Bk 894 895 Programming Manual User

2017-02-21

User Manual: Bk 894 895 Programming Manual 894_895_programming_manual en-us programming_manuals s

Open the PDF directly: View PDF PDF.
Page Count: 45

Model: 894/895
500 KHz/1 MHz LCR Meter
PROGRAMMING MANUAL
Table of Contents
Remote Operation ........................................................................................ 6
1.1 Interface Configuration ....................................................................................................... 6
RS-232C ................................................................................................................................... 6
USB (USBCDC - Virtual COM ) .................................................................................................. 7
USBTMC................................................................................................................................... 7
LAN (Ethernet) ......................................................................................................................... 7
GPIB (895 Only) ....................................................................................................................... 8
Command Reference .................................................................................... 9
2.1 IEEE488.2 Common Commands .......................................................................................... 9
*RST ......................................................................................................................................... 9
*TRG ........................................................................................................................................ 9
*CLS ......................................................................................................................................... 9
*IDN? ....................................................................................................................................... 9
*TST? ..................................................................................................................................... 10
*ESE ....................................................................................................................................... 10
*SRE ....................................................................................................................................... 10
*ESR ....................................................................................................................................... 11
*STB? ..................................................................................................................................... 11
*OPC ...................................................................................................................................... 12
2.2 Subsystem commands for 894/895 .................................................................................. 12
2.3 DISPlay subsystem commands .......................................................................................... 13
DISP:PAGE ............................................................................................................................. 14
DISP:LINE ............................................................................................................................... 14
DISPlay:RFONt <font> ........................................................................................................... 15
2.4 FREQuency subsystem commands ................................................................................... 15
FREQ ...................................................................................................................................... 15
2.5 VOLTage subsystem commands ....................................................................................... 16
VOLT ...................................................................................................................................... 16
CURRent ................................................................................................................................ 16
2.6 AMPLitude Subsystem Commands ................................................................................... 16
AMPL ..................................................................................................................................... 16
2.7 Output RESister subsystem commands ............................................................................ 17
ORES ...................................................................................................................................... 17
2.8 OUTPut subsystem commands ......................................................................................... 17
OUTPut:DC:ISOLation ............................................................................................................ 17
2.9 BIAS subsystem commands .............................................................................................. 17
BIAS:STATe ............................................................................................................................ 18
BIAS:VOLTAGE ....................................................................................................................... 18
BIAS:CURRent ........................................................................................................................ 19
2.10 FUNCtion subsystem commands ...................................................................................... 19
FUNCtion:IMPedance ............................................................................................................ 21
FUNCtion:IMPedance:RANGe ............................................................................................... 21
FUNCtion:IMPedance:RANGe:AUTO ..................................................................................... 22
FUNCtion:Source MONitor:VAC ............................................................................................ 22
FUNCtion:SMONitor:IAC ....................................................................................................... 22
FUNCtion:DEV<n>:MODE ...................................................................................................... 22
FUNCtion:DEV<n>:REFerence<value> ................................................................................... 23
FUNCtion:DEV<n>:REFerence:FILL ........................................................................................ 23
2.11 LIST subsystem commands ............................................................................................... 24
LIST:FREQuency ..................................................................................................................... 24
LIST:VOLTage ........................................................................................................................ 25
This ........................................................................................................................................ 25
LIST:CURRent ......................................................................................................................... 25
This ........................................................................................................................................ 25
LIST:BIAS:VOLTage ................................................................................................................ 26
This ........................................................................................................................................ 26
LIST:BIAS:CURRent ................................................................................................................ 26
This ........................................................................................................................................ 26
LIST:MODE ............................................................................................................................. 27
LIST:BAND ............................................................................................................................. 27
LIST:CLEar:ALL ....................................................................................................................... 27
2.12 APERture subsystem commands ...................................................................................... 28
APERture ............................................................................................................................... 28
2.13 TRIGger subsystem commands ......................................................................................... 28
TRIGger.................................................................................................................................. 29
TRIGger:SOURce .................................................................................................................... 29
TRIGger:DELay....................................................................................................................... 29
2.14 FETCh? Subsystem Commands ......................................................................................... 30
FETCh ..................................................................................................................................... 30
2.15 CORRection subsystem commands .................................................................................. 32
CORRection:LENGth .............................................................................................................. 33
CORRection:METHod............................................................................................................. 34
CORRection:OPEN ................................................................................................................. 34
CORRection:OPEN:STATe ...................................................................................................... 35
CORRection:SHORt:STATe ..................................................................................................... 35
CORRection:LOAD:STATe ...................................................................................................... 35
The CORRection:LOAD:TYPE .................................................................................................. 35
CORRection:SPOT<n>:STATe ................................................................................................. 36
CORRection:SPOT<n>:FREQuency ......................................................................................... 37
CORRection:SPOT<n>:OPEN .................................................................................................. 37
CORRection:SPOT<n>:SHORt ................................................................................................ 37
CORRection:SPOT<n>:LOAD:STANdard ................................................................................. 37
CORRection:USE:DATA? ........................................................................................................ 38
CORRection:CLEar ................................................................................................................. 39
2.16 COMParator subsystem commands ................................................................................. 39
COMParator[STATe] .............................................................................................................. 40
COMParator:MODE ............................................................................................................... 40
COMParator:TOLerance:NOMinal ........................................................................................ 40
COMParator:TOLerance:BIN<n> ........................................................................................... 41
COMParator:SEQuence:BIN .................................................................................................. 41
COMParator:SecondaryLIMit ................................................................................................ 41
COMParator:Auxiliary BIN .................................................................................................... 42
COMParator:SWAP ............................................................................................................... 42
COMParator:BIN:CLEar ......................................................................................................... 42
COMParator:BIN:COUNt ....................................................................................................... 43
COMParator:BIN:COUNt:DATA? ........................................................................................... 43
COMParator:BIN:COUNt:CLEar ............................................................................................. 43
2.17 Mass MEMory subsystem commands .............................................................................. 43
MMEMory:LOAD:STATe ........................................................................................................ 44
MMEMory:STORe:STATe ....................................................................................................... 44
Remote Operation
The instrument comes with RS232C, USB (virtual COM), LAN, and GPIB (895 only) interfaces for
remote control. This chapter will describe how users can remotely operate the instrument and
use SCPI (Standard Commands for Programmable Instruments) commands over any one of
these remote interfaces.
