Beautiful Enterprise SFQ04A Bluetooth Module User Manual update

Download:
Mirror Download [FCC.gov]
Document ID	1996507
Application ID	oXsActPeZEwx9N5eBvhipQ==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	27.53kB (344108 bits)
Date Submitted	2013-06-20 00:00:00
Date Available	2013-06-21 00:00:00
Creation Date	2013-06-20 08:59:21
Producing Software	Acrobat Distiller 9.0.0 (Windows)
Document Lastmod	2013-06-20 09:00:18
Document Title	Microsoft Word - User manual-update.DOC
Document Creator	PScript5.dll Version 5.2.2
Document Author:	User

BC05 ROM Module Spec.
Shenzhen Synchron Electronics Co., Ltd. 2012.08
1. General Description and Specification
1.1 General Description
This product is a Class 2 SMT Bluetooth Module used CSR BC5-BlueTunes ROM. It
provides data and voice communications. Support data rate up to 3Mbps.
General Features:
■
Class 2 Bluetooth Module
■
Bluetooth Spec. V2.1+EDR Compliant
■
Support Firmware Upgrade
■
High-quality audio 95dB SNR on DAC playback
■
Integrated linear regulator with 1.5V output from 1.8V to 2.7V input
■
Integrated Switched-mode Regulator
■
Integrated 150mA lithium Battery Charger
■
Integrated Microphone bias& LED Driver
■
64MIPS Kalimba DSP Co-processor
■
cVc support for echo and noise reduction
■
Green (RoHS Compliant)
1.2 Device Details
Radio

Common TX/RX terminal simplifies external matching; eliminates external antenna switch

BIST minimises production test time

Bluetooth v2.1 + EDR specification compliant
Transmitter

4dBm RF transmit power with level control from onchip 6-bit DAC over a dynamic range
>30dB

Class 2 and Class 3 support without the need for an external power amplifier or TX/RX
switch
Receiver

Receiver sensitivity of -70dBm

Integrated channel filters

Digital demodulator for improved sensitivity and cochannel rejection

Real-time digitised RSSI available on HCI interface

Fast AGC for enhanced dynamic range
Baseband and Software

Internal ROM

48KB of internal RAM, allows full-speed data transfer, mixed voice/data and full piconet
support

Logic for FEC, HEC, access code correlation, CRC, demodulation, encryption bit stream
generation, whitening and transmit pulse shaping

Transcoders for A-law, μ-law and linear voice from host and A-law, μ-law and CVSD voice
over air

FastStream, CSR low latency codec significantly, reduces the latency of the audio link,
from source to, sink, avoiding lip-sync issues when simultaneously listening to audio and
watching video images

Bluetooth v2.1 + EDR specification Secure Simple Pairing support

DSP based single-microphone cVc echo and noise reduction is included in the BlueTunes
ROM QFN

A new high-performance dual-microphone noise reduction is available in BlueTunes ROM
QFN as a licensed option for an extra 20dB of noise suppression, order code
BCSW CVC HS 2M R3
Physical Interfaces

Synchronous serial interface for system debugging

I2C compatible interface to external EEPROM containing device configuration data (PS
Keys)

UART interface

Two LED drivers with faders
Kalimba DSP

Very low power Kalimba DSP co-processor, 64MIPS, 24-bit fixed point core

Support for SBC and MP3(1) codec for improved audio quality

Single-cycle MAC; 24 x 24-bit multiply and 56-bit accumulator

32-bit instruction word, dual 24-bit data memory

6K x 32-bit program RAM,8K x 24-bit +8K x 24- bit data RAM

64 x 32-bit program memory cache when executing from ROM
Stereo Audio Codec

16-bit internal codec

DAC for stereo audio

ADC dual channel mono voice band audio

Integrated amplifiers for driving 16Ω speakers; no need for external components

Support for single-ended speaker termination and line output

Integrated low-noise microphone bias
Auxiliary Features

Power management includes digital shutdown and wake-up commands with an integrated
low-power oscillator for ultra-low power Park/Sniff/Hold mode

On-chip regulators: 1.5V output from 1.8V to 2.7V input

On-chip high-efficiency switched-mode regulator; 1.8V output from 2.7V to 4.4V input

