Banner Engineering RM1809 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER User Manual USERS MANUAL

Banner Engineering Corporation FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER USERS MANUAL

Contents

USERS MANUAL

Download: Banner Engineering RM1809 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER User Manual USERS MANUAL
Mirror Download [FCC.gov]Banner Engineering RM1809 FREQUENCY HOPPING SPREAD SPECTRUM TRANSMITTER User Manual USERS MANUAL
Document ID853560
Application IDg4n3sqWL+4v/ekIpsydKMA==
Document DescriptionUSERS MANUAL
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize162.74kB (2034236 bits)
Date Submitted2007-10-11 00:00:00
Date Available2007-10-12 00:00:00
Creation Date2007-04-12 14:39:18
Producing SoftwareAdobe PDF Library 7.0
Document Lastmod2007-04-17 14:00:32
Document TitleUSERS MANUAL
Document CreatorAdobe InDesign CS2 (4.0.4)

SureCross™ DX80 Quick Start Guide
A setup guide for the SureCross™ DX80 wireless systems
Introducing the SureCross™ DX80 Wireless System
The SureCross™ DX80 wireless system provides reliable monitoring without the burden
of wiring or conduit installation, and can operate independently or in conjunction with a
PLC and/or PC software.
The SureCross DX80 network is a deterministic system—the network identifies when
the radio signal is lost and drives relevant outputs to user-defined conditions. Once the
radio signal is reacquired, the network returns to normal operation.
Each wireless system consists of one Gateway and one or more Nodes that ship with
factory predefined inputs and outputs. Devices may be all discrete I/O, mixed discrete
and analog I/O, and FlexPower™.
A Gateway device acts as the master device within each radio network system. The
Gateway initiates communication and reporting with the Nodes.
A radio network contains only one Gateway, but can contain many Nodes. Each Node
device can be connected to a sensor or output device and reports I/O status to the
Gateway.
A Gateway and Node can be arranged to extend the range of the network or to avoid
obstacles in the transmission path. The Gateway receives a transmission from one
Node and forwards it to another Node positioned to avoid the obstacle.
Table of Contents
Overview.................................................1
Features and Components......................2
Menu System..........................................4
QuickStart
Step 1: Set NID & Device Address 6
Step 2: Apply Power (Gateway)......7
Step 3: Apply power (Node)............7
Step 4: Verify Communications.......8
Step 5: Site Survey.........................9
Step 6: Installation........................10
Maintenance/Parts Replacement..........13
Host Network........................................15
Product Dimensions..............................17
Troubleshooting....................................18
Accessories..........................................20
Agency Certifications............................21
FCC Certification..................................22
Host-connected systems can contain up to 15 nodes within a single network and may
be all discrete or a mix of discrete and analog I/O. Host-connected systems allow for
logic and calculations to be applied to the I/O. Inputs from Nodes within the network
are transmitted to the Gateway, which communicates the information to a host device
for processing. While the Gateway is the master device within the radio network, the
Gateway is a slave to the Modbus network.
FlexPower devices allow for a true wireless solution as the Node can be powered
by line power (10 to 30V dc) or battery power (3.6 to 5.5V dc). A SureCross DX81
battery pack and unique power management system runs the Node and a device for
up to five years, depending upon the power requirements of the device. Battery life is
application specific. Contact Banner Engineering’s application engineers for a battery
life calculation for your specific application.
WARNING… Not to be used for personnel protection
Never use these products for personnel protection. Doing so could lead to serious injury or death.
These products do NOT include the self-checking redundant circuitry necessary to allow their use in personnel safety applications.
A failure or malfunction can cause either an energized or de-energized product output condition. Consult your current Banner Safety
Products catalog for safety products that meet OSHA, ANSI, and IEC standards for personnel protection.
Printed in USA
04/07
P/N 128185 Rev B
SureCross™ DX80 Quick Start Guide
DX80 Gateway and Node Front Panel Interface
Rotary Switches: Used to set Network ID & Device Address
1 Rotary Switch 1 (left)
Sets the Network ID (NID) to a hexidecimal value from 0 to F, for a total of 16 Network IDs. A Gateway and its corresponding
Nodes must be assigned the same Network ID.
2 Rotary Switch 2 (right)
On Gateway: Sets the Gateway’s LCD viewing device address. The Gateway is predefined as Device Address 0.
On Node: Sets the Node’s Device Address (hexidecimal 1 to F). Each Node within a network must have a unique Node
Device Address.
Push Buttons: Used to navigate the Gateway and Node menus and program device configurations
3 Push Button 1
Single-click to advance across all top-level DX80 menus.
etc.
Single-click
Button 1
Single-click to move down interactive menus, once a top-level menu is chosen.
4 Push Button 2
Double-click to select a menu and to enter manual scrolling mode.
Double-click to move up one level at a time.
Single-click
Button 1
Double-click
Button 2
Single-click
Button 1
Double-click
Button 2
etc.
6 LED 1 and 2
Provide real-time feedback to the user regarding RF link status, serial communications activity, and the error state.
7 LCD Display
Six-character display provides run mode user information and shows enabled I/O point status. This display allows the user
to conduct a Site Survey (RSSI) and modify other DX80 configuration parameters without the use of a PC or other external
software interfaces. On the Node, after 15 minutes of inactivity, the LCD goes blank. Press any button to refresh the display.
    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
DX80 Gateway and Node Wiring Chamber
NPT Gland, or Plug
1 Port,
If unused, install the provided plug into the 1/2 NPT threaded port. Use PTFE tape if an IP67 seal is required.
2 Housing
The rugged, industrial DX80 housing meets IEC IP67 standards.
3 Mounting Hole, #10/M5 Clearance
Mounting Holes accept metric M5 or UNC/UNF #10 hardware -- DIN rail mount adapter bracket available
4 Wiring Terminal Strip
5 Wiring Terminal
The 16 spring-clip type wiring terminals accept wire sizes: AWG 12-28 or 2.5 mm2
6 Port, PG-7 Gland or Blank
The PG-7 threaded ports can accept provided cable glands or blanks.
7 Ribbon Connector
Ribbon cable connects wiring base to LCD/radio.
8 5-Pin M12 Euro-style quick-disconnect fitting
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    
SureCross™ DX80 Quick Start Guide
SureCross™ DX80 Gateway Setup Menu
When power is applied, the DX80 immediately begins running. The display screen autoscrolls through the *RUN menu and
communication begins between the Gateway and Node(s). Autoscrolling through the *RUN menu is the normal operating mode for all
devices on the wireless network.
From the *RUN Menu (or any menu), single-click button 1 to advance through the top-level menus.
To return to the top level menus and autoscrolling mode, double-click button 2 twice.*** To enter manual scrolling mode, double-click
button 2 at the top level menu. The device autoscrolls through the *RUN, *DINFO, and *FCTRY menus if paused on those menu
headings. If the device is paused on the *SITE, *DVCFG, or *DERR menu options, the display does not autoscroll.
