Broadcom BRCM1002-H 802.11b WLAN Mini-PCI Module User Manual HP Notebook Series Reference Guide

Broadcom Corporation 802.11b WLAN Mini-PCI Module HP Notebook Series Reference Guide

CRN 10069 Q2 HP CRVSA 02T1 75 user manual

HP Notebook PCReference Guide
ii Reference GuideNoticeThis manual and any examples contained herein are provided “as is” and are subjectto change without notice. Hewlett-Packard Company makes no warranty of any kindwith regard to this manual, including, but not limited to, the implied warranties ofmerchantability and fitness for a particular purpose. Hewlett-Packard Co. shall not beliable for any errors or for incidental or consequential damages in connection withthe furnishing, performance, or use of this manual or the examples herein.© Copyright Hewlett-Packard Company 2003. All rights reserved.Reproduction, adaptation, or translation of this manual is prohibited without priorwritten permission of Hewlett-Packard Company, except as allowed under thecopyright laws.The programs that control this product are copyrighted and all rights are reserved.Reproduction, adaptation, or translation of those programs without prior writtenpermission of Hewlett-Packard Co. is also prohibited.Portions of the programs that control this product may also be copyrighted byMicrosoft Corporation, Phoenix Technologies, Ltd., ATI Technologies Inc., IntelCorporation, and Adobe Systems Incorporated. See the individual programs foradditional copyright notices.This product incorporates copyright protection technology that is protected bymethod claims of certain U.S. patents and other intellectual property rights owned byMacrovision Corporation and other rights owners. Use of this copyright protectiontechnology must be authorized by Macrovision Corporation and is intended for homeand other limited viewing uses only unless otherwise authorized by MacrovisionCorporation. Reverse engineering or disassembly is prohibited.Microsoft®, MS-DOS®, and Windows® are U.S. registered trademarks of MicrosoftCorporation. Pentium® and the Intel Inside logo are U.S. registered trademarks andCeleron™ and SpeedStep™ are U.S. trademarks of Intel Corporation. Adobe® andAcrobat® are trademarks of Adobe Systems Incorporated.Reference GuideSecond Edition (March 2003)Part Number: 311074-002
Reference Guide iiiImportant Safety InformationCAUTION To reduce the risk of fire, use only No. 26 AWG or larger telecommunicationsline cord to connect a modem to the telephone wall jack. In Australia, thecomputer must be connected to the Telecommunication Network through aline cord that meets the requirements of ACA Technical Standard TS008.When using your notebook computer with a telephone connection, always followbasic safety precautions to reduce the risk of fire, electrical shock, and injury topersons:• Do not use this product with a telephone connection near water (for example,near a bathtub, sink, swimming pool, or in a wet basement).• Avoid using a telephone connection (other than a cordless type) during anelectrical storm. There may be a remote risk of electrical shock from lightning.• Do not use a telephone connection to report a gas leak in the vicinity of the leak.• Use only the power cord and batteries indicated in this guide. Do not dispose ofbatteries in a fire. They may explode. Check with local codes for possible specialdisposal instructions.• Disconnect the modem cable before opening the computer case or touching anuninsulated modem cable, jack, or internal component.• Do not plug a modem cable or telephone cable into the network (LAN)receptacle.
iv Reference GuideHP Software Product License AgreementYour HP product contains software programs. CAREFULLY READ THISLICENSE AGREEMENT BEFORE PROCEEDING TO OPERATE THISEQUIPMENT. RIGHTS IN THE SOFTWARE ARE OFFERED ONLY ON THECONDITION THAT THE CUSTOMER AGREES TO ALL TERMS ANDCONDITIONS OF THE LICENSE AGREEMENT. PROCEEDING TO OPERATETHE EQUIPMENT INDICATES YOUR ACCEPTANCE OF THESE TERMSAND CONDITIONS. IF YOU DO NOT AGREE WITH THE TERMS OF THELICENSE AGREEMENT, YOU MUST NOW EITHER REMOVE THESOFTWARE FROM YOUR HARD DRIVE AND DESTROY THE MASTERDISKETTES, OR RETURN THE COMPLETE HP PRODUCT AND SOFTWAREFOR A FULL REFUND. PROCEEDING WITH CONFIGURATION SIGNIFIESYOUR ACCEPTANCE OF THE LICENSE TERMS.UNLESS OTHERWISE STATED BELOW, THIS HP SOFTWARE LICENSEAGREEMENT SHALL GOVERN THE USE OF ALL SOFTWARE THAT ISPROVIDED TO YOU AS PART OF THE HP PRODUCT AND SHALLSUPERSEDE ANY OTHER SOFTWARE WARRANTY STATEMENT THATMAY BE INCLUDED IN THIS HP PRODUCT OR MAY BE FOUND ONLINE.Operating system and software applications by Microsoft are licensed to you underthe Microsoft License Agreement contained in the Microsoft documentation ordisplayed on your screen when Microsoft Software Products are launched.For a PC supplied with a Microsoft operating system: When you start the PC andaccept the Microsoft End-user License Agreement (“EULA”), your license rights arevalid only if a Certificate of Authenticity (“COA”) label corresponding to yourMicrosoft operating system is provided with your PC. The COA label can usually befound on the bottom of the computer. If the COA label does not correspond to yourMicrosoft operating system or is missing, contact your HP reseller for details.Other non-HP Software and Operating Systems are covered by the appropriatevendor license. The following License Terms govern the use of the HP software:USE. Customer may use the software on any one HP product. Customer may notnetwork the software or otherwise use it on more than one HP product. Customermay not reverse assemble or decompile the software unless authorized by law.COPIES AND ADAPTATIONS. Customer may make copies or adaptations of thesoftware (a) for archival purposes or (b) when copying or adaptation is an essentialstep in the use of the software with an HP product so long as the copies andadaptations are used in no other manner.
Reference Guide vOWNERSHIP. Customer agrees that he/she does not have any title or ownership ofthe software, other than ownership of the physical media. Customer acknowledgesand agrees that the software is copyrighted and protected under the copyright laws.Customer acknowledges and agrees that the software may have been developed by athird party software supplier named in the copyright notices included with thesoftware, who shall be authorized to hold the Customer responsible for any copyrightinfringement or violation of this Agreement.PRODUCT RECOVERY CD-ROM OR DVD. If your HP product was shipped witha product recovery CD-ROM or DVD: (i) The product recovery CD-ROM or DVDand/or support utility software may only be used for restoring the hard disk of the HPproduct with which the product recovery CD-ROM or DVD was originally provided.(ii) The use of any operating system software by Microsoft contained in any suchproduct recovery CD-ROM or DVD shall be governed by the Microsoft LicenseAgreement.TRANSFER OF RIGHTS IN SOFTWARE. Customer may transfer rights in thesoftware to a third party only as part of the transfer of all rights and only if Customerobtains the prior agreement of the third party to be bound by the terms of thisLicense Agreement. Upon such a transfer, Customer agrees that his/her rights in thesoftware are terminated and that he/she will either destroy his/her copies andadaptations or deliver them to the third party.SUBLICENSING AND DISTRIBUTION. Customer may not lease, sublicense thesoftware, or distribute copies or adaptations of the software to the public in physicalmedia or by telecommunication without the prior written consent of Hewlett-Packard.TERMINATION. Hewlett-Packard may terminate this software license for failure tocomply with any of these terms provided Hewlett-Packard has requested Customer tocure the failure and Customer has failed to do so within thirty (30) days of suchnotice.UPDATES AND UPGRADES. Customer agrees that the software does not includeupdates and upgrades which may be available from Hewlett-Packard under aseparate support agreement.EXPORT CLAUSE. Customer agrees not to export or re-export the software or anycopy or adaptation in violation of the U.S. Export Administration regulations orother applicable regulation.
vi Reference GuideU.S. GOVERNMENT RESTRICTED RIGHTS. Use, duplication, or disclosure issubject to HP standard commercial license terms and for non-DOD Departments andAgencies of the U.S. Government, the restrictions set forth in FAR 52.227-19(c)(1-2)(June 1987) Hewlett-Packard Company, 3000 Hanover Street, Palo Alto, CA 94304U.S.A. Copyright (c) 2000 Hewlett-Packard Company. All Rights Reserved.Customer further agrees that Software is delivered and licensed as “Commercialcomputer software” as defined in DFARS 252-227-7014 (June 1995) or as a“commercial item” as defined in FAR 2.101(a), or as “Restricted computer software”as defined in FAR 52.227-19 (or any equivalent agency regulation or contractclause), whichever is applicable. The Customer agrees that it has only those rightsprovided for such Software by the applicable FAR or DFARS clause or the HPstandard software agreement for the product involved.SUPPORT POLICY FOR MICROSOFT OPERATING SYSTEMS SERVICEPACK. HP will provide end user support for HP PCs that use Microsoft OperatingSystems, including its latest service packs. This support will be available 30 daysafter the service pack being released by Microsoft.
Reference Guide viiContentsGetting Started with Your Notebook .......................................................................1Identifying Parts of the Notebook ..........................................................................2Front panel and right panel components...........................................................2Left panel and back panel components.............................................................4Bottom panel components ................................................................................6Status lights.......................................................................................................8Setting Up Your Notebook...................................................................................10Step 1: Insert the battery.................................................................................10Step 2: Connect AC power .............................................................................11Step 3: Connect a phone line ..........................................................................12Step 4: Turn on the notebook .........................................................................13Step 5: Set up Windows..................................................................................13Basic Operation ........................................................................................................15Operating Your Notebook....................................................................................16Default power settings ....................................................................................16To reset the notebook......................................................................................17To change the boot device ..............................................................................17To use the TouchPad ......................................................................................18To use the function hot keys...........................................................................19To use the One-Touch buttons........................................................................20To use the Windows and Applications keys...................................................21To use the ALT GR key .................................................................................21Using CDs or DVDs.............................................................................................22To insert or remove a CD or DVD .................................................................22To play DVD movies......................................................................................23To create or copy CDs ....................................................................................23Securing Your Notebook......................................................................................24To set up password protection ........................................................................24To lock your notebook....................................................................................24To attach a security cable ...............................................................................25To protect against viruses ...............................................................................25To lock the hard drive.....................................................................................26
viii Reference GuideTaking Care of Your Notebook............................................................................27To protect your hard drive ..............................................................................27To maintain your notebook.............................................................................27To safeguard your data ...................................................................................28To extend the life of the display .....................................................................28To clean your notebook ..................................................................................28Batteries and Power Management..........................................................................29Managing Power Consumption............................................................................30How the notebook manages power automatically..........................................30Using Battery Power.............................................................................................32To check battery status ...................................................................................32To respond to a low-battery warning..............................................................33To recharge the battery ...................................................................................33To get the most from your batteries................................................................34Modem and Network Connections .........................................................................35Using the Modem .................................................................................................36To connect the modem....................................................................................37To change your modem settings.....................................................................38Connecting to a Local Area Network (LAN).......................................................39Making Wireless Network Connections (select models only).............................40To prepare for connections .............................................................................40To turn wireless communication on and off...................................................42Making Wireless Bluetooth Connections (select models only) ...........................44To turn Bluetooth communication on and off ................................................44To prepare for Bluetooth connections ............................................................45To send or receive files using Bluetooth ........................................................46Add-On Devices ........................................................................................................47Connecting PC Cards ...........................................................................................48To insert or remove a PC Card .......................................................................48Connecting External Devices ...............................................................................50To connect an audio device ............................................................................50To use an external monitor .............................................................................52To connect an IEEE 1394 device (select models only)..................................53To connect an infrared device (select models only).......................................54To use a port replicator (select models only) .................................................55Installing Additional RAM (Memory) .................................................................58To install a RAM expansion module..............................................................58To remove a RAM expansion module............................................................60
Reference Guide ixReplacing the Hard Drive.....................................................................................62To replace the hard drive ................................................................................62To replace the hard drive holder.....................................................................63To prepare a new hard drive ...........................................................................64Troubleshooting and Maintenance.........................................................................65Troubleshooting Your Notebook..........................................................................66Audio problems ..............................................................................................66CD-ROM and DVD problems........................................................................67Display problems............................................................................................68Hard drive problems .......................................................................................69Heat problems.................................................................................................70Infrared problems............................................................................................70Keyboard and pointing device problems........................................................71Local area network (LAN) problems..............................................................72Memory problems...........................................................................................73Modem problems............................................................................................73PC Card problems...........................................................................................76Performance problems....................................................................................76Power and battery problems ...........................................................................77Printing problems............................................................................................79Serial, parallel, and USB problems ................................................................80Startup problems.............................................................................................81Wireless problems ..........................................................................................82Configuring Your Notebook ................................................................................84To run the BIOS Setup utility.........................................................................84To change video memory settings using BIOS Setup utility .........................87Reinstalling and Updating Software.....................................................................88To replace a damaged QuickRestore System Recovery CD............................88Reference Information.............................................................................................89Modem Reference Information ............................................................................90Modem Reference (Conexant)........................................................................90Safety Information................................................................................................97Power cords ....................................................................................................97Battery safety..................................................................................................98Laser safety.....................................................................................................98LED safety......................................................................................................99Mercury safety................................................................................................99Exposure to radio frequency radiation..........................................................100
x Reference GuideRegulatory Information ......................................................................................101U.S.A. ...........................................................................................................101Canada ..........................................................................................................103European Union............................................................................................104Japan .............................................................................................................106New Zealand.................................................................................................107Russia............................................................................................................108International..................................................................................................108Index ........................................................................................................................111
Reference Guide 1Getting Started with Your Notebook
Getting Started with Your NotebookIdentifying Parts of the Notebook2 Reference GuideIdentifying Parts of the NotebookComponents included with the notebook vary by geographical region and featuresselected. The following illustrations identify the standard external componentsincluded with most notebook models.Find the illustrations that match your notebook to identify your components.Front panel and right panel components1Notebook open/close latch2One-Touch buttons3Keyboard status lights4Power button: turns the notebook on and off5TouchPad, scroll pad, Click buttons, and anon-off button6Main status lights (left to right): power mode,hard drive activity, and battery7Hard drive8Infrared port (select models only)9Wireless on-off button and indicator light(select models only)10 Battery11 CD-ROM, DVD, or other drive12 PS/2 port
Getting Started with Your NotebookIdentifying Parts of the NotebookReference Guide 31Notebook open/close latch2One-Touch buttons3Keyboard status lights4Power button: turns the notebook on and off5TouchPad, scroll pad, Click buttons, pluson-off button6Main status lights (left to right): power mode,hard drive activity, and battery7Infrared port (select models only)8Wireless on-off button and indicator light(select models only)9Battery10 Audio mute button, audio mute light, andvolume control11 Audio jacks (left to right): audio out(headphones), external microphone12 CD-ROM, DVD, or other drive13 Universal serial bus port (USB)
Getting Started with Your NotebookIdentifying Parts of the Notebook4 Reference GuideLeft panel and back panel components1AC adapter jack2Universal serial bus ports (USB)3RJ-45 jack: connects a network cable4S-Video out jack5Parallel port (LPT1): use this port for a parallelprinter or other parallel device6Serial port (COM1): use this port for a serialmouse, modem, printer, or other serial device7External monitor port8Cable lock slot (security connector)9RJ-11 jack: connects the modem cable10 PC Card and CardBus slot and button11 IEEE 1394 port (select models only)12 Audio jacks (left to right): external microphone,audio out (headphones)13 Volume control14 Audio mute button and audio mute light15 Diskette drive (select models only)
Getting Started with Your NotebookIdentifying Parts of the NotebookReference Guide 51AC adapter jack2Two USB ports3RJ-45 network jack: connects a networkcable4PS/2 port5Parallel port (LPT1): use this port for aparallel printer or other parallel device6External monitor port7S-Video out jack8Cable lock slot (security connector)9RJ-11 jack: connects a modem cable10 IEEE 1394 port (select models only)11 PC Card and CardBus slot and buttons12 Diskette drive (select models only)
Getting Started with Your NotebookIdentifying Parts of the Notebook6 Reference GuideBottom panel components1Hard drive2Battery latch3RAM (memory) cover4Reset button5Docking port (select models only)6Mini PCI cover (no user parts inside)
Getting Started with Your NotebookIdentifying Parts of the NotebookReference Guide 71Hard drive2Battery latch3Mini PCI cover (no user parts inside)4RAM (memory) cover5Docking port (select models only)6Reset button
Getting Started with Your NotebookIdentifying Parts of the Notebook8 Reference GuideStatus lightsThe notebook includes a number of status lights that report power and battery status,drive activity, and keyboard functions such as Caps Lock and Num Lock.The following diagram shows the main status lights on the front of the notebook.1Powermode• On—notebook is on (even if the display is off)• Blinking—notebook is in Standby• Off—notebook is off or in Hibernation2 Hard drive activityOn—notebook is accessing the hard drive3 Battery status• Green—AC adapter is connected and the battery is fully charged• Amber—AC adapter is connected and the battery is charging• Blinking—AC adapter is connected and the battery is missing or has a fault• Off—AC adapter is not connected
Getting Started with Your NotebookIdentifying Parts of the NotebookReference Guide 9The keyboard status lights, located above the keyboard, indicate the states of thekeyboard locks.1 Caps Lock On. Caps Lock is active.2NumLockOn.Num Lock is active. (The Keypad Lock must also be on to usethe embedded keypad.)3 KeypadLockOn.The embedded keypad is active (Fn+F8). Num Lock mustalso be for the numeric keys. Otherwise, cursor control is active (as marked on anexternal keyboard).