1.1 Interface Configuration
RS-232C
For RS-232C connectivity, refer to the diagram below for pinout information. The RS-232C is
labeled in the rear panel and it is a female DB-9 interface. Use a crossover cable where pins 2
and 3 are reversed.
PIN
Description
1
-
2
Transmit Data
3
Receive Data
4
-
5
GND
6
-
7
CTS
8
RTS
9
-
Parameter
Description
Baud rate
9600, 19200, 28800, 38400, 48000, 57600, and 115200.
1
2
3
4
5
6
7
8
9
Parity and
data bit
None/8 bits, Even/8 bits, Odd/8 bits
Stop bit
1, 2
Flow control
None
Table 1 - RS-232C Settings
The RS-232C interface does not support hardware flow control (only
transmit, receive, and ground pins are used). The programmer should be
aware of this limitation and notice the command process time of the LCR
meter. If the remote commands are sent too fast to the LCR meter, the
internal buffer may overrun and cause a communication error. Therefore,
adding a delay between commands is necessary to allow time for the
meter to process.
USB (USBCDC - Virtual COM )
The standard USB port is a virtual COM port that can be used for remote communication. There
are no settings in the menu system for USB configuration. The serial settings are the same as
the settings for RS-232C.
The USB interface does not support hardware flow control (only transmit,
receive, and ground pins are used). The programmer should be aware of
this limitation and notice the command process time of the LCR meter. If
the remote commands are sent too fast to the LCR meter, the internal
buffer may overrun and cause a communication error. Therefore, adding a
delay between commands is necessary to allow time for the meter to
process.
USBTMC
USB The standard USB port is a USBTMC-compliant port that can be used for remote
communication. There are no additional settings in the menu system for USB configuration. The
only requirement is that NI-VISA is installed on the computer, which can be downloaded at
http://www.ni.com/visa/.
LAN (Ethernet)
The 894/895 can also be controlled via LAN interface. Refer to the user manual for setup
information.
GPIB (895 Only)
The GPIB address of the LCR meter can be configured from 1-31. To communicate via GPIB,
connect a GPIB cable to the GPIB port at the back of the LCR meter.
Command Reference
The SCPI interface enables users to operate the power supply through a computer or a terminal
equipped with IEEE-488.2 GPIB, RS-232, or USB interface.
The following table lists all of the numerical parameters:
Symbol
Response Formats
NR1
integer, e.g.:123
NR2
fix-point number, e.g.: 12.3
NR3
floating-point number, e.g.: 12.3E+5
NL
Carriage return key, ASCII code: 10
^END
EOI signal in IEEE-488. EOI gets asserted
on the GPIB interface.
2.1 IEEE488.2 Common Commands
*RST
The *RST command resets the instrument.
Command syntax: *RST
*TRG
The *TRG command triggers the measurement and then sends the result to the output buffer.
Command syntax: *TRG
*CLS
The *CLS command clears the standard event status register and the service request status
register.
Command syntax: *CLS
*IDN?
The *IDN? query returns the instrument’s ID.
Query syntax: *IDN?
Return format: <manufacturer>,<model>,<SN>,<firmware>,<HW_version> <NL^END>
Where,
<manufacturer> Name of Manufacturer ( B&K Precision)
<model> Instrument Model (895)
<SN> XX-XXX-XXXXX
<firmware> Firmware Version (VER1.0.0)
<HW_version> Hardware Version (Hardware Ver XX.X)
*TST?
The *TST? query executes an internal self test and returns the test result as the sum of all
existing errors codes. If there are no error 894/895 returns 0.
Query syntax: *TST?
Return format: <NR1><NL^END>
*ESE
The *ESE (standard Event Status Enable command) command sets each open bit of the
standard event status register. This command returns setups of each open bit for the standard
event status permission register.
Command syntax: *ESE<value>
Query syntax: *ESE?
Return format: <value><NL^END>
Where, <value> NR1 format：decimal number for each bit of operation status register.
Descriptions for each byte of the standard event status register are shown as follows:
*SRE
The *SRE （Service Request Enable command）command sets each open bit of the service
status byte register. This command returns the current setups for each open bit of the status
byte permission register.
Command syntax: *SRE<value>
Query syntax: *SRE?
Return format: <value><NL^END>
Bit number
Description
7
6
5
4
3
2
1
0
Power On(PON) Bit
User Request(URQ) Bit
Command Error(EME) Bit
Execution Error(EXE) Bit
Device Dependent Error(DDE) Bit
Query Error(QYE) Bit
Request Control(RQC) Bit
Operation Complete(OPC) Bit
Where, <value> NR1 format: decimal expression for each permission bit of the status byte
register.
Descriptions for each byte of the status byte register are shown as follows:
*ESR
The *ESR? query returns the contents of the standard event status register.
Query syntax: *ESR?
Return format: <value><NL^END>
Where, <value> NR1 format: decimal expression for contents of the standard event status
register.
Descriptions for each bit of the standard event status register
*STB?
The *STB? query returns contents of the standard service status byte register. The execution of
this command will not affect contents of the standard status byte register.
Query syntax: *STB?
Return format: <value><NL^END>
Where, <value> NR1 format: decimal expression for contents of the standard status byte
register.
Descriptions for each bit of the standard status byte register:
Bit number
Description
7
6
5
4
3-0
Operation Status Register Summary Bit
RQS(Request Service) Bit
Standard Event Status Register Summary Bit
MAV(Message Available) Bit
Always 0(zero):
Bit number
Description
7
6
5
4
3
2
1
0
Power On(PON) Bit
User Request(URQ) Bit
Command Error(EME) Bit
Execution Error(EXE) Bit
Device Dependent Error(DDE) Bit
Query Error(QYE) Bit
Request Control(RQC) Bit
Operation Complete(OPC) Bit
*OPC
The *OPC command equals to set the OPC bit of the standard event status register when
894/895 finishes all parameter measurements. Ever since all pending operations have been
completed, this command will inform the instrument to add a ASCII number “1” (number: 49)
into the output buffer.
Command syntax: *OPC
For example: OUTPUT 717; “*OPC” Sets the OPC bit of the instrument when the last command
is done.