Power-on-reset cell detects low supply voltage

10-bit ADC available to applications

On-chip 150mA charger for lithium ion/polymer batteries
1.3 Specification
Chipset
CSR BlueTunes ROM QFN
Specification Version
Bluetooth V2.1+EDR
Power Class
Class 2
Frequency Band
2400~2483.5MHz
Max. Tx Power
-6~+4dBm
RX Sensitivity
＜-70dBm
Distance
>10m(No obstacle)
ROM Size
64K
Power Voltage
3.3V
Supply Current
<40mA
Operation Temperature
-10 ~ +45 ℃
Dimension
32mm(L)x 13.5 mm(W) x 1.2mm(H)
2. Package Information
2.1 Pinout Diagram
Figure 1: BC05 ROM Module Pinout (Top View)
2.2 Terminal Functions
Pin Name
Pin Number
Description
GND
PIO4
PIO5
NC
NC
GND
Ground
GND
Ground
AIO1
AIO0
RESET
System Reset(Low Active)
GND
10
Ground
GND
11
Ground
PIO10
12
PIO11
13
PIO12
14
PIO13
15
NC
16
VDD
17
GND
18
Ground
NC
19
NC
NC
20
NC
GND
21
Ground
GND
22
Ground
NC
23
NC
NC
24
NC
GND
25
Ground
GND
26
Ground
UART_RX
27
UART data input, active high
UART_TX
28
UART data output, active high
GND
29
Ground
GND
30
Ground
GND
31
Ground
GND
32
Ground
SPI_CSB
33
Chip select for SPI, active low
Ground
Programmable input/output line
Analogue programmable input/output line
Programmable input/output line
NC
Positive supply for SPI/UART ports and PIO[13:10]
&PIO[5:0] and EEPROM, Connect to 3.3V
SPI_MISO
34
SPI data output
SPI_CLK
35
SPI clock
SPI_MOSI
36
SPI data input
VRE_IN
37
Take high to enable high-voltage linear regulator
and switch-mode regulator
Lithium
VDD_BAT
38
ion/polymer
battery
positive
terminal.
Battery charger output and input to switch-mode
regulator
GND
39
Ground
VDD_CHG
40
Battery charge input
LED1
41
LED0
42
GND
43
Ground
SPK_L_N
44
Speaker output negative, left
SPK_L_P
45
Speaker output positive, left
SPK_R_N
46
Speaker output negative, right
SPK_R_P
47
Speaker output positive, right
GND_S
48
Signal Ground
MIC_BIAS
49
Microphone bias
MIC_B_P
50
Microphone input positive, right
MIC_B_N
51
Microphone input negative, right
MIC_A_P
52
Microphone input positive, left
MIC_A_N
53
Microphone input negative, left
GND
54
Ground
PIO0
55
PIO1
56
PIO2
57
PIO3
58
GND
59
Ground
RF
60
Transmitter output/switched receiver input
LED Driver
Programmable input/output line
2.3 Package Dimensions
Ø0.45mm X 60
Figure 2: BC05 ROM Module package Dimensions
3. Hardware Description
3.1 Block Diagram
Figure 3: BC05 ROM Module Block Diagram
3.2 RF Ports
Figure 4: RF Ports Diagram
RF_N and RF_P form a complementary balanced pair and are available for both transmit and
receive. On transmit their outputs are combined using an external balun into the single-ended
output required for the antenna. Similarly, on receive their input signals are combined internally.
Both terminals present similar complex impedances that may require matching networks
between them and the balun.
An LC network: L9 and C1. This provides a DC bias for the BlueTunes ROM from the 1.5V rail.
The T2 used to suppress the signal out of Bluetooth Frequency Band and enhance the EMC
capacity.
The DC level must be set at VDD_RADIO.
3.3 UART Ports
BC05 ROM Module UART interface provides a simple mechanism for communicating with
other serial devices using the RS232 protocol. When BlueTunes ROM QFN is connected to
another digital device, UART_RX and UART_TX transfer data between the two devices.
The Baud rate of the UART ports:
Baud rate
Minimum
Maximum
1200 baud (≤2%Error)
9600 baud (≤1%Error)
4Mbaud (≤1%Error)
4. Green Products and RoHS Compliance
5. Reference
1) BlueTunes ROM Product Data Sheet, CS-122312-DSP1
2) Specification of the Bluetooth System, Version 2.1+EDR
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter module must not be co-located or
operating in conjunction with any other antenna or transmitter.
The module must be installed in Sound Kick Audio System.
This End equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop
configurations or co-location with another transmitter), then the FCC authorization is
no longer considered valid and the FCC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end
product (including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following:
“Contains FCC ID:UZZSFQ04A”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
Canada Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
Caution Exposure:
This device meets the exemption from the routine evaluation limits in section 2.5 of
RSS102 and users can obtain Canadian information on RF exposure and compliance.
Le dispositif répond à l'exemption des limites d'évaluation de routine dans la section
2.5 de RSS102 et les utilisateurs peuvent obtenir des renseignements canadiens sur
l'exposition aux RF et le respect.
The final end product must be labelled in a visible area with the following:
The Industry Canada certification label of a module shall be clearly visible at all times
when installed in the host device, otherwise the host device must be labelled to
display the Industry Canada certification number of the module, preceded by the
words “Contains transmitter module”, or the word “Contains”, or similar wording
expressing the same meaning, as follows:
Contains transmitter module IC: 7633A-SFQ04A
The module must be installed in Sound Kick Audio System.
This End equipment should be installed and operated with a minimum distance of 20
centimeters between the radiator and your body.
Cet équipement devrait être installé et actionné avec une distance minimum de 20
centimètres entre le radiateur et votre corps.
The end user manual shall include all required regulatory information/warning as
show in this manual.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : User
Create Date                     : 2013:06:20 08:59:21+08:00
Modify Date                     : 2013:06:20 09:00:18+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c041 52.342996, 2008/05/07-20:48:00
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2013:06:20 09:00:18+08:00
Format                          : application/pdf
Title                           : Microsoft Word - User manual-update.DOC
Creator                         : User
Document ID                     : uuid:ed732ba5-3bf8-44a5-9398-59a5c6b8677f
Instance ID                     : uuid:335c98f4-8d11-43e9-8707-19b61d4af9fb
Page Count                      : 13

EXIF Metadata provided by EXIF.tools