Getting Started with Your NotebookSetting Up Your Notebook10 Reference GuideSetting Up Your NotebookWARNING Improper use of keyboards and other input devices has been associated withergonomic injury.If you are using your notebook as your primary computer, or using it forextended periods, you should use it with a full-sized keyboard, monitor, andmouse. Docking accessories offer quick, easy connections to these devices. Thiscan reduce the risk of ergonomic injury.For information about reducing your risk, see the Safety & Comfort Guide onthis CD included with your notebook.When you set up your notebook for the first time, you will charge the battery,connect the AC adapter, turn on the notebook, and run the Windows setup program.Step 1: Insert the batteryWARNING Do not mutilate or puncture batteries. Do not dispose of batteries in fire, orthey can burst or explode, releasing hazardous chemicals. Rechargeablebatteries must be recycled or disposed of properly.Your notebook is shipped with the battery installed. If the battery has been removed,you should install it:1. Turn the notebook upside down.2. Insert the connector end of the battery into the battery compartment, then slidethe battery in until it latches.
Getting Started with Your NotebookSetting Up Your NotebookReference Guide 11Step 2: Connect AC powerCAUTION Use only the AC adapter included with your notebook (or other approvedadapter that meets the power requirements of the notebook).Using the wrong AC adapter could damage the notebook or adapter or causedata loss and may void your warranty.1. Plug the AC adapter into the notebook.2. Connect the power cord to the AC adapter.3. Plug the power cord into a wall outlet. The notebook battery starts charging.Important When unplugging the power cord, unplug it from the wall outlet before unpluggingit from the AC adapter.While the battery is charging, you can continue with the “Step 3: Connect a phoneline” section.
Getting Started with Your NotebookSetting Up Your Notebook12 Reference GuideStep 3: Connect a phone line1. Make sure the telephone line is an analog line, sometimes called a data line.(Do not use a digital line.)2. Connect the telephone cord (RJ-11) into a telephone jack.3. Plug the other end of the telephone cord into the RJ-11 modem jack on thenotebook.For details about using the modem, see “Using the Modem” later in this guide.
Getting Started with Your NotebookSetting Up Your NotebookReference Guide 13Step 4: Turn on the notebookPress the power button above the left side of the keyboard. The notebook boots upand Windows starts automatically.Hint If your notebook does not turn on when operating on battery power, the battery maybe out of power. Plug in the AC adapter, then press the power button again. Leavethe AC adapter plugged in for several hours to fully charge the battery. Chargetimes will vary.Step 5: Set up WindowsYour notebook has the Microsoft Windows operating system preinstalled on its harddrive. The first time you turn on your notebook, the Windows Setup program runsautomatically so you can customize your setup.1. Follow the Setup program instructions on the screen. If the program prompts youto enter the Product ID code, locate the code on the bottom of the notebook.2. Check the modem country or region settings. Select Start > Control Panel >Printers and Other Hardware > Phone and Modem Options, then choose yourcountry or region.
Reference Guide 15Basic Operation
Basic OperationOperating Your Notebook16 Reference GuideOperating Your NotebookYou can start and stop your notebook using its power button. However, at certaintimes you may want to use other methods to start or stop the notebook—dependingon power considerations, types of active connections, and startup time.Default power settingsPower mode To enter this mode FunctionON—Power statuslight will turn on.Briefly press the power button. Powers on the notebook.OFF—Power statuslight will turn off.Select Start > Turn Off Computer > Turn Off.If the system has stopped responding andWindows shutdown procedures cannot be used,press and hold the power button for at least4 seconds to turn off the notebook.Powers off the notebook.Standby—Powerstatus light will blink.Select Start > Turn Off Computer > Stand By.–or–Allow the system to time out.• Saves significant power.• Turns off the display andother components.• Maintains current sessionin RAM.• Restarts quickly.• Restores networkconnections.Hibernation—Power status lightwill turn off.If the unit is already on, briefly press the powerbutton.–or–Press Fn+F12.–or–Allow the system to time out.• Saves maximum power.• Saves current session todisk, then shuts down.• Restores networkconnections.You can also customize the way these power modes work. See the “Batteries andPower Management” chapter in this guide.
Basic OperationOperating Your NotebookReference Guide 17To reset the notebookOccasionally, you may find that Windows or the notebook has stopped respondingand will not let you turn the notebook off. If this happens, try the followingprocedures in this order:• If possible, shut down Windows. Press CTRL+ALT+DEL, then select ShutDown, Restart.–or–• Press and hold the power button for at least 4 seconds until the display shutsdown. Any unsaved data will be lost. Then press the power button again torestart.–or–• Insert the tip of a paper clip into the reset button on the bottom of the notebook,then press the power button to restart.To reset the notebook while it is docked in a port replicator, you can press the resetbutton on the left side of the port replicator.To change the boot deviceThe notebook normally boots from its internal hard drive. You can also bootthe notebook from a diskette drive, a CD-ROM drive, or an internal networkinterface card.1. Select Start > Turn Off Computer > Restart.2. When the logo screen appears, press ESC to display the Boot menu.3. Use the arrow keys to select the boot device, then press ENTER.If you want to boot from a specific device whenever it is present, change the bootorder using the BIOS Setup utility. See “Configuring Your Notebook” in the“Troubleshooting and Maintenance” chapter in this guide.
Basic OperationOperating Your Notebook18 Reference GuideTo use the TouchPadThe TouchPad includes an on-off button so you can turn off the TouchPad to avoidmoving the pointer accidentally, such as by touching the pad while typing. Theindicator light turns off when you turn off the TouchPad.1 Click buttons. The Click buttons work like the left andright buttons on a standard mouse.2TouchPad(touch-sensitive pointing device).3 TouchPad on-off button and indicator light.4 Scroll pad. The scroll pad scrolls vertically to display thecontents of the active window.
Basic OperationOperating Your NotebookReference Guide 19To use the function hot keysThe combination of the Fn key plus another key creates a hot key—a shortcut keysequence—for various system controls. To use a hot key, press and hold Fn, pressthe appropriate second key, then release both keys.This hot key Does thisFn+F1 Decreases the display brightness.Fn+F2 Increases the display brightness.Fn+F8 Toggles the built-in keypad on and off. Does not affectan external keyboard. If Num Lock is on, then thenumeric functions are active. Otherwise, cursor controlis active (as marked on an external keyboard).Fn+F12 Enters Hibernation.Fn+NumLock Toggles Scroll Lock on and off.Fn+Page Up Increases the audio volume and cancels the mutesetting.Fn+Page Down Decreases the audio volume.Fn+Backspace Mutes/unmutes the audio output.
Basic OperationOperating Your Notebook20 Reference GuideTo use the One-Touch buttonsYour notebook includes five One-Touch buttons that can start any application oropen a document or Web site with a single press.Press a One-Touch button to open the corresponding application, document, orWeb site.To program a One-Touch button1. Select Start > All Programs > Utilities > One Touch.2. On the One-Touch tab, select the button you want to reprogram.3. Type a label for the button, then select the application, document, folder, orWeb site you want the button to open.4. If you want a label to appear onscreen when you press a One-Touch button,select that option on the Onscreen Display tab.
Basic OperationOperating Your NotebookReference Guide 21To use the Windows and Applications keysThe Windows key brings up the Windows Start menu. This is the same as selectingthe Start button on the taskbar.The Applications key brings up the shortcut menu for the selected item. This is thesame menu that appears when you right-click while pointing at the selected item.This key combination Does thisWindows key+E Runs Windows ExplorerWindows key+F1 Runs Windows HelpWindows key+F Runs Windows Find: SearchWindows key+M Minimizes all displayed windowsShift+Windows key+M Returns all minimized windows to original sizeWindows key+R Runs the Windows Run dialog boxTo use the ALT GR keyNon-U.S. keyboards have an ALT GR key to the right of the spacebar. This is a shiftkey that provides access to certain special keyboard characters.For a character in the lower-left corner of a key, press and hold ALT GR to type thecharacter.1Shifted2Unshifted3ALT GR
Basic OperationUsing CDs or DVDs22 Reference GuideUsing CDs or DVDsTo insert or remove a CD or DVDCAUTION Do not remove a CD or DVD while the notebook is reading it. Otherwise, thenotebook could stop responding and you could lose data.Press the CD or DVD gently, but firmly, onto the spindle to avoid damage tothediskordrive.1. Press the button on the face of the CD or DVD drive. If you are using this drivefor the first time, be sure to remove the cardboard packing insert if present.2. Place the CD or DVD into the drive (label facing up), then gently press down toseat it on the spindle.–or–Remove the CD or DVD.3. Slide the tray back into the module to close it.If your notebook loses power, you can manually open the drive to remove a CD.Insert a straightened paper clip into the recessed hole on the front of the drive toopen it.The location of the CD or DVD drive varies by model.
Basic OperationUsing CDs or DVDsReference Guide 23To play DVD moviesIf your notebook is equipped with a DVD or other DVD readable drive, it alsoincludes a DVD player software that lets you play DVD movies.Select Start > All Programs > Multimedia > DVD Player > InterVideo WinDVD.Hint For best performance while playing movies on battery power, set the Control Panelpower scheme to Portable/Laptop.Important DVDs can have regional codes embedded in the disc data. These codes preventDVD movies from being played outside the region of the world in which they aresold. If you get a region code error, you are trying to play a DVD intended for adifferent region.Most DVD drives let you change the region code only a limited number of times(usually no more than four). When you reach this limit, your last change to theregion code will be hard-coded on the DVD drive, and will be permanent. Yourwarranty does not cover the expense of correcting this situation. Refer to the Helpfor your DVD player software for details about setting region codes.To create or copy CDsIf your notebook is equipped with a DVD/CD-RW combo drive, it also includessoftware such as Roxio Easy CD Creator that lets you copy or create CDs. Followthe instructions that are included with the software. Read and write quality may varyby media.
Basic OperationSecuring Your Notebook24 Reference GuideSecuring Your NotebookTo set up password protectionYou can protect your notebook from access by another user when you set uppassword protection, which is available through Windows and through the BIOSSetup utility. See “Configuring Your Notebook” in the “Troubleshooting andMaintenance” chapter. For complete protection, set passwords in Windows as wellas through BIOS Setup.To cancel password protection, set an empty password.Windows1. Select Start > Control Panel > User Accounts, then select your account.2. Select Create a Password, then set the password.3. Select Start > Control Panel > Performance and Maintenance > Power Options.4. On the Advanced tab, select the option to prompt for a password when thenotebook leaves Standby.To lock your notebookTo protect against unauthorized access while your notebook is running, lock thenotebook before leaving it unattended, or set up a screen saver with a Windowspassword. You can lock the notebook these ways:• If a One-Touch button is assigned to Quick Lock, press that button.–or–• Press CTRL+ALT+DEL, then select Lock Computer.To unlock the notebook, follow your normal logon steps.
Basic OperationSecuring Your NotebookReference Guide 25To attach a security cableYour notebook includes a built-in connector to secure the notebook with a cable anda lock (such as the Kensington MicroSaver lock system, available at many computerstores).1Wrap the cable around a secure object, such as a table leg.2Insert the cable into the security cable slot on the notebook.3Lock it with the cable lock key, then store the key in a safe place away from thenotebook.To protect against virusesVirus-protection software can help protect the integrity of your data. This isespecially important if you use the Web.Your notebook comes equipped with the Norton AntiVirus software. You can getdetailed instructions from the Norton online Help. Because new viruses appearfrequently, you will also want to update the program virus definitions periodically.Norton AntiVirus updates are on the Web at www.symantec.com.
Basic OperationSecuring Your Notebook26 Reference GuideTo lock the hard driveThe notebook enables you to lock its internal hard drive to help keep yourinformation secure. Hard drive lock does not protect a second hard drive installed inthe module bay.CAUTION When you enable hard drive lock, the current BIOS user password (oradministrator password if that is the only password set) is encoded on the harddrive.If you move the hard drive to another computer, you can’t access the drive untilyou set the user (or administrator) password to match the drive password. Afteryou match the drive password, you can change the computer (and drive)password. If you forget the password, you cannot recover your data.1. Select Start > Turn Off Computer > Restart.2. When the logo screen appears, press F2 to enter the BIOS Setup utility.3. From the Security menu, enable Password Required to Boot.4. From the Security menu, enable Internal hard drive lock.5. Press F10 to save and exit BIOS Setup.
Basic OperationTaking Care of Your NotebookReference Guide 27Taking Care of Your NotebookUse the following recommendations to maintain your notebook during everyday useand prevent potential physical damage or data loss.To protect your hard driveHard drives, as well as other internal components, are not indestructible and can bedamaged by inappropriate handling and operation.• Avoid bumps or jolts.• Do not operate the notebook while traveling over bumpy terrain.• Put the notebook in standby or shut it down before transporting it. This turns offthe hard drive. A drop of a few inches onto a rigid surface while the hard drive isoperating could destroy data or damage the drive.• Carry the notebook in a padded case to protect against bumps and jolts.• Set down the notebook gently.To maintain your notebook• Provide adequate ventilation around the notebook. Always set the notebook on aflat surface, so that air can flow freely around and underneath it.• Always shut down the notebook or put it in Hibernation before putting it in acarrying case or other enclosed space.• Do not pick up or carry the notebook by its display.• Do not use the notebook outside in the rain or snow (inclement weather). If thenotebook is cold, warm it gradually to avoid condensation.• Maintain your battery for best performance. See the “Batteries and PowerManagement” chapter.
Basic OperationTaking Care of Your Notebook28 Reference GuideTo safeguard your data• Do not use a pointing device or activate any other device that interrupts operationwhile the system is starting or stopping.• Back up your work regularly. Copy files to diskettes, CDs, DVDs, and othermedia or network drives.• Use a virus-scanning program (such as the Norton AntiVirus program includedwith your notebook) to check the integrity of your files and operating system.• Check your disk using the Tools tab in the disk Properties window.To extend the life of the display• Set the display brightness to the lowest comfortable level (Fn+F1).• When working at your desk, connect an external monitor and turn off the internaldisplay (press the TV Now! One-Touch button at the top of the keyboard).• If you are not using an external monitor, set the Turn off monitor timeouts (forboth AC and battery operation) to the shortest comfortable interval.• Avoid using a screen saver or other software that prevents the notebook fromchanging to Display-off or Standby after a timeout period. If you use a screensaver, enable the option to shut off the display after a time delay.• Do not disable Display-off or Standby timeouts.• If you are using AC power and have no external monitor attached, put thenotebook in Standby when not in use.To clean your notebook• You can clean the notebook with a soft cloth dampened with clean water or withwater containing a mild detergent. Do not use an excessively wet cloth, and takecare to keep water out of the case.• Do not use abrasive cleaners, especially on the display. Do not apply any cleanerdirectly to the display. Instead, apply the cleaner to a soft cloth, then gently wipethe display.
