BUFFALO 09101746-0 AirStation Compact Flash 802.11b Adapter User Manual Part 1

BUFFALO INC. AirStation Compact Flash 802.11b Adapter Part 1

Contents

Part 1

Wireless LAN Card WLI2-CF-S11User's ManualBefore Operation1Windows CE Settings2Windows Me/98 3Windows 2000 Settings4Troubleshooting5Glossary6Specifications7WLI-CF-S11G.book i ページ ２００２年２月２７日　水曜日　午後９時１０分
■ Precautions for radio signals● The wireless LAN card WLI2-CF-S11has been approved for conformityto the engineering standards as the wireless facility for a radio stationwith the low power data communication system based on the WirelessTelegraphy Act. Therefore, use of this LAN card does not require anyradio station license.● Never use the WLI2-CF-S11 near the magnetic field around amicrowave oven or in an area where static electricity and/or radio noise isgenerated. The radio signals may not be normally transmitted in theseareas.* When the WLI2-CF-S11 is used near a wireless printer buffer(BUFFALO's RYP-G or similar products by other manufacturers) thatuse radio signals around 2.4 GHz, the processing speed of bothdevices may be adversely affected.● As the WLI2-CF-S11 has been approved for conformity to theengineering standards, the following may be regarded as unlawful.• Disassembling/remodeling the WLI2-CF-S11• Removing the approval label from the rear of the WLI2-CF-S11● When it is necessary to set a radio channel other than the initial setting inthe WLI2-CF-S11, use the same frequency band as the followingequipment or wireless stations• Industrial, scientific, or medical equipment• Radio station for mobile identification used such as on a manufactureline in a factory①On-premise radio station (requiring a license)②Specific low power radio station (requiring no license)● Operating the WLI2-CF-S11 may cause interference with the aboveequipment or radio stations. Thus, take precautions for the followingpoints1 Before using the WLI2-CF-S11, verify that no on-premise radiostation for mobile identification or no specific low power radiostation is operating near the WLI2-CF-S11.2 If an event of interference should be taken place by the WLI2-CF-S11 with an on-premise radio station for mobile identification,WLI-CF-S11G.book 0 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 1immediately change the frequency for this product to prevent theinterference.3 If you notice any trouble such as an event of interference caused bythe WLI2-CF-S11 with a specific radio station for mobileidentification, contact your nearest sales representative.Operatingfrequency band2.4GHz　Modulation method DS-SSAssumedinterferencedistance40 m or lessFrequencychangeabilityUses the entire bandwidth, and can avoid the"on-premise radio station" and "specific lowerpower radio station" bands.WLI-CF-S11G.book 1 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual2ForewordThank you for purchasing BUFFALO's wireless LAN card WLI2-CF-S11.The WLI2-CF-S11 is installed for wireless LAN communication incomputers equipped with a CompactFlash slot (type II) or PC card slot (typeII).Read this manual carefully before using the wireless LAN card to ensurecorrect operation.■ For your safety, be sure to follow the instructions given below.The following describes the instructions to avoid harming yourself, otherpeople, and properties, and to ensure safe operation of this product. Be sureto read and understand them thoroughly before using this product. Thismanual also contains instructions concerning general operation of thecomputer system to which this product is connected as well as thoseconcerning the product.Please take note that our warranty will not cover any failures and problemsof the computer, any losses and failures of data, or failures and problems ofthis product caused by misuse.Meanings of warning signsWarning Failure to follow the instructions shown with this signmay result in a hazard or serious injury to the user.CAUTION Failure to follow the instructions shown with this signmay result in injury to the user or property damage.WLI-CF-S11G.book 2 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 3■Meanings of symbolsThis indicates warnings and cautions. Specific instructions are givenin or around △. (E.g., Exercise care to avoid an electric shock.)This indicates prohibited matters. Specific instructions are given inor around ○. (E.g., Do not disassemble.)This indicates compulsory rules. Specific instructions are given in oraround ●. (E.g., Disconnect the plug from the receptacle.)WARNINGNo disassemblyDo not disassemble or modify the product.It may cause fire or electric shock.UnpluggingTurn off the power to the computer and peripheraldevices immediately and unplug them if you drop theproduct or it receives a severe physical shock.If you continue using them under such circumstances, a shortcircuit resulting in fire or electric shock may occur. Pleasecontact your nearest sales representative.CompulsoryBe sure to observe instructions by manufacturers ofpersonal computers and peripherals when installing andusing this product.UnpluggingTurn off the power to the computer and peripheraldevices immediately and unplug them if smoke or heat isgenerated.If you continue using them under such circumstances, a shortcircuit resulting in fire or electric shock may occur. Pleasecontact your nearest sales representative.WLI-CF-S11G.book 3 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual4CAUTIONCompulsoryNever touch this product with wet hands when the powercable of this product is connected to the power outlet. It will cause electric shock.CompulsoryTouch something made of metal (a door knob oraluminum window frame, for example) and release staticelectricity before touching the product to avoid damagecaused by static electricity.Static electricity generated around the human body maydamage this product or delete or damage digital data.CompulsoryFollow the local rules or regulations when disposing ofthis product.Inquire of your local government about the applicable rules orregulations.CompulsoryBe sure to create backup files on other media (floppydisk, MO disk, etc.) for your data on the hard disk.We recommends that you create two backup copies of criticaldata, one before and one after the original data is updated. Datamay be deleted or damaged when• Data may be deleted or damaged when:• Incorrect operation is performed.• Data is affected by static electricity or electrical noise.• Hardware is mechanically damaged or under maintenance.• Your computer is turned on immediately after being turnedoff.