Query syntax: *OPC?
Return format: 1<NL^END>
2.2 Subsystem commands for 894/895
Find below a list of the subsystem commands for the LCR meter. For SCPI commands, there is a
short and long form. In the list below, find the short version in bold and in capital letters, the
long version of the command is the entire word.
Short Version
Long Version
DISP
DISPlay
FREQ
FREQuency
VOLT
VOLTage
CURR
CURRent
AMPL
AMPLitude
ORES
Output RESistance
OUTP
OUTPut
BIAS
BIAS
FUNC
FUNCtion
LIST
LIST
APER
APERture
TRIG
TRIGger
FETC
FETCh?
CORR
CORRection
Bit number
Description
7
6
5
4
3-0
Operation Status Register Summary Bit
RQS(Request Service) Bit
Standard Event Status Register Summary Bit
MAV(Message Available) Bit
Always 0(zero)
COMP
COMParator
MMEM
Mass MEMory
2.3 DISPlay subsystem commands
The command tree for the Display Subsystem is as follows:
DISP:PAGE
DISPlay subsystem commands are used to configure the display pages of the instrument.
Command Syntax
DISPlay:PAGE<page name>
Query syntax
DISPlay:PAGE?
Query returns the current page.
Return format
<page name><NL^END>
Example 1
DISP:PAGE MEAS
Set the display page as the LCR measurement
display page.
Example 2
DISP:PAGE?
Returns: MEAS DISP
Where <Page name> can be set as the following items:
Page name
Function
MEASurement
Set the display page as the LCR measurement
display.
BNUMber
Set the display page as the bin number display.
BCOunt
Set the display page as the bin count display.
LIST
Set the display page as the list sweep display.
MSETup
Set the display page as the measurement display.
CSETup
Set the display page as the correction setup.
LTABle
Set the display page as the limit table setup.
LSETup
Set the display page as the list sweep setup.
SYSTem
Set the display page as the system setup page.
FLISt
Set the display page as the file list page.
DISP:LINE
The DISP:LINE command is used to enter comments containing up to 16 ASCII characters in the
comment field. The string “BK89xATS” is displayed if this is empty.
Command Syntax
DISPlay:LINE ”<string>”
Query syntax
DISPlay:LINE?
Return format
Return format: <string><NL^END>
Example 1
DISP:LINE “ResistanceValues”
Assigns a representative name to the string.
Example 2
DISP:LINE?
Returns:
ResistanceValues
Where <string> can be an ASCII character string (maximum number is 16).
DISPlay:RFONt <font>
The ResultFONt command is used to set the current font of the measurement result on the
<MEAS DISPLAY> PAGE.
Command Syntax
DISPlay:RFONt <font>
Query syntax
DISPlay:ResultFONt?
Return format
Return format: <font><NL^END>
Where <font> can be any of the following options:
Item
Function
LARGe
Use large character to display the measurement
result, 12ms/meas.
TINY
Use tiny character to display the measurement
result, 5ms/meas.
OFF
Measurement result will not be displayed but can
be read from the bus.
2.4 FREQuency subsystem commands
FREQ
Sets the measurement frequency of the instrument.
Returns the measurement frequency being used to do measurements.
Command Syntax
FREQuency <value>
Query syntax
FREQuency?
Return format
<NR3><NL^END>
Example
FREQ 1MHZ
Where <value> can be: NR1, NR2 or NR3 (followed by Hz, kHz, MHz), MIN or MAX.
MIN= Set the measurement frequency as 20Hz.
MAX= Set the measurement frequency as 500 KHz for the 894 or 1 MHz for the 895.
2.5 VOLTage subsystem commands
VOLT
The VOLTage subsystem commands are used to set and query the measurement voltage level.
Command Syntax
VOLTage <value>
Query syntax
VOLTage?
Return format
<NR3><NL^END>
Example
VOLT 0.500 V
Sets measurement voltage level to 500 mV.
Where <value> can be: NR1, NR2 or NR3 data format followed by V.
MIN= Set the measurement voltage as 5mV.
MAX= Set the measurement voltage as 2V.
CURRent subsystem commands
CURRent
The CURRent subsystem commands are used to set and query the current level for the
measurement signal.
Command Syntax
CURRent <value>
Query syntax
CURRent?
Return format
<NR3><NL^END>
Example 1
CURR 10MA
Sets the current level for the measurement
signal to 10 mA.
Where <value> NR1, NR2 or NR3 data format followed by MA.
MIN Set the measurement current as 50μA.
MAX Set the measurement current as 66.67mA.
MIN and MAX value changes depending on impedance range.
2.6 AMPLitude Subsystem Commands
AMPL
The AMPLitude subsystem commands are mainly used to set the auto level control (ALC)
function.
Command Syntax
AMPL:ALC <status>
Query syntax
AMPLitude:ALC?
Return format
<NR1><NL^END>
Example 1
AMPL:ALC ON
Turn function Auto Level Control (ALC) on.
Where <status> can be: 0 or OFF, or 1 or ON
2.7 Output RESister subsystem commands
ORES
The Output RESister subsystem commands are used to set the output impedance of the LCR meter.
Command Syntax
ORESister <impedance>
Query syntax
ORESister?
Return format
<NR1><NL^END>
Example 1
ORES 30
Set the output internal resistance is 30 OHM.
Where <impendance> can be either 30, 50 or 100.
2.8 OUTPut subsystem commands
OUTPut:DC:ISOLation
The OUTPut subsystem commands are used to set the Bias Current Isolation function of the
50mA/5V DC bias source as ON or OFF.
Command Syntax
OUTPut:DC:ISOLation <status>
Query syntax
OUTPut:DC:ISOLation?
Return format
<NR1><NL^END>
Example 1
OUTP:DC:ISOL 1
Turns the Bias Current Isolation function on.
Example
OUTP:DC:ISOL OFF
Turns the Bias Current Isolation function off.
Where <status> can be: 0 or OFF, or 1 or ON.
2.9 BIAS subsystem commands
The BIAS subsystem command are used to set the status of the DC Bias Function (on/off), bias
voltage, and bias current.
Refer to the image below for command tree:
BIAS:STATe
This command is used to turn the DC BIAS Function on or off.
Command Syntax
BIAS:STATe <state>
Query syntax
Query syntax: BIAS:STATe?