Reference Guide 29Batteries and Power Management
Batteries and Power ManagementManaging Power Consumption30 Reference GuideManaging Power ConsumptionWhen you are running your notebook on battery power, you can maximize operatingtime without compromising performance. Your notebook is designed to help youreduce power consumption and extend battery life.During idle periods, the notebook automatically enters power-saving modes afterspecified timeout periods. You can adjust these timeouts to suit your working habits.How the notebook manages power automaticallyYour notebook enters Hibernation and Standby automatically, and turns off the harddrive and display based on values set in Windows.When this occurs The result is To resumeNo keyboard, pointing device, or otherinput activity occurs for the specifiedintervalDisplay turns off.Turns off the display toconserve battery power andextend the life of the display.Briefly press any key ormove a pointing device toturn on the display.The hard drive is not accessed for aspecified intervalHard drive turns off.This is usually set to occurshortly after the display isturned off.Begin using thenotebook, and the harddrive turns on.No pointing devices are used, no diskdrive is accessed, and no port (serial,parallel, or infrared) is active for thespecified intervalStandby is initiated.Maintains your currentsession in RAM, and turns offthe display and othercomponents to conservebattery power.Briefly press the powerbutton to return to yourcurrent session.The notebook stays in Standby for thespecified intervalHibernation is initiated.Saves your current sessionto the hard drive, and turnsoff the notebook.Press the power button toreturn to your previoussession.CAUTION Make a habit of saving your work before allowing your notebook to enterStandby. If power is interrupted while the notebook is in Standby, anyinformation that was not saved will be lost.
Batteries and Power ManagementManaging Power ConsumptionReference Guide 31The notebook can also enter Hibernation if battery power reaches a critically lowlevel. If this happens, you will find on resuming that all your data has been saved,but some functions may be disabled. To resume normal operation, restore power byconnecting an AC adapter or installing a charged battery, then shut the notebook offand restart it.Changing timeout settings and creating power schemesYou can adjust the length of timeouts after which your notebook automatically shutsdown components or enters a power-saving mode. You can also save these settingsas a power scheme.1. Select Start > Control Panel > Performance and Maintenance > Power Options.2. Select the Power Schemes tab, then enter the settings you want. If you do notwant a particular timeout to occur, set the value to Never. See Windows Help fordetails.If you want to save the settings as a power scheme, select Save As and enter aname for the scheme.CAUTION Do not disable Hibernate support in the Power Options settings, or you will loseany unsaved data if the notebook battery runs down completely.
Batteries and Power ManagementUsing Battery Power32 Reference GuideUsing Battery PowerTo check battery statusFrom the battery status lightCheck your notebook battery status light.From the Windows taskbarThe Windows taskbar can display a power icon that provides detailed battery statusinformation (see Windows Help for details). The icon resembles a battery when ACpower is not connected.• Place the pointer over the power icon to display the remaining battery charge.This value is shown as either a percentage of charge remaining, or as timeremaining.• Select the power icon to open the Battery Meter window.From the Windows Control PanelSelect Start > Control Panel > Performance and Maintenance > Power Options, thenselect the Power Meter tab to see the battery status. The Alarms and Advanced tabsprovide additional Windows power-information options.On the battery1. Remove the battery from the notebook. See the “Getting Started with YourNotebook” chapter in this guide.2. Press the contact pad on the side of the battery. The number of lights that turn onindicates the remaining charge (each light represents 20 percent of a full charge).
Batteries and Power ManagementUsing Battery PowerReference Guide 33To respond to a low-battery warningThe notebook automatically alerts you when the battery power drops to a criticallylow level. The notebook first emits a high-pitched beep or displays a warningmessage. Then, if you do not restore power within a short time, the notebook entersHibernation.After the notebook enters Hibernation in this way, you will not be able to turn it onagain until you restore power by doing one of the following procedures:• Replace the battery with a charged one.• Plug in the AC adapter.Note If you plug in the AC adapter, you can continue to work while your batteryrecharges.To recharge the batteryCAUTION The AC adapter is normally warm whenever plugged into an AC outlet. Thenotebook is normally warm while recharging. Do not recharge the notebook ina briefcase or other confined space, or the battery could overheat.Plug the AC adapter into the notebook.To get the longest operating time, wait until the battery charge is below 50 percentbefore recharging, then charge it fully (100 percent). Charging can take up to severalhours. If you continue working while the battery charges, the charging time mayincrease.The operating time for a fully charged battery depends on the notebook model,power management settings, and level of use.
Batteries and Power ManagementUsing Battery Power34 Reference GuideTo get the most from your batteriesFollow these suggestions to make your battery power last as long as possible:• Plug in the AC adapter, especially when using a CD-ROM or DVD drive, or anyexternal connections such as a PC Card or a modem.• Set the display brightness to the lowest comfortable level (Fn+F1).• Put the notebook in Standby whenever you are not using it for a short while.• Put the notebook in Hibernation whenever you want to save your current session,but will not be using the notebook for a day or more.• Set the automatic timeout settings to emphasize saving power. If your notebookhas a multispeed processor, use the lower speed on battery power (the defaultsettings conserve battery power).• If your notebook has a wireless on-off button, turn off the wireless function whenyou are not using it. Press the wireless on-off button so that the light turns off.• If you have a PC Card such as a network card, remove it when you are not usingit. Some PC Cards use significant power even while they are inactive.• If you work with an application that uses the serial port or a PC Card, exit theapplication when you finish using it.• Do not leave batteries unused for long periods. If you have more than one,rotate them.• If you normally use AC power, make a practice of using the battery as yourpower source at least once a week.• Unplug the AC adapter when the notebook is not in use.• To preserve the life of a battery, be sure to charge it regularly.• For long-term storage, the battery must be charged 20 percent to 50 percent tominimize capacity loss by self-discharge and to avoid deterioration of batteryperformance.• Avoid using or charging batteries at high temperatures.
Reference Guide 35Modem and Network Connections
Modem and Network ConnectionsUsing the Modem36 Reference GuideUsing the ModemYou can connect your modem to a telephone line and communicate with othercomputers throughout the world. You can explore the Internet, send and receivee-mail messages, and use your notebook to send and receive faxes. Your notebookcontains several software programs that work with your modem:• Internet Explorer, for browsing the World Wide Web• Outlook Express, for sending and receiving e-mail messages• Windows Fax Console software for sending and receiving faxesFor best performance, you can connect to any Internet Service Provider (ISP) ormodem network that has V.90 or V.92 interoperable modems. Check with yourISP for a list of telephone numbers that support V.90 or V.92. (V.92 enables modemon-hold technology that allows an Internet session to be interrupted to answer aphone call, then resumes the Internet session once the call is complete.)The maximum speed for faxing is 14.4 Kbps, even though the modem is capable ofdownloading at higher speeds.
Modem and Network ConnectionsUsing the ModemReference Guide 37To connect the modemCAUTION Your built-in modem may not work with multiple phone lines or a privatebranch exchange (PBX), cannot be connected to a coin-operated telephone, anddoes not work with party lines. Some of these connections may result in excesselectrical voltage and could cause a malfunction in the internal modem. Checkyour telephone line type prior to connecting your phone line.Special restrictions in certain countries• Many countries impose a blackout period after a modem repeatedly fails toconnect to a service provider. The number of failed attempts and the period youmust wait before trying again differ from country to country. Check with yourtelephone company.For example, if you are dialing from Italy and fail to connect to your server orcancel the connection, you must wait one minute before dialing that numberagain. If you dial before then, you will get an error message that says “delay.”After the fourth failed connection, you must wait one hour before trying thenumber again. If you dial before the hour is up, you will get a message that says“black list.”• When using a modem, an external surge protector can prevent damage to yournotebook from lightning or other electrical surges. Connect any approved surgeprotector to the modem cable when you are using the modem.
Modem and Network ConnectionsUsing the Modem38 Reference GuideTo change your modem settingsThe modem is already set up to be compatible with telephone systems and modemsin most areas. However, in some situations, you may have to change modem settingsto match local conditions. If you have questions about local requirements, contactyour telephone company.• Control Panel. Open Phone and Modem Options in Control Panel to changemany modem settings. On the Modems tab, select Properties to set connectionspeeds, or on the Dialing Rules tab select Edit to set dialing options.• Communications software. Many communications applications provide optionsfor controlling modem settings. See the Help for your software.• AT commands. You can control many aspects of modem operation usingmodem AT commands. AT commands are special strings of characters sent to themodem to set up specific conditions. Those command strings normally start with“AT.” For a list of AT commands for the built-in modem, see the “ReferenceInformation” chapter.Open Phone and Modem Options in Control Panel. On the Modems tab, selectProperties. You can type AT commands on the Advanced tab in the space forextra settings.
Modem and Network ConnectionsConnecting to a Local Area Network (LAN)Reference Guide 39Connecting to a Local Area Network (LAN)LANs give you access to network resources, such as printers and file servers on yourcorporate network, and possibly to the Internet. To connect to a LAN:1. Check that the existing LAN supports Ethernet 10Base-T (10 Mbps) or100Base-TX (100 Mbps) connections.2. Plug the LAN cable (not supplied) into the built-in LAN port. The cable musthave an RJ-45 connector.3. Windows automatically detects and sets up a LAN connection. To edit settings,open Network and Dial-up Connections in Control Panel.See Windows Help for information about setting up and using LAN connections.Select Start > Help and Support. Contact your network administrator for networkinformation.Two lights next to the LAN port indicate the status of the connection:• The yellow light indicates network activity.• The green light indicates a 100 Mbps link.
Modem and Network ConnectionsMaking Wireless Network Connections (select models only)40 Reference GuideMaking Wireless Network Connections (select models only)If your notebook includes a wireless on-off button, you can connect by radio to an802.11 wireless local area network (LAN) and access computers and other resourceson the network.A wireless network provides all the functions of a typical “wired” network, but alsoprovides for “roaming.” Since your notebook connects to the network by radio ratherthan through cables, you can move from place to place within the network—fromyour office to a conference room, for example—and remain on the network theentire time.To prepare for connectionsBefore you can connect your notebook to a particular 802.11 wireless network, youhave to configure the notebook for the specific wireless connection.Connecting to an existing wireless networkYou can connect to an access point that gives you access to a local area network, oryou can connect directly to other computers in an “ad hoc” network.1. Right-click the wireless network connection icon in the taskbar, then select ViewAvailable Wireless Networks from the pop-up menu.
Modem and Network ConnectionsMaking Wireless Network Connections (select models only)Reference Guide 412. A list of available networks appears. Select the network you want, enter theencryption key if required, then select Connect.If the network you want is not on the list, select Advanced > Configure, and enterthe required network parameters. If the network is not using 802.1xauthentication protocol, clear the automatic key option.3. On the General tab, edit network settings as needed for your local network. Seeyour network administrator. You can also display an icon in the taskbar whenconnected to a network.4. On the Wireless Networks tab, view the wireless networks available withinrange. Each network SSID is listed. Select the network you want, then selectConfigure.5. If the wireless network uses standard encrypted communication, uncheck theautomatic key option, then select the following parameters:• Key: ASCII passphrase or hexadecimal key string.• Key format: ASCII for passphrase, hexadecimal for key string.• Key length: smaller number for 64-bit encryption, larger number for 128-bit.See your network administrator for the required settings.6. Select OK to save the configuration. This network is added to your list ofpreferred networks.The notebook automatically connects to the first preferred network within range ifwireless communication is turned on.Creating a New Computer-to-Computer Network (Ad Hoc)You can set up a new network available to other local computers.1. Select Start > Control Panel > Network and Internet Connections > NetworkConnections.2. Select the wireless connection to show its status, then select Properties.3. On the Wireless Networks tab, select Add to create a new network.4. Type a name for the new network.
Modem and Network ConnectionsMaking Wireless Network Connections (select models only)42 Reference Guide5. If you want to use encrypted communication, uncheck the automatic key option,then select the following parameters:• Key: ASCII passphrase or hexadecimal key string• Key format: ASCII for passphrase, hexadecimal for key string• Key length: smaller number for 64-bit encryption, larger number for 128-bit6. Mark the option to make this a computer-to-computer (ad hoc) network.7. Select OK to save the configuration. This network is added to your list ofpreferred networks and becomes available to other computers.To turn wireless communication on and offImportant Wireless networks and cellular modems are examples of devices that use wirelesscommunication. Such devices may be restricted in some situations or environments,such as when traveling in an airplane. If in doubt, be sure to ask for authorizationbefore turning on your notebook wireless networking.In Italy, Singapore, and possibly other countries, you may be required to purchase alicense before using the wireless function.Turning on communication and making a connectionIf your notebook has both wireless 802.11 and Bluetooth capabilities, the wirelessindicator light on the front of the notebook turns on when Bluetooth or 802.11communication is turned on, but it does not show whether Bluetooth, 802.11, or bothfunctions are active. You must use the Wireless Configuration software to control theindividual wireless functions.1. If the notebook is not on, turn it on.2. If you normally press the wireless on-off button on the front of the notebook toturn wireless 802.11 communication on and off, press the button so the indicatorlight turns on. This restores your previous wireless configuration.–or–Select Start > Control Panel > Network and Internet Connections > NetworkConnections, then select the wireless network connection icon.If you are within range of your wireless network, your notebook automaticallyconnects. To check the status of your wireless connection, open NetworkConnections in Control Panel, then select the connection.
Modem and Network ConnectionsMaking Wireless Network Connections (select models only)Reference Guide 43Turning off communication and ending a connection1. Important: close any files that reside on other network computers.2. To turn off the wireless 802.11 communication without turning off the notebook,press the wireless on-off button. This also turns off Bluetooth communication if itwas enabled.–or–Right-click the wireless network connection icon in the taskbar, then selectDisable.Putting the notebook in Standby or shutting it down also turns off the wirelessfunction.
Modem and Network ConnectionsMaking Wireless Bluetooth Connections (select models only)44 Reference GuideMaking Wireless Bluetooth Connections(select models only)If your notebook includes Bluetooth wireless capabilities, you can use it to makeshort-range radio connections to a wireless personal area network (PAN) and accessother Bluetooth-compatible devices, such as other computers, cell phones, andprinters.Since the Bluetooth function connects your notebook by radio rather than throughcables, you can move around and remain connected, and you can detect newBluetooth devices automatically when they enter your area.To turn Bluetooth communication on and offImportant Wireless communication may be restricted in some situations or environments, suchas when traveling in an airplane. If in doubt, be sure to ask for authorization beforeturning on your notebook wireless networking.In Italy, Singapore, and possibly other countries, you may be required to purchase alicense from the responsible authority before using the wireless function.Turning on Bluetooth communicationThe wireless indicator light on the front of the notebook turns on when Bluetooth or802.11 communication is turned on, but it doesn’t show whether Bluetooth, 802.11,or both functions are active. You must use the Wireless Configuration software tocontrol the individual wireless functions.1. If your notebook isn’t on, turn it on.2. If you normally press the wireless on-off button on the front of the notebook toturn Bluetooth communication on and off, press the button so the indicator lightturns on. This restores your previous wireless configuration.–or–If the Wireless Configuration icon is present in the taskbar, select the icon, thenselect the Bluetooth button to turn on Bluetooth communication.
Modem and Network ConnectionsMaking Wireless Bluetooth Connections (select models only)Reference Guide 45Turning off Bluetooth communicationTurning off communication ends any connection you have open.1. Important: close any files that reside on other network computers.2. To turn off Bluetooth communication without turning off your notebook, pressthe wireless on-off button. This also turns off 802.11 communication if it wasenabled.–or–If the Wireless Configuration icon is present in the taskbar, select the icon, thenselect the Bluetooth button to turn off Bluetooth communication, withoutaffecting 802.11 communication.Turning off the notebook or putting it into Hibernation also turns off the Bluetoothfunction.To prepare for Bluetooth connectionsBefore you use your notebook to access other Bluetooth devices, you shouldconfigure some basic settings.1. Make sure Bluetooth communication is turned on.2. Select the Bluetooth icon in the taskbar.3. In the menu bar, select Bluetooth > Device Configuration. (This menu isavailable only while Bluetooth folders are selected.)4. On the General tab, check the following settings:• Give your notebook a unique name that will identify it to other Bluetoothusers.• Set the computer type to Laptop.• Select the security mode you want to use.5. On the Information Exchange tab, check the following settings:• Check the directory you want to make available to other Bluetooth users forsharing files, both sent and received.• Check the directory where you want to store your business card file so youcan easily send it to other Bluetooth users.• Check the inbox directory where you want delivered files from otherBluetooth users to be stored automatically.Detailed information about these and other advanced settings are included in theonline help.