• Hardware is damaged in a natural disaster.Note that We shall not be liable for any damages arising fromloss or damage of digital data in any case.WLI-CF-S11G.book 4 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11G User's Manual 5Using this manualThe following describes the notational conventions used in this manual.Please use care for the marks and notations to use this manual effectively.■Editorial marks and notationsCaution mark Describes cautions when handling the product. If these instructionsare not observed, injuries or mechanical damage may occur.Note mark Describes supplementary information or items which should beunderstood when handling the product.Reference mark Indicates the page(s) containing related information.• Descriptions enclosed by square brackets [ ] apply to the name of a menu,button, textbox, or checkbox to be selected during operation.• Descriptions enclosed by double quotation marks " " primarily apply tothe software, dialog box, message, or a title of a section to be referencedduring operation.• As a general rule, this manual primarily refers to the BUFFALO'swireless LAN card as the WLI-CF-S11G, a packet PC or handheld PCwith Windows CE as a Windows CE device, and a personal computerwith Windows Me/98/2000 as a Windows computer.• As a general rule, this manual refers to a Windows CE device and aWindows computer each equipped with the BUFFALO's wireless LANcard as a wireless LAN computer.• This manual clearly distinguishes between a cabled 10BASE-T/100BASE-TX LAN and a non-cabled LAN as followsWired LAN……LAN connected by cablesWireless LAN…LAN using wireless communicationNote that these are not general terms and are used only for descriptions inthis manual.WLI-CF-S11G.book 5 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual6■All rights for this manual are owned by BUFFALO. No part of this manual may betransmitted, reproduced, or revised without permission from BUFFALO.■Product names of other companies used in this manual are trademarks or registeredtrademarks of the respective companies.Trademark symbols , ,  are not indicated in this manual.■Specifications, design, and other descriptions included in this manual are subject tochange without notice.This manual is carefully prepared, however, feel free to contact your nearest salesrepresentative if you have any questions or problems.This product should be used as a general OA device in offices or at home. BUFFALO doesnot accept any liability if the product is used other than as a general OA device.・Do not use this product for any device or system which requires high safety such as amedical device or any system which is directly or indirectly related to maintaininghuman life.・If this product is used for any device or computing system which requires morereliability than general OA devices, please make sure that you take any necessary actionsto ensure safety and prevent system malfunctioning.■Be sure to follow the operation method described in this manual. In particular, never usethis product in such a way as violating the method described as a caution.WLI-CF-S11G.book 6 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 7Table of ContentsChapter 1 Before Operation1.1 Product Outline .................................................... 101.2 Contents of Package and Component Names .... 14Chapter 2 Windows CE Settings2.1 Making the Wireless LAN Card Available ............ 182.2 Preparing for Connecting to the Network ............ 212.3 Connecting to the Network .................................. 23Chapter 3 Windows Me/98Settings3.1 Making the Wireless LAN Card Available ............ 343.2 Preparing for Connecting to the Network ............. 523.3 Connecting to the Network .................................. 66Chapter 4 Windows 2000 Settings4.1 Making the Wireless LAN Card Available............ 784.2 Preparing for Connecting to the Network ............ 914.3 Connecting to the Network 95Chapter 5 Trouble shooting5.1 Trouble in the Wireless LAN Card Setting ......... 1025.2 Trouble in Communication With Wireless LAN Computers ..........................................................113Chapter 6 Glossary6.1 Terms Related to the Network ........................... 1266.2 Terms in Windows Screens Related to theNetwork ............................................................. 133Chapter 7 Specifications7.1 Product Specifications ....................................... 138WLI-CF-S11G.book 7 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI-CF-S11G ユーザーズマニュアル8MEMOWLI-CF-S11G.book 8 ページ ２００２年２月２７日　水曜日　午後９時１０分
■Overview Chapter1Chapter 4BeforeOperationThis chapter contains the outline of the productand the contents of the package. Be sure toread them so that you can smoothly proceedwith the preparatory operations withouttrouble.1.1 Product Outline■ About wireless LAN card WLI2-CF-S11 ....... 10 Page■ Wireless LAN network configuration ............. 12 Page1.2 Contents of Package and Component NamesWLI-CF-S11G.book 9 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual101.1 Product OutlinePlease be aware of the following points before using the wireless LAN cardWLI2-CF-S11.■ About the wireless LAN card WLI2-CF-S11The wireless LAN card WLI2-CF-S11 is installed for use in computersequipped with a Compact Flash slot (type II) or PC card slot (type II).Features• 2.4 GHz low power data communication system (certification not required).• Direct sequence spread spectrum (DS-SS) technology ensures high noise resistance.• IEEE802.11b compliant, with a data rate of 11 Mbps even on a wireless LAN.• Effective range is shown below;11 Mbps transmission: 160 m outdoors (estimated)50 m indoors (1) (estimated)25 m indoors (2) (estimated)2 Mbps transmission: 400 m outdoors (estimated)90 m indoors (1) (estimated)40 m indoors (2) (estimated)1 Mbps transmission: 550 m outdoors (estimated)115 m indoors (1) (estimated)50 m indoors (2) (estimated)※ Indoors (1): .....Office with few obstaclesIndoors (2): .....Office with many obstacles※ The effective range is adversely affected by the operating environment.It may be reduced in the following locations.• Within a reinforced concrete building such as a condo, or a house with a metal frame• Near large metal furnitureWLI-CF-S11G.book 10 ページ ２００２年２月２７日　水曜日　午後９時１０分
