from page 18）（from page 23）WLI-CF-S11G.book 16 ページ ２００２年３月１日　金曜日　午後６時１６分
2Windows CE SettingsWLI-CF-S11G User’s Manual 17Install the wireless LAN card in the Windows CE device.To make the Air-Station settings, refer to the AirSta-tion manual.Step 3WLI-CF-S11G.book 17 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User’s Manual182.1 Making the Wireless LAN Card AvailableInstall the wireless LAN card to connect your Windows CE device to awireless LAN.Step 1 Before installing the wireless LAN cardMicrosoft ActiveSyncConnect the Windows CE device and the Windows computer usingMicrosoft ActiveSync so that you can install the wireless LAN card drivers.For how to use ActiveSync, refer to the manual included in the Windows CEdevice.Step 2 Installing the wireless LAN card driversFollow the procedure below to install the wireless LAN card drivers.1Insert the "AirStation Driver CD" into the CD-ROM drive of theWindows computer.When you insert the "AirStation Driver CD" into the CD-ROM drive, the Simple Installation Wizard window mayautomatically appear. In this case, click [Cancel], andthen [Abort], closing the window.2Double-click the [CFS11G] folder in the CD-ROM, and then the[CESETUP] file.3Click [Yes].WLI-CF-S11G.book 18 ページ ２００２年３月１日　金曜日　午後６時１６分
2Windows CE SettingsWLI-CF-S11G User’s Manual 194When the message "Application Downloading Complete"appears, click [OK].The message "Please check your mobile device screen to seeif additional steps are necessary to complete this installation."appears, but you do not need to do so here.5Turn off the Windows CE device.Now you have completed the installation of the wireless LAN card drivers.WLI-CF-S11G.book 19 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User’s Manual20Step 3 Installing the wireless LAN cardInstall the wireless LAN card in the Compact Flash slot (type II) of theWindows CE device.Precautions for installation/removal• Be sure to handle the Windows CE device and its peripheralsin such a way as described in the manual of each unit.• Make sure that the Windows CE device is turned off beforeinstalling/removing the wireless LAN card in/from that device.• Completely remove any dust from the connectors.• Never touch the connector portion of the wireless LAN card.• Use great care for the connector location of the wireless LANcard when installing the card in the Windows CE device. Theconnector may be damaged if it is forced.Installing the wireless LAN card in the Windows CE deviceFollow the instructions in the illustration below when installing the wirelessLAN card in the Windows CE device.WLI-CF-S11G.book 20 ページ ２００２年３月１日　金曜日　午後６時１６分CAUTION STATEMENT: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipmentshould be installed and operated with minmum distance 5cm between the radiator & your body.This transmitter must be co-located or operating in conjunction with any other antenna or transmitter.
2Windows CE SettingsWLI-CF-S11G User’s Manual 212.2 Preparing for Connecting to the NetworkAfter installing the wireless LAN card in the Windows CE device, preparefor connecting to the network.For detailed information, refer to the manual included in the WindowsCE device or open the Windows CE Help.Step 4 Checking the "IP address"1When the wireless LAN card is successfully installed, theWindows CE device is automatically turned on to display thewindow shown below.• When a DHCP server exists within the network (e.g., when theDHCP server function of the AirStation is used), select [Use server-assigned IP address].• To manually set the IP address, select [Use specific IP address].Inquire the IP address, Subnet mask, and Default gateway fromyour network administrator.⇒ Continued on next pageSpecify the [IP address].Ta p [ O K ] .WLI-CF-S11G.book 21 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User’s Manual22• For the IP address setting, see "I don't know how to assign the IPaddress" on page 113 in Chapter 5.If Wiress LAN Card is not operating normally,themessage of the meaning "Input the device driver nameof this card." is displayed.Refer to " Installing the wireless LAN carddrivers" and install driver again.To make the AirStation settingsWith the AirStation manual, make the AirStation settings on a wirelessLAN computer excepting a Windows CE machine.To directly connect to the wireless LANMake the settings on the Windows CE device accordingto on page 23 and subsequent.Step 1Step 2Step 1Step 5WLI-CF-S11G.book 22 ページ ２００２年３月１日　金曜日　午後６時１６分