Modem and Network ConnectionsMaking Wireless Bluetooth Connections (select models only)46 Reference GuideTo create your business card, you can open Microsoft Outlook, then open the addressbook and create a new contact. After entering your personal information, select File,Export To vCard File and store the file in your business card directory.To send or receive files using BluetoothIf your notebook includes Bluetooth wireless capabilities, it supports the followingcommon protocols for transferring data. To use either protocol, both computers mustsupport that protocol. Check the other computer’s Bluetooth documentation.• FTP: files can be copied into and out of shared directories (folders) by bothcomputers. This service is equivalent to common network file sharing.• OPP (object push profile): both computers can send certain types of MicrosoftOutlook data to the other computer’s Bluetooth inbox, but cannot retrieve filesfrom the other computer.Sharing files with another Bluetooth device (FTP)1. Select the Bluetooth icon in the taskbar.2. In My Bluetooth Places, select and open the other device to view files in itsshared directory.3. Use Windows Explorer or other software to copy or move files between yournotebook and the other device.Sending Outlook data to another Bluetooth device (OPP)1. Select the Bluetooth icon in the taskbar.2. In My Bluetooth Places, select and open the other device.3. To send a calendar item, note, or message, select the device inbox, select theoption you want, then select the file to send. The file arrives in the device inboxdirectory.–or–To send your business card, select the device inbox, then select the option to sendyour business card.
Reference Guide 47Add-On Devices
Add-On DevicesConnecting PC Cards48 Reference GuideConnecting PC CardsThe notebook PC Card slot is available for storing data and expanding thecommunication capabilities of the notebook. The notebook supports standard Type IIand III PC Cards (PCMCIA and CardBus).To insert or remove a PC CardNote The location and number of the PC Card slots vary by model series.Inserting a PC Card1. Hold the PC Card label-side up with its connectors facing the card slot.2. Slide the PC Card all the way into the bottom of the slot. Most cards are properlyseated when the outer edge is flush with the casing of the notebook, but somecards are designed to protrude from the case.
Add-On DevicesConnecting PC CardsReference Guide 49Removing a PC CardCAUTION Before removing a PC Card, you must use the Eject Hardware or SafelyRemove Hardware icon in the taskbar, or shut down the notebook. Otherwise,you could lose data.1. Before removing the card, select the Eject Hardware or Safely Remove Hardwareicon in the taskbar, then select the card you want to remove. This protects yourdata and helps avoid unexpected problems.If needed, you can restart the card by removing and then reinserting it.2. Press the eject button to pop the button out, then press it in to eject the PC Card.
Add-On DevicesConnecting External Devices50 Reference GuideConnecting External DevicesTo connect an audio deviceYou can plug in an external microphone, external speakers, or headphones. Inaddition, if you connect your notebook to the port replicator, you can plug in a stereosource (such as a CD player) or a device that accepts digital audio (such as a digitalaudio recorder).CAUTION The headphone and line-in jacks are three-terminal stereo jacks. They are notcompatible with two-terminal mono plugs. Connecting a mono plug into eitherof these jacks may damage the notebook.Attach the audio cable to the corresponding audio port on the notebook or portreplicator. Match your notebook to one of the following illustrations to locate theaudio connectors on your notebook.1External microphone connector (pink)2Audio out (headphones) connector (green)
Add-On DevicesConnecting External DevicesReference Guide 511Audio out (headphones) connector (green)2External microphone connector (pink)Note When you plug a device into the headphone port, the built-in speakers automaticallyturn off. When you plug a device into either audio port on the notebook, any deviceconnected to the corresponding port on the port replicator is ignored.
Add-On DevicesConnecting External Devices52 Reference GuideTo use an external monitorConnecting an external monitor1. Plug a standard 4-pin S-Video cable to the S-Video out jack on your notebook(yellow connector on the back panel) to the S-Video in jack on your television.Restart your notebook.Note Although your notebook has a 7-pin S-Video out jack, the notebook accepts either a 7-pin or 4-pin cable connection.2. Using your mouse, right-click in an empty area of the desktop.3. Select Properties, select the Settings tab, then select the Advanced button. -or- Select Start > Control Panel > Appearance and Themes > Display. Then, select the Settings tab, select the Advanced button, and select the Displays tab.4. To enable the TV, select the red button next to TV.Note If the S-Video cable is not plugged into your notebook and TV, the red button will not be displayed.5. Select Apply to accept the changes.6. If you are prompted to restart Windows, select Yes.Switching the display to the external monitor• Press the TV Now! One-Touch button at the top of your keyboard to switch thedisplay to the external monitor.• With the default display settings, the external monitor uses the same settings asthe internal display. The external monitor displays the same image as the internaldisplay, regardless of the screen area, colors, and other settings, and the refreshrate is the same as the internal display (60 Hz). If you use only the externalmonitor, you can select different settings that aren’t limited by the internaldisplay.
Add-On DevicesConnecting External DevicesReference Guide 53Adjusting monitor resolution and other settings1. Select Start > Control Panel > Appearance and Themes > Display.2. On the Settings tab, adjust the Screen area. Other settings are also available.If you need to increase the refresh rate on the external monitor, you can switch toonly the external monitor. An alternative is to make one display a “secondary”display so you can select independent refresh rates:1. Select Start > Control Panel > Appearance and Themes > Display.2. On the Settings tab, select the Advanced button, then the Displays or Monitortab. Set the refresh rate on the Monitor tab.Using dual display modeYou can extend your desktop by connecting an external monitor to your notebook.1. Select Start > Control Panel > Appearance and Themes > Display.2. Select the Settings tab.3. Select the second display, then select the option to extend the desktop.You can set different resolutions and numbers of colors for each display. However,using the Extended Desktop requires video memory for each display. For this reason,higher resolutions and higher numbers of colors may cause unexpected behavior onthe displays. Try starting with 1024 ×768 resolution on the external display and64 K colors (16-bit) on both displays. You can then try higher settings to see whetherthey work for your applications. In addition, certain operations such as playingDVDs and running 3D graphics require extra video memory, so you may have toadjust display settings.If you’re playing a DVD movie, the movie will show only on the primary display. Tochange the primary display, go to the Settings tab of Display Properties (see the stepsabove), right-click the display you want, and select Primary.To connect an IEEE 1394 device (select models only)If your notebook has an IEEE 1394 port, you can use it to connect devices such asaudio and video equipment, disk drives, printers, and other notebooks.Attach the device cable to the IEEE 1394 port. Windows automatically recognizesthe device.
Add-On DevicesConnecting External Devices54 Reference GuideThe IEEE 1394 port is a 4-wire port. If you want to connect a device that has a6-wire plug, you can purchase a simple adapter if the device is unpowered, or a hubif the device requires power.Note If you have problems making this connection, contact the device manufacturer Website for the latest version of the driver for the device.To connect an infrared device (select models only)Note Select models include an infrared port. By default, the infrared port is not enabled, so you must first enable it before you can use it.If your model has an infrared port (a small, rectangular lens located on the front ofthe notebook), then your notebook has wireless, serial communication capability.That is, your notebook and other infrared devices, such as printers or othernotebooks, can communicate wirelessly using this port.Using the infrared port• Make sure the infrared port of your notebook and the infrared port of the devicewith which you want to communicate lie in a straight line facing each other. Thetwo ports should be no more than one meter apart with no obstructions inbetween. Noise from nearby equipment can cause transmission errors.1. Select Start > Control Panel > Performance and Maintenance > System.2. Select the Hardware tab.3. Select the Device Manager button.4. Select the ALI fast infrared controller, then the Enable Device button.5. Select Next > Finish > Close. Then close all open dialog boxes.• To check the status of communications, open Wireless Link by selecting Start >Control Panel > Printers & Other Hardware > Wireless Link.Printing to an infrared printerInstall your printer and assign it to the notebook infrared port. You can then printfrom your applications as you would to any other printer.Transferring files through an infrared connectionYou can use your notebook infrared port to transfer files by using Wireless Link. Seethe Windows online Help for instructions on using Wireless Link.
Add-On DevicesConnecting External DevicesReference Guide 55To use a port replicator (select models only)A port replicator provides your notebook with external connections that you canleave in place whenever you remove the notebook from your desk. Instead ofdisconnecting and reconnecting peripheral devices, you can simply undock and dockthe notebook.CAUTION Use only the AC adapter included with your notebook (or other approvedadapter that meets the power requirements of the notebook).Do not use a 60-watt, 3.16-amp adapter, and do not use DC adapter accessoriesF1455A and F2297A.Using the wrong AC adapter could damage the notebook or adapter and causedata loss, and may void your warranty.You can dock or undock the notebook in any power state: on, off, Standby, orHibernation. Make sure, however, that the notebook is not entering into or resumingfrom Standby or Hibernation when you dock or undock, or the notebook couldlock up.Hint Before docking or undocking your notebook, save your data and close anyapplications associated with external connections that might be affected. Do this as aprecaution against an unlikely docking problem.
Add-On DevicesConnecting External Devices56 Reference GuideTo dock to the port replicator1. Plug in the AC adapter, then connect it to the back of the port replicator. You canalso operate the port replicator using power from the notebook battery.2. Remove the rubber cover from the docking connector on the bottom of thenotebook.3. Align the notebook with the locator posts on the port replicator.4. Press the notebook down until both sides snap into place.5. If the notebook is off, open it and press the power button to turn it on. The lightson the port replicator turn on.When the notebook is docked, you can use its security connector to secure it. Tosecure both the notebook and port replicator, install the cable lock in the securityconnector next to the undock button. This will also lock the undock button.Note If a device is connected to an audio port on the notebook, any device connected tothe corresponding port on the port replicator is ignored.
Add-On DevicesConnecting External DevicesReference Guide 57To undock from the port replicator1. Press down the undock button on the right side of the port replicator.2. Lift the notebook out of the port replicator.
Add-On DevicesInstalling Additional RAM (Memory)58 Reference GuideInstalling Additional RAM (Memory)The notebook has two slots that hold two RAM modules. At least one slot contains aRAM module installed at the factory. You can use both slots to expand your RAM.To install a RAM expansion moduleUse PC2100 DDR-266 MHz or higher RAM only.You’ll need a small Phillips screwdriver for these steps.CAUTION The internal components of your notebook are extremely sensitive to staticelectricity and can be permanently damaged by it. Handle the RAM moduleonly by its edges. Before installing the memory module, discharge your body’sstatic electricity by touching the metal shielding around the connectors on theback of the notebook.1. Select Start > Turn Off Computer > Turn Off.2. Important: unplug the AC adapter, if present, and remove the battery.3. Turn the unit bottom-side up, loosen the screws holding the RAM cover, andremove the cover.
Add-On DevicesInstalling Additional RAM (Memory)Reference Guide 594. Insert the RAM board into the connector at about a 30 degree angle until it isfully inserted. Then press down at both sides until both latches snap closed.Match your notebook to one of the following illustrations.5. Replace the cover.6. Insert the battery.To remove the RAM module, release the two latches at the sides of the module.
Add-On DevicesInstalling Additional RAM (Memory)60 Reference GuideTo remove a RAM expansion moduleYou may want to remove a RAM module so you can install a larger one. You willneed a small Phillips screwdriver for these steps.CAUTION The internal components of your notebook are extremely sensitive to staticelectricity and can be permanently damaged by it. Handle the RAM moduleonly by its edges. Before installing the memory module, discharge your body’sstatic electricity by touching the metal shielding around the connectors on theback of the notebook.1. Select Start > Turn Off Computer > Turn Off.2. Important: unplug the AC adapter, if present, and remove the battery.3. Turn the unit bottom-side up, loosen the screws holding the RAM cover, andremove the cover.
Add-On DevicesInstalling Additional RAM (Memory)Reference Guide 614. Release the two latches at the sides of the RAM board, so the free edge of theboard pops up. Match your notebook to one of the following illustrations.5. Pull the board out of the connector.6. Replace the cover.7. Insert the battery.
Add-On DevicesReplacing the Hard Drive62 Reference GuideReplacing the Hard DriveTo replace the hard driveYou will need a small Phillips screwdriver for this procedure.1. Unplug the AC adapter, if connected.2. Remove the battery.3. Turn the unit bottom side up.4. Use a pointed tool to remove the plugs from the two screw holes, then removethe two screws.5. Gently pull the hard drive out of the notebook.6. Gently slide the new drive into the hard drive compartment. Press firmly to makesure the connector seats properly.7. Reinstall the hard drive screws and plugs.Important If you are installing a new hard drive, you should create a Utility partition on thedrive before loading any software.
Add-On DevicesReplacing the Hard DriveReference Guide 63To replace the hard drive holderIf you are installing a new hard drive that does not have a holder, you can remove theholder parts from the old hard drive. You will need a small Phillips screwdriver forthis procedure.1. Remove the four screws from the sides of the holder and drive case, then slidethe drive out of the holder.2. Notice that the hard drive has a pin connector attachment at one end. Carefullyremove this connector from the end of the drive. Work alternately at each end sothat the connector slides off evenly without bending the connector pins.3. Carefully put the pin connector attachment back onto the pins on the end of thenew hard drive. Work alternately at each end so that the connector slides onevenly without bending the connector pins.4. Insert the drive into the holder.5. Reinstall the screws into the holder and drive case.
Add-On DevicesReplacing the Hard Drive64 Reference GuideTo prepare a new hard driveWhen you install a new hard drive, you also need to prepare it to be able to workwith your notebook.If you want to restore the Windows software and operating system that wereoriginally installed on your notebook, use the QuickRestore System Recovery CDincluded with your notebook.
Reference Guide 65Troubleshooting and Maintenance
Troubleshooting and MaintenanceTroubleshooting Your Notebook66 Reference GuideTroubleshooting Your NotebookThis chapter contains solutions to many types of problems you might have with yournotebook. Try the solutions one at a time, in the order in which they are presented.Here are some other sources of information for troubleshooting:• Use the Windows troubleshooters. Select Start > Help and Support.• See the Microsoft Windows manual shipped with the notebook.• Select the question mark on the One-Touch key located at the top of thekeyboard.• Refer to the Worldwide Telephone Numbers booklet to contact a Customer CareCenter for help and support.Audio problemsIf no sound is audible• If your model has a volume control, press the + (plus) button to increase volume.• Select the speaker icon on the taskbar (if present), then clear the Mute Allcheckbox if selected. If your model has an audio mute button, press it so theindicator light goes off.• When you are operating your notebook in MS-DOS mode (for example, whenrunning MS-DOS games), you may find that the sound does not operate properly.Use Windows applications for full use of sound capabilities.If sound does not record• Plug in an external microphone. The notebook does not have a built-inmicrophone.• Check the software controls for recording sound. Select Start > All Programs >Accessories > Multimedia (or Entertainment) > Sound Recorder.• In Volume Control, select Options > Properties, then make sure the microphoneis enabled in the recording controls.
Troubleshooting and MaintenanceTroubleshooting Your NotebookReference Guide 67If you hear loud, high-pitched feedback from the speakers• In the Volume Control, try reducing the Master volume by selecting the speakericon in the taskbar.• In Volume Control, select Options > Properties, then select the microphoneoption for the playback settings. Also in Volume Control, make sure themicrophone is muted.CD-ROM and DVD problemsIf you can’t boot from a CD or DVD• Make sure the CD or DVD is bootable, such as the QuickRestore SystemRecovery CD included with your notebook.• Make sure the CD-ROM/DVD drive is selected as the boot device. See the“Basic Operation”chapter for directions.• Restart the notebook: select Start > Turn Off Computer > Restart.If a DVD plays erratically• Dirt or smudges can cause a disc to skip. Clean the disc with a soft cloth. If thedisc is badly scratched, it will probably have to be replaced.• If you are playing the DVD on battery power, try changing the power scheme.If you get a Region Code error when playing a DVD movie• DVDs can have regional codes embedded in the disc data. These codesprevent DVD movies from being played outside the region of the world in whichthey are sold. If you get a Region Code error, you are trying to play a DVDintended for a different region.If the notebook cannot read a CD or DVD• For a single-sided CD or DVD, make sure the disc is placed in the drive with thelabel facing up.• Clean the disc.• Wait 5 to 10 seconds after closing the tray to give the notebook time to recognizethe disc.