1WLI2-CF-S11 User's Manual 11• 40-/128-bit WEP compatible. (For more information, see "About WEP (Wired Equivalent Privacy) - Recommendation of Encryption -" on page 13.)※ When using 128-bit WEP, all access points need to be compatible withthe 128-bit WEP. (40-bit WEP and 128-bit WEP cannot be used at thesame time.)The WLI2-CF-S11 card can be used in computers with the compatibleoperating systems listed below.Applicable ComputersPersonal computers equipped with a Compact Flash slot (type II) or PC cardslot (type II) listed below.• Pocket PC • Handheld PC • IBM AT compatible PC (OADG compliant)※ Installation of the card in a PC card slot (type II) requires theBUFFALO's card adapter WLI-CF-OP available separately.• BUFFALO's print server LSP Series and networkdiagnostic tool NetSeeker are not supported. • The Suspend/Resume feature is not supported. • Dual-processor machine is not supported.Operating System※ Windows CE3.0 (Handheld PC 2000, Packet PC), Windows ME/98/2000※ The ACPI feature in Windows Me/98/2000 is not supported.WLI-CF-S11G.book 11 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual12■ Wireless LAN network configurationThe following two methods are available for PC communications with the wirelessLAN card.This product can communicate with BUFFALO's LANproducts, third-party wireless LAN products with Wi-Ficertified, and AirPort(*).※ Communication with AirPort requires BUFFALO'sAirStation.<<Communicating with wireless LAN computers>>You can configure the wireless LAN only network of the wireless LANcomputers with BUFFALO's wireless LAN cards/adapters.Wireless LAN PCWireless LAN PCWireless LAN PCWLI-CF-S11G.book 12 ページ ２００２年２月２７日　水曜日　午後９時１０分
1WLI2-CF-S11 User's Manual 13≪Communicating via AirStation ≫You can connect to the Internet or communicate with computers on thewired LAN via BUFFALO's AirStation.■ WEP (Wired Equivalent Privacy) - Recommendation of EncryptionSince the wireless LAN card communicates using radio waves, radiopackets could be intercepted and analyzed outside. To ensure transmissionsecurity, it is recommended to set a password called 'WEP' in the radiopackets during communication.This card allows two types of WEP; 40-bit WEP and 128-bit WEP. Setting128-bit WEP (13 alphabetic characters or 26 hex digits) assures highersecurity. However, when communicating with a wireless LAN productcompatible only with 40-bit WEP (5 alphabetic characters or 10 hex digits),it is necessary to set the 40-bit WEP in this product.※ For the WEP (encryption) setting in the AirStation, refer to the manualincluded in the AirStation.AirStationWired LAN Wireless LAN PCWLI-CF-S11G.book 13 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual141.2 Contents of Package and Component NamesThe items listed below are included in the package. Please check thepackage and contact your nearest sales representative if any items aremissing.• Wireless LAN card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• AirNavigator CD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• WLI2-CF-S11 User's Manual (this document) . . . . . . . . . . . . . . . . . . . . . 1• User registration card, warranty. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1• • Be sure to read any additional information sheets provided in thepackage.Name FunctionPOWER lamp ON (green): During operationACTIVE lamp ON (green): During data send/receiveACTIVE lampPOWER lampWLI-CF-S11G.book 14 ページ ２００２年２月２７日　水曜日　午後９時１０分
■Overview Chapter2Chapter 2 WindowsCE SettingsThis chapter describes how to make thesettings for connecting your Windows CEdevice to a wireless LAN.2.1 Making the Wireless LAN Card Available Step 1 Before installing the wireless LAN card ......18 pageStep 2 Installing the wireless LAN card drivers ......18 pageStep 3 Installing the wireless LAN card ...................20 page2.2 Preparing for Connecting to the Network Step 4 Checking the "IP address" ...........................21 page2.3 Connecting to the Network Step 5 -a Communicating via AirStation ....................23 pageStep 5 -b Communicating with wireless LAN computers ......................................................27 pageWLI-CF-S11G.book 15 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual16Follow the procedure in the illustration below to connect your Windows CEdevice to a wireless LAN.WindowsCEOperation FlowMaking the wireless LAN card available Preparing for connecting to the networkConnecting to the networkConnect a Windows computer and your Windows CE device via Microsoft Active-Sync.Install the wireless LAN card drivers in the Windows com-puter.Make the settings for access to the network.a. AirStation b. Wireless LAN computersCheck the"IP address."Step 1 Step 2Step 5 -a, bStep 4（from page 21）（from page 18）（from page 23）WLI-CF-S11G.book 16 ページ ２００２年２月２７日　水曜日　午後９時１０分
2WindowsCEWLI2-CF-S11 User's Manual 17Install the wireless LAN card in the Windows CE device.To make the Air-Station settings, refer to the AirSta-tion manual.Step 3WLI-CF-S11G.book 17 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual182.1 Making the Wireless LAN Card AvailableInstall the wireless LAN card to connect your Windows CE device to awireless LAN.Step 1 Before installing the wireless LAN cardMicrosoft ActiveSyncConnect the Windows CE device and the Windows computer usingMicrosoft ActiveSync so that you can install the wireless LAN card drivers.For how to use ActiveSync, refer to the manual included in the Windows CEdevice.Step 2 Installing the wireless LAN card driversFollow the procedure below to install the wireless LAN card drivers.1 Insert the "AirNavigator CD" into the CD-ROM drive of theWindows computer.Be sure to use the latest AirNavigator CD of version3.62 or later. Note that the AirStation may includean AirNavigator CD of earlier version than 3.62.WLI-CF-S11G.book 18 ページ ２００２年２月２７日　水曜日　午後９時１０分
2WindowsCEWLI2-CF-S11 User's Manual 19When you insert the "AirNavigator CD"into the CD-ROM drive, the Simple Installation Wizardwindow may automatically appear. In this case, click [Exit ] to close.2Double-click the [CFS11G] folder in the CD-ROM, and then the[CESETUP] file.34When the message "Application Downloading Complete"appears, click [OK].The message "Please check your mobile device screen to seeif additional steps are necessary to complete this installation."appears, but you do not need to do so here.5Turn off the Windows CE device.Now you have completed the installation of the wireless LAN card drivers.Click [Yes].WLI-CF-S11G.book 19 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual20Step 3 Installing the wireless LAN cardInstall the wireless LAN card in the Compact Flash slot (type II) of theWindows CE device.Precautions for installation/removal• Be sure to handle the Windows CE device and its peripheralsin such a way as described in the manual of each unit.• Make sure that the Windows CE device is turned off beforeinstalling/removing the wireless LAN card in/from that device.• Completely remove any dust from the connectors.• Never touch the connector portion of the wireless LAN card.• Use great care for the connector location of the wireless LANcard when installing the card in the Windows CE device. Theconnector may be damaged if it is forced.Installing the wireless LAN card in the Windows CE deviceFollow the instructions in the illustration below when installing the wirelessLAN card in the Windows CE device.WLI-CF-S11G.book 20 ページ ２００２年２月２７日　水曜日　午後９時１０分
