Beijing Smartmi Electronic Technology CJXJSQ02ZM Smartmi Evaporative Humidifier User Manual
Beijing Smartmi Electronic Technology Co., Ltd. Smartmi Evaporative Humidifier
User Manual
小米生态链产品包装图纸 640 材质:太空梭哑粉105g Product Introduction Safety Instructions The Smartmi 2-in-1 Purifier and Humidifier humidifies using evaporation, so it won’t produce a visible mist. Handling · Please turn off and disconnect the machine before moving it. · Please empty the water tank before moving the machine. Installation · Please install the machine according to the instructions provided to avoid electrical shock, fire, Power Cable Adding Water Mode Indicator Water Level Indicator 1 Add water through the refilling port Exhaust / Water Refilling Port Power / Mode Button Wi-Fi / Light Button To avoid risk of fire, shock, or damage: · · · · Plug the power cable into an appropriate socket. Do not pull or stretch the power cable. Disconnect the power cable before performing maintenance, or moving the machine. If the power cable is damaged, send it to the manufacturer or a repair facility to be replaced by professionals. · If the product starts producing a strange sound, odor, or gets very hot, cease use immediately. · Do not put your finger or other foreign objects inside the protective covering, intake port, exhaust Automatic Mode: Automatically adjusts humidifier based on current temperature and humidity inside the room. Speed 1: Low Speed 2: Medium Speed 3: High Wi-Fi Indicator Light Upper Casing Evaporating Basin Knob water heaters) to avoid carbon monoxide poisoning. · If the alarm stops working, it may be caused by water accumulation in the upper casing. It will not Temperature and Humidity Sensor affect use. It should resume working normally after the water has evaporated. Water Level Indicator Light Status Intake Port This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. You can directly add water through the refilling port while the purifier is powered on. The water will flow down into the tank, and the water level indicator will change to reflect how much water has been added. Stop when all the lights are on. Take off the top half of the purifier, and directly add water into the tank. Take care not to fill past the maximum water level indicator. Water Level Detector Water Level Limit Light Status Automatic Mode 10% ≤ Water Level < 40% Power Cable Speed 1: Low 40% ≤ Water Level < 60% Water Level 100% On Over Max Water Level Blinking Off Usage 说明书边角为直角,不做R角 Note: If you fill past the maximum water level, the water level indicator lights will flash and the machine will give off warning beeps, and water should be stopped adding immediately. Off 纹 理 方 向 Specifications Turning the Machine On and Off, and Changing Modes Adjusting Brightness Resetting the Wi-Fi Cleaning the Evaporating Basin Press the Power / Mode Button to turn the machine on. The first time you start the machine, it will default to automatic mode. You can press the button again to switch modes. Holding the button for 2 seconds will turn the machine off. Press the Wi-Fi / Light Button to adjust brightness between high, low, and off. If your phone is unable to connect to the purifier, press and hold both the Wi-Fi / Light button and the Power / Mode button for 5 seconds. Once you hear a beep, the Wi-Fi has been successfully reset. You can remove the evaporating basin and use a soft cloth to wipe down, or clean water to rinse off the basin. You can also twist off the knob on the evaporating basin to clean the individual discs that comprise the basin. Product Name Smartmi Evaporative Humidifier Rated Voltage 100-240V Capacity Approx. 4.0L Model Number CJXJSQ02ZM Rated Frequency 50/60Hz Humidification Rate 240mL / h Dimensions 240 240 363 mm Rated Wattage 8W Wi-Fi Gross Weight Approx. 4.3kg Noise Generated ≤ 47dB(A) Product Type Evaporative Humidifier Net Weight Approx. 