Return format
<NR1><NL^END>
Example 1
BIAS:STATe 0
Turns the DC BIAS Function off.
Where <state> can be: 0 or OFF, or 1 or ON.
BIAS:VOLTAGE
This command is used to set the internal DC bias voltage.
Command Syntax
BIAS:VOLTage <value>
Query syntax
BIAS:VOLTage?
Return format
<NR3><NL^END>
Example 1
BIAS:VOLT ON
Turn the internal DC bias voltage on.
Where <value> can be: NR1, NR2 or NR3 data format followed by V.
MIN= Set the measurement voltage as +/-5mV.
MAX= Set the measurement voltage as +/-2V.
BIAS:CURRent
Command Syntax
BIAS:CURRent <value>
Query syntax
BIAS:CURRent?
Return format
<NR3><NL^END>
Example 1
BIAS:CURR 40MA
Where <value> can be: NR1, NR2 or NR3 data format followed by MA.
MIN= Set the measurement voltage as +/- 0 mA.
MAX= Set the measurement voltage as +/-50 mA.
2.10 FUNCtion subsystem commands
The FUNCtion subsystem commands are used to set measurement functions, range,
current/voltage monitor ON/OFF, deviation display mode, and nominal setting.
Refer to the image in the next page for the command tree of the FUNCtion Subsytem.
FUNCtion:IMPedance
The FUNCtion:IMPedance command is used to set and select the measurement function.
Command Syntax
FUNCTion:IMPedance <function>
Query syntax
FUNCTion:IMPedance?
Return format
<function><NL^END>
Example 1
FUNC:IMP RX
Set the function as R-X.
Where <function> is one of the selections below:
Function
Mode
Function
Mode
CPD
Set the function as Cp-D
LPRP
Set the function as Lp-Rp
CPQ
Set the function as Cp-Q
LSD
Set the function as Ls-D
CPG
Set the function as Cp-G
LSQ
Set the function as Ls-Q
CPRP
Set the function as Cp-Rp
LSRS
Set the function as Ls-Rs
CSD
Set the function as Cs-D
RX
Set the function as R-X
CSQ
Set the function as Cs-Q
ZTD
Set the function as Z-θ◦
CSRS
Set the function as Cs-Rs
ZTR
Set the function as Z-θr
LPQ
Set the function as Lp-Q
GB
Set the function as G-B
LPD
Set the function as Lp-D
YTD
Set the function as Y-θ◦
LPG
Set the function as Lp-G
YTR
Set the function as Y-θr
FUNCtion:IMPedance:RANGe
Selects the impedance measurement range. This command turns the auto range function OFF
when is used.
Command Syntax
FUNCTion:IMPedance:RANGe <value>
Query syntax
FUNCTion:IMPedance:RANGe?
Return format
<value><NL^END>
Example 1
FUNC:IMP:RANG 1KOHM
Set the value of the range to 1kOHM
Where, <value> can be the impedance of the DUT or NR1, NR2 or NR3 data format
followed by OHM or KOHM.
10
30
100
300
1000
3000
10000
30000
100000
FUNCtion:IMPedance:RANGe:AUTO
The FUNCtion:IMPedance:RANGe:AUTO command is used to set the automatic range selection
status.
Command Syntax
FUNCTion:IMPedance:RANGe:AUTO <status>
Query syntax
FUNCTion:IMPedance:RANGe?
Return format
<NR1><NL^END>
Example 1
FUNC:IMP:RANG:AUTO ON
Set the automatic range as ON.
Where <status> can be: 0 or OFF, or 1 or ON.
FUNCtion:Source MONitor:VAC
The FUNCtion:Source MONitor:VAC command is used to set the voltage monitor ON or OFF.
Command Syntax
FUNCtion:SMONitor:VAC <status>
Query syntax
FUNCtion:SMONitor:VAC?
Return format
<NR1><NL^END>
Example 1
FUNC:SMON:VAC ON
Set the voltage monitor as ON.
Where <status> can be: 0 or OFF, or 1 or ON.
FUNCtion:SMONitor:IAC
The FUNCtion:SMONitor:IAC command enables the AC current-level monitor function.
Command Syntax
FUNC:SMONitor:IAC <status>
Query syntax
FUNCtion:SMONitor:IAC?
Return format
FUNCtion:SMONitior:IAC?
Example 1
<NR1><NL^END>
FUNCtion:DEV<n>:MODE
The FUNCtion:DEV<n>:MODE command is used to set and query the deviation measurement
mode.
Command Syntax
FUNCtion:DEV<n>:MODE<deviation>
Query syntax
Query syntax: FUNCtion:DEV<n>:MODE?
Return format
<deviation><NL^END>
Example 1
FUNC:DEV1:MODE ABS
Where <deviation> can be:
ABSolute Absolute value deviation display
PERCent Percent deviation display
OFF Real value display
When n=1 the deviation mode is being set to the nominal value of primary parameter.
When n=2 the deviation mode is being set to the nomial value of the secondary
parameter.
FUNCtion:DEV<n>:REFerence<value>
This command is used to set the nominal value of the deviation.
Command Syntax
FUNCtion:DEV<n>:REFerence<value>
Query syntax
FUNCtion:DEV<n>:REFerence?
Return format
<NR3><NL^END>
Example 1
FUNC:DEV1:REF 10
Where, <value> can be 1 or 2.
When n=1, equal to the nominal value of primary parameter.
When n=2, is equal to the nominal value of the secondary parameter.
Where, <value> is NR1, NR2 or NR3 data format.
FUNCtion:DEV<n>:REFerence:FILL
This command is used to set the nominal value of the deviation. This command directs the
instrument to make a test and then copies the results of the primary and the secondary
parameters as the nominal values of the deviation.
Command Syntax
FUNCtion:DEV<n>:REFerence:FILL
Query syntax
N/A
Example 1
FUNC:DEV1:REF:FILL
Where, <value> can be 1 or 2.
When n=1, equal to the nominal value of primary parameter.
When n=2, is equal to the nominal value of the secondary parameter.
2.11 LIST subsystem commands
The LIST subsystem commands are mainly used to set the list sweep function, sweep points,
sweep mode, sweep limits.
LIST:FREQuency
This command is used to clear the original sweep points and set the frequencies of a new list
frequency sweep points.