NID XX
NID XX
(DEV)
(DEV)
GATEWY
GATEWY
AUTO
DISPLAY
LOOP
Single-click
Button 1
Single-click
Button 1
(DEV)
GATEWY
(NAME)
GATEWY
I/O XX
I/O XX
KIT
ON/OFF
ON/OFF
XX
(NID)
XX
Single-click
Button 2
(DEV)
GATEWY
(RADIO
MICRO)
V 00.0 A
(BAUD)
XX
(PRTY)
XX
Single-click
Button 2
NOD XX
Single-click
Button 2
AUTO
DISPLAY
LOOP
M XX
R XX
Y XX
G XX
V 00.0 A
Double-click
Button 2
S/N)
(0000)
Single-click
Button 2
EC XX
ADJUST RIGHT
ROTARY SWITCH
TO SURVEY
RESPECTIVE NODE
MICRO)
(DX80
*DERR
NOD XX
(LCD
(SLID)
XX
*DVCFG
Next
Device
(DX80
New Error
Detected
Single-click
Button 2
Single-click Button 1 to advance through menu
CLEAR
DISABL
IGNORE
Single-click
Button 2
Single-click
Button 2
Single-click
Button 2
ERR
ERR
ERASED
DISABL
Single-click
Button 2
Single-click
Button 2
Single-click Button 1 to advance through menu
(NID)**
Network ID
(SLID)
Slave ID
Single-click
Button 2
Single-click
Button 2
ADJUST LEFT
ROTARY SWITCH
TO SET
NETWORK ID
ADJUST ROTARY
SWITCHES
TO SET
SLAVE ID
NEW XX
CUR XX
NEW XX
MODEL)
* ERROR
Single-click
Button 2
Single-click
Button 2
SAVES NEW
VALUES
SAVES NEW
VALUES
(0000-00)
(BAUD)
(PRTY)
Single-click
Button 2
Single-click
Button 2
9600
None
Baud Rate
19200
38400
Parity
Single-click B1
Single-click Single-click
Button 1
Button 1
AUTO
DISPLAY
LOOP
*SITE
Single-click B1
ADJUST RIGHT
ROTARY SWITCH
TO SURVEY
RESPECTIVE NODE
*FCTRY
Double-click Button 2
AUTO
DISPLAY
LOOP
*DINFO
Double-click
Button 2
*RUN
Even
Odd
Single-click
Button 2
Single-click
Button 2
SAVES
DISPLAYED
VALUE
SAVES
DISPLAYED
VALUE
(PROD
DATE)
(00-00)
** The Network ID (NID) can be set at any time from the left rotary switches. Once changed, allow five seconds for the devices to
update to the new NID.
*** At any point in the menu system, double-clicking Button 2 twice returns to the top level menu.
Navigating the menu:
* indicates a top level menu option
( ) indicates a sub-menu item
No characters indicate the value of the previous item
    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
SureCross™ DX80 Node Setup Menu
When power is applied, the DX80 immediately enters *RUN mode. *RUN mode is the normal operating mode for all devices on the
wireless network.
From the *RUN Menu (or any menu), single-click button 1 to advance through the top-level menus.
To return to the top level menus and autoscrolling mode, double-click button 2 twice.*** To enter manual scrolling mode, double-click
button 2 at the top level menu. The device autoscrolls through the *RUN, *DINFO, and *FCTRY menus if paused on those menu
headings. If the device is paused on the *DVCFG or *DERR menu options, the display does not autoscroll.
Single-click
Button 1
*FCTRY
AUTO
DISPLAY
LOOP
Single-click
Button 1
AUTO
DISPLAY
LOOP
(DEV)
(DEV)
(DEV)
NOD XX
NOD XX
NOD XX
(NAME)
(RADIO
I/O XX
NODE XX
MICRO)
KIT
V 00.0 A
(NID)
XX
(LCD
MICRO)
0x0000(2)
(DX80
** The Network ID (NID) and Node Address
(NADR) can be set at any time from the
rotary switches. The left rotary switch sets
the Network ID and the right rotary switch
sets the Node Address.
*** At any point in the menu system,
double-clicking Button 2 twice returns to
the top level menu.
S/N)
0x0000(2)
(DX80
Single-click
Button 2
* ERROR
Single-click
Button 2
**
(NID)
Network ID
XXXXX
*DERR
Single-click
Button 2
Single-click
Button 1
NID XX
ON/OFF
*DVCFG
Single-click
Button 2
Single-click Button 1
NOD XX
** EC XX
New Error
Detected
Single-click
Button 2
IGNORE
Single-click Button 2
AUTO
DISPLAY
LOOP
*DINFO
Double-click Btn 2
*RUN
Press and hold Button 1 from any top level menu to power down the Node.
Press and hold Button 1 from power down mode to enter RUN mode.
Double-click Btn 2
OFF
** LCD will display ‘NO ERR’ if no error is detected.
**
(NADR)
Single-click
Button 1
Node Address
Single-click
Button 2
ADJUST LEFT
ROTARY SWITCH
TO SET
NETWORK ID
ADJUST RIGHT
ROTARY SWITCH
TO SET
NODE ADDRESS
NEW XX
NEW XX
Single-click
Button 2
Single-click
Button 2
SAVES NEW
VALUES
SAVES NEW
VALUES
MODEL)
0x0000(2)
(PROD
DATE)
(00-00)
Navigating the menu:
* indicates a top level menu option
( ) indicates a sub-menu item
No characters indicate the value of the previous item
Node LCD Timeout: After 15 minutes of inactivity, the LCD screen stops displaying information. Press any button to refresh the display if
the Node has entered this energy-saving mode.
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    
SureCross™ DX80 Quick Start Guide
Quick Start: STEP 1 > Set Network ID & Device/Node Address
The wireless RF network is defined by the Network ID (NID)
assigned to the Gateway and its Nodes. Each device within
this common network must have a unique Device Address
assigned.
Network ID (NID)
Device Address
For factory configured kits, the Network ID and Device
Addresses have been assigned. Otherwise, use the Rotary
Switches (shown right) to define both the NID and Device
Address for each device. Follow the steps below to set up
your DX80 network.
Rotary Switches on
Gateway and Node
SET DEVICE ADDRESS
SET NETWORK ID
User Action
Display/Status
Notes
Remove rotary switch access covers.
Turn counterclockwise to remove and clockwise to
tighten
On the Gateway, set the Left Rotary Switch to 1.
The factory default NID setting on all devices is 1. Set
to another Network ID when operating more than one
network in the same area.
On all Nodes (within the same network), set the Left
Rotary Switch to 1.
Assign the same NID to all devices within a single
network (hexidecimal 0-F).
On the Gateway, set the Right Rotary Switch to 0.
A Device Address of 0 on the Gateway will display
settings for the Gateway itself. To view settings for
another device on the network, adjust the Right Rotary
Switch on the Gateway to the respective Device
Address.