2WindowsCEWLI2-CF-S11 User's Manual 212.2 Preparing for Connecting to the NetworkAfter installing the wireless LAN card in the Windows CE device, preparefor connecting to the network.For detailed information, refer to the manual included in the WindowsCE device or open the Windows CE Help.Step 4 Checking the "IP address"1When the wireless LAN card is successfully installed, theWindows CE device is automatically turned on to display thewindow shown below.• When a DHCP server exists within the network (e.g., when theDHCP server function of the AirStation is used), select [Use server-assigned IP address].• To manually set the IP address, select [Use specific IP address].Inquire the IP address, Subnet mask, and Default gateway fromyour network administrator.⇒ Continued on next pageSpecify the [IP address].Ta p [O K] .WLI-CF-S11G.book 21 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual22• For the IP address setting, see "I don't know how to assign the IPaddress" on page 122 in Chapter 5.If Wiress LAN Card is not operating normally,themessage of the meaning "Input the device driver nameof this card." is displayed.Refer to " Installing the wireless LAN carddrivers" and install driver again.To make the AirStation settingsWith the AirStation manual, make the AirStation settings on a wirelessLAN computer excepting a Windows CE machine.※ When you make the AirStation settings using the "AirNavigator CD," be sure to use the latest version of 3.62 or later.To directly connect to the wireless LANMake the settings on the Windows CE device accordingto on page 23 and subsequent.Step 1Step 2Step 1Step 5WLI-CF-S11G.book 22 ページ ２００２年２月２７日　水曜日　午後９時１０分
2WindowsCEWLI2-CF-S11 User's Manual 232.3Connecting to the NetworkUpon completion of necessary settings, you can connect to the network.There are two methods for connecting the Windows CE device to thenetwork as shown below.•Communicating via AirStation -a•Communicating with wireless LAN computers -bStep 5 -a Communicating via AirStationTo make communications using the AirStation, make the settings in theWindow CE device as described below.1Select [Start]-[Settings].2⇒ Continued on next pageStep 1Step 5Step 1Step 5Tap [WLI-CF-S11G].Tap [System].WLI-CF-S11G.book 23 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual243The settings are saved with a text typed in the [Profile] field as a name. Select Infrastructure for [Mode]. Input the ESS-ID of the target AirStation to [SSID]. The initial settingof the AirStation ESS-ID shows the last six digits of the MAC addressof the AirStation plus "GROUP" (upper-case). Select Fully Automatic for [Transmit Rate]. Do not put a checkmark for [Power Save Enabled] as it may disablenormal communication.Make a configuration ifnecessary.Tap [Apply].WLI-CF-S11G.book 24 ページ ２００２年２月２７日　水曜日　午後９時１０分
2WindowsCEWLI2-CF-S11 User's Manual 254《To use a character string for the encryption key》The window shown below appears.5Tap [Apply].⇒ Continued on next pageTap [Encryption].Select the WEP type (40-bitor 128-bit) if encryption withWEP is used in the network.If the AirStation is still in theinitial state, no encryption isset. Select Disable in thiscase.Select [Create Keys Manually]and input an encryption key tothe Key 1 field.• To use a hexadecimal value, directly input to the Key 1 field. • To use a character string, tap [Alphanumeric] (see below).Ta p [O K] .The window in Step 4 Input a character string tothe [ 暗号化キー ] field.WLI-CF-S11G.book 25 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual266If you cannot communicate with the AirStation, check the ESS-ID andWEP settings of the AirStation, and then repeat from Step 1.Ta p [L in k] .You can check the wireless-side MAC address, currentradio channel, currenttransmission rate, datacommunication status, linkquality, and signal strengthof the connected AirStation. When "Associated" appearsfor the [State], theconnection to the AirStationis successfully complete.WLI-CF-S11G.book 26 ページ ２００２年２月２７日　水曜日　午後９時１０分
2WindowsCEWLI2-CF-S11 User's Manual 27Step 5 -b Communicating with wireless LAN computersWhen communicating with wireless LAN computers using MicrosoftActiveSync, it is necessary to make the Windows CE device settings shownbelow.1Select [Start]-[Configure].2⇒ Continued on next pageTap [WLI-CF-S11G].Tap [System].WLI-CF-S11G.book 27 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual283The settings are saved with a text typed in the [Profile] field as a name. Select Pseudo AdHoc for [Mode]. You do not have to input data to [SSID]. Select Fully Automatic for [Transmit Rate]. Do not put a checkmark for [Power Save Enabled] as it may disablenormal communication.Select the same channel as the communicated wireless LAN computersfor [AdHoc Channel].Make a configuration ifnecessary.Tap [Apply].WLI-CF-S11G.book 28 ページ ２００２年２月２７日　水曜日　午後９時１０分
2WindowsCEWLI2-CF-S11 User's Manual 294《To use a character string for the encryption key》The window shown below appears.1. Input a character string to the [encryption key] field.2. Tap [OK].3. The window in Step 4 appears.5Tap [Apply].⇒ Continued on next pageTap [Encryption].Select the WEP type (40-bitor 128-bit) if encryption withWEP is used in the network.If the AirStation is still in theinitial state, no encryption isset. Select Disable in thiscase.Select [Create Keys Manually]and input an encryption key tothe Key 1 field.• To use a hexadecimal value, directly input to the Key 1 field. • To use a character string, tap [Alphanumeric] (see below).WLI-CF-S11G.book 29 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual306Now you can communicate with the computers set in the same radiochannel.For the ActiveSync setting, refer to the ActiveSync manual or Help.Ta p [L in k] .You can check the connectionmode (AdHoc), current radiochannel, current transmissionrate, and data communicationstatus. The link quality and signalstrength will not be displayed.Ta p [O K] .WLI-CF-S11G.book 30 ページ ２００２年２月２７日　水曜日　午後９時１０分
■OverviewChapter 3Capter 3WindowsMe/98SettingsThis chapter describes how to make thesettings for connecting your Windows Me/98computer to a wireless LAN.3.1 Making the Wireless LAN Card Available Step 1 Before installing the wireless LAN card 34pageStep 2 Installing the wireless LAN card ............40pageStep 3 Installing the wireless LAN carddrivers ......................................................43pageStep 4 Confirming that the installed wireless LAN card is normally operating .............48page3.2 Preparing for Connecting to the Network Step 5 Confirming "TCP/IP" and "Client forMicrosoft Networks" ...............................50pageStep 6 Adding "File and printer sharing forMicrosoft Networks" ...............................57pageStep 7 Checking the computer name andworkgroup name .....................................58pageStep 8 Installing Client Manager .......................59page3.3 Connecting to the Network Step 9 -a Communicating via AirStation ..............63pageStep 9 -b Communicating with wireless LANcomputers ...............................................65pageStep 10 Making your computer shared ..............67pageStep 11 Starting communication .........................68pageWLI-CF-S11G.book 31 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual32Follow the procedure in the illustration below to connect your Windows Me/98 computer to a wireless LAN.WindowsMe/98Operation FlowMaking the wireless LAN card availablePreparing for connecting to the networkConnecting to the networkCheck the configuration of the drives on your Windows computer and confirm that its PC card driver operates normally.Install the wireless LAN card in the Windows comput-er.Make the settings for access to the net-work.a...AirStationb...Wireless LAN computersMake the wireless LAN computer shared.Confirm that the "TCP/IP" and "Client for Micro-soft Networks" are installed.Add "File and print-er sharing for Mi-crosoft Networks."Step 1 Step 2Step 9 -a, b Step 10Step 5 Step 6（from page 66）（from page 34）（from page 52）WLI-CF-S11G.book 32 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI-CF-S11G User's Manual 33Install the wireless LAN card drivers in the Windows comput-er.Confirm that the in-stalled wireless LAN card operates nor-mally.Communicate with other computers on the network.Check the computer name and workgroup name.Install Client Manager for communicating with other wireless LAN computers.To make the AirSta-tion settings, refer to the AirStation manual.Step 3 Step 4Step 11Step 7 Step 8WLI-CF-S11G.book 33 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual343.1 Making the Wireless LAN Card AvailableInstall the wireless LAN card to connect your Windows Me/98 computer toa wireless LAN.Step 1 Before installing the wireless LAN cardChecking the configuration of your drivesFollow the procedure below to check the configuration of the drivers onyour Windows computer in which the wireless LAN card will be installed.The following procedure uses Windows Me for example.1Turn on the computer to boot Windows.2Double-click [My Computer] on Desktop.3These displayed drive names will be necessary in the subse-quent procedures. Be sure to take note of these drive names inthe table on the upper right of the next page.Check the drive nameslisted in the window.Select [View]-[Detail].WLI-CF-S11G.book 34 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 35Drive names on your computerIf your computer has only one PC card slotIf the CD-ROM drive is connected via the PC card to a computer withonly one PC card slot, the CD-ROM drive and this wireless LAN cardcannot be used at the same time. Execute the following steps beforeinstalling the PC card driver.1 Connect the CD-ROM drive to the computer.2 Insert the "AIRCONNECT Series Driver CD" into the CD-ROMdrive.3 Create a new folder (directory) on the hard disk, and copy all filesfrom the CD-ROM to that folder. When you are prompted for the "AIRCONNECT Series Drier CD"during installation, specify the folder to which the files werecopied in the above Step 3.⇒ Continued on next pageDrive Type Icon Drive Name (e.g.)3.5" FDD （A:）HDD (local disk) （C:）CD-ROM （D:）WLI-CF-S11G.book 35 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual36Checking the PC card driverFollow the procedure below to verify that the PC card driver on the computer inwhich the wireless LAN card will be installed is operating normally.1Right-click [My Computer] on Desktop. Click [Properties].2Click the [Device Manager] tab.3Click the "+" mark on the left of [PCMCIA socket].4The displayed PCMCIA socket name varies with the computermodel.Confirm that the "x" mark is notindicated for the icon under[PCMCIA socket].WLI-CF-S11G.book 36 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 37If such an error mark as "!" or "x" is not indicated, the PC card driver isoperating normally.If the icon displayed under [PCMCIA socket] appears withthe ! or x mark, refer to the manual included in the computerand activate the PC card driver.Checking the browser settings (only for using the AirStation)When you use the AirStation, invalidate the dial-up settings and proxysettings under the browser settings. The following procedure uses Internet Explorer 5.0 or later for example.1Select [Start]-[Settings]-[Control Panel].2Double-click [Internet Options].3Double-click the [Connections] tab.4⇒ Continued on next pageWhen the provider informationis listed in the [Dial-upsettings] area, click the ○mark on the left side of [Neverdial a connection] below thearea to put a dot mark.Click [LAN settings] in the"Local Area Network (LAN)settings" area.WLI-CF-S11G.book 37 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual385Confirm the items with a checkmark.For memorandum, put a checkmark for the same items below.