Command Syntax
LIST:FREQuency <value>[, <value>*]
Query syntax
LIST:FREQuency?
Return format
<NR3>, [,<NR3>*]<NL^END>
Example
LIST:FREQ 133, 1KHZ, 1MHZ, 4E3
Set the frequency of the sweep point 1 as 133 Hz
Set the frequency of the sweep point 2 as 1KHZ
Set the frequency of the sweep point 3 as 1MHZ
Set the frequency of the sweep point 4 as 4KHZ.
* 201 sweep points, at most, can be set.
Where, <value> is NR1, NR2 or NR3 data format.
<value> is 20HZ to 500KHZ (894), 20HZ to 1MHZ (895), if a value outside this range is
sent, that specific sweep point will be ignored and it will generate errors when querying
this command.
The units of frequency, Hz, could be used after the frequency value, as shown in the
example above. HZ (hertz) is the default unit.
LIST:VOLTage
This command is used to clear the voltage of each sweep point by overwriting the set values
with the new values sent and clearing the points that are not set in the new list.
Command Syntax
LIST:VOLTage <value>[, <value>*]
Query syntax
LIST:VOLTage?
Return format
<NR3>[, <NR3>*]<NL^END>
Example 1
LIST:VOLT\s5E-3,\s2E-2,\s0.035V,\s200MV\n
Set the voltage of the sweep point 1 as 5 mV
Set the voltage of the sweep point 2 as 20 mV
Set the voltage of the sweep point 3 as 35 mV
Set the voltage of the sweep point 4 as 200mV.
* 201 sweep points, at most, can be set.
Where, <value> is NR1, NR2 or NR3 data format.
<value> should be set from 5mV to 2V, if a value outside this range is sent, that specific
sweep point will be ignored and it will generate errors when querying this command.
The unit of volts (V) or milli Volts (MV) could be used after the voltage value, as shown
in the example above. Volts (V) is the default unit.
LIST:CURRent
This command is used to clear the current of each sweep point by overwriting the set values
with the new values sent and clearing the points that are not set in the new list.
Command Syntax
LIST:CURRent<value>[, <value>*]
Query syntax
LIST:CURRent?
Return format
<NR3>[, <NR3>*]<NL^END>
Example 1
LIST:CURR 5E-3, 20, 0.015A, 10MA
Set the voltage of the sweep point 1 as 5 mA.
Set the voltage of the sweep point 2 as 20 mA.
Set the voltage of the sweep point 3 as 15 mA.
Set the voltage of the sweep point 4 as 10 mA.
* 201 sweep points, at most, can be set.
Where, <value> is NR1, NR2 or NR3 data format.
<value> should be set from 50μA to 20mA, if a value outside this range is sent, that
specific sweep point will be ignored and it will generate errors when querying this
command.
The unit of volts (A) or milli Amps (MAV could be used after the current value, as shown
in the example above. Volts (V) is the default unit.
LIST:BIAS:VOLTage
This command is used to clear the DC Bias Voltage of each sweep point by overwriting the set
values with the new values sent and clearing the points that are not set in the new list.
Command Syntax
LIST:BIAS:VOLTage<value>[, <value>*]
Query syntax
LIST:BIAS:VOLTage?
Return format
<NR3>[, <NR3>*]<NL^END>
Example 1
LIST:BIAS:VOLT 1E-4, 2E-2, 5, 4V
Set the voltage of the sweep point 1 as 0.1 mV.
Set the voltage of the sweep point 2 as 20 mV.
Set the voltage of the sweep point 3 as 5 V.
Set the voltage of the sweep point 4 as -4 V.
* 201 sweep points, at most, can be set.
Where, <value> is NR1, NR2 or NR3 data format.
<value> should be set from -5 V to 5 V, if a value outside this range is sent, that specific
sweep point will be ignored and it will generate errors when querying this command.
The unit of volts (V) or milli Volts (MV) could be used after the voltage value, as shown
in the example above. Volts (V) is the default unit.
LIST:BIAS:CURRent
This command is used to clear the DC Bias Current of each sweep point by overwriting the set
values with the new values sent and clearing the points that are not set in the new list.
Command Syntax
LIST:BIAS:CURRent<value>[, <value>*]
Query syntax
LIST:BIAS:CURRent?
Return format
<NR3>[, <NR3>*]<NL^END>
Example 1
LIST:BIAS:CURR 1E-4, 2E-2, 5mA, -2mA.
Set the voltage of the sweep point 1 as 100 uA.
Set the voltage of the sweep point 2 as 20 mA.
Set the voltage of the sweep point 3 as 5 mA.
Set the voltage of the sweep point 4 as -2 mA.
* 201 sweep points, at most, can be set.
Where, <value> is NR1, NR2 or NR3 data format.
<value> should be set from -50 mA to +50 mA, if a value outside this range is sent, that
specific sweep point will be ignored and it will generate errors when querying this
command.
The unit of volts (A) or milli Amps (MAV could be used after the current value, as shown
in the example above. Volts (V) is the default unit.
LIST:MODE
This command is used to set the list sweep mode.
Command Syntax
LIST:MODE <mode>
Query syntax
LIST:MODE?
Return format
<mode><NL^END>
Example 1
LIST:MODE SEQ
Where, <mode> can be:
SEQuence: Sequential mode.
STEPped: Single step mode. One step per trigger signal.
LIST:BAND
This command is used to set the limits of list sweep table.
Command Syntax
LIST:BAND<n><parameter>[,<low limit n>,<high
limit n>]
Query syntax
LIST:BAND<n>?
Return format
<parameter>, <low limit n>, <high limit n>
Example 1
LIST:BAND3 OFF
Where:
<n> can be 1 to 201 (NR1 format): sweep points on the nth line
<parameter> can be A or B:
A= Compare the primary parameter of the test results with the high and the low limits.
B= Compare the secondary parameter of the test results with the high and the low
limits.
OFF No comparison
<low limit n> NR1, NR2 or NR3 data format, low limit of the sweep point on the nth line.
<high limit n> NR1, NR2 or NR3 data format, high limit of the sweep point on the nth line.
LIST:CLEar:ALL
This command is used to clear the setting data of all sweep points.