2Windows CE SettingsWLI-CF-S11G User’s Manual 232.3Connecting to the NetworkUpon completion of necessary settings, you can connect to the network.There are two methods for connecting the Windows CE device to thenetwork as shown below.•Communicating via AirStation -a•Communicating with wireless LAN computers -bStep 5 -a Communicating via AirStationTo make communications using the AirStation, make the settings in theWindow CE device as described below.1Select [Start]-[Settings].2⇒ Continued on next pageStep 1Step 5Step 1Step 5Tap [WLI-CF-S11G].Tap [System].WLI-CF-S11G.book 23 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User’s Manual243The settings are saved with a text typed in the [Profile] field as a name. Select Infrastructure for [Mode]. Input the ESS-ID of the target AirStation to [SSID]. The initial settingof the AirStation ESS-ID shows the last six digits of the MAC addressof the AirStation plus "GROUP" (upper-case). Select Fully Automatic for [Transmit Rate]. Do not put a checkmark for [Power Save Enabled] as it may disablenormal communication.Make a configuration ifnecessary.Tap [Apply].WLI-CF-S11G.book 24 ページ ２００２年３月１日　金曜日　午後６時１６分
2Windows CE SettingsWLI-CF-S11G User’s Manual 2545Tap [Apply].⇒ Continued on next pageTap [Encryption].Select the WEP type (40-bitor 128-bit) if encryption withWEP is used in the network.If the AirStation is still in theinitial state, no encryption isset. Select Disable in thiscase.Select [Create Keys Manually]and input an encryption key tothe Key 1 field.• To use a hexadecimal value, directly input to the Key 1 field. • To use a character string, tap [Alphanumeric] (see below).WLI-CF-S11G.book 25 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User’s Manual266If you cannot communicate with the AirStation, check the ESS-ID andWEP settings of the AirStation, and then repeat from Step 1.Ta p [ Li n k ] .You can check the wireless-side MAC address, currentradio channel, currenttransmission rate, datacommunication status, linkquality, and signal strengthof the connected AirStation. When "Associated" appearsfor the [State], theconnection to the AirStationis successfully complete.WLI-CF-S11G.book 26 ページ ２００２年３月１日　金曜日　午後６時１６分
2Windows CE SettingsWLI-CF-S11G User’s Manual 27Step 5 -b Communicating with wireless LAN computersWhen communicating with wireless LAN computers using MicrosoftActiveSync, it is necessary to make the Windows CE device settings shownbelow.1Select [Start]-[Configure].2⇒ Continued on next pageTap [WLI-CF-S11G].Tap [System].WLI-CF-S11G.book 27 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User’s Manual283The settings are saved with a text typed in the [Profile] field as a name. Select Pseudo AdHoc for [Mode]. You do not have to input data to [SSID]. Select Fully Automatic for [Transmit Rate]. Do not put a checkmark for [Power Save Enabled] as it may disablenormal communication.Select the same channel as the communicated wireless LAN computersfor [AdHoc Channel].Make a configuration ifnecessary.Tap [Apply].WLI-CF-S11G.book 28 ページ ２００２年３月１日　金曜日　午後６時１６分
2Windows CE SettingsWLI-CF-S11G User’s Manual 294《To use a character string for the encryption key》The window shown below appears.1. Input a character string to the [encryption key] field.2. Tap [OK].3. The window in Step 4 appears.5Tap [Apply].⇒ Continued on next pageTap [Encryption].Select the WEP type (40-bitor 128-bit) if encryption withWEP is used in the network.If the AirStation is still in theinitial state, no encryption isset. Select Disable in thiscase.Select [Create Keys Manually]and input an encryption key tothe Key 1 field.• To use a hexadecimal value, directly input to the Key 1 field. • To use a character string, tap [Alphanumeric] (see below).WLI-CF-S11G.book 29 ページ ２００２年３月１日　金曜日　午後６時１６分
WLI-CF-S11G User’s Manual306Now you can communicate with the computers set in the same radiochannel.For the ActiveSync setting, refer to the ActiveSync manual or Help.Ta p [ Li n k ] .You can check the connectionmode (AdHoc), current radiochannel, current transmissionrate, and data communicationstatus. The link quality and signalstrength will not be displayed.Ta p [ O K ] .WLI-CF-S11G.book 30 ページ ２００２年３月１日　金曜日　午後６時１６分

Navigation menu