Troubleshooting and MaintenanceTroubleshooting Your Notebook68 Reference Guide• Restart the system. Remove the disc from the drive, then select Start > Turn OffComputer > Restart.• If you created the CD on a CD/DVD RW combo drive, try using a differentmedia brand. Read and write quality may vary by media.If a DVD movie doesn’t fill the screenEach side of a double-sided DVD has a different format (standard or widescreen). Inwidescreen format, black bands appear at the top and bottom of the screen. To viewthe standard format, flip the disc over and play the other side.If a DVD doesn’t play with two displaysIf you are using the Extended Desktop (dual displays), move the player window tothe display selected as primary. If you’re not using Extended Desktop and bothdisplays are active, press the TV Now! One-Touch button at the top of the keyboardto switch to one display.If the notebook can’t find Wordpad.exe after inserting a CDThe system is trying to open a .doc file in WordPad, but cannot find theWordpad.exe program file. Type C:\Program Files\Accessories in theerror message box.Display problemsIf the notebook is on, but the screen is blank• Move the mouse or tap the TouchPad. This will wake the display if it is off.• If the notebook is cold, allow it to warm up.If the screen is difficult to read• Try setting the display resolution to its default setting of 1024 ×768 or higher,depending on your model: select Start > Control Panel > Appearance andThemes > Display.• Try adjusting the size of the desktop icons and labels.
Troubleshooting and MaintenanceTroubleshooting Your NotebookReference Guide 69If an external display does not work• Check the connections.• The external monitor may not be detected. In the BIOS Setup utility, try settingVideo Display Device to Both in the System Devices menu.Hard drive problemsIf the notebook hard drive doesn’t spin• Make sure the notebook has power. If necessary, connect the AC adapter, thenmake sure it is fully plugged into a power source and into the back of thenotebook.• Remove and reinsert the hard drive.If the hard drive makes a buzzing or whining noise• Back up the drive immediately.• See whether the noise is coming from elsewhere, such as from the fan or aPC Card drive.If files are corrupted• Open My Computer, select the disk you want to scan, then select File >Properties. Select the Check Now box under the Error-checking section of theTools Tab.• Run the virus-scanning program.• If necessary, you can format the hard disk and reinstall the original factorysoftware using the QuickRestore System Recovery CD included with yournotebook.
Troubleshooting and MaintenanceTroubleshooting Your Notebook70 Reference GuideHeat problemsYour notebook normally gets warm during routine operation.If the notebook gets abnormally hot• Always set the notebook on a flat surface, so that air can flow freely around andunderneath it.• Make sure the air vents on the bottom and sides of the notebook are clear.• Keep in mind that games and other programs that drive CPU usage toward100 percent can increase the notebook temperature.Infrared problemsBy default, the infrared port is not enabled, so you must enable it before you canuse it.If you have problems with infrared communications• Make sure the line between the two infrared ports is not blocked, and that theports face each other as squarely as possible. (The notebook infrared port islocated on the front of the notebook.) The ports should be no more than 1 meterapart.• Check settings in the Device Manager:1. Select Start > Control Panel > Performance and Maintenance > System.2. On the Hardware tab, select Device Manager and expand the infrared devices.Select the infrared port and make sure that the device is enabled.• Make sure only one application is using the infrared port.
Troubleshooting and MaintenanceTroubleshooting Your NotebookReference Guide 71Keyboard and pointing device problemsUse these suggestions for built-in or external devices.If the pointer is difficult to controlAdjust the pointer controls. Select Start > Control Panel > Printers and OtherHardware > Mouse.If the TouchPad doesn’t work• Press the TouchPad on-off button to turn on the light.• Don’t touch the TouchPad while the notebook is rebooting or resuming fromStandby mode. If this happens, try the following: press a key on the keyboard torestore normal operation.• If an external mouse is connected, the built-in pointing devices are normallydisabled. You can change this setting with the BIOS Setup utility. See“Configuring Your Notebook”in this chapter.• Restart the notebook. Select Start > Turn Off Computer > Restart.If the TouchPad moves the pointer or cursor while you typePress the TouchPad on-off button to turn off the TouchPad while you type.If a PS/2 scroll mouse doesn’t work• The TouchPad must be disabled for the mouse scroll feature to work. In the BIOSSetup utility, make sure the External Pointing Devices option in the SystemDevices menu is set to Auto. See “Configuring Your Notebook”in this chapter.• Put the notebook into Standby or shut it down before you attach the scroll mouse,so that it will be detected properly.If you want to use the TouchPad again, you must put the notebook into Standbyor shut it down before you detach the scroll mouse.
Troubleshooting and MaintenanceTroubleshooting Your Notebook72 Reference GuideLocal area network (LAN) problemsIf the built-in network adapter doesn’t connect to the LAN• Check all cables and connections. Try connecting at a different network station,if available.• If the yellow light next to the LAN port does not light, the LAN cable may not beconnected to the network or the network may be down. Try connecting adifferent computer to the cable.• Make sure the LAN cable is Category 3, 4, or 5 for 10Base-T operation, orCategory 5 for 100Base-TX operation. Maximum cable length is 100 meters(330 feet).• Select Start > Help and Support, then use the Networking troubleshooter.• Open the hardware Device Manager. Select Start > Control Panel > Performanceand Maintenance > System. If the network interface is disabled, try to enable it. Ifit has a conflict, try disabling another device.If you can’t browse the Network Neighborhood or My Network PlacesSelect Start > Search > Computers or People to look for a computer.If you can’t log in to Netware serversIf a Netware server is using IPX/SPX protocol, you may need to force your frametype to match the server frame type. Check with your network administrator.If a network connection responds slowlyIf your network connection uses a proxy server, try enabling the option for bypassingthe proxy server for local addresses. You can do this in Control Panel under yournetwork connection properties.
Troubleshooting and MaintenanceTroubleshooting Your NotebookReference Guide 73Memory problemsIf a message says you are out of memory• Make sure drive C is not running low on free space.• If you are having memory problems while running MS-DOS programs, use theMS-DOS or Application and Software troubleshooter in Windows Help: selectStart > Help and Support.• The full amount of RAM in your notebook is not available for runningapplications. A certain amount of RAM is used for display memory. The amountof display memory is shown in the BIOS Setup utility.If memory doesn’t increase after adding RAMMake sure your notebook is using only PC2100 DDR-266 or higher memory (RAM)modules.If the notebook beeps but doesn’t start after adding RAMYou installed an incompatible type of RAM. Remove the module.Modem problemsIf the modem seems slow• Excess static or noise on a line reduces the overall transmission speed of themodem connection. If necessary, contact your telephone company about fixingthis type of problem.• If you’re dialing internationally, line noise is often a problem that’s difficult orimpossible to eliminate.• If you have call-waiting, disable it. Your telephone company can provideinstructions. It can cause symptoms similar to static.• Eliminate extra connections in the line. If possible, connect directly to thewall jack.• Try another telephone line, preferably one normally used for a fax machine ormodem.
Troubleshooting and MaintenanceTroubleshooting Your Notebook74 Reference GuideIf the modem doesn’t dial or no dial tone is detected• Check all cables and connections.• Connect a standard telephone to the phone line and make sure the line is working.• Make sure someone else isn’t using the same phone line.• Try another telephone line, preferably one normally used for a fax machine ormodem.• If you’re in a foreign country, the dial tone may not be recognized by the modem.In Control Panel, open Phone and Modem Options. Try disabling the option thatwaits for a dial tone.If the modem dials incorrectly• Check the telephone number you entered, including any digits required foroutside access or long distance.• In Control Panel, open Phone and Modem Options. Check the dialing options—look for duplicate digits for outside access or long distance.• Make sure the number you’re calling isn’t busy.• If you’re in a foreign country, the dial tone may not be recognized by the modem.In Control Panel, open Phone and Modem Options. Try disabling the option thatwaits for a dial tone.• If you have call-waiting, disable it—your telephone company can provideinstructions.If the modem dials but doesn’t connect• Make sure you’re using an analog telephone line (2, 3, or 4 wires). You must notuse a digital line. In a hotel, ask for a data line.• Try another telephone line, preferably one normally used for a fax machine ormodem.• The modem at the other end may have a problem. Try dialing to a differentmodem.If the modem isn’t detected• Check the modem setup. In Control Panel, open Phone and Modem Options.Check the COM port.
Troubleshooting and MaintenanceTroubleshooting Your NotebookReference Guide 75• Open the hardware Device Manager: select Start > Control Panel > Performanceand Maintenance > System. If the modem is disabled, try to enable it. If it has aconflict, try disabling another device.• If you’re running fax software using fax Class 2, try using Class 1.If the modem dials but you can’t hear it• If your model has an audio mute light, make sure it is turned off. If it’s on, pressthe audio mute button.• Check the speaker volume setting.• In Control Panel, open Phone and Modem Options. Select the modem and selectProperties, then check the volume setting on the General tab.If the modem connects, but transferred data is bad• In Control Panel, open Phone and Modem Options. Make sure the parity, speed,word length, and stop bits match on sending and receiving modems.• Try a different telephone line, or dial a different server number.If the modem causes an ERROR message• A string of AT commands may contain an incorrect command. If you enteredcommands as extra settings for the modem in Control Panel or in yourcommunications software, check the commands.If the modem doesn’t fax• If you’re using fax Class 2 in the fax software, try using Class 1.• Close any other communications programs.• If you’re faxing by printing from an application, make sure you’ve selected thefax printer.• Try turning off power management features temporarily.If excessive line current is detectedMake sure you’re using an analog telephone line (2, 3, or 4 wires). You must not usea digital line. In a hotel, ask for a data line.If the modem clicks repeatedly but does not connect• Make sure you are using an analog telephone line (2, 3, or 4 wires). You must notuse a digital line. In a hotel, ask for a data line.• Check all cables and connections.
Troubleshooting and MaintenanceTroubleshooting Your Notebook76 Reference GuidePC Card problemsIf the notebook doesn’t recognize a PC Card• Remove and reinsert the PC Card.• Restart the notebook: select Start > Turn Off Computer > Restart.• Try the card in another computer to see whether the card functions properly.• Zoomed Video is not supported.• If the card requires an IRQ, make sure one is available. Open the hardwareDevice Manager: select Start > Control Panel > Performance and Maintenance >System.If a network PC Card stops communicating properly• The card may have been reset if the notebook entered Standby or shut off. Exitany applications, then remove and reinsert the card.• Check settings in Control Panel.If a PC Card modem is not workingDisable the internal modem:1. Open the hardware Device Manager: select Start > Control Panel >Performance and Maintenance > System.2. Select Modem to list the current modem devices.3. Select the internal modem, then select the option to disable the modem.Performance problemsFor best performance, your notebook should have at least 128 MB ofmemory (RAM).If the notebook pauses or runs sluggishly• This may be normal Windows behavior. Background processing can affectresponse time.• Certain background operations (such as a virus-scanning program) can affectperformance.
Troubleshooting and MaintenanceTroubleshooting Your NotebookReference Guide 77• Press CTRL+ALT+DEL and use Task Manager to see if an application is notresponding.• Restart the notebook: select Start > Turn Off Computer > Restart.• Some file browsers respond slowly while processing graphics or waiting forbroken network connections to time out.• If the notebook hard drive frequently runs (as indicated by the hard drive light onthe front of the notebook) while the notebook appears to be paused or runningslowly, Windows is likely spending excess time writing to its swap file on thenotebook hard disk. If this occurs frequently, consider installing additionalmemory.• Check the amount of available free disk space. Delete temporary and unneededfiles.If the notebook stops responding• Press CTRL+ALT+DEL and use Task Manager to end the application that is notresponding.• Press and hold the power button for at least 4 seconds to turn off and reset thenotebook. Any unsaved data will be lost. Then press the power button again toturn the notebook back on.• If nothing happens, insert the tip of a paper clip into the reset button on thebottom of the notebook. Then press the power button to turn the notebookback on.• To avoid lockup problems, avoid pressing the TV Now! One-Touch button toswitch display devices while graphic-intensive applications are running. Alsoavoid turning the notebook off or putting it into Standby while such applicationsare running.Power and battery problemsIf the notebook turns off immediately after it turns onBattery power is probably extremely low. Plug in the AC adapter or insert a chargedbattery.If the notebook keeps beepingThe notebook beeps repeatedly or displays a warning when battery power is low.Save your work, shut down Windows immediately, and insert a charged battery orplug in the AC adapter.
Troubleshooting and MaintenanceTroubleshooting Your Notebook78 Reference GuideIf the battery doesn’t charge• Make sure the AC adapter is fully plugged into the power source and thenotebook, and that the light on the Adapter is on.• If you’re using a power strip, remove the AC adapter from the power strip andplug it directly into a wall outlet.• Make sure the battery is fully installed and locked in place.• Make sure you’re using only the AC adapter included with your notebook (orother approved adapter that meets the power requirements of the notebook). Donot use a 60-watt, 3.16-amp adapter.• Move the notebook away from any nearby heat source. Unplug the AC adapterand allow the battery to cool down. If the battery gets too hot, it will not chargeproperly.• If available, try another battery and AC adapter.If the notebook has a short operating time• Conserve power using any of the suggestions listed in the “Batteries and PowerManagement”chapter in this guide.• If you are running an application that has an automatic save feature (such asMS Word), disable this feature or increase the specified save time to reduce harddrive access.• If the operating time has gradually become shorter and the battery is more than ayear or two old, you may need to replace the battery.• Heavy modem use can affect battery operating time.• PC Card use can affect battery operating time.• Test and recondition the battery every 3 months.If the Time Remaining for the battery is not correctThe Time Remaining is an estimate, not a precise value, and is based on the rate atwhich the notebook is using power at the moment. This value therefore depends onyour current task, and assumes that you will continue using power at the same rateuntil the battery runs out. So, if you check the Time Remaining while the notebook isperforming a task requiring a good deal of power (such as reading from a CD orDVD), the value will probably show less time remaining than you really have, sinceyou will probably later switch to tasks that require less power.
Troubleshooting and MaintenanceTroubleshooting Your NotebookReference Guide 79If the notebook doesn’t enter Standby as expected• If you have a connection to another computer, the notebook won’t enter Standbyif the connection is active.• If the notebook is performing an operation, it normally waits for the operation tofinish before entering Standby.If the notebook doesn’t automatically enter Hibernation as expected• Make sure Hibernation support is enabled. From Control Panel, open PowerOptions, then select the Hibernate tab.• Check the Power Schemes tab. Make sure the Hibernate timeouts for both ACpower and battery power are not set to Never.Printing problemsHint You will usually be able to solve most printing problems by using the Printtroubleshooter in Windows Help: select Start > Help and Support.If a serial or parallel printer doesn’t print• Make sure the printer is on and has paper in it.• Make sure you are using the correct printer cable or cable adapter, and that thecable is secure at both ends.• Check for printer errors.If the left edge of printed output is missingCertain applications may not work properly with 600-dpi printers. If you’re usingsuch a printer, try selecting a compatible printer driver for a 300-dpi printer.If an infrared printer doesn’t print• Make sure the line between the two infrared ports is not blocked, and that theports face each other as squarely as possible. (The notebook infrared port islocated on the front of the notebook.) The ports should be no more than 1 meterapart.• Make sure the printer is on and has paper in it.• Check for printer errors.• Make sure Windows is running; otherwise infrared printing is not available.
Troubleshooting and MaintenanceTroubleshooting Your Notebook80 Reference GuideSerial, parallel, and USB problemsIf a serial mouse doesn’t work• Make sure you followed the manufacturer’s installation instructions completelyand have installed the mouse properly. If not, repeat the procedure.• Make sure the port connection is secure.• Press the power button to enter Standby, and again to resume.• Restart the notebook: select Start > Turn Off Computer > Restart.• Check mouse settings in Control Panel: select Start > Control Panel > Printersand Other Hardware > Mouse.• Use a mouse that connects to the USB or PS/2 port. If you have a PS/2 keyboardconnected, use a PS/2 Y adapter (HP accessory F1469A).• Check the port settings in Control Panel. Open the hardware Device Manager,then select Ports (COM & LPT).If a serial modem doesn’t work properly• Make sure the port connection is secure.• Use the Modem troubleshooter in Windows Help: select Start > Help andSupport.• In Control Panel, open Phone and Modem Options, and check the modemsettings.• Disable the internal modem:1. Open the hardware Device Manager: select Start > Control Panel >Performance and Maintenance > System.2. Select Modem to list the current modem devices.3. Select the internal modem, then select the option to disable the modem.• Check the port settings in Control Panel. Open the hardware Device Manager,then select Ports (COM & LPT).If the serial or parallel port is not working• Make sure the port connection is secure.• Check the port settings in Control Panel. Open the hardware Device Manager,then select Ports (COM & LPT).