On the first Node (Device Address = 1), set the Right
Rotary Switch to 1.
Do not change the Device ID for preconfigured kits as
this would affect the factory mapping of the I/O.
On the second Node (Device Address = 2), set the Right
Rotary Switch to 2.
Continue setting the Device Address for each additional
Node using a unique number (..3,4,5).
Install rotary switch access covers. Please refer to the
installation section for IP67 instructions.
A successful RF link is identified by a blinking green LED
1 on each node.
NID
Multiple Networks
When more than one network is
operating in the same space, assign
a unique Network ID (NID) to each
network (shown right).
GATEWAY
NID
NODE
NODE
NID: 7
Device: 2
NID: 9
Device: 1
GATEWAY
NID
GATEWAY
NODE
NID: 8
Device: 2
NODE
NID: 9
Device: 2
    P/N 128185 Rev B
NODE
NID: 7
Device: 1
NODE
NID: 8
Device: 1
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
Quick Start: STEP 2 > Apply Power, Gateway
To apply power to the Gateway, connect the 10-30V dc cable as shown.
User Action
Display/Status
Apply power...
The LCD display
shows the current I/O
status of the Gateway.
Notes
This reading occurs only when power is
applied to the Gateway.
The Gateway starts in *RUN mode.
Displays current Network ID (NID)
Gateway Pinout Diagram
Device is ...
... Gateway (Device Address = 0)
Brown
Blue
Indicates the current status of the I/O.
The display cycles through each I/O
point of the device, then returns to
*RUN.
10-30V dc Input
dc common
On the Gateway, the other pins are used for
RS485 communications
Quick Start: STEP 3 > Apply Power, Node
To apply power to the Node, connect the 10-30V dc cable or DX81 Battery Module as shown.
Apply power...
The LCD display
shows the current I/O
status of the Node.
This reading occurs only when power
is applied to the Node.
The Node starts in *RUN mode.
Displays current Network ID (NID)
Line Powered Node Pinout Diagram
Device is ...
... Node 1 (Node Address = 1)
Brown
Blue
10-30V dc Input
dc common
Indicates the current status of the I/O.
The display cycles through each I/O
point of the device, then returns to
*RUN.
Note: Terminal block GND = dc common
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    
SureCross™ DX80 Quick Start Guide
Quick Start: STEP 4 > Verify Communications, Gateway
Verify LED 1 is on and green.
Status
LED 1
Power ON
Green ON
System Error
Red Flash
LED 2
—
Red Flash
Modbus Communication Active
—
Yellow Flash
Modbus Communication Error
—
Red Flash
> Verify Communications, Node
Verify LED 1 is flashing Green and LED 2 is off. Until communication is established with
the Gateway, the Node’s LED 2 flashes Red. When communication is established, the
Node’s LED 1 flashes Green.
Status
LED 1
System Error
Red Flash
RF Link Ok
Green Flash (1 per sec)
RF Link Error
—
LED 2
Red Flash (1 per sec)
—
Red Flash (1 per 3 sec)
If testing the Gateway and Node before installation, verify the Gateway and Node are at
least two meters apart or the communications may fail.
    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
Quick Start: STEP 5 > Site Survey (optional)
A site survey analyzes the radio signal between a Gateway and a specified Node and reports the number of data packets missed or
received. Perform the Site Survey before permanently installing your network to ensure reliable communication. Use the Gateway to
perform a site survey analysis.
User Action
Notes
Display/Status
RETURN TO RUN MODE
SURVEY READINGS
SITE SURVEY MENU
Remove Gateway rotary switch access cover.
To check the status of Node 1, change the
Gateway’s right rotary switch setting to 1
The Gateway is now enabled to read the status of
Node 1; the display scrolls through the Node’s I/O
status.
Single-click Gateway push button 1
Device Information menu
Single-click Gateway push button 1
Factory Settings menu
Single-click Gateway push button 1
Site Survey menu
Single-click Gateway push button 2
Site Survey will be conducted with Node 1
Single-click Gateway push button 2
Examine reception readings (M,R,Y,G) of the
Gateway at various locations. Note that the numbers
displayed are a percentage. M displays the percent
of missed packets while R, Y, and G display the
percent of received packets.
The Gateway analyzes the quality of the signal from
the selected Node by counting the number of data
packets it receives from the Node.
M = Percentage of missed packets
R = RED marginal signal
Y = YELLOW good signal
G = GREEN excellent signal
When possible, install all devices in positions that
optimize the percentage of YELLOW and GREEN data
packets received.
Double-click Gateway push button 2
End Site Survey
Change right rotary switch back to 0 (Gateway)
Change the device readings back to the Gateway
Double-click Gateway push button 2
Move back to the top level menu
Single-click Gateway push button 1
Return to RUN mode
Single-click Gateway push button 1
Single-click Gateway push button 1
Install Gateway rotary switch access cover.
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
Refer to the installation instructions to create an IP67
seal.
P/N 128185 Rev B    
SureCross™ DX80 Quick Start Guide
Quick Start: STEP 6 > Installation
Avoid Direct Sunlight
To minimize the damaging effects of
ultra-violet radiation, avoid mounting the
Gateway or Node facing intense direct
sunlight.
Ideal Mounting Conditions
• Mount the DX80 within a protective
enclosure,
• Mount the DX80 under an overhang or
other source of shade,
• Install the DX80 indoors, or
• Face the unit north when installing
outside.
Avoid Collecting Rain
When possible, mount the DX80 where
rain or snow will drain away from the unit.
• Mount the units vertically so that
precipitation, dust, and dirt do not
accumulate on permeable surfaces.
• Avoid mounting the units on flat or
concave surfaces, especially if the
display will be pointing up.
Reduce Chemical Exposure
Before installing the DX80 units in a
chemically harsh environment, contact
Banner for more information regarding the
life-expectancy. Solvents, oxidizing agents,
and other chemicals will damage the DX80.
Minimize Mechanical Stress
While the DX80 is very durable, it is a
sophisticated electronic device that is
sensitive to shock and excessive loading.
• Avoid mounting the units to an object
that may be shifting or vibrating
excessively. High levels of static
force or acceleration may damage the
housing or electronic components.
• Do not subject the DX80 to external
loads. Do not step on the DX80 or use
it as a handgrip.
• Do not allow long lengths of cable to
hang from the DX80 glands. Cabling
heavier than 100 grams should be
supported instead of allowed to hang
from the DX80 housing.
10    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
Installation - Weather-Proofing Glands and Plugs
Watertight Glands and Plugs
If the DX80 is mounted outdoors or will be
exposed to moisture, dirt, or dust, follow
these steps to weatherproof the units.
Watertight Glands
To make the glands watertight:
1. Wrap four to eight passes of
polytetrafluoroethylene (PTFE) tape
around the threads as close as
possible to the hexagonal body of the
gland.