Command Syntax
LIST:CLEAR:ALL
Query syntax
N/A
Return format
N/A
Example 1
LIST:CLEAR:ALL
2.12 APERture subsystem commands
The APERture subsystem commands are used to set the measurement speed, averaging times
used in measurement.
APERture
This command is used to set the measurement speed and the averaging times used during
measurements.
Command Syntax
APERture <speed> [,<value>]
Query syntax
APERture?
Return format
<speed>, <NR1><NL^END>
Example 1
APER MED, 55
Sets the speed to MEDIUM, and averaging times
to 55. This means that the meter will take 55
measurements at medium speed and present
the average as the result.
2.13 TRIGger subsystem commands
The TRIGger subsystem commands are used to set the instrument trigger source, trigger delay
and trigger measurement.
Command tree:
TRIGger
This command is used to send a trigger signal to the LCR meter and start a test.
Command syntax: TRIGger[:IMMediate]
For example:
Command Syntax
TRIGger[:IMMediate]
Query syntax
N/A
Return format
N/A
Example 1
WrtCmd(“TRIG”)
TRIGger:SOURce
This command is used to set the trigger source mode.
Command Syntax
TRIGger:SOURce <source>
Query syntax
TRIGger:SOURce?
Return format
<source><NL^END>
Example 1
TRIG:SOUR BUS
Where:
INTernal The default trigger mode.
EXTernal Triggered by HANDLER interface.
BUS Triggered by RS232C interface or GPIB interface
HOLD Triggered by pressing TRIGGER.
TRIGger:DELay
This command is used to set the delay time after triggering.
Command Syntax
TRIGger:DELay <value>
Query syntax
TRIGger:DELay?
Return format
<NR3><NL^END>
Example 1
TRIG:DEL 5s
Set the trigger delay to 5 seconds
Where <value> is in the NR1, NR2 or NR3 data format and a valid range from 0 to
60s with 1ms as the resolution.
MIN Set the delay time as 0s.
MAX Set the delay time as 60s.
2.14 FETCh? Subsystem Commands
The FETCh? subsystem commands are used to direct the 894/895 to fetch the last to input a
measurement result.
FETCh
This command queries the last measurement of the from the output buffer.
Command Syntax
N/A
Query syntax
FETCh[:IMP]?
Return format
<DATA A>,<DATA B>,<Status>,<BIN
number><NL^END>
Example 1
FETC?
Queries the last measurement on the output
buffer.
Where:
<DATA A> = primary measurement data.
<DATA B> = secondary measurement data.
The return format will be displayed as follows:
SN.NNNNNeSNN
,
SN.NNNNNeSNN
,
SN
NL^END
<DATA A>
<DATA B>
<Status>
New line
Where:
S = +/-
N= 0 to 9
e = Exponent (1.03e-3 = 0.00103)
<status> return format uses 2 ASCII characters, plus or minus and the value which as
the following table details can be a value between -1 and +4.
<status> will display the measurement status with the following values:
<status> format is SP, where “S” is as described above and “P” valid values are from 0 to
4.
Status
Description
S
N
-
0
+
+
+
+
1
0
1
2
3
4
No data in buffer memory
Normal measurement data
Analog LCR unbalance
A/D converter is not working.
Signal source is over loading.
Constant voltage cannot be adjusted.
When the COMPARE function is enabled:
The LCR will not return the following string:
SN.NNNNNeSNN
,
SN.NNNNNeSNN
,
SN
,
SN
NL^END
<DATA A>
<DATA B>
<Status>
<result>
New line
<Bin number>
Bin data is only available and displayed only when compare function is set as ON.
The data displays the sorting results of the displayed bin, shown below.
Data
Sort result
0
+1
+2
+3
+4
Out of tolerance
Bin 1
Bin 2
Bin 3
Bin 4
+5
+6
+7
+8
+9
+10
Bin 5
Bin 6
Bin 7
Bin 8
Bin 9
Auxiliary bin
2.15 CORRection subsystem commands
The CORRection subsystem commands are used to set and select the correction function:
OPEN, SHORT, LOAD.
Command tree:
CORRection:LENGth
This command is used to the correction factor for the cable length.
Command Syntax
CORRection:LENGth<value>
Query syntax
CORRection:LENGth?
Return format
<NR1><NL^END>
Example 1
CORR:LENG 1M
Set the correction factor for a cable of 1 meter.
Where <value> is 0, 1, 2 or 4 followed by M.
CORRection:METHod
This command is used to set the correction mode to single or multi-channel.
Command Syntax
CORRection:METHod <method>
Query syntax
CORRection:METHod?
Return format
<method><NL^END>
Example 1
CORR:METH SING
Where <method> can be:
SINGle Set or return single channel mode.
MULTi Set or return multi-channel mode.
CORRection:OPEN
This command is used to execute an open correction for the following preset test points.
Command Syntax
CORRection:OPEN
Query syntax
N/A
Return format
N/A
Example 1
CORR:OPEN
Hz
Hz
kHz
kHz
kHz
MHz
20
100
1.0
10
100
1*
25
120
1.2
12
120
30
150
1.5
15
150
*895 only
40
200
2.0
20
200
50
250
2.5
25
250
60
300
3.0
30
300
80
400
4.0
40
400
500
5.0
50
500
600
6.0
60
600*
800
8.0
80
800*
CORRection:OPEN:STATe
This command is used to set the open correction ON or OFF.
Command Syntax
CORRection:OPEN:STATe <state>
Query syntax
CORRection:OPEN:STATe?
Return format
<NR1><NL^END>
Example 1
CORR:OPEN:STAT ON
Turns the Open Correction function ON.
Where, <state> can be:
ON = 1
OFF = 0
CORRection:SHORt:STATe
This command is used to set the Short Correction ON or OFF.
Command Syntax
CORRection:SHORt:STATe <state>
Query syntax
CORRection:SHORt:STATe?
Return format
<NR1><NL^END>
Example 1
CORR:SHORt:STAT OFF
Turns the Short Correction function OFF.
Where, <state> can be:
ON = 1
OFF = 0
CORRection:LOAD:STATe
This command is used to set the Load Correction ON or OFF.
Command Syntax
CORRection:LOAD:STATe <state>
Query syntax
CORRection:LOAD:STATe?
Return format
<NR1><NL^END>
Example 1
CORR:LOADt:STAT OFF
Turns the Load Correction function OFF.