Troubleshooting and MaintenanceTroubleshooting Your NotebookReference Guide 81If the USB port is not working• Contact the vendor of the peripheral device for the latest USB drivers.• Check the port settings in Control Panel. Open the hardware Device Manager,then select Universal Serial Bus Controller.Startup problemsIf the notebook does not respond when you turn it on• Connect the AC adapter.• Reset the notebook by inserting the tip of a paper clip into the reset button on thebottom of the notebook. Then press the power button to turn it on.• If the notebook still doesn’t respond, remove the battery and AC adapter, removeany PC Cards, and undock the notebook if docked. Then plug in the AC adapteragain, and reset the notebook using the reset button.If the notebook won’t boot from battery power• Make sure the battery is properly inserted and fully charged. Check the batterycharge by removing it and pressing the pad on the side of the battery. The lightsshow the charge level.• If available, try another battery.If the notebook will not boot from the diskette drive• Make sure the diskette drive is selected as the boot device. See the “BasicOperation”chapter in this guide for directions.• If you’re using a USB diskette drive, use the BIOS Setup utility to make sureLegacy USB Support is enabled. If your notebook also has a built-in diskettedrive, use the BIOS Setup utility Boot menu to make sure the USB diskette driveis the first device under Removable Drive.If the notebook stops responding after bootingCheck whether you are connected to a TCP/IP network with no DHCP server. Thiscan cause a long delay at startup because DHCP is enabled. Contact your networkadministrator to determine the proper TCP/IP configuration.
Troubleshooting and MaintenanceTroubleshooting Your Notebook82 Reference GuideIf the notebook takes a long time to resume after entering StandbyThe notebook can routinely take a minute or more to resume if it has a network cardinstalled. While the operating system is loading drivers and checking hardware andnetwork connections, you will see a blinking cursor on your display. As soon as thehardware has been re-initialized, the Windows desktop will appear.Wireless problemsIf you have problems with wireless 802.11 communication• Make sure the wireless indicator light is on.• If your notebook includes Bluetooth capabilities, make sure wireless 802.11communication is turned on. Select Start > All Programs > Utilities > WirelessConfiguration, then select the 802.11 button if it’s not turned on.• Make sure you are using the correct SSID and channel settings.• Make sure you are in range of an access point (for an infrastructure connection)or other wireless computer (for an Ad Hoc connection).• When you log on to an 802.11 network via an access point, yet your notebookcannot connect to network resources, your notebook may not have been assignedan IP address. If the subnet mask for your wireless connection is255.255.000.000, the network server did not assign an IP address to yournotebook, and you may have to release and renew your network IP address. Ifthis does not fix the problem, the access point may need to be rebooted.• If you want to change the SSID to a different value to connect to a differentaccess point, or if you want to change from Infrastructure mode to Ad Hoc mode,you may first have to release and renew the Internet IP address.• See “Local area network (LAN) problems”in this chapter.If you have trouble connecting to another computer in the NetworkNeighborhood or My Network Places• Wait a few minutes, then press F5 to refresh the list of computers on the network.• Select Start > Search > Computers or People to locate the computer.If you cannot connect to a particular computer on the network• Make sure the computer is properly connected to the network.• Make sure your TCP/IP setup is correct for your network: in Control Panel, openNetwork Connections.
Troubleshooting and MaintenanceTroubleshooting Your NotebookReference Guide 83If you can connect, but the network is slow• Check whether you might be in an area served by more than one wireless LAN.If so, the LANs could be interfering with each other.• Move closer to the access point (for an infrastructure connection) or otherwireless computer (for an Ad Hoc connection). You could be too far away forhigh-speed communication.If your notebook cannot detect any Bluetooth devices• Make sure the wireless indicator light is on.• Make sure Bluetooth communication is turned on. Select Start > All Programs >Utilities > Wireless Configuration, then select the Bluetooth button if it’s notturned on. If no Bluetooth button is shown, your notebook does not supportBluetooth communication.• Make sure the Bluetooth devices are turned on. Some Bluetooth phones must beset for detection and may be detectable by other devices for only a short time.If your notebook cannot detect a certain Bluetooth device• Make sure the Bluetooth device is turned on. Some Bluetooth phones must be setfor detection and may be detectable by other devices for only a short time.• Refresh the list of Bluetooth devices. Select the Bluetooth icon in the taskbar,then select Bluetooth > Search For Devices in the menu bar.
Troubleshooting and MaintenanceConfiguring Your Notebook84 Reference GuideConfiguring Your NotebookThe BIOS Setup utility helps you configure your notebook operation.To run the BIOS Setup utilityThe BIOS (basic input and output system) Setup utility enables you to make changesto the notebook system configuration, and to tailor the operation of your notebook toyour individual work needs.The settings made in BIOS Setup generally control the notebook hardware, and sogreatly affect how the notebook operates.1. Select Start > Turn Off Computer > Restart.2. When the logo screen appears, press F2 to enter BIOS Setup.3. The pointing devices are not active in BIOS Setup, so you will need to use thekeyboard to navigate:• Press the LEFT and RIGHT arrow keys to move among menus.• Press the UP and DOWN arrow keys to move among parameters in a menu.• Press + or –to move through values for the current parameter, or pressENTER to change a setting.4. After you select the options you want, press F10 or use the Exit menu to exitBIOS Setup.5. If the settings cause a conflict between devices during reboot, the system promptsyou to run BIOS Setup, and marks the conflicting settings.The following tables describe BIOS settings for the BIOS version at publication. Ifyour BIOS is a different version, some settings may differ from those shown.
Troubleshooting and MaintenanceConfiguring Your NotebookReference Guide 85Main MenuSetting Description DefaultBIOS Revision Shows the current BIOS version. DetectedautomaticallySystem Time Sets the time using 24-hour format. Values set takeeffect immediately.System Date Sets the date using dd/mm/yy format (except English,which uses mm/dd/yy format).Language Sets the language for BIOS Setup. DetectedautomaticallyInternal Hard Disk Sets the hard drive type and various parameters. DetectedautomaticallyUMA Video Memory Sets the video memory size allocated from totalinstalled memory (RAM).AutoMemory Shows the extended memory size. DetectedautomaticallySerial Number Displays the serial number as shown on the back ofthe unit.DetectedautomaticallyService ID Displays an identifier used for repair service. DetectedautomaticallyUUID Displays the value of the 16-byte UUID (UniversallyUnique ID) as 32 hex characters.DetectedautomaticallyMAC Address Displays the MAC network address of the internal(wired) LAN.Detectedautomatically
Troubleshooting and MaintenanceConfiguring Your Notebook86 Reference GuideSystem Devices MenuSettingDescription DefaultVideo Display Device Sets whether the built-in display automaticallyswitches to an external display, if one is detected.AutoExternal Pointing Device Disables the internal pointing devices when anexternal pointing device is connected.AutoLegacy USB Support Enables BIOS support for USB mouse, keyboard, anddiskette disk drive during startup.EnabledWake On LAN fromPower OffLets the notebook be turned on via the LAN port. Ifthis option is enabled, the notebook uses increasedpower while it is shut down.DisabledSecurity MenuSetting Description DefaultUser Password is Shows if a user password is set. ClearAdministrator PasswordisShows if an administrator password is set. ClearSet User Password Press ENTER to set, change, or clear the userpassword. The password can have no more than 8characters (0-9, A-Z), and cannot include special oraccented characters.EnterSet AdministratorPasswordPress ENTER to set, change, or clear theadministrator password, which protects BIOS Setupsettings. The password can have no more than 8characters (0-9, A-Z), and cannot include special oraccented characters.EnterRequire Password onBootSets whether a user password is required when thenotebook boots. Requires the administrator passwordfor changes.DisabledInternal hard drive lock Only if the Boot password option is enabled, encodesthe current user password (or administrator passwordif that is the only password set) on the hard drive.Disabled
Troubleshooting and MaintenanceConfiguring Your NotebookReference Guide 87Boot MenuSetting Description DefaultHard Drive+Removable DevicesCD-ROM DriveBuilt-in LANShows the order of boot devices. Move the entries tochange the order. If the notebook has more than onedevice in a + category, you can select the onescanned. Built-in LAN provides diskless boot from anetwork server.1. Hard Drive2. RemovableDevices3. CD-ROM Drive4. Built-in LANExit MenuSetting Description DefaultSave Changes and Exit Saves Setup changes, then exits and reboots.Discard Changesand ExitDiscards any Setup changes made since last save,then exits and reboots. Does not affect password, date,or time changes.Get Default Values Restores default settings, and remains in Setup. Doesnot affect password, date, or time changes.To change video memory settings using BIOS Setup utilityThe notebook comes with either 32MB or 16MB of video memory.Note Changing your video memory to 8MB, 16MB, 32MB, or 64MB may change theperformance of your notebook, depending on your selection.To change your video memory:1. Select Start > Turn Off Computer > Restart.2. Press F2 when the splash screen appears.3. Move the down arrow key until UMA Video Memory is highlighted. PressEnter to bring up a list of memory settings. Selections include 8 MB, 16MB,64MB, or Auto.4. Press F10 to save configuration changes and exit BIOS screen.
Troubleshooting and MaintenanceReinstalling and Updating Software88 Reference GuideReinstalling and Updating SoftwareYour notebook includes two features that allow you to install individual softwareapplications or to restore the entire original contents of your hard drive:• QuickRestore System Recovery CD, included with your notebook, allows you torestore your hard drive to its original factory contents.• Application Recovery utility allows you to restore or install one or moreapplications. Select Start > Software Setup, then follow the installation wizard onthe screen.To replace a damaged QuickRestore System Recovery CDIf you lose or damage the QuickRestore System Recovery CD, refer to the servicetelephone numbers in the Worldwide Telephone Numbers booklet to contact aCustomer Care Center for help and support.
Reference Guide 89Reference Information
Reference InformationModem Reference Information90 Reference GuideModem Reference InformationYou can customize the operation of the modem using AT commands and S-registers.You can do this from Phone and Modem Options in Control Panel, from mostcommunications software, or by using terminal mode in your software.Note You should have a good understanding of modems and how they operate before youchange default settings.This section contains summary information about AT commands, S-registers, andselected result codes for the built-in modem.Modem Reference (Conexant)All listed AT commands must be preceded by the characters “AT”(except for thecommand “A/”). The commands can be entered in upper or lower case. Manycommands can be used as queries by entering “?”as the argument.Conexant AT Commands (Advanced Users Only)Command Function (Conexant)A Go off-hook and attempt to answer a call.A/ Re-execute command (not preceded by AT).DnDial modifier: 0–9, A–D =DTMF digits; L=redial last number; P=pulse dialing; T=tone dialing;W=wait for dial tone; * (“star”); # (“pound sign”); +; !=flash; @=wait for silence; $ or &=wait forcredit card dialing tone; ,=return to command state; ‘=dial pause; ^=toggle calling tone.Parentheses, hyphens, and spaces can be used to format dial string and have no other effect.E0 Turn off command echo.E1 Turn on command echo (default).H0 Initiate hang-up sequence.H1 If on-hook, go off-hook and enter command mode.I0 Report product code.I1 Report LSB of stored checksum.I2 Report “OK”.I3 Report identification codes.I4 Report product description.I5 Report country code parameter.I6 Report modem data pump model and internal code revision.I7 Report modem data pump model and internal code revision.I8 Report “OK”.I9 Report country.LnSet speaker volume: 0=off, 1=low (default), 2=medium, 3=high.MnActivate speaker: 0=off, 1=on during handshaking and off when receiving carrier (default),2=always on, 3=off when dialing and receiving carrier, on when answering.
Reference InformationModem Reference InformationReference Guide 91Conexant AT Commands (Advanced Users Only)Command Function (Conexant)N0 or N1 Included for compatibility only; returns result code.On0=go on-line, 1=go on-line and initiate retrain sequence.P Force pulse dialing.Qn0=enable result codes to DTE (default), 1=disable.SnSelect S-register nas default.Sn=vSet default S-register nto value v.T Force DTMF dialing.VnReport result codes: 0=short form (terse), 1=long form (verbose) (default).W0 Report DTE speed (default).W1 Report line speed, error correction protocol, and DTE speed.W2 Report DCE speed.W3 Report DCE speed and error correction protocol.X0 Report CONNECT result code on connecting. Dial tone and busy detection not reported.X1 Report CONNECT <text> result code on connecting. Dial tone and busy detection not reported.X2 Report CONNECT <text> result code on connecting. Dial tone and busy detection not reported.X3 Report CONNECT <text> result code on connecting. Dial tone not reported, busy signalreported if detected.X4 Report CONNECT <text> result code on connecting. Dial tone and busy signal reported ifdetected (default).Z Reset to default configuration.+DR: aSelect error control protocol: NONE=no data compression, V42B=42bis in both directions,ALT=MNP 5 compression.+DR=n0=disables extended format "+DR:" intermediate result code, 1=enables.+DS=a,b,c,dControls V.42bis data compression function (b,c, and dare optional):asets direction(s) of data compression function, seen by DTE: 0=negotiated, no compression;3=both directions (default).b=0 specifies modem does not disconnect if V.42bis is not negotiated by remote modem asspecified by a.csets maximum number of dictionary entries (2048) that should be negotiated.dsets maximum string length (32 bytes) to be negotiated.+DS44=a,b,c,d,e,f,g,h,iControls V.44 data compression function (b,c,d,e,f,g,h, and iare optional):asets direction(s) of data compression function, seen by DTE: 0=negotiated, no compression;1=transmit only; 2=receive only; 3=both directions (default).bspecifies whether modem disconnects if V.44 not negotiated remote DCE as specified in a:0=do not disconnect (default), 1=disconnect.c: 0=stream method (default), 1=packet method, 2=multi=packet method.d(256 to 2048) sets maximum codewords to be negotiated in transmit direction (default=2048).e(256 to 2048) sets maximum codewords to be negotiated in receive direction (default=2048).f(32 to 255) sets maximum string length to be negotiated in transmit direction (default=32).g(32 to 255) sets maximum string length to be negotiated in receive direction (default=32).h(2048 to 4096) sets maximum size of history buffer to be negotiated in transmit direction(default=4096).i(2048 to 4096) sets maximum size of history buffer to be negotiated in receive direction(default=4096).