5.1kg Network standby power consumption: Wi-Fi IEEE 802.11 b/g/n 2.4GHz < 2.0W Smartmi Evaporative Humidifier Read this manual carefully before use, and retain it for future reference Regulatory compliance information FCC ID: 2AP98-CJXJSQ02ZM Quick Set-up This product is compatible with the Mijia Smart Platform. It can be controlled through the Mijia app, supports the MIUI system, and can connect with other Mijia smart products. Air Dry mode Search for “Mijia” through your app store, or scan the QR code below to install the Mijia app. Enable your phone’s Bluetooth, and go to the front page of the Mijia app. Press the + in the upper right corner, select Add a Device, and select “Smartmi 2-in-1 Purifier and Humidifier”. After adding the device, you should see it on the front page of the Mijia app. If Air Dry mode is on: When the water level drops lower than 10%, the humidifier will continue to operate for about 8 hours to dry out the water tank, avoiding strange odors caused by stagnant water. If Air Dry mode is off: When the water level drops lower than 10%, the humidifier will automatically turn off. Cleaning the Water Tank As illustrated below, you can twist off the knob on the basin to remove the individual disks that comprise the basin. You can rinse the water tank with clean water, or wipe it down with a soft cloth to ensure the cleanliness of your humidifier, and prevent strange odors produced by stagnant or dirty water. SEN OO Note: You can turn the Air Dry mode on or off through the Mijia app. Turn the humidifier off and disconnect the power cable before cleaning the device FAS TE Note: The machine will not turn on if the water level in the tank is lower than the minimum water level. You will have to add water to turn the machine on. Repair and Installation 各色套印不露杂色,套印误差≤ 0.1mm Speed 3: High 80% ≤ Water Level < 100% On 印刷要求:色相正确、印迹牢固、套印准确、 Speed 2: Medium 60% ≤ Water Level < 80% the device is even before use. Current Mode Water Level < 10% Lower Casing · If the purifier is tilted, it may misread the water level in the tank, or cause spills. Please ensure that Mode Indicator Water Level Water Tank Do not use under the following circumstances to avoid shock, fire, or other dangers: Usage 2 Add water into the water tank Evaporating Basin port, or other movable parts. · Do not allow hair or loose threads to get caught in the intake or exhaust ports. · Do not sit or lean on the machine. · Ensure adequate ventilation when used alongside household gas appliances (such as gas stoves or Usage Restrictions Control Panel Instructions bodily harm, or other dangers. · Do not connect the power cable until you have finished setting up the machine. 160 Usage Suitable Water: Tap Water, Mineral Water, Purified Water Control Panel While in Use Product Introduction 材 质 工 艺 要 求 工艺:单色印刷、风琴4折 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. CAUTION: To comply with the limits of the Class B digital device, pursuant to Part 15 of the FCC Rules, this device is comply with Class B limits. All peripherals must be shielded and grounded. Operation with non-certified peripherals or non-shielded cables may results in interference to radio or reception. MODIFICATION: Any changes or modifications not expressly approved by the grantee of this device could void the user’s authority to operate the device. FCC RF EXPOSURE STATEMENT: This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Manufacturer: Beijing Smartmi Electronic Technology Co., Ltd. Address: 11-1102, Office Building Rainbow City, NO.68 Qinghe Mid-Street, Haidian District, Beijing Standard: Q/BJZMK0008-2018 Note: If you frequently use the humidifier, we recommend cleaning it once a week. YT-V1.0(20180531) 智米纯净型加湿器使用说明书英文 V0.9 2018.04.18 韩博 物料编号: 专色:PANTONE Cool Gray 11C 历史 版本 版本号: 修改点: 修改人: 商品ID SKU编码 商品名称 69码 产品型号 比例 智米纯净型加湿器 版本号: 修改点: 修改人: 版本号: 修改点: 修改人: 版本号: 修改点: 修改人: 1:1 版本号: 修改点: 修改人: 单位 mm