2. Manually thread the gland into the
housing hole. Never apply more than
10 in-lbf of torque to the gland or its
cable clamp nut.
Note, these instructions apply both to the
PG-7 glands and the 1/2” NPT gland.
Rotary Switch Access Cover
Check the rotary switch access cover
o-ring every time the access cover is
removed. Replace the o-ring when it is
damaged, discolored, or showing signs of
wear. The o-ring should be:
• Seated firmly against the threads
without stretching to fit or without
bulging loosely, and
• Pushed against the flanged cover.
When removing or closing the rotary switch
access cover, manually twist the cover
into position. Do not allow cross-threading
between the cover and the DX80 face.
Watertight 1/2” NPT Plug
Seal the 1/2” NPT port if it is not used. To
install a watertight NPT plug:
1. Wrap 12 to 16 passes of PTFE
tape evenly across the length of the
threads.
2. Manually thread the plug into the
housing port until reaching some
resistance.
3. Using a 9/16” crescent wrench, turn
the plug until all the plug’s threads are
engaged by the housing port.
Watertight PG-7 Plug
Seal any unused PG-7 (small) access
holes with one of the supplied black plastic
plugs. To install a watertight PG7 plug:
1. Wrap four to eight passes of PTFE
tape around the plug’s threads, as
close as possible to the flanged
surface.
2. Carefully thread the plastic plug
into the vacant hole in the DX80
housing and tighten using a slotting
screwdriver. Never apply more than
10 in-lbf torque to the plastic plug.
Once the cover is in place and manually
tightened, use a small screwdriver (no
longer than five inches total length) as a
lever to apply enough torque to bring the
rotary switch access cover even with the
DX80 cover surface.
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    11
SureCross™ DX80 Quick Start Guide
Quick Tips
Clear Communication Paths
A wireless network can be hindered by
radio interference and obstructions in the
path between a receiver and transmitter.
To achieve the best radio performance,
carefully consider the installation locations
for the Gateways and Nodes.
Increase Height of DX80 Units
Orient the external antenna vertically for
optimal RF communication. If necessary,
consider changing the height of the DX80
position to improve reception levels.
12    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
Maintenance and Parts Installation
Main Body Gasket
Check the main body gasket every time the
DX80 is opened. Replace the gasket when
it is damaged, discolored, or showing signs
of wear. The gasket must be:
Main Body Gasket
• Fully seated within its channel along
the full length of the perimeter, and
• Positioned straight within the channel
with no twisting, stress, or stretching.
Rotary Switch Access Cover O-Ring
Check the rotary switch access cover
o-ring every time the access cover is
removed. Replace the o-ring when it is
damaged, discolored, or showing signs of
wear. The o-ring should be:
• Seated firmly against the threads
without stretching to fit or without
bulging loosely, and
• Pushed against the flanged cover.
When removing or closing the rotary switch
access cover, manually twist the cover
into position. Do not allow cross-threading
between the cover and the DX80 face.
Rotary Access O-Ring
Once the cover is in place and manually
tightened, use a small screwdriver (no
longer than five inches total length) as a
lever to apply enough torque to bring the
rotary switch access cover even with the
DX80 cover surface.
Replacing O-Rings
Please refer to the list of replacement
parts on page 22 and contact Banner
Engineering with any questions.
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    13
SureCross™ DX80 Quick Start Guide
DX80 Battery Replacement
Battery Replacement
To replace the lithum “D” cell battery in the
DX81 FlexPower battery kit,
1. Remove the four screws mounting the
battery pack face plate to the body.
2. Remove the face plate.
3. Remove the discharged battery and
replace with a new battery. Verify
the battery’s positive and negative
terminals align to the positive and
negative terminals of the battery
holder mounted within the case.
4. After replacing the battery, allow up
to 60 seconds for the device to power
up.
When removing the battery, press the
battery towards the negative terminal
to compress the spring. Pry up on the
battery’s positive end to remove from the
battery holder.
Properly dispose of your used battery by
taking it to a hazardous waste collection
site, an e-waste disposal center, or any
other facility qualified to accept lithium
batteries.
As with all batteries, these are a fire,
explosion, and severe burn hazard. Do not
burn or expose them to high temperatures.
Do not recharge, crush, disassemble, or
expose the contents to water.
14    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
Host Network - Gateway
Setting up the Network and Device IDs, powering up the devices, and conducting the Site Survey for a host-connected network is the
same as for the standard DX80 wireless system. All device I/O for the network is accessed using the host/master device.
To access the Modbus device, you may first need to configure system-level communication parameters on the DX80 Gateway, in
addition to the serial hookups shown below. The following procedure is necessary to change the Gateway Slave ID, Baud Rate, and
Parity.
Parameter
Description
Slave ID (Default = 1)
Defines the slave number (01-99) for the serial Modbus RTU protocol. When operating more than one
network with a Modbus Master device, change the Slave IDs.
Baud Rate (Default = 19200)
Defines communication data rate (19.2, 38.4 or 9.6 kbps) between the Gateway and the Host through the
serial interface.
Parity (Default = None)
Defines serial parity (none, even, or odd) between Gateway and Host.
Gateway (Host-Connected) Pinout Diagram
Brown
White
Blue
Black
Gray
10-30V dc Input
RS485 / D1 / B /+
Ground Input
RS485 / D0 / A / Comms Gnd
Wiring: 5-pin Euro pinouts for 485+, 485- and
Comms ground
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    15
SureCross™ DX80 Quick Start Guide
Host Network - Gateway (con’t)
Setting the Slave ID, Baud Rate, and Parity
Similar to Network ID, the Slave ID, Baud Rate, and Parity parameters can be changed in the Device Configuration (*DVCFG) system
menu option.
Follow the top level system menu through *DVCFG to the Slave ID (SLID) parameter. The LCD displays an alternating current value and
new value for the parameter.
User Action
On the Gateway, single-click button one to move across the top level
menu options to the “Device Configuration” menu
Display/Status
Notes
To navigate to the *DVCFG
(Device Configuration) menu,
see page 6.
SET SLAVE ID
Single-click Gateway push button 2
Single-click Gateway push button 1 to move to the Slave ID field.
Default value is 1
Single-click Gateway push button 2
The new Slave ID is defined
by the current position of the
rotary switches.
Using 0-9 on the left rotary switch and 1-9 on
the right switch, set the rotary switches to the
desired Slave ID
SET BAUD RATE
Single-click Gateway push button 2 to save the new Slave ID.
Select between 01 to 99.
The factory default is set
to 1. Change the Slave ID
when running more than one
network into the Modbus
Master device.
Single-click Gateway push button 1 to move to the next menu option,
the BAUD rate.
Single-click Gateway push button 2 to display the current setting.
Single-click Gateway push button 1 to cycle through the available
options. Stop on the desired setting.
The options are 9600, 19200,
38400. The factory default is
19200.
SET PARITY
Single-click Gateway push button 2 to save the new setting.
