Blue Bamboo P25 Bluetooth Printer User Manual
Blue Bamboo (HK) Limited Bluetooth Printer Users Manual
Users Manual
P25 Installation Guide P25 Bluetooth Printer Quick Installation Guide http://www.bluebamboo.com P25 Installation Guide FCC compliance statement “This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.” Industry Canada Standard "This Class (B) digital apparatus complies with Canadian ICES-003." Cet appareil numérique de la classe (B) est conforme à la norme NMB-003 du Canada. statement: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipmen It is a registered trademark of BLUEBAMBOO All other trademark is the properties of their respective companies. Certification: The production has approved by FCC ID: UWJP25 Li-ion Battery has approved by UN.DOT and CE certification. Power charge has approved by CCC, TUV GS, cULus, CE and FCC certification http://www.bluebamboo.com P25 Installation Guide 1 Unpacking P25 Printer When opening the original shipping carton, carefully inspect the contents. It should include the following items listed below. If any items are damaged or missing, please contact your dealer. Figure 1: Unpacking P25 Printer http://www.bluebamboo.com P25 Installation Guide 2 Installation 2.1 Hardware features Figure 2: Hardware features 2.2 Inserting the paper roll To install the paper roll in the printer, follow these steps: 1. Open the paper cover by applying your finger pressure to both sides of the printer cover, squeeze to release the lock. 2. Rotate the paper cover up and back. Note that the cover is fixed. It is not necessary to remove it from the printer. http://www.bluebamboo.com P25 Installation Guide Figure 3: Open the paper cover 3. Remove the paper roll and insert to a new roll, paper feeds from the bottom and allowing the free paper to extend outside the printer door. 4. Insert the paper roll in the printer as the picture shows: http://www.bluebamboo.com P25 Installation Guide Figure 4: Install paper roll 5. Press the cover down until it snaps in place. Allow a small amount of paper to extend outside the cover. http://www.bluebamboo.com P25 Installation Guide Figure 5: Pull out a small amount of paper 2.3 Battery supply 2.3.1 Installing/ Removing the battery pack Installing: The battery pack is located at the bottom of the printer. To install it please follow these steps: 1.Remove the isolation film on battery if the battery is a new one. 2.Place the battery pack as shown: http://www.bluebamboo.com P25 Installation Guide Figure 6: Arrow to show the direction 3.Insert the battery pack, and press until it clicks into place. Removal: 1. Release the battery pack by pressing the lock tab. http://www.bluebamboo.com P25 Installation Guide Figure 7: Remove battery 2. Remove the battery pack. 2.3.2 Battery and charge 1.Insert the DC plug of power adaptor into the power jack of printer; 2.Insert the AC plug of power adaptor into AC power supply; 3.Start battery charge, and red LED light continuously; 4.Finish charging, the red LED turn off. Figure 8: Battery recharge Warning: Notice: 1. If the red LED turns on for a short time and then turn off quickly when starting the battery charge procedure, there are two probable reason: first is you have completed battery charging, no need to charge again, second is this battery doesn’t work, please change it. 2. The red LED should turn on during charging and turn off after charging, please care for its status is right or not. http://www.bluebamboo.com P25 Installation Guide 3 Using the printer 3.1 Control panel Buttons The POWER button switches the power on/off. In order to power off the power, you should press the POWER button for more than 1s. The FEED button advances the paper roll. Paper is advanced continuously until the button is released. The Mode button prints the self-test sample paper when pressed together with feed button. The Feed button enter into boot loader mode when pressed together with power button LED There is a tricolor LED indicator only:blue, green, red Blue Constantly lit Flashing Green Constantly lit Flashing Red Constantly lit Flashing intermittently with Blue LED Off Error description Remedy Bluetooth module is available data transaction via Bluetooth Power on, normal status data transaction via USB Charging An error has occurred Charging finished Check Steps There is no more paper Add paper The paper cover is open Close the paper cover An transmission error oc- Check the transmission curred status An overheat error occurred Wait until the print head cools down Battery voltage is too low Charge the battery 10 http://www.bluebamboo.com flashing type B,R,B,R…. B,R,R,B,R,R…. B,R,R,R,B,R,R,R…. B,R,R,R,R,B,R,R,R,R…. P25 Installation Guide Version History Version Author Date 1.0 1.1 Description Initial Version Simon 2006-12-19 Modified 3.1, the part of LED 11 http://www.bluebamboo.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Modify Date : 2007:02:05 09:38:25+08:00 Create Date : 2007:02:05 09:38:25+08:00 Author : huian.gao Page Count : 11 XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:0dcae788-24ab-4be1-bd5d-e7cc6c099966 Producer : Acrobat Distiller 6.0.1 (Windows) Creator Tool : PScript5.dll Version 5.2 Document ID : uuid:3a3556ee-4694-40f4-bc23-9e9b20f8b62d Format : application/pdf Title : Microsoft Word - P25 quickly installation guide 1219.doc Creator : huian.gaoEXIF Metadata provided by EXIF.tools