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Create Date : 2017:12:13 02:35:11Z Creator : Adobe Illustrator CC 2015 (Macintosh)ÿ(Infix Pro) ICN App Name : Infix Pro ICN App Platform : Windows ICN App Version : 6.47 Modify Date : 2018:06:26 11:33:24 XMP Toolkit : Adobe XMP Core 5.6-c067 79.157747, 2015/03/30-23:40:42 Metadata Date : 2018:05:31 14:17:56+08:00 Creator Tool : Adobe Illustrator CC 2015 (Macintosh) Thumbnail Width : 256 Thumbnail Height : 164 Thumbnail Format : JPEG Thumbnail Image : (Binary data 10095 bytes, use -b option to extract) Instance ID : uuid:96473f15-3227-2c45-889b-fcb6b061db8c Document ID : xmp.did:fed0e18b-c266-43d8-a599-c2157c0e1800 Rendition Class : proof:pdf Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : proof:pdf Derived From Document ID : xmp.did:b181815e-e872-4cca-98af-28839a5ac52f Derived From Instance ID : uuid:cd373148-ec1c-b84f-ba3d-4e7925f066cc Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 History Software Agent : Adobe Illustrator CC 2015 (Macintosh), Adobe Illustrator CC 2015 (Macintosh) History Changed : /, / History When : 2016:09:08 19:38:25+08:00, 2017:02:17 13:12:40+08:00 History Instance ID : xmp.iid:37a7d977-7cd7-4389-acfb-f799ff680de1, xmp.iid:fed0e18b-c266-43d8-a599-c2157c0e1800 History Action : saved, saved N Pages : 1 Has Visible Transparency : True Has Visible Overprint : True Max Page Size W : 1580.779652 Max Page Size H : 1009.071482 Max Page Size Unit : Millimeters Font Name : HelveticaNeueLTStd-Th, AdelleSansTh, AdelleSansLt, AdelleSans, AdelleSansARA-Thin, AdelleSansARA-Light, AdelleSansARA-Regular, HelveticaNeueLTPro-Th, FZYOUH_512B--GB1-4, AdobeSongStd-Light, MicrosoftYaHei, FZLTHK--GBK1-0, FZLTHJW--GB1-0, HelveticaNeueLTStd-Lt, HelveticaNeueLTStd-Roman, FZLTZHUNHK--GBK1-0, FZLTXHK Font Family : Helvetica Neue LT Std, Adelle Sans, Adelle Sans, Adelle Sans, Adelle Sans ARA, Adelle Sans ARA, Adelle Sans ARA, Helvetica Neue LT Pro, 方正悠黑, Adobe 宋体 Std, 微软雅黑, 方正兰亭黑_GBK, 方正兰亭黑简体, Helvetica Neue LT Std, Helvetica Neue LT Std, FZLTZHUNHK -GBK1-0-GBpc-EUC-H, FZLTXHK GBpc-EUC-H Font Face : 35 Thin, Thin, Light, Regular, Thin, Light, Regular, 35 Thin, 512B, L, Regular, Regular, Regular, 45 Light, 55 Roman, -GBK1-0-GBpc-EUC-H, GBpc-EUC-H Font Type : Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, Open Type, TrueType, Open Type, Open Type, TrueType, TrueType, Open Type, Open Type, Unknown, Unknown Font Version : OTF 1.029;PS 001.003;Core 1.0.33;makeotf.lib1.4.1585, Version 2.000, Version 2.000, Version 2.000, Version 2.500;PS 002.500;hotconv 1.0.88;makeotf.lib2.5.64775, Version 2.500;PS 002.500;hotconv 1.0.88;makeotf.lib2.5.64775, Version 2.500;PS 002.500;hotconv 1.0.88;makeotf.lib2.5.64775, Version 1.300;PS 001.003;hotconv 1.0.38, 2.00, Version 5.016;PS 5.002;hotconv 1.0.67;makeotf.lib2.5.33168, Version 0.75, 1.00, 1.00, OTF 1.029;PS 001.002;Core 1.0.33;makeotf.lib1.4.1585, Version 1.047;PS 001.103;Core 1.0.38;makeotf.lib1.6.5960, Version 5.018;PS 5.007;hotconv 1.0.68;makeotf.lib2.5.35818, Version 5.018;PS 5.007;hotconv 1.0.68;makeotf.lib2.5.35818 Font Composite : False, False, False, False, False, False, False, False, False, False, False, False, False, False, False, False, False Font File Name : HelveticaNeueLTStd-Th_0.otf, AdelleSans-Thin.otf, AdelleSans-Light.otf, AdelleSans-Regular.otf, AdelleSansARA-Thin.otf, AdelleSansARA-Light.otf, AdelleSansARA-Regular.otf, HelveticaNeueLTPro-Th.otf, 方正悠黑_大粗.ttf, AdobeSongStd-Light.otf, 微软vista雅黑.ttf, 方正兰亭黑_GBK.TTF, FZLTHJW.TTF, HelveticaNeueLTStd-Lt.otf, HelveticaNeueLTStd-Roman.otf, AdobeHeitiStd-Regular.otf, AdobeHeitiStd-Regular.otf Plate Names : Cyan, Magenta, Yellow, Black, PANTONE Cool Gray 11 C Swatch Group Name : 默认色板组 Swatch Group Type : 0 Swatch Colorant Swatch Name : PANTONE Cool Gray 11 C, AutoCAD Color, PANTONE 477 C, PANTONE 536 C, Artios_注释 Swatch Colorant Type : SPOT, PROCESS, SPOT, SPOT, SPOT Swatch Colorant Tint : 100.000000, 100.000000, 100.000000, 100.000000, 100.000000 Swatch Colorant Mode : CMYK, CMYK, Lab, Lab, CMYK Swatch Colorant Cyan : 72.549021, 92.971694, 100.000000 Swatch Colorant Magenta : 65.098041, 87.972838, 0.000000 Swatch Colorant Yellow : 58.823532, 89.019603, 100.000000 Swatch Colorant Black : 14.509805, 79.998469, 0.000000 Swatch Colorant L : 29.803902, 71.764702 Swatch Colorant A : 18, -2 Swatch Colorant B : 18, -14 Format : application/pdf Title : 米家空气净化器Pro-使用说明书-20161219 Startup Profile : Print Producer : Mac OS X 10.12.6 Quartz PDFContext Page Count : 1 For : , Bounding Box : 0 0 4481 2861 Container Version : 9 Creator Version : 19 Image Height : 2861 Image Width : 4481 Image Size : 4481x2861 Megapixels : 12.8EXIF Metadata provided by EXIF.tools