□ Automatically detect settings□ Use automatic configuration script□ Use a proxy server□ Bypass proxy server for local addresses6Upon completion of confirming the items with the checkmark,remove the checkmark from all the items.Checking the network adapterConfirm the current settings of the network function.1Select [Start]-[Settings]-[Control Panel].2Double-click [System].3With [View devices by type]selected, click the "+" markon the left side of [Networkadapters]. The currentadapters are listed.Click [Device Manager].WLI-CF-S11G.book 38 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 394Disable a LAN board or card if any name.If there is no LAN board or card name listed, proceed to Step 5.5If any name beginning with "AOL" is found under [DeviceManager]-[Network adapters], disable it in the same manner asStep 4.6Click [OK] to close the [Device Manager].If you have disabled any driver in Steps 4 and/or 5, restartthe computer.Put a checkmark for"Disable in this hardwareprofile."WLI-CF-S11G.book 39 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual40Step 2 Installing the wireless LAN cardThe wireless LAN card can be installed/removed in/from the computerwhich is in the ON state.If your computer is equipped with a power managementfunction that automatically cuts power supply to thecomputer when it is left idle for a certain period, turn thefunction off. The wireless LAN card may be disabled if thepower management function starts.Refer to the manual provided with the computer for detailson the power management function.Precautions for installation/removal• Be sure to handle the computer and its peripherals in such away as described in the manual of each unit.• Completely remove any dust from the connectors.• Never touch the connector portion of the wireless LAN card.• Use great care for the connector location of the wireless LANcard when installing the card in the computer. The connectormay be damaged if it is forced.• The wireless LAN card can be inserted and removed with thecomputer turned on (Hot Swap feature). However, youshould set the wireless LAN card in a safely removable stateon Windows before removing it. See "When removing thewireless LAN card" on page 42.WLI-CF-S11G.book 40 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 41Installing the wireless LAN card in a notebook computerFollow the instructions in the illustration below when installing the wirelessLAN card in a notebook computer.When your computer is equipped with two card slotsAs this wireless LAN card has a protruding section for thebuilt-in antenna, the upper slot may be blocked when thelower one is occupied with this card.Place this wireless LAN card in the upper slot.When inserting the wireless LAN card into the PC card slot on your computer, attach the BUFFALO's PC card adapter WLI-CF-OP available separately.WLI-CF-S11G.book 41 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual42When removing the wireless LAN cardFollow the procedure below to remove the wireless LAN card whenthe computer is running. The following procedure uses Windows MEfor example.1 Click the removal icon in the task tray, and select "StopBUFFALO WLI-CF-S11G Wireless LAN Adapter."※ The removal icon may be [ ] on Windows 98.※ The message displayed when you click the icon varies with theWindows version.※ If you cannot find the icon, see the Windows Help.2 When the message "The 'BUFFALO WLI-CF-S11G Wireless LAN Adapter' device can now be safely removed from the system." is displayed, click [OK].※ The message to be displayed varies with the Windows version.3 Remove the wireless LAN card from the computer.WLI-CF-S11G.book 42 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 43Step 3 Installing the wireless LAN card driversPlease check the configuration of the drives on yourcomputer (page 34) before installing the drivers.In addition, confirm that the PC card driver is normallyoperating on your computer (page 36).The procedure for installing the wireless LAN card drivers varies withWindows Me/98. Use the procedure applicable to your computer as shownbelow.Windows ME user：See <<Windows ME>> below.Windows 98 user：See <<Windows 98>> on page 46.Turn on the computer.《WindowsMe》1The installed wireless LAN card is recognized and the [Add NewHardware Wizard] window appears.If the Wizard window does not appear, see "Thewireless LAN card installation window does notappear." on page 102 in Chapter 5.2 Insert the "AirNavigator CD" into the CD-ROM drive.⇒ Continued on next pageWLI-CF-S11G.book 43 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual44Be sure to use the latest AirNavigator CD of version3.62 or later. Note that the AirStation may includean AirNavigator CD of earlier version than 3.62.When you insert the "AirNavigator CD" into the CD-ROMdrive, the AirNavigator Menu window may automaticallyappear. In this case, click [Exit] to close the window.31. Select [Automatic Search for a better driver (recommended)].2. Click [Next].If the "Copying Files..." window appears, take thefollowing steps before proceeding to Step 4.1. "D:\CFS11G" (when the CD-ROM drive is "D:").2. Click [OK].4When the message "Windows has finished installing the newhardware device." appears, click the [Finish] button.5 Eject the "AirNavigator CD" from the CD-ROM drive.6When the message "Do you want to restart your computer now?"appears, click [Yes].The computer restarts.WLI-CF-S11G.book 44 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 4571. Enter your "User name" and "Password."2. Click [OK].The above window may not appear, but it is not a problem.The password field may be left empty.When you enter a password for the first time, the entered characterstring will be registered as your password.Since the password is case-sensitive, use great care when you enter thepassword.When you click [Cancel], you cannot connect to the network. Be sureto click [OK]. Now you have completed the installation of the wireless LAN card drivers.《Windows98》1The installed wireless LAN card is recognized and the [Add NewHardware Wizard] window appears.Click [Next].If the Wizard window does not appear, see "Thewireless LAN card installation window does notappear." on page 102 in Chapter 5.Proceed to " Confirming that the installed wireless LAN cardis normally operating" on page 50.Step 1Step 4WLI-CF-S11G.book 45 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual4621. Select [Search your best driver for your device (recommended)].2. Click [Next].3 Insert the "AirNavigator CD" into the CD-ROM drive.Be sure to use the latest AirNavigator CD of version3.62 or later. Note that the AirStation may includean AirNavigator CD of earlier version than 3.62.When you insert the "AirNavigator CD" into the CD-ROMdrive, the AirNavigator Menu window may automaticallyappear. In this case, click [Exit] to close the window.41. Select "Specify location..."2. Enter "D:\CFS11G" (when the CD-ROM drive is "D:").3. Click [Next].51. Confirm that "BUFFALO WLI-CF-S11G Wireless LAN Adapter"is displayed.2. Click [Next].6When the message " Please