Where, <state> can be:
ON = 1
OFF = 0
The CORRection:LOAD:TYPE
This command is used to set the test parameter type.
Command Syntax
CORRection:LOAD:TYPE <type>
Query syntax
CORRection:LOAD:TYPE?
Return format
<function><NL^END>
Example 1
CORR:LOAD:TYPE CPD
Sets the Correction Load Type to use the
capacitance in parallel mode, and dissipation
factor to be used during the correction.
Where, <type> can be:
TYPE
FUNCTION
TYPE
Function
CPD
Set the function as Cp-D
LPRP
Set the function as Lp-Rp
CPQ
Set the function as Cp-Q
LSD
Set the function as Ls-D
CPG
Set the function as Cp-G
LSQ
Set the function as Ls-Q
CPRP
Set the function as Cp-Rp
LSRS
Set the function as Ls-Rs
CSD
Set the function as Cs-D
RX
Set the function as R-X
CSQ
Set the function as Cs-Q
ZTD
Set the function as Z-θ◦
CSRS
Set the function as Cs-Rs
ZTR
Set the function as Z-θr
LPQ
Set the function as Lp-Q
GB
Set the function as G-B
LPD
Set the function as Lp-D
YTD
Set the function as Y-θ◦
LPG
Set the function as Lp-G
YTR
Set the function as Y-θr
CORRection:SPOT<n>:STATe
This command is used to set and query the state of the correction spot. It lets the user turn on
or off specific points during the spot correction.
Command Syntax
CORRection:SPOT <n>:STATe <state>
Query syntax
CORRection:SPOT <n>:STATe?
Return format
<NR1><NL^END>
Example 1
CORR:SPOT 11:STAT ON
Turn the Spot Correction of spot #11 on.
Where,
<state>: 0 or OFF, or 1 or ON
<n>: 0 or OFF, or 1 or ON.
CORRection:SPOT<n>:FREQuency
This command is used to set the frequency of the correction spots.
Command Syntax
CORRection:SPOT<n>:FREQeuency<value>
Query syntax
CORRection:SPOT<n>:FREQuency?
Return format
<NR3><NL^END>
Example 1
CORR:SPOT 15:FREQ 2KHZ
Set the Spot Correction in spot 15 to 2 Khz.
Where,
<value>: NR1, NR2 or NR3 data format followed by HZ, KHZ and MHZ. Range is 20 Hz to
500 kHz (894) 20 Hz to 1 MHz (895).
<n>: One of the 201 correction spots.
CORRection:SPOT<n>:OPEN
This command is used to execute open correction for the current correction spot.
Command Syntax
CORRection:SPOT <n>:OPEN
Query syntax
N/A
Return format
N/A
Example 1
CORR:SPOT 1:OPEN
Executes an open correction in spot #1.
Where,
<n>: One of the 201 correction spots.
CORRection:SPOT<n>:SHORt
This command is used to execute short correction for the current correction spot.
Command Syntax
CORRection:SPOT <n>:SHORT
Query syntax
N/A
Return format
N/A
Example 1
CORR:SPOT 10:SHORT
Executes a short correction in spot #10.
Where,
<n>: One of the 201 correction spots.
CORRection:SPOT<n>:LOAD:STANdard
This command is used to set the standard reference of the current correction spot.
Command Syntax
CORRection:SPOT <n>:LOAD:STANdard <REF. A>
<REF. B>
Query syntax
CORRection:SPOT <n>:LOAD:STANdard?
Return format
<NR3><NL^END>
Example 1
CORR:SPOT1:LOAD:STAN 100.7, 0.0002
Set the standard reference value for spot #1, to
100.7 for the primary , and 0.0002 for the
secondary parameter.
Where,
<n>: One of the 201 correction spots.
<REF. A> can be NR1, NR2 or NR3 data format and taken as the standard reference of
the primary parameter.
<REF. B> can be NR1, NR2 or NR3 data format and taken as the standard reference of
the secondary parameter.
CORRection:USE:DATA?
This query returns the OPEN/SHORT/LOAD correction measurement data of 201 correction
spots.
Command Syntax
N/A
Query syntax
CORRection:USE:DATA? <channel number>
Return format
See below.
Example 1
CORRection:USE:DATA?
<open1 A>,<open1 B>,<short1 A>,<short1 B>,<load1 A>,<load1 B>,
<open2 A>,<open2 B>,<short2 A>,<short2 B>,<load2 A>,<load2 B>,
<open3 A>,<open3 B>,<short3 A>,<short3 B>,<load3 A>,<load3 B>,
…
Where,
<open n A> is NR3 data format and the primary open correction data at the correction
spot n.
<open n B> is NR3 data format and the secondary open correction data at correction
spot n.
<short n A> is NR3 data format and the primary short correction data at correction spot
n.
<short n B> is NR3 data format and the secondary short correction data at correction
spot n.
<load n A> is NR3 data format and the primary load correction data at correction spot n.
<load n B> is NR3 data format and the secondary load correction data at correction spot
n.
CORRection:CLEar
This command is used to clear the correction data of all the correction spots.
Command Syntax
CORRection:CLEar
Query syntax
N/A
Return format
N/A
Example 1
CORRection:CLEar
Clears the correction data.
2.16 COMParator subsystem commands
The COMParataor subsystem commands are used to set the bin comparator function including
ON/OFF setting, and Limit table setting.
Command tree:
COMParator[STATe]
This command is used to set the comparator function ON or OFF.
Command Syntax
COMParator <state>
Query syntax
COMParator <state>?
Return format
<NR1><NL^END>.
Example 1
COMP ON
Turns the comparator ON.
Where,
<state>: 0 or OFF, or 1 or ON
COMParator:MODE
This command is used to set the comparator mode.
Command Syntax
COMParator:MODE <mode>
Query syntax
COMParator:MODE?
Return format
<mode><<NL^END>
Example 1
COM:MODE ATOL
Set the comparator mode to absolute tolerance
mode.
Where,
ATOLerance means absolute tolerance mode.
PTOLerance means proportional tolerance mode.
SEQuence means sequential tolerance mode.
COMParator:TOLerance:NOMinal
This command is used to set the nominal value (this function is valid only when the limit mode
is set as deviation mode).