Reference InformationModem Reference Information92 Reference GuideConexant AT Commands (Advanced Users Only)Command Function (Conexant)+ESA=a,b,c,d,e,f,g,hControls operation of synchronous access mode:a=0 specifies in transparent sub-mode, modem transmits 8-bit SYN sequence on idle.b=0 specified in framed sub-mode, modem transmits HDLC flags on idle (default and fixed).c=0 specifies in framed sub-mode, modem transmits abort on underrun in middle of frame(default); c=1 specifies in framed sub-mode, modem transmits flag on underrun in middle offrame, notifies DTE.d: not to be commanded.e=0 specifies CRC generation and checking disabled (default and fixed).f=0 specifies NZRI encoding and decoding disabled (default and fixed).g=255 sets the octet value used in character-oriented framing.h: not to be commanded.+GCAP Transmit text listing commands that provide additional modem capabilities.+GCI=nSet country of installation using 8-bit country code from Annex A of T.35.+GMI Report modem manufacturer.+GMM Report modem model.+GMR Report modem version, revision, or date.+GOI Transmit text identifying the device.+GSN Report modem model serial number.+IFC=n,mSet operation of local flow control between DTE and modem.n=method DTE uses to control data flow from modem: 0=none, 1=XON/XOFF on transmitteddata, 2=Circuit 133 (Ready for Receiving) (default).m=method modem uses to control data flow from DTE: 0=none, 1=XON/XOFF on receiveddata, 2=CTS/RTS (default).+ILRR=nReport local port rate: 0=disable, 1=enable.+IPR=nSet data rate at which the modem accepts commands when connected: 0 (allows operationonly at rates automatically detectable by modem), 2400, 4800, 9600, 19200, 38400, 57600, or115200.+ITF=a,b,cSets transmit flow control thresholds (band care optional):a(20 to 7000) sets threshold (octets) above which modem generates flow-off signal insynchronous access mode (default=128).b(10 to 5000) sets threshold (octets) below which modem generates flow-on signal insynchronous access mode (default=64).c=0 (fixed).+PCW=nSet modem behavior with call waiting: 1=request modem-on-hold and collect caller IDinformation, 2=hang up, 3=ignore call waiting.+PIG=n0=enable PCM upstream negotiation, 1=disable (default).+PMH=nSet modem-on-hold: 0=enabled in V.92 mode (default), 1=disabled.+PMHF Initiate flash hook sequence when in modem-on-hold procedure.+PMHR=nRequest modem to initiate or confirm modem-on-hold (MOH) procedure and timeout: 0=V.92modem-on-hold request denied or unavailable, 1 to 13 grant MOH with timeout (1=10 sec,2=20 sec, 3=30 sec, 4=40 sec, 5=1 min, 6=2 min, 7=3 min, 8=4 min, 9=6 min, 10=8 min, 11=12min, 12=16 min, 13=indefinite).+PMHT=nSet whether modem grants modem-on-hold (MOH) request, and MOH timeout: 0=deny V.92modem-on-hold request (default), 1 to 13=grant MOH with timeout (1=10 sec, 2=20 sec, 3=30sec, 4=40 sec, 5=1 min, 6=2 min, 7=3 min, 8=4 min, 9=6 min, 10=8 min, 11=12 min, 12=16min, 13=indefinite).+PQC=nUse Short Phase startup procedures: 0=enable V.92 Short Phase 1 and 2 (default), 1=enableShort Phase 1 only, 3=disable.+PSS=n0=modems decide whether to use short startup procedures, 2=use full startup procedures onall subsequent connections.+VCID=nSet caller ID reporting: 0=disable (default), 1=enable with formatted presentation, 2=enablewith unformatted presentation.
Reference InformationModem Reference InformationReference Guide 93Conexant AT Commands (Advanced Users Only)Command Function (Conexant)+VRID=nReport caller ID: 0=use formatted presentation, 1=use unformatted presentation.-QCPC Use full startup procedures on next connection, then select startup procedure defined by+PQC.-QCPS=n0=do not allow modem to save generated quick-connect profile, 1=allow (default).&CnSet RLSD: 0=always on, 1=follow carrier state (default).&Dn0=ignore DTR; 1=upon on-to-off transition, enter online command state and issue OK resultcode; call remains connected; 2=upon on-to-off transition clear call, discard untransmitted dataaccordingto+ETBM.&En0=disable line quality monitor, auto-retrain, and auto-rate renegotiation;1=enable line qualitymonitor, auto-retrain, and auto-rate renegotiation (default).&F0 Restore factory configuration.&GnIncluded for compatibility only; no effect (returns OK).&KnSet DTE/DCE flow control: 0=disable, 3=enable RTS/CTS DTE/DCE flow control (default),4=enable XON/XOFF DTE/DCE flow control, 5 and 6 included for compatibility only (no effect,returns OK).&MnIncluded for compatibility only; no effect (returns result code).&PnSet pulse dial (pps) with make/break: 0=10 pps with 39%–61% make/break (default), 1=10 ppswith 33%–67% make/break, 2=20 pps with 39%–61% make/break, 3=20 pps with 33%–67%make/break.&Q5 Select asynchronous operation in error correction mode.&Qn(n=0–3, 6) Select asynchronous operation in normal mode (speed buffering).&T0 Terminate any test in progress.&T1 Initiate local analog loopback.&V Display current configuration and stored profiles.%TTnPTT testing of signal level: 00–09=DTMF dial 0–9, 0A=DTMF *, 0B=DTMF #, 0C=DTMF A,0D=DTMF B, 0E=DTMF C, 0F=DTMF D, 10=V.21 Channel 1mark symbol, 11=V.21 Channel2mark symbol, 12=V.23 Channel 1mark symbol, 13=V.23 Channel 2mark symbol, 14=Bell103Channel 1mark symbol, 15=Bell103 Channel 2mark symbol, 20=V22Org, 21=V22Ans,22=Bell212Org, 23=Bell212Ans, 24=V22BisOrg, 25=V22BisAns, 26=V32@4800,27=V32@7200, 28=V32@9600, 29=V.32Bis@12000, 2A=V32Bis@14400, 30=Silence,31=2100Hz MISC, 33=1300Hz MISC, 34=1100Hz MISC, 40=Reserved, 41=V27@2400 FAX,42=V27@4800 FAX, 43=V29@7200 FAX, 44=V29@9600 FAX, 45=V17@7200LT FAX,46=V17@7200ST FAX, 47=V17@9600LT FAX, 48=V17@9600ST FAX, 49=V17@12000LTFAX, 4A=V17@12000ST FAX, 4B=V17@14400LT FAX, 4C=V17@14400ST FAX. 5abc:a=bitrate (0=2400, D=33600), b=V.34 symbol rate (0=2400, 5=3429), c=pre-emphasis filter (0 to A).\N0 Select normal speed buffered mode.\N1 Select normal speed buffered mode.\N2 Select reliable (error-correction) mode.\N3 Select auto reliable mode.\N4 Force LAPM mode.\N5 Force MNP mode.+MCR Report carrier.+MMR Report transmit and receive rates.+MR=0 Disable reporting of modulation connection.+MR=1 Enable reporting of modulation connection (+MCR: and +MRR: are transmitted) (default).+MR=2 Enable reporting of modulation connection (+MCR: and Receive Rate Only: are transmitted).
Reference InformationModem Reference Information94 Reference GuideConexant AT Commands (Advanced Users Only)Command Function (Conexant)+MS=a,b,c,d,e,fSelect modulation (b,c,d,e, and fare optional).ais the carrier (allowable rates in parentheses): B103 (300), B212 (1200 Rx/75 Tx or 75Rx/1200 Tx), V21 (300), V22 (1200), V22B (1200/2400), V23C (1200), V32 (4800/9600), V32B(4800–14400),V34 (2400–33600), K56 (32000–56000), V90 (28000–56000), V92 (downstream: 28000–56000; upstream: 24000–48000).bis automode: 0=disabled, 1=enabled (default).cis minimum transmit (Tx) rate (bps).dis maximum transmit rate (bps).eis minimum receive (Rx) rate.fis maximum receive rate (bps).+WS=nSet PDC mode: 1=disable (default), 20=enable.ECC Commands%CnSet data compression: 0=disable, 1=enable V.42 bis and MNP 5, 2=enable V.42 bis and MNP5,3=enable V.42 bis and MNP 5 (default).+EB=a,b,cSelect break handling (band care optional):a=0 — break is ignored.b=0 — transmitted V.42 L-SIGNAL will not indicate break signal length.c=0 — break is not delivered to DTE.+EFCS=0 Select 16-bit FCS specified in V.42.+ER: aSelect error control protocol: NONE=error control not in use, LAPM=V.42 LAPM protocol,ALT=MNP.+ER=nError control reporting: 0=disable, 1=enable.+ES=a,b,cSelect error control and synchronous mode (band care optional).ais requested mode when modem is originator: 0=initiate call with direct mode, 1=initiate callwith normal mode, 2=initiate V.42 without detection phase, 3=initiate V.42 with detection phase(default), 4=initiate MNP, 6=initiate V.80 synchronous access mode when connection iscompleted.bspecifies fallback mode when modem is originator: 0=LAPM, MNP, or normal mode errorcontrol optional (default); 1=LAPM, MNP, or direct mode error control optional; 2=LAPM orMNP error control required; 3=LAPM error control required; 4=MNP error control required.cspecifies fallback mode when modem is answerer or specifies V.80 synchronous accessmode: 1=error control disabled, use normal mode; 2=LAPM, MNP, or normal mode errorcontrol optional (default); 3=LAPM, MNP, or direct mode error control optional; 4=LAPM orMNP error control required; 5=LAPM error control required; 6=MNP error control required;8=initiate V.80 synchronous access mode when connection complete.+ESR=0 Disable selective repeat option in V.42.+ETBM=a,b,cHandle data remaining in modem buffers on call termination (band care optional):a=0 — disconnect occurs immediately and buffered transmit data is discarded.b=0 — disconnect occurs immediately and buffered receive data is discarded.c=0 — modem does not attempt to deliver buffered data and discards data.FAX Class 1+FAE=nData/fax auto answer: 0=disable (default), 1=enable.+FAR=n0=disable adaptive reception (default), 1=enable.+FCL=nSet loss-of-carrier delay in units of 100 ms (n=0 to 255).+FCLASS=nSet active service class: 0=data mode (default), 1=Fax Class 1, 1.0=Fax Class 1.0 mode,8=voice mode.+FIT=n,aSet DTE inactivity timeout nseconds after which modem goes on-hook (a=0) or DCE goes onhook (a=1).
Reference InformationModem Reference InformationReference Guide 95Conexant AT Commands (Advanced Users Only)Command Function (Conexant)+FLO=aSet flow control type: 0=XON/XOFF and RTS/CTS flow control turned off; 1=XON/XOFF flowcontrol in either direction; 2=RTS for flow control of modem by DTE, and CTS for flow control ofDTE by modem.+FMI Report modem manufacturer.+FMM Report modem model.+FMR Report modem version, revision, or date.+FPR=nSet DTE/modem interface rate in bits/sec: 0=automatic detection (default).+FRH=nReceive data with HDLC framing.+FRM=nReceive data.+FRS=nReceive silence, n×10ms.+FTH=nTransmit data with HDLC framing.+FTM=nTransmit data.+FTS=nStop transmission and wait, n×10ms.Voice Commands+FCLASS=8 Select voice mode.+VDR=a,bSet report ring cadence and timing of RING event code:a=0 disables ring cadence reporting, a=1 enables.bsets report content: 0=DROF and DRON messages only.+VDT=a,bSet report control tone cadence:a=0 disables ring cadence reporting, a=1 enables.b=0 reports CPOF and CPON messages only.+VDX=aSelect speakerphone half-duplex (a=0) or full duplex (a=1).+VGM=nSet microphone gain of speakerphone function (0 to 255).+VGR=nSet gain for received voice samples (0 to 255).+VGS=nSet speaker gain of speakerphone function (0 to 255).+VGT=nSet volume (120 to 135).+VIP Initialize all voice parameters to defaults.+VIT=nSet initial value for DTE/modem inactivity timer (0 to 255 seconds).+VLS=nSelect sources/destinations for analog data.+VNH=nSet automatic hangups: 0=enable, 1=disable, 2=disable automatic hangups in non-voicemodes.+VPR=nSet DTE/modem interface rate (0=autobaud).+VRA=nSet delay between ringbacks before modem assumes remote station is off hook (0 to 255 x 0.1sec).+VRN=nSet delay between ringbacks before modem assumes remote station is off hook (0 to 60 sec).+VRXnStart voice reception: 0=start without periodic tone production, 1=start with periodic toneproduction.+VSD=a,bSet silence detection sensitivity and required period of silence before modem reports silence atend of voice receive.+VSM=a,b,c,dSet voice and silence compression methods, and voice sampling rate.+VSP=aDisable (a=0) or enable (a=1) speakerphone.+VTD=nSet beep duration (1 to 500 x 0.01 sec).+VTR Start voice transmission and reception.+VTS=string Send voice tones.+VTX Start voice transmission.AT* Commands*B Display black-listed numbers.*D Display delayed numbers.
Reference InformationModem Reference Information96 Reference GuideS-Registers (Conexant)Register Function (Conexant) Range/units DefaultS0 Number of rings to auto-answer. 0–255/rings 0S1 Ring counter. 0–255/rings 0S2 Escape character. 0–255/ASCII 43S3 Line termination character. 0–127/ASCII 13S4 Response formatting character. 0–127/ASCII 10 (line feed)S5 Command line editing character. 0–32/ASCII 8(backspace)S6 Wait time for dial tone. 2–255/sec 2S7 Wait time for carrier. 1–255/sec 50S8 Pause time for dial delay modifier. 0–255/sec 2S10 Carrier loss disconnect time. 1–255/.1 sec 14 (1.4 sec)S11 DTMF tone duration. 50–255/.001 sec 95 (95 msec)S12 Escape prompt delay. 0–255/.02 sec 50 (1 sec)S18 Test timer. 0–255/sec 0S29 Flash dial modifier time. 0–255/10 msec 70 (700msec)S30 Disconnect inactivity timer. 0–255/10 sec 0S46 Data compression control. 136 (error correctionw/o compression) or138 (error correction& compression)138S95 Extended result code messages control. 0Selected Result Codes (Conexant)Code Meaning0OK1 CONNECT2RING3 NO CARRIER4 ERROR5 CONNECT 12006NODIALTONE7BUSY8NOANSWER24 DELAYED32 BLACKLISTED33 FAX35 DATA83 LINE IN USE
Reference InformationSafety InformationReference Guide 97Safety InformationPower cordsThe power cord supplied with the notebook AC adapter should match the plug andvoltage requirements for your local area. Regulatory approval for the AC adapter hasbeen obtained using the power cord for the local area. However, if you travel to adifferent area or need to connect to a different outlet or voltage, you should use oneof the power cords listed below. To purchase a power cord (including one for an areanot listed below) or a replacement AC adapter, contact your local authorized dealeror Sales and Service office. For any power cord with a fused plug, if you have toreplace the fuse, be sure to install an approved fuse.Country or Region Rated Voltage and CurrentCanadaMexicoPhilippinesTaiwanUnited States125 Vac (3 A)East and West EuropeEgyptSaudi Arabia250 Vac (2.5 A)Hong KongSingaporeUnited Kingdom250 Vac (2.5 A)AustraliaNew Zealand250 Vac (2.5 A)Japan 125 Vac (3 A)India 250 Vac (2.5 A)South Africa 250 Vac (2.5 A)Argentina 250 Vac (2.5 A)Chile 250 Vac (2.5 A)China 250 Vac (2.5 A)South Korea 250 Vac (2.5 A)
Reference InformationSafety Information98 Reference GuideBattery safety• To avoid risk of fire, burns, or damage to your battery pack, do not allow a metalobject to touch the battery contacts.• Do not disassemble the battery. There are no serviceable parts inside. Do notdispose of the battery pack in fire or water.• Handle a damaged or leaking battery with extreme care. If you come in contactwith the electrolyte, wash the exposed area with soap and water. If it contacts theeye, flush the eye with water for 15 minutes and seek medical attention.• Do not expose the battery pack to storage temperatures above 60 °C (140 °F).• When discarding a battery pack, contact your local waste disposal providerregarding local restrictions on the disposal or recycling of batteries.• To obtain a replacement battery, contact your local dealer or sales office.• Do not charge the battery pack if the ambient temperature exceeds 45 °C(113 °F).• Replace only with the same or equivalent type battery pack recommended by themanufacturer.• This product contains a lithium-ion or nickel-metal-hydride battery and mayrequire special handling at end-of-life.Laser safetyThe CD-ROM and DVD drives used with the computer are certified as a Class 1laser devices according to the U.S. Department of Health and Human Services(DHHS) Radiation Performance Standard and International Standards IEC 825 /IEC 825-1 (EN60825 / EN60825-1). These devices are not considered harmful, butthe following precautions are recommended:• Ensure proper use by reading and following the instructions carefully.
Reference InformationSafety InformationReference Guide 99• If the unit requires service, contact an authorized service center.• Do not attempt to make any adjustment of the unit.• Avoid direct exposure to the laser beam—do not open the unit.CLASS 1 LASER PRODUCTLASER KLASSE 1LED safetyThe infrared port located on the front of certain models is classified as a Class 1LED (light-emitting diode) device according to International Standard IEC 825-1(EN60825-1). This device is not considered harmful, but the following precautionsare recommended:• If the unit requires service, contact an authorized service center.• Do not attempt to make any adjustment of the unit.• Avoid direct eye exposure to the infrared LED beam. Be aware that the beam isinvisible light and cannot be seen.• Do not attempt to view the infrared LED beam with any type of optical device.CLASS 1 LED PRODUCTLEDSCHÜTZKLASSE 1 PRODUKTMercury safetyThis product contains mercury in the fluorescent lamp of the liquid-crystal display,and may require special handling at end-of-life.