insert the disk labeled 'Windows 98CD-ROM', and then click OK. " appears, take the following stepsbefore proceeding to Step 6.1Insert the Windows 98 CD-ROM into the CD-ROM drive.Click [OK].WLI-CF-S11G.book 46 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 472Enter "D:\WIN98" to the "Copy files from" field (when the CD-ROM drive is "D:").Click [OK].7Click [Finish]8When the message "Do you want to restart your computer now?"appears, click [Yes].The computer restarts.9Enter your "User name" and "Password."Click [OK].The above window may not appear, but it is not a problem.The password field may be left empty.When you enter a password for the first time, the entered characterstring will be registered as your password.Since the password is case-sensitive, use great care when you enter thepassword.When you click [Cancel], you cannot connect to the network. Be sureto click [OK].Now you have completed the installation of the wireless LAN card drivers.Proceed to " Confirming that the installed wireless LAN cardis normally operating" on page 50.Step 1Step 4WLI-CF-S11G.book 47 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual48Step 4Confirming that the installedwireless LAN card is normally operatingUpon completion of the installation of the wireless LAN card drivers,confirm that the installed wireless LAN card is normally operating by usingthe procedure below.1Right-click [My Computer] on Desktop.Click [Properties].2Click the [Device Manager] tab.3Confirm that "BUFFALO WLI-CF-S11G Wireless LAN Adapter" isdisplayed under [Network adapters] without any error mark ("x" or"!") indicated.When "BUFFALO WLI-CF-S11G Wireless LAN Adapter" is displayedwithout any error mark ("x" or "!"), your wireless LAN card is normallyoperating.If no driver name is listed or an error mark ("x" or "!") is indicatedYour installed wireless LAN card is not normally operating in this case.See "I want to uninstall the wireless LAN card" on page 106 in Chapter 5,and then uninstall and re-install the wireless LAN cad drivers.To make the AirStation settingsRefer to the AirStation manual to make the AirStation settings.Step 1Step 4WLI-CF-S11G.book 48 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 493.2 Preparing for Connecting to the NetworkUpon completion of confirming that the installed wireless LAN card isnormally operating, prepare for connecting to the network.This section describes how to make the settings in the following operatingenvironment. Use the settings on the computer to be connected to thenetwork for reference.•OS……………… WindowsMe•Protocol………… TCP/IP• Client…………… Microsoft Network Client• Service………… File and printer sharing for Microsoft NetworksFor detailed information, refer to the manual provided with Windows Me/98 and Help file.Step 5 Confirming "TCP/IP" and "Client forMicrosoft Networks"For example, the procedure below applies to the Windows Me computer.1Start your computer.2Select [Start]-[Settings]-[Control Panel].3Double-click [Network].4Confirm that "TCP/IP" and "Client for Microsoft Networks" aredisplayed in the [The following network components areinstalled:] field of the [Configuration] window.WLI-CF-S11G.book 49 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual50When "TCP/IP" is not displayed, see Caution on page 56 to addthe TCP/IP.When "Client for Microsoft Networks" is not displayed, seeCaution on page 58 to add Microsoft Network Client.⇒ Continued on next page《When only the wireless LAN card is installed》Confirm that"TCP/IP" and"Client for MicrosoftNetworks" are listed.Confirm that"Client for MicrosoftNetworks"is displayed.WLI-CF-S11G.book 50 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 51The following appears in the "The following network components areinstalled:" field. However, this does not imply any problem."TCP/IP->BUFFALO WLI-CF-S11G Wireless LAN Adapter"51. Select "TCP/IP."2. Click [Properties].6《When dial-up adapters and/or other LAN boards are installed》Confirm that "TCP/IP" and"Client for MicrosoftNetworks"are listed.Confirm that "Client forMicrosoft Networks" isdisplayed.Click the "IP Address" tab.Enter the IP address.Click [OK].WLI-CF-S11G.book 51 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual52• When a DHCP server exists within the network (e.g., when theDHCP server function of the AirStation is used), select [Obtain IPAddress Automatically].• To manually set the IP address, select [Specify an IP address].Inquire the IP address and Subnet mask from your networkadministrator.• For the IP address setting, see "I don't know how to assign the IPaddress" on page 122 in Chapter 5.7When the window in Step 5 appears again, click [OK] to close the"Network" window.89Windows Me will restart.Now you have completed the TCP/IP settings on the computer which willuse a wireless LAN.Click [Yes].WLI-CF-S11G.book 52 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 53If "TCP/IP" is not displayed, use the procedure below toadd the TCP/IP.121. Select [Protocol].2. Click [Add].3Click [Add].Select "Microsoft" for[Manufacturers].Click [OK].Select "TCP/IP" for[Network Protocols]. WLI-CF-S11G.book 53 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual544When "Client for Microsoft Networks" is not displayed,use the procedure below to add the Microsoft NetworkClient.1Confirm that the TCP/IPhas been added.Click [Add].WLI-CF-S11G.book 54 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 55231. Select "Microsoft" for [Manufacturers].2. Select "Client for Microsoft Networks" for [Network Clients].3. Click [OK].4Select [Client].Click [Add].Confirm that theMicrosoft Network Clienthas been added.WLI-CF-S11G.book 55 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 56Step 6 Adding "File and printer sharing forMicrosoft Networks"12Click [File and PrintSharing].Click the checkbox to put acheckmark for both "I want tobe able to give others accessto my files." and "I want to beable to allow others to print tomy printer(s)."Click [OK].WLI-CF-S11G.book 56 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 573Step 7 Checking the computer name andworkgroup name1Click the [Identification] tab.Check the [Computer name],[Workgroup],and [Computer Description].Click [OK].It is recommended to use alphanumeric characters for the [Computername] and [Workgroup].If a specific character such as a period (.) is included, thecomputer may fail in connecting to the network.The same workgroup name must be assigned to all thecomputers included in the network.