Single-click Gateway push button 1 to move to the next field, the
PARITY field.
Single-click Gateway push button 2 to display the current setting.
Single-click Gateway push button 1 to cycle through the available
options. Stop on the desired setting.
The options are NONE,
EVEN, ODD. The factory
default is NONE.
Single-click Gateway push button 2 to save the new setting.
Adjust the left rotary switch back to NID value.*
Adjust the right rotary switch back to zero.
Double-click Gateway push button 2 to return to the Device
Configuration (*DVCFG) menu.
Click Gateway push button 1 until reaching the *RUN menu option.
* To avoid losing the network connection between the Gateway and Nodes, reset the rotary switches back to their appropriate values before leaving the
*DVCFG sub-menus. If the Gateway and Nodes lose their connection, the network may take up to 20 seconds to re-synchronize.
16    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
DX80 Gateway and Node Dimensions
65.0 mm
(2.56")
22.2 mm
(.875")
7.9 mm
(0.31")
30.65 mm
(1.21")
65.0 mm
(2.56")
19 mm
(0.75")
80.3 mm
(3.16")
127 mm
(5")
7.65 mm
(0.30")
60 mm
(2.36")
14.67 mm
(0.578")
80.8 mm
(3.18")
120 mm
(4.72")
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    17
SureCross™ DX80 Quick Start Guide
Troubleshooting
RF Link Time-Out and Recovery
The SureCross™ DX80 wireless devices employ a deterministic link time-out method to address RF link interruption or failure. As
soon as a specific Node/Gateway RF link fails, all pertinent wired outputs are de-energized until the link is recovered (see component
data sheet for more information.) Through this process, users of Banner wireless networks can be assured that disruptions in the
communications link will result in predictable system behavior.
The link time-out feature uses a fully-acknowledged polling method to determine the RF link status of each Node on the network. If after
a specified number of sequential polling cycles the Node does not acknowledge a message, the Gateway considers the link with the
Node timed out. LCD displays on both the Node and Gateway show *ERROR. Following a time-out, the Node de-energizes outputs and
the Gateway sets all outputs linked to the Node in question to a de-energized state. Inputs from the Nodes are mapped to outputs on
the Gateway and are suspended during a link timeout.
Once a link has failed, the Gateway must receive a specified number of good RF communications packets from the Node in question
before the link is reinstated. Outputs are restored to current values when the link is recovered.
For information regarding Host-connected systems and link time-out and recover, please refer to Banner’s DX80 and Modbus Guide.
Link between Gateway and Node 1 timed out.
Link between Gateway and Node 1 recovered.
18    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
Troubleshooting (con’t)
A wireless network can be hindered by radio interference and by obstructions in the path of the receiver and transmitter. To achieve the best radio
performance possible, carefully consider the installation locations for Gateways and Nodes. The need for a clear path increases as the transmission
distance increases. Use Site Survey (RSSI) to confirm signal quality before fixing devices for permanent installation.
Problem Description
Possible Solutions
Basic power–up issues
No LEDs, No LCD
display
• DX80 devices should immediately display ‘POWER’ on the LCD for the first 5-10 seconds after power is applied.
For the Gateway, LED 1 will always be green when power is connected. The Node devices will flash a red LED 2
every three seconds or a green LED 1 every second depending upon the RF Link status.
• Battery powered devices can be put into a power-down mode using button 1 on the front panel. To put a battery
device into power-down mode, hold button 1 for three to five seconds. To make a battery device come out of
power-down mode, hold button 1 for three to five seconds.
• Recheck the power connections and power requirements. Line powered devices require 10 to 30V dc. The DX81
Battery Module provides 3.6V dc.
• After replacing the battery, allow up to 60 seconds for the device to power up.
Node flashes the red
LED (no sync)
• There are two things that MUST be set on every Node device to make it synchronize with the Gateway device:
1) The Network ID on the Node must match the Gateway Network ID. (0-15)
2) Each node within that network must have the Device ID rotary switch set to a unique number (1-15). Refer to
“Getting Started – Multiple Networks, Setting Network ID”
• If the Gateway and Node are less than two meters apart, the devices may not communicate properly (radios may
saturate).
• The Gateway and Node may be too far apart to achieve sync – consult factory for options.
• A qualified antenna should be mounted on both the Gateway and Node devices.
• After any system parameter changes, cycle power to cause the devices to resync with the network.
• If a Node device loses synchronization with the network, it is programmed to try to acquire sync for five seconds,
then sleep for 15 seconds. Synchronizing may require up to 20 seconds.
• Recycle power on the Gateway and Node devices.
DX80 devices will not synchronize
Site survey (RSSI) returns > 30 MISSED packets
Marginal Site Survey
(RSSI) results
If the distance between devices is greater than about 5,000 meters (3 miles) line-of-sight *OR* objects, such as
trees or man-made obstructions, interfere with the path, and the MISSED packet count exceeds 30 per 100 packets,
consider the following steps:
• Raise the DX80 units to a higher elevation – either by physically moving the devices or installing the antenna(s)
remotely at a higher position.
• Use high-gain antenna(s) such as Yagi and/or Omni (see Accessories).
• Decrease the distance between devices.
DX80 Gateway will not talk with the host system
No communications
with the DX80 Gateway
using RS485
• Default communications parameters for the RS485 are: 1 start bit, 8 data bits, no parity, 1 stop bit and 19.2k baud.
The DX80 Gateway uses Modbus RTU protocol for all communications. The supported Modbus function codes are
3, 6, and 16.
• Make sure the DX80 model supports RS485 serial communications.
• Make sure the Slave ID is set properly for the bus environment. Factory default Slave ID = 1.
• Factory default for the Modbus timeout is set to four seconds.
• RS485 termination or biasing is not supplied on the DX80 Gateway and should be provided externally to the DX80.
(Termination is not required by the DX80 Gateway, proper biasing of the serial lines is required.)
DX80 Display shows
*ERROR
• The Gateway utilizes fully-acknowledged polling to ensure each Node RF link is robust. Consequently, if after
a prescribed number of sequential polling cycles are not acknowledged by a Node, the Gateway considers the
particular link with that Node to be timed out. All outputs on the Node in question will be set to “OFF” (discrete) or
“0” (analog, regardless of type).
• If the Node’s RF link is recovered and the Gateway can determine that enough acknowledged polling messages
have been accumulated, then the link is reinstated and outputs are restored to the current values.
RF link time-out and recovery
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    19
SureCross™ DX80 Quick Start Guide
Troubleshooting (con’t)
Problem Description
Possible Solutions
I/O functionality
• Use manual scrolling mode within *RUN to freeze the I/O status on the LCD display for the device in question.
Verify that when the input device changes state or changes value, the LCD mirrors the behavior.
• Also verify that the LCD on the output side mirrors the linked input’s behavior. If the input device state, LCD
on origination DX80, and LCD on destination DX80 all behave exactly the same, there may be a wiring issue
or an interfacing problem. Consult factory.