Reference InformationSafety Information100 Reference GuideExposure to radio frequency radiationThe radiated output power of the IEEE 802.11 and Bluetooth internal wireless radiois far below the FCC radio frequency exposure limits. Nevertheless, the wirelessradio shall be used in such a manner that the potential for human contact duringnormal operation is minimized.The internal wireless radio operates within guidelines found in radio frequencysafety standards and recommendations, which reflect the consensus of the scientificcommunity. We therefore believe the internal wireless radio is safe for use byconsumers. The level of energy emitted is far less than the electromagnetic energyemitted by wireless devices such as mobile phones. However, the use of wirelessradios may be restricted in some situations or environments, such as aboardairplanes. If you are unsure of restrictions, you are encouraged to ask forauthorization before turning on the wireless radio.
Reference InformationRegulatory InformationReference Guide 101Regulatory InformationThis section presents information that shows how your computer complies withregulations in certain regions. Any modifications to your computer not expresslyapproved by the manufacturer could void the authority to operate the computer inthese regions.U.S.A.This computer has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residentialinstallation.This computer generates, uses, and can radiate radio frequency energy. If notinstalled and used in accordance with the instructions, it may cause harmfulinterference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this computer does causeharmful interference to radio or television reception (which can be determined byremoving the unit’s batteries and AC adapter), try the following:• Reorienting or relocating the receiving antenna.• Relocating the computer with respect to the receiver.• Connecting the computer’s AC adapter to another power outlet.Connections to Peripheral DevicesTo maintain compliance with FCC Rules and Regulations, use properly shieldedcables with this device.For more information, consult your dealer, an experienced radio/televisiontechnician, or the following booklet, prepared by the Federal CommunicationsCommission: How to Identify and Resolve Radio-TV Interference Problems.This booklet is available from the U.S. Government Printing Office,Washington, DC 20402, Stock Number 004-000-00345-4. At the first printing ofthis manual, the telephone number was (202) 512-1800.This equipment complies with Part 68 of the FCC rules and the requirements adoptedby the ACTA. On the bottom of the computer or on the modem is a label thatcontains, among other information, a product identifier in the formatUS:AAAEQ##TXXXX. If requested, this information must be provided to thetelephone company.
Reference InformationRegulatory Information102 Reference GuideApplicable certification jack USOC = RJ11C. A plug and jack used to connect thisequipment to the premises wiring and telephone network must comply with theapplicable FCC Part 68 rules and requirements adopted by the ACTA. A complianttelephone cord and modular plug is provided with this product. It is designed to beconnected to a compatible modular jack that is also compliant. See installationinstructions for details.The REN is used to determine the number of devices that may be connected to atelephone line. Excessive RENs on a telephone line may result in the devices notringing in response to an incoming call. In most but not all areas, the sum of RENsshould not exceed five (5.0). To be certain of the number of devices that may beconnected to a line, as determined by the total RENs, contact the local telephonecompany. For products approved after July 23, 2001, the REN for this product is partof the product identifier that has the format US:AAAEQ##TXXXX. The digitsrepresented by ## are the REN without a decimal point (for example, 03 means theREN is 0.3). For earlier products, the REN is separately shown on the label.If this equipment causes harm to the telephone network, the telephone company willnotify you in advance that temporary discontinuance of service may be required. But,if advance notice isn't practical, the telephone company will notify the customer assoon as possible. Also, you will also be advised of your right to file a complaint withthe FCC if you believe it is necessary.The telephone company may make changes to its facilities, equipment, operations orprocedures that could affect the operation of the equipment. If this happens thetelephone company will provide advance notice in order for you to make necessarymodifications to maintain uninterrupted telephone service.If trouble is experienced with this equipment, call 1-800-652-6672. If the equipmentis causing harm to the telephone network, the telephone company may request thatyou disconnect the equipment until the problem is resolved. You should onlyperform repairs to the equipment specifically discussed in the troubleshootingsection of the user guide.Connection to party line service is subject to state tariffs. Contact the state publicutility commission, public service commission or corporation commission forinformation.If your home has specially wired alarm equipment connected to the telephone line,ensure the installation of this computer equipment does not disable your alarmequipment. If you have questions about what will disable alarm equipment, consultyour telephone company or a qualified installer.
Reference InformationRegulatory InformationReference Guide 103The Telephone Consumer Protection Act of 1991 makes it unlawful for any personto use a computer or other electronic device, including fax machines, to send anymessage unless such message clearly contains in a margin at the top or bottom ofeach transmitted page or on the first page of the transmission, the date and time it issent and an identification of the business or other entity, or other individual sendingthe message and the telephone number of the sending machine or such business,other entity, or individual. (The telephone number provided may not be a 900number or any other number for which charges exceed local or long-distancetransmission charges.)Declaration of Conformity (U.S.A.)Responsible Party: Hewlett-Packard CompanyManager of Corporate Product Regulations3000 Hanover StreetPalo Alto, CA 94304+1 (650) 857-1501declares that the product(s)Trade name: Hewlett-Packard CompanyProduct name: Pavilion ZE4... and XT... seriesRegulatory Model Number: CRVSA-02T1-75Complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions:1. This device may not cause harmful interference, and2. This device must accept any interference received, including interference thatmay cause undesired operation.CanadaThis digital apparatus does not exceed the Class B limits for radio noise emissionsfrom digital apparatus as set out in the radio interference regulations of the CanadianDepartment of Communications. This equipment meets the applicable IndustryCanada technical specifications.The Ringer Equivalence Number, REN, is an indication of the maximum number ofdevices allowed to be connected to a telephone interface. The termination on aninterface may consist of any combination of devices subject only to the requirementthat the sum of the RENs of all devices does not exceed five. The REN for thisterminal equipment is 1.0.
Reference InformationRegulatory Information104 Reference GuideThe internal wireless radio complies with RSS 210 of Industry Canada. To preventradio interference to the licensed service, this device is intended to be operatedindoors and away from windows to provide maximum shielding. Equipment (or itstransmit antenna) that is installed outdoors is subject to licensing.Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant leslimites applicables aux appareils numériquesdeClasseBprescritesdanslerèglement sur le brouillage radioélectrique édictépar le Ministère desCommunications du Canada. Le composant RF interne est conforme àla normeCNR-210 d’Industrie Canada. L’utilisation de ce dispositif est autoriséeseulementaux conditions suivantes : (1) il ne doit pas produire de brouillage et (2) l’utilisateurdu dispositif doit étre prétàaccepter tout brouillage radioélectrique reçu, même si cebrouillage est susceptible de compromettre le fonctionnement du dispositif.European UnionThe equipment has been approved in accordance with Council Decision 98/482/ECfor pan-European single terminal connection to the public switched telephonenetwork (PSTN) and to a radio-frequency wireless network. However, due todifferences between the individual PST’s provided in different countries, theapproval does not, of itself, give an unconditional assurance of successful operationon every PSTN network termination point.In event of problems, you should contact your equipment supplier in the firstinstance.This equipment has been designed to work in all of the countries of the EuropeanEconomic Area (Public Switched Telephone Networks). Network compatibility isdependent on internal software settings. Contact your equipment supplier if it isnecessary to use the equipment on a different telephone network.Belgium: For outdoor usage only channels 10 (2457 MHz) through 13 (2472 MHz)are allowed. For private usage outside buildings across public grounds over less than300m, no special registration with IBPT/BIPT is required. Registration toIBPT/BIPT is required for private usage outside buildings across public grounds overmore than 300m. An IBPT/BIPT license is required for public usage outsidebuilding. For registration and license please contact IBPT/BIPT.France: Restricted frequency band: only channels 10 through 13 (2457 MHzthrough 2472 MHz respectively) may be used in France. License required for everyinstallation, indoor and outdoor installations. Please contact ART for the procedureto follow. Use with outdoor installations not allowed.
Reference InformationRegulatory InformationReference Guide 105Germany: License required for outdoor installations. Check with reseller forprocedure to follow.Netherlands: License required for outdoor installations. Check with reseller forprocedure to follow.Italy: Indoor or outdoor use in a public area requires a user license.Die Geräte wurden gemäß Ratsentscheidung 98/482/EC für den Anschluss an eineeinzelne Telefonbuchse im europäischen Raum (Public Switched TelephoneNetwork) und drahtlose Funknetzwerke zertifiziert. In Anbetracht der Unterschiedezwischen den einzelnen Telefonnetzen bietet die Zertifizierung für sich genommenkeine absolute Sicherheit, dass die Geräte bei Anschluss an jeder beliebigenTelefonbuchse funktionieren.Sollten Probleme auftreten, wenden Sie sich zunächst an den Gerätehersteller. DieseGeräte wurden zum Betrieb in allen Ländern der europäischen Wirtschaftsgemein-schaft entwickelt (Public Switched Telephone Networks). Die KompatibilitätzumNetz ist von internen Software-Einstellungen abhängig. Wenden Sie sich an denGerätehersteller, wenn Sie die Geräte in einem anderen Telefonnetz einsetzenmüssen.Cet équipement a étéreconnu conforme aux décisions du Conseil 98/482/ECrelatives àla connexion pan-européenne de terminal simple au réseau téléphoniquepublic commuté(RTPC) et àun réseau sans fil RF. Cependant, des différencesexistant entre les RTPC nationaux présentsdanslesdifférents pays, cettehomologation en elle-même ne garantit pas la réussite de toutes les opérations surtous les points de terminaison du réseau téléphonique public commuté.En cas de problème, prenez contact avec le fournisseur auprès duquel vous vous êtesprocurévotre équipement.Cet équipement a étéconçu pour fonctionner dans tous les pays membres de la zoned'échange européenne (Réseaux Téléphoniques Public Commutés). La compatibilitéentre réseaux dépend des paramètres internes du logiciel. Prenez contact avec lefournisseur auprès duquel vous vous êtes procurévotre équipement pour savoir s'ilest préférable d'utiliser ce dernier sur un autre réseau téléphonique.Questa apparecchiatura èstata approvata in conformitàalla Decisione del Consiglio98/482/EC che regolamenta, in seno all’Unione Europea, la connessione di singoliterminali alla rete telefonica pubblica commutata (PSTN) e alla rete wireless in radiofrequenza. Tuttavia, a causa delle differenze esistenti tra i singoli servizi PSTNforniti nei diversi paesi, l’approvazione in séstessa non rappresenta una garanziaassoluta di funzionamento su ogni singolo punto di terminazione della rete PSTN.
Reference InformationRegulatory Information106 Reference GuideIn caso di problemi, per prima cosa rivolgersi al fornitore dell’apparecchiatura.Questa apparecchiatura èstata progettata per funzionare in tutti i paesi dell’AreaEconomica Europea (reti telefoniche pubbliche commutate). La compatibilitàdellarete dipende dalle impostazioni interne del software. Rivolgersi al fornitoredell’apparecchiatura qualora sia necessario utilizzare quest’ultima su una retetelefonica diversa.JapanJapan Telecommunications ApprovalName of Equipment: AMC20493-001-KT5TELEC approval number: D02-0005JPName of Equipment: T60H424
Reference InformationRegulatory InformationReference Guide 107New ZealandConexant AMC20493 Data Fax ModemPTC 211/02/071PTC200 General WarningThe grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the itemcomplies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom,nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in allrespects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product iscompatible with all of Telecom's network services.PTC200 2.11.1 (6) & (7) Compliance Testing (Functional tests)This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it isdesigned. Telecom will accept no responsibility should difficulties arise in such circumstances. This condition typicallyapplies to 56 kbit/s modems.PTC200 4.5.1 (4) Off-hook Line ImpedanceThis equipment does not fully meet Telecom’s impedance requirements. Performance limitations may occur when usedin conjunction with some parts of the network. Telecom will accept no responsibility should difficulties arise in suchcircumstances.PTC200 5.6.1 (3) General Requirements (automatic dialing devices)This equipment shall not be set up to make automatic calls to Telecom’s 111 Emergency Service.PTC200 7.5.2 (3) (4) Ringer SensitivityThis device may be subject to ringing or bell tinkle when certain other devices are connected to the same line. If thisoccurs, the problem should not be referred to the Telecom Faults Service.Associated Software Limits of ComplianceSome parameters required for compliance with Telecom’s Telepermit requirements are dependent on the applicationsoftware or PC equipment associated with this device. The application software shall be set to operate within thefollowing limits for compliance with Telecom’s specifications:The S0 register must contain a value of 0 for no auto-answer or a value of 2 for auto-answer.The S6 register must contain a value of 2, 3, 4, 5, 6, or 7. The factory default of 2 is recommended.The S7 register must contain a value less than 90. The factory default of 72 is recommended.The S10 register must contain a value less than 150. The factory default of 14 is recommended.The S11 register must contain a value greater than 60. The factory default of 95 is recommended.There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manualcall initiation.The equipment shall go on-hook for a period of not less than 30 seconds between the end of one call attempt and thebeginning of the next attempt to the same number.Automatic calls to different numbers shall be not less than 2 seconds apart.Failure to set these parameters correctly could negate the User Rights under the Telecom Terms of Service.
Reference InformationRegulatory Information108 Reference GuideRussiaInternationalProducts sold internationally by the manufacturer and its authorized dealers meet thespecifications listed on the following page.Note For regulatory identification purposes, your product is assigned a Regulatory ModelNumber. The Regulatory Model Number for your product is listed in the declarationbelow. This regulatory number is different from the marketing name and productnumber.
Reference InformationRegulatory InformationReference Guide 109Declaration of Conformity (according to ISO/IEC Guide 22 and EN 45014)Manufacturer’s Name:Manufacturer’sAddress:Hewlett-Packard Company, Personal Systems Group19310 Pruneridge Ave., Cupertino, CA 95014, U.S.A.declares that the following productProduct Name: HP Notebook PCsRegulatory ModelNumber:Product Options:CRVSA-02T1-75Includes all options for analog modems (Conexant) and 802.11b RF devices (Ambit)conforms to the following product specificationsSafety: IEC 60950: 1991 +A1,A2,A3,A4 / EN 60950: 1992 +A1,A2,A3,A4,A11IEC 60825-1: 1993 +A1 / EN 60825-1: 1994 +A11 Class 1 LEDGB4943-1995EMC: EN 55022: 1994 +A1: 1995 +A2: 1997, Class B [1]CISPR 24: 1997 / EN 55024: 1998IEC 61000-3-2: 1995 / EN 61000-3-2:1995 +A1: 1998 +A2: 1998IEC 61000-3-3: 1994 / EN 61000-3-3:1995GB9254-1998FCC Title 47 CFR, Part 15 Class B/ANSI C63.4: 1992AS/NZS 3548: 1995 Rules and Regulations of Class BTelecom: TBR 21: 1998, EG 201 121: 1998Radio:Equipment Class 2EN 301 489-17: 2000 Specific conditions for wideband data HYPERLAN equipmentEN 300 328-2: 2000 Technical requirements for Radio equipmentNotified Body Number: 0682Notified Body Address: CETECOM ICT Services GmbH, Untertuerkheimer Str. 6-10, D-66117 SaarbrueckenSupplementaryInformation:The product herewith complies with the requirements of the R&TTE Directive 1999/5/EC and carriesthe CE marking accordingly.[1] The product was tested in a typical configuration with Hewlett-Packard Personal Computerperipherals.This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2) this device must accept anyinterference received, including interference that may cause undesired operation.The HP F1454, F1781, F4600, F4814, F4813, F5104, 5950-4334, and 5950-4359 ac/dc adaptersused with this product are designed to operate on all power systems, other than IT power systems.Corvallis, OR, July 17,2002European Contact for regulatory topics only: Hewlett Packard GmbH, HQ-TRE, Herrenberger Strasse 140, 71034Boeblingen, Germany. Fax: +49 7031 143143.USA Contact: Hewlett Packard Co., Corporate Product Regulations Manager, 3000 Hanover Street, Palo Alto, CA94304, U.S.A. Phone: +1 (650) 857-1501.
Reference Guide 111IndexAAC adaptercompatibility, 11, 55connecting, 11AC adapter jack, location, 5AdHoc wireless network setup, 41adