Blue Bamboo P25 Bluetooth Printer User Manual

Blue Bamboo (HK) Limited Bluetooth Printer Users Manual

Users Manual

         P25 Installation Guide 1     P25 Bluetooth Printer   Quick Installation Guide
         P25 Installation Guide 2FCC compliance statement “This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” Industry Canada Standard   "This Class (B) digital apparatus complies with Canadian ICES-003."  Cet appareil numérique de la classe (B) est conforme à la norme NMB-003 du Canada.    It is a registered trademark of BLUEBAMBOO   All other trademark is the properties of their respective companies. Certification:  The production has approved by FCC ID: UWJP25   Li-ion Battery has approved  by UN.DOT and CE certification. Power charge has approved by CCC, TUV GS, cULus, CE and FCC certification       Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipmenstatement:
         P25 Installation Guide 31 Unpacking P25 Printer When opening the original shipping carton, carefully inspect the contents. It should include the following items listed below. If any items are damaged or missing, please contact your dealer.            Figure 1: Unpacking P25 Printer
         P25 Installation Guide 42 Installation  2.1 Hardware features  Figure 2: Hardware features 2.2 Inserting the paper roll To install the paper roll in the printer, follow these steps: 1. Open the paper cover by applying your finger pressure to both sides of the printer cover, squeeze to release the lock. 2. Rotate the paper cover up and back. Note that the cover is fixed. It is not necessary to remove it from the printer.
         P25 Installation Guide 5            Figure 3: Open the paper cover 3. Remove the paper roll and insert to a new roll, paper feeds from the bottom and allowing the free paper to extend outside the printer door. 4. Insert the paper roll in the printer as the picture shows:
         P25 Installation Guide 6                                    Figure 4: Install paper roll 5. Press the cover down until it snaps in place. Allow a small amount of paper to extend outside the cover.
         P25 Installation Guide 7                     Figure 5: Pull out a small amount of paper 2.3 Battery supply 2.3.1 Installing/ Removing the battery pack Installing: The battery pack is located at the bottom of the printer. To install it please follow these steps: 1.Remove the isolation film on battery if the battery is a new one. 2.Place the battery pack as shown:
         P25 Installation Guide 8                              Figure 6: Arrow to show the direction 3.Insert the battery pack, and press until it clicks into place. Removal: 1. Release the battery pack by pressing the lock tab.
         P25 Installation Guide 9                        Figure 7: Remove battery 2. Remove the battery pack. 2.3.2 Battery and charge 1.Insert the DC plug of power adaptor into the power jack of printer;   2.Insert the AC plug of power adaptor into AC power supply; 3.Start battery charge, and red LED light continuously; 4.Finish charging, the red LED turn off.                   Figure 8: Battery recharge  Warning: Notice: 1. If the red LED turns on for a short time and then turn off quickly when starting the battery charge procedure, there are two probable reason: first is you have completed battery charging, no need to charge again, second is this battery doesn’t work, please change it. 2. The red LED should turn on during charging and turn off after charging, please care for its status is right or not.
         P25 Installation Guide 103 Using the printer 3.1 Control panel                                                          Buttons z The POWER button switches the power on/off. In order to power off the power, you should press the POWER button for more than 1s. z The FEED button advances the paper roll. Paper is advanced continuously until the button is released. z The Mode button prints the self-test sample paper when pressed together with feed button. z The Feed button enter into boot loader mode when pressed together with power button  LED There is a tricolor LED indicator only:blue, green, red   Constantly lit  Bluetooth module is available Blue Flashing  data transaction via Bluetooth Constantly lit  Power on, normal status Green Flashing  data transaction via USB Constantly lit  Charging Flashing intermittently with Blue LED  An error has occurred Red Off Charging finished  Error description  Remedy  Check Steps  flashing type   There is no more paper  Add paper  1 The paper cover is open  Close the paper cover  2  B,R,B,R…. An transmission error oc-curred  Check the transmission status 3  B,R,R,B,R,R…. An overheat error occurred  Wait until the print head cools down 4  B,R,R,R,B,R,R,R…. Battery voltage is too low  Charge the battery  5  B,R,R,R,R,B,R,R,R,R….
         P25 Installation Guide 11Version History Version  Author  Date  Description 1.0     Initial Version 1.1  Simon  2006-12-19  Modified 3.1, the part of LED

Navigation menu