Particular inputs and/or
outputs are not working
Accessories and Replacement Parts - 900 MHz and 2.4 GHz
Model Number
Description
Antennas
Banner offers a range of omni-directional and directional (Yagi) antennas for use with the SureCross™ DX80
wireless network. For more information on antenna specifications and the options available for your system, please
contact the applications engineers at Banner Engineering Corp.
O-Rings
BWA-ORING-001
O-Ring, Rotary Access Cover, PG21
BWA-GASKET-001
O-Ring, Body Gasket
BWA-CLRCOVER-001
Rotary Access Cover, Clear Plastic
BWA-HW-001
Mounting Hardware, DX80
BWA-HW-002
Access Hardware (Plugs, Glands), DX80
SMBDX80DIN
Bracket Assembly, DIN Rail, for DX80
BWA-HW-003
Tape, PFTE Sealant
BWA-HW-004
Screws, Cover Mount, #8-32 x 3/4, 18-8 SS
DX81
Battery Pack Kit, DX81, with mounting hardware
DX121
Battery Pack Kit, DX121, 6 cells
BWA-BATT-001
Replacement Battery, 3.6V, “D” Lithium Cell
SPS101Q
DC Power Supply, 120mA, 12-30V dc, 5-pin Euro
SPS101QP
DC Power Supply, 120mA, 12-30V dc, 5-pin Euro, pigtail
PS24W
DC Power Supply, 500mA, 24V dc
EZAC-E-QE5
DC Power Supply, 700mA, 24V dc, 5-pin Euro QD
EZAC-E-QE5-QS5
DC Power Supply, 700mA, 24V dc, 5-pin M12 Euro QD
MQDC1-506 2M
Cord Set, 2 Meter, 5-pin, 5-conductor, MQDC1-506 2M
MQDC1-506.5
Cord Set, 0.5 Meter, 5-pin, 5-conductor, MQDC1-506.5
BWA-RIBBON-001
Ribbon Cable, 20 pin DBL socket
BWC-LFNMN
Lightning Suppressor, 900 MHz, 2.4 GHz
Hardware
Power
Cabling
There is a wide range of antenna cabling available. Please contact Banner Engineering Corp for more information
or for specific cable lengths and connectors.
20    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
Agency Certifications
Industry Canada
This Class A digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation
is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouiller du Canada. Le present
appareil numérique n’emet pas de bruits radioélectriques dépassant les limites applicables aux appareils numeriques de le Classe A
préscrites dans le Reglement sur le brouillage radioélectrique édits par le ministere des Communications du Canada.
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    21
SureCross™ DX80 Quick Start Guide
FCC Certification - 900 MHz
FCC Certification
The DX80 Module complies with Part 15 of the FCC rules and regulations.
FCC ID: TGUDX80 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
FCC Notices
IMPORTANT: The DX80 Modules have been certified by the FCC for use with other products without any further certification (as per
FCC section 2.1091). Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate
the equipment.
IMPORTANT: The DX80 Modules have been certified for fixed base station and mobile applications. If modules will be used for portable
applications, the device must undergo SAR testing.
IMPORTANT: If integrated into another product, the FCC ID label must be visible through a window on the final device or it must be
visible when an access panel, door, or cover is easily removed. If not, a second label must be placed on the outside of the final device
that contains the following text: Contains FCC ID: TGUDX80.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna,
Increase the separation between the equipment and receiving module,
Connect the equipment into an outlet on a circuit different from that to which the receiving module is connected, and/or
Consult the dealer or an experienced radio/TV technician for help.
Antenna Warning WARNING: This device has been tested with Reverse Polarity SMA connectors with the antennas listed in Table 1
Appendix A. When integrated into OEM products, fixed antennas require installation preventing end-users from replacing them with nonapproved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203 (unique antenna connectors)
and Section 15.247 (emissions).
FCC-Approved Antennas
WARNING: This equipment is approved only for mobile and base station transmitting devices. Antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
DX80 Module may be used only with Approved Antennas that have been tested with this module.
Part Number
Antenna Type
Maximum Gain
Integral antenna
Unity gain
BWA-9O1-x
Omni, 1/4 wave dipole
≤2 dBi
BWA-9O2-C
Omni, 1/2 wave dipole, Swivel
≤2 dBi
BWA-9O6-A
Omni Wideband, Fiberglass
Radome
≤8.2 dBi
BWA-9O5-B
Omni Base Whip
≤7.2 dBi
BWA-9Y10-A
Yagi
≤10 dBi
—
Table 1. Type certified Antenna
22    P/N 128185 Rev B
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
SureCross™ DX80 Quick Start Guide
FCC Certification - 2.4 GHz
FCC Certification
The DX80 Module complies with Part 15 of the FCC rules and regulations.
FCC ID: UE300DX80-2400 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that
may cause undesired operation.
FCC Notices
IMPORTANT: The DX80 Modules have been certified by the FCC for use with other products without any further certification (as per
FCC section 2.1091). Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate
the equipment.
IMPORTANT: The DX80 Modules have been certified for fixed base station and mobile applications. If modules will be used for portable
applications, the device must undergo SAR testing.
IMPORTANT: If integrated into another product, the FCC ID label must be visible through a window on the final device or it must be
visible when an access panel, door, or cover is easily removed. If not, a second label must be placed on the outside of the final device
that contains the following text: Contains FCC ID: UE300DX80-2400.
Note
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna,
Increase the separation between the equipment and receiving module,
Connect the equipment into an outlet on a circuit different from that to which the receiving module is connected, and/or
Consult the dealer or an experienced radio/TV technician for help.
Antenna Warning WARNING: This device has been tested with Reverse Polarity SMA connectors with the antennas listed in Table 1
Appendix A. When integrated into OEM products, fixed antennas require installation preventing end-users from replacing them with nonapproved antennas. Antennas not listed in the tables must be tested to comply with FCC Section 15.203 (unique antenna connectors)
and Section 15.247 (emissions).
FCC-Approved Antennas
WARNING: This equipment is approved only for mobile and base station transmitting devices. Antenna(s) used for this transmitter must
be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
DX80 Module may be used only with Approved Antennas that have been tested with this module.
Part Number
Antenna Type
Maximum Gain
Integral antenna
Unity gain
BWA-2O2-C
Omni, 1/2 wave dipole, Swivel
≤2 dBi
BWA-2O5-C
Omni, Collinear, Swivel
≤5 dBi
BWA-2O7-C
Omni, Coaxial Sleeve, Swivel
≤7 dBi
—
Table 1. Type certified Antenna
Banner Engineering Corp. • Minneapolis, MN U.S.A.
www.bannerengineering.com • Tel: 763.544.3164
P/N 128185 Rev B    23
CAUTION . . .
Make no modifications
to this product.
Any modifications to this product not
expressly approved by Banner Engineering
could void the user’s authority to operate
the product. Contact the Factory for more
information.