Command Syntax
COMParator:TOLerance:NOMinal<value>
Query syntax
COMParator:TOLerance:NOMinal?
Return format
<NR3><NL^END>
Example 1
COMP:TOL:NOM 100E-12
Sets the tolerance nominal value, when the limit
mode is set as deviation mode, to 100E-12.
<value> is a nominal value in NR1, NR2 or NR3 data format.
COMParator:TOLerance:BIN<n>
This command is used to set the high and the low limits of each bin (this function is valid only
when the limit mode is set as deviation mode).
The COMParator:TOLeance:BIN<n>?
Command Syntax
COMParator:TOLerance:BIN<n><low limit><high
limit>
Query syntax
COMParator:TOLeance:BIN<n>?
Return format
<low limit><high limit><NL^END>
Example 1
COMP:TOL:BIN2 -10,10
Set the high value of bin 2 to 10.
Set the low value of bin 2 to -10
Where,
<n> is the bin number from 1 to 9.
<low limit> is the low limit in NR1, NR2 or NR3 data format.
<high limit> is the high limit in NR1, NR2 or NR3 data format.
The low limit should be smaller than the high limit or an error will be issued.
COMParator:SEQuence:BIN
This command is used to set the high and the low limits of sequential mode (this function is
valid only when the limit mode is set as the sequential mode).
Command Syntax
COMParator:SEQuence:BIN <BIN1 low limit>,
<BIN 1 high limit>, <BIN2 high limit>, …, <BINn
high limit>
Query syntax
COMParator:SEQuence:BIN?
Return format
<BIN1 low limit>, <BIN1 high limit>, <BIN2 high
limit>, …,<BINn high limit><NL^END>
Example 1
COMP:SEQ:BIN 10, 20, 30, 40, 50
Where,
<BIN1 low limit> is the low limit of BIN 1 in NR1, NR2 or NR3 data format.
<BIN1 high limit> is the high limit of BIN1 in NR1, NR2 or NR3 data format.
<BINn high limit> is the high limit of BINn (the maximum of n is 9) in NR1, NR2 or NR3
data format.
The low limit should be smaller than the high limit or an error will be issued.
COMParator:SecondaryLIMit
This command is used to set the high and the low limits of the secondary parameter.
Command Syntax
COMParator:SLIMit <low limit>,<high limit>
Query syntax
COMParator:SLIMit?
Return format
<NR3><NL^END
Example 1
COMP:SLIM 0.001, 0.002
Sets the low limit of the secondary parameter in
the comparator to 0.001 and the high limit to
0.002.
Where,
<low limit> is the low limit in NR1, NR2 or NR3 data format.
<high limit> is the high limit in NR1, NR2 or NR3 data format.
The low limit should be smaller than the high limit or an error will be issued.
COMParator:Auxiliary BIN
This command is used to set the auxiliary bin as ON or OFF.
Command Syntax
COMParator:AuxiliaryBIN <state>
Query syntax
COMParator:Auxiliary BIN?
Return format
<state><NL^END>
Example 1
COMP:ABIN ON
Turns the Auxiliary bin on.
Where,
<state>: 0 or OFF, or 1 or ON.
COMParator:SWAP
This command is used to set the swap mode ON or OFF. For example: the original function
parameter is Cp-D, after the SWAP mode is set as ON, the function parameter will be changed
as D-Cp. In this case, the limits from BIN1 to BIN9 become the high and the low limits of D, the
original seconday limits become that of Cp. If this function is off, it will not affect the original
measurements.
Command Syntax
COMParator:SWAP <state>
Query syntax
COMParator:SWAP?
Return format
<state><NL^END>
Example 1
COMP:SWAP ON”
Turn the Swap function on.
COMParator:BIN:CLEar
This command is used to clear all limits on Limit Table setup page.
Command Syntax
COMParator:BIN:CLEar
Query syntax
N/A
Return format
N/A
Example 1
COMP:BIN:CLE
Clear the limits on the Limit Table.
COMParator:BIN:COUNt
This command is used to set the bin count function as ON or OFF.
Command Syntax
COMParator:BIN:COUNt <state>
Query syntax
COMParator:BIN:COUNt?
Return format
<NR1><NL^END>
Example 1
COMP:BIN:COUN ON
Sets the count of the bins on.
Where,
<state>: 0 or OFF, or 1 or ON.
COMParator:BIN:COUNt:DATA?
Command Syntax
N/A
Query syntax
COMParator:BIN:COUNt:DATA?
Return format
<BIN1 count>, <BIN2 count>, …, <BIN9 count>,
<OUT OF BIN count>, <AUX BIN count>
<NL^END>
Where,
<BIN1-9 count> is the count result of BIN1-9, in NR1 data format.
<OUT OF BIN count> is the count result of the OUT OF BIN, in NR1 data format.
<AUX BIN count> is the count result of the auxiliary bin, in NR1 data format.
COMParator:BIN:COUNt:CLEar
This command is used to clear all bin count results.
Command Syntax
COMParator:BIN:COUNt:CLEar
Query syntax
N/A
Return format
N/A
Example 1
COMP:BIN:COUN:CLE
Clears all the bin count results.
2.17 Mass MEMory subsystem commands
The Mass MEMory subsystem commands are used for storing and loading files saved in the LCR
meter.
Command tree:
MMEMory:LOAD:STATe
This command is used to load an existing file.
Command Syntax
MMEMory:LOAD:STATe<value>
Query syntax
N/A
Return format
N/A
Example 1
MMEM:LOAD:STAT 1
Where,
<value> is the file number ranging from 0 to 39 (NR1).
MMEMory:STORe:STATe
This command is used to store the current settings of the LCR meter to an internal file.
Command Syntax
MMEMory:STOR:STATe<value>, “<string>”
Query syntax
N/A
Return format
N/A
Example 1
MMEM:STOR:STAT 1, “Resistor meas”
Saves current settings to memory 1, with the
name “Resistor meas”. If there is no
Where,
<value> is the file number ranging from 0 to 39 (NR1).
<string> can be ASCII character string (maximum length is 16). If <string> is no assigned
a name, the default file name will be given to the settings file.
22820 Savi Ranch Parkway
Yorba Linda, CA92887
www.bkprecision.com
© 2017 B&K Precision Corp.
v022117

Navigation menu