⇒ Continued on next pageConfirm that "File and printersharing for MicrosoftNetworks" has been added.WLI-CF-S11G.book 57 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 58Step 8 Installing Client Manager"Client Manager" is a tool for communicating with wireless LAN computersdirectly or via AirStation. It is necessary to install Client Manager in allwireless LAN computers.Use the procedure below to install Client Manager.1 Insert the "AirNavigato CD" into the CD-ROM drive.Be sure to use the latest AirNavigato CD of version 3.62 orlater. Note that the AirStation may include an AirNavigatorCD of earlier version than 3.62.When you insert the "AirNavigato CD" into the CD-ROMdrive, the AirNavigator menu window may automaticallyappear. In this case, proceed to Step 4.WLI-CF-S11G.book 58 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 592Double-click [My Computer] on Desktop.3Double-click the CD-ROM icon（）41. Select [Install the Client Manager].2. Click [Next].56⇒ Continued on next pageClick [Next].Click [Next].WLI-CF-S11G.book 59 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 60789Click [No] when you do not wish to add Client Manager to theStartup menu.Click [Next].Select "Client Manager"Click [Next].Copying the files required forthe installation will start.Reconfirm the component tobe installed.Click [Yes].Client Manager will beregistered in the Startupmenu.WLI-CF-S11G.book 60 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 6110Now you have completed the Client Manager installation process.To uninstall Client Manager1Select [Start]-[Settings]-[Control Panel].2Double-click "Add/Remove Programs."3Select "Client Manager" and click [Add/Remove].4Select "Remove" and click [Next].5When the message "Do you want to completely remove theselected application and all of its components? " appears, click[OK].6When the "InstallShield Wizard Complete" window opens, click[Finish].Click [Finish].WLI-CF-S11G.book 61 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 623.3 Connecting to the NetworkUpon completion of computer settings, you can connect your computer tothe network. There are two methods for connecting the computer to thenetwork as shown below.•Communicating via AirStation -a•Communicating with wireless LAN computers -bStep 9 -a Communicating via AirStationTo make communications using the AirStation, set the ESS-ID using ClientManager.1Select [Start]-[Programs]-[AirStation Utility]-[Client Manager].If the icon below appears in the task tray in the lower right on thescreen, you can double-click that icon to start Client Manager. or 2Step 1Step 9Step 1Step 9Select [File]-[Manual].WLI-CF-S11G.book 62 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 6331. Select "11Mbps Communication over AirStation" in the"Network Mode" field.2. Enter the AirStation ESS-ID to the "ESS-ID" field.3. Click [OK].The initial setting of the AirStation ESS-ID shows the last six digits ofthe MAC address of the AirStation plus "GROUP" (upper-case).4Enter an "WEP Key" if encryption with WEP is used in the network. Ifthe AirStation is used in the initial state, no encryption is set. Leave thearea empty in this case.5⇒ Continued on next pageClick [OK].AirStation retrieval will bestarted.WLI-CF-S11G.book 63 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 646When the access to the AirStation is successful, the AirStationindication turns from gray to black so that the antenna mark（）appears.After the computer has succeeded in connecting to the AirStation, aslower data rate such as "2Mbps" may be displayed in the "Transferspeed" column. In this case, the correct data rate will appear whenthe practical communication starts.Step 9 -b Communicating with wirelessLAN computersWhen communicating with wireless LAN computers, manually set a radiochannel using Client Manager.1Select [Start]-[Programs]-[AirStation Utility]-[Client Manager].If the icon below appears in the task tray in the lower right on thescreen, you can double-click that icon to start Client Manager. or When this window appears,the access to the AirStationis successful.WLI-CF-S11G.book 64 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 65234Now you have completed the radio channel configuration procedure.Select [File]-[Manual].Select the same channel asthe other computers thatyou wish to communicateClick [OK].Select "Peer to peercommunication" in the"Network Mode" field.Click [OK].Enter an "WEP Key" ifencryption with WEP is usedin the network. If the initialsettings are used, noencryption is set. Leave thearea empty in this case.WLI-CF-S11G.book 65 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 66Step 10 Making your computer sharedUpon completion of wireless LAN channel configuration, make the settingsfor sharing the drives and folders in your computer so that any computer onthe network can use them.The example here describes the procedure for sharing [My Document] inWindows Me.1Double-click [My Computer] on Desktop, and then the C: driveion.23For details on "Share Name," "Comment," "Access Type," and"Passwords," see "Setting window for sharing in Windows Me/98" on page 133 in Chapter 6.Right-click [My Documents],and select [Sharing] fromthe menu.Click［Shared As］.Click [OK].Check or change, ifnecessary, "Share Name,""Comment," "Access Type,"and "Passwords."WLI-CF-S11G.book 66 ページ ２００２年２月２７日　水曜日　午後９時１０分
3Windows Me/98WLI2-CF-S11 User's Manual 674Upon completion of sharing setting, the [My Documents] iconchanges as shown below.Now you have completed the setting for sharing [My Documents].Step 11 Starting communicationUpon completion of setting for sharing the drives and folders, you canaccess a computer on the network.1Double-click [My Network] on Desktop.In Windows 98, double-click the [Network Computer] icon, andproceed to Step 4.2⇒ Continued on next pageDouble-click[Entire Network].WLI-CF-S11G.book 67 ページ ２００２年２月２７日　水曜日　午後９時１０分
WLI2-CF-S11 User's Manual 683Double-click the workgroup name icon.All computers connected on the network are listed.When your target computer is not listed, see "Other computersare not listed (during communication without the AirStation)" onpage 114 in Chapter 5.4Double-click the icon of your target computer.5Double-click your target folder.6All available folders and files in the selected folder are listed sothat you can open, create, or update a file in them.All available folders and files in the selected folder are listed so thatyou can open, create, or update a file in them.WLI-CF-S11G.book 68 ページ ２００２年２月２７日　水曜日　午後９時１０分

Navigation menu