All specifications published in this document are subject to change. Banner reserves the right
to modify the specifications of products, prior to their order, without notice.
WARRANTY: Banner Engineering Corp. warrants its products to be free from defects for
one year. Banner Engineering Corp. will repair or replace, free of charge, any product of its
manufacture found to be defective at the time it is returned to the factory during the warranty
period. This warranty does not cover damage or liability for the improper application of
Banner products. This warranty is in lieu of any other warranty either expressed or implied.
P/N 128185 Rev B
Banner Engineering Corp., 9714 Tenth Ave. No., Minneapolis, MN USA 55441 • Phone: 763.544.3164 • www.bannerengineering.com • Email: sensors@bannerengineering.com

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Copy, Annotate, Fill forms, Extract, Print high-res
Page Count                      : 24
XMP Toolkit                     : XMP toolkit 2.9.1-14, framework 1.6
About                           : uuid:1e107b2c-79dc-46e3-ae5a-b81385bbf9bf
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Create Date                     : 2007:04:12 14:39:18-05:00
Modify Date                     : 2007:04:17 14:00:32-05:00
Metadata Date                   : 2007:04:17 14:00:32-05:00
Creator Tool                    : Adobe InDesign CS2 (4.0.4)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 11107 bytes, use -b option to extract)
Version ID                      : 1
Instance ID                     : uuid:f6fb49fd-aee7-4605-8c05-b708d121961f
Rendition Class                 : proof:pdf
Document ID                     : adobe:docid:indd:d2d9568e-e82b-11db-bb2e-bbdb1799d6eb
Derived From Instance ID        : d2d9568d-e82b-11db-bb2e-bbdb1799d6eb
Derived From Document ID        : adobe:docid:indd:6fd40f4d-2650-11db-9a2a-bcc5f8c244ea
Derived From Version ID         : 1
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00
Manifest Placed Y Resolution    : 72.00, 72.00, 300.00, 72.00, 72.00, 72.00, 72.00, 72.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 300.00, 72.00, 72.00, 72.00
Manifest Placed Resolution Unit : Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:a9ceb44a-a7bd-4028-8d65-c8a333291232, uuid:0AF3BC927FE7DB11B22DE1AC89169639, uuid:d0b470f3-0f88-4055-9d1a-8c3ce80e7685, uuid:8bd85658-ad21-44f3-8306-b84b6799b509, uuid:5c8a337d-2cb1-4f83-a3ea-cfbe165ac6d2, uuid:8494366c-d3de-414c-a679-36019b8c60a9, uuid:0046ffd4-4233-410f-96d6-05dba0961881, uuid:a801a6b2-4459-452b-b20a-1aa52edeadc3, uuid:B9351B2D94F5DA118D069434A1AE4FE6, uuid:96CA85DD752CDB11A136B8FDE7368E1B, uuid:96CA85DD752CDB11A136B8FDE7368E1B, uuid:065F4224C823DB11A1B2D5D04838B582, uuid:EC15A5C72923DB11B879830293AB6491, uuid:98CA85DD752CDB11A136B8FDE7368E1B, uuid:B9351B2D94F5DA118D069434A1AE4FE6, uuid:73B849AAA22CDB1188E1DBCC952B6E84, uuid:0bb9180b-dbe7-4af8-b375-9e6af4da25f7, uuid:148F23D94C26DB11B7A9FB303E676C3F, uuid:118F23D94C26DB11B7A9FB303E676C3F, uuid:86D3A0164D26DB11B7A9FB303E676C3F, uuid:8CD3A0164D26DB11B7A9FB303E676C3F, uuid:8AD3A0164D26DB11B7A9FB303E676C3F, uuid:88D3A0164D26DB11B7A9FB303E676C3F, uuid:168F23D94C26DB11B7A9FB303E676C3F, uuid:04D90C384D26DB11B7A9FB303E676C3F, uuid:02D90C384D26DB11B7A9FB303E676C3F, uuid:575D926C4D26DB11B7A9FB303E676C3F, uuid:5B5D926C4D26DB11B7A9FB303E676C3F, uuid:555D926C4D26DB11B7A9FB303E676C3F, uuid:595D926C4D26DB11B7A9FB303E676C3F, uuid:06D90C384D26DB11B7A9FB303E676C3F, uuid:BA63C5919AD0DB119A67F03A96C0B626, uuid:BA63C5919AD0DB119A67F03A96C0B626, uuid:8431ECC94526DB11B7A9FB303E676C3F, uuid:8131ECC94526DB11B7A9FB303E676C3F, uuid:008C95F44BFADA11B295A6CFA95EAEFC, uuid:048C95F44BFADA11B295A6CFA95EAEFC, uuid:283299A388F5DA118D069434A1AE4FE6, uuid:243299A388F5DA118D069434A1AE4FE6, uuid:008C95F44BFADA11B295A6CFA95EAEFC, uuid:ACE5905991F5DA118D069434A1AE4FE6, uuid:A6E5905991F5DA118D069434A1AE4FE6, uuid:A8E5905991F5DA118D069434A1AE4FE6, uuid:AAE5905991F5DA118D069434A1AE4FE6, uuid:008C95F44BFADA11B295A6CFA95EAEFC, uuid:028C95F44BFADA11B295A6CFA95EAEFC, uuid:243299A388F5DA118D069434A1AE4FE6, uuid:AEE5905991F5DA118D069434A1AE4FE6, uuid:49D35DF391F5DA118D069434A1AE4FE6, uuid:F53C597836FADA11B295A6CFA95EAEFC, uuid:B9351B2D94F5DA118D069434A1AE4FE6, uuid:B9351B2D94F5DA118D069434A1AE4FE6, uuid:32739b72-fd13-4c1a-91dc-f7c5f8617447, uuid:185F57F6958BDB118BA590B956C4465E, uuid:84602BF9F1F7DA11929687F6F01A4FCB, uuid:A1EF7794FBF7DA11929687F6F01A4FCB, uuid:1DEEE81CFE89DB11A823D56643E613AC, uuid:97155451B7D7DB11A6B3DF6C69ACD4DA, uuid:BA63C5919AD0DB119A67F03A96C0B626, uuid:AEE5905991F5DA118D069434A1AE4FE6, uuid:F93C597836FADA11B295A6CFA95EAEFC, uuid:1E15E7AEB0FBDA11A58CE92852C2FB31, uuid:BA3FCE418107DB11814DB238FB908BC5, uuid:F73C597836FADA11B295A6CFA95EAEFC, uuid:1E15E7AEB0FBDA11A58CE92852C2FB31, uuid:2415E7AEB0FBDA11A58CE92852C2FB31, uuid:2615E7AEB0FBDA11A58CE92852C2FB31, uuid:2415E7AEB0FBDA11A58CE92852C2FB31, uuid:81EB7CEFB1FBDA11A58CE92852C2FB31, uuid:83EB7CEFB1FBDA11A58CE92852C2FB31, uuid:81EB7CEFB1FBDA11A58CE92852C2FB31, uuid:AEE5905991F5DA118D069434A1AE4FE6, uuid:F53C597836FADA11B295A6CFA95EAEFC, uuid:A613561EF1F7DA11929687F6F01A4FCB, uuid:E815A5C72923DB11B879830293AB6491, uuid:A613561EF1F7DA11929687F6F01A4FCB, uuid:A613561EF1F7DA11929687F6F01A4FCB, uuid:B83FCE418107DB11814DB238FB908BC5, uuid:E615A5C72923DB11B879830293AB6491, uuid:B83FCE418107DB11814DB238FB908BC5, uuid:11105cbf-b82f-4fdf-8a93-6d6f8aee776c, uuid:e51a074c-825b-4cb1-aba0-fb5df22285f0
Manifest Reference Document ID  : uuid:27FBEF4DA2F1DA11AD6DF69FF4F096E5, uuid:36e1fbd6-462f-11da-b4e4-0030657b8b80, uuid:29C2D495C3D7DB11841585E0D65E51F0, uuid:C87B06D50774DB11B972932CCD53F915, uuid:CF7B06D50774DB11B972932CCD53F915, uuid:55FF9CE39FE6DB11AE89B0900394EFF0, uuid:177A5AA9BAE6DB11AE89B0900394EFF0, uuid:FCED721A8F00DB1193BDC435714CD9B4, uuid:FEED721A8F00DB1193BDC435714CD9B4, uuid:B8351B2D94F5DA118D069434A1AE4FE6, uuid:95CA85DD752CDB11A136B8FDE7368E1B, uuid:95CA85DD752CDB11A136B8FDE7368E1B, uuid:055F4224C823DB11A1B2D5D04838B582, uuid:EB15A5C72923DB11B879830293AB6491, uuid:97CA85DD752CDB11A136B8FDE7368E1B, uuid:B8351B2D94F5DA118D069434A1AE4FE6, uuid:F02A9F33A22CDB1188E1DBCC952B6E84, uuid:3F9E272F3302DB11BC7CB0A65FC83949, uuid:97B6AFCF15F7DA1183C18FB8A2ADCF8D, uuid:058C95F44BFADA11B295A6CFA95EAEFC, uuid:BB88903C6F22DB1199A0B715CDA9C4AA, uuid:9BB6AFCF15F7DA1183C18FB8A2ADCF8D, uuid:9DB6AFCF15F7DA1183C18FB8A2ADCF8D, uuid:9FB6AFCF15F7DA1183C18FB8A2ADCF8D, uuid:8B01CD9817F7DA1183C18FB8A2ADCF8D, uuid:8D01CD9817F7DA1183C18FB8A2ADCF8D, uuid:078C95F44BFADA11B295A6CFA95EAEFC, uuid:BD88903C6F22DB1199A0B715CDA9C4AA, uuid:9101CD9817F7DA1183C18FB8A2ADCF8D, uuid:098C95F44BFADA11B295A6CFA95EAEFC, uuid:9501CD9817F7DA1183C18FB8A2ADCF8D, uuid:25EAF8A818F7DA1183C18FB8A2ADCF8D, uuid:A21FAE3C9AD0DB119A67F03A96C0B626, uuid:A21FAE3C9AD0DB119A67F03A96C0B626, uuid:39C4884C68F7DA1188679A5CF23F50CD, uuid:566106EA68F7DA1188679A5CF23F50CD, uuid:FF8B95F44BFADA11B295A6CFA95EAEFC, uuid:038C95F44BFADA11B295A6CFA95EAEFC, uuid:273299A388F5DA118D069434A1AE4FE6, uuid:233299A388F5DA118D069434A1AE4FE6, uuid:FF8B95F44BFADA11B295A6CFA95EAEFC, uuid:ABE5905991F5DA118D069434A1AE4FE6, uuid:A5E5905991F5DA118D069434A1AE4FE6, uuid:A7E5905991F5DA118D069434A1AE4FE6, uuid:A9E5905991F5DA118D069434A1AE4FE6, uuid:FF8B95F44BFADA11B295A6CFA95EAEFC, uuid:018C95F44BFADA11B295A6CFA95EAEFC, uuid:233299A388F5DA118D069434A1AE4FE6, uuid:ADE5905991F5DA118D069434A1AE4FE6, uuid:AFE5905991F5DA118D069434A1AE4FE6, uuid:F43C597836FADA11B295A6CFA95EAEFC, uuid:B8351B2D94F5DA118D069434A1AE4FE6, uuid:B8351B2D94F5DA118D069434A1AE4FE6, uuid:A9837FF74985DB118260ABBF9B5228FD, uuid:432FBD07BB8ADB11AAD8C00C4E23D11E, uuid:83602BF9F1F7DA11929687F6F01A4FCB, uuid:85602BF9F1F7DA11929687F6F01A4FCB, uuid:1CEEE81CFE89DB11A823D56643E613AC, uuid:96155451B7D7DB11A6B3DF6C69ACD4DA, uuid:A21FAE3C9AD0DB119A67F03A96C0B626, uuid:ADE5905991F5DA118D069434A1AE4FE6, uuid:F83C597836FADA11B295A6CFA95EAEFC, uuid:1D15E7AEB0FBDA11A58CE92852C2FB31, uuid:B93FCE418107DB11814DB238FB908BC5, uuid:F63C597836FADA11B295A6CFA95EAEFC, uuid:1D15E7AEB0FBDA11A58CE92852C2FB31, uuid:2315E7AEB0FBDA11A58CE92852C2FB31, uuid:2515E7AEB0FBDA11A58CE92852C2FB31, uuid:2315E7AEB0FBDA11A58CE92852C2FB31, uuid:80EB7CEFB1FBDA11A58CE92852C2FB31, uuid:82EB7CEFB1FBDA11A58CE92852C2FB31, uuid:80EB7CEFB1FBDA11A58CE92852C2FB31, uuid:ADE5905991F5DA118D069434A1AE4FE6, uuid:F43C597836FADA11B295A6CFA95EAEFC, uuid:A513561EF1F7DA11929687F6F01A4FCB, uuid:E715A5C72923DB11B879830293AB6491, uuid:A513561EF1F7DA11929687F6F01A4FCB, uuid:A513561EF1F7DA11929687F6F01A4FCB, uuid:B73FCE418107DB11814DB238FB908BC5, uuid:E515A5C72923DB11B879830293AB6491, uuid:B73FCE418107DB11814DB238FB908BC5, uuid:2DFF9042AA8BDB119367B97E56506D21, uuid:37A0C3FD46B8DB11AE04F9CEA4BC49AC, uuid:36e1fbd6-462f-11da-b4e4-0030657b8b80
Format                          : application/pdf
Creator                         : Adobe InDesign CS2 (4.0.4)
EXIF Metadata provided by EXIF.tools
FCC ID Filing: UE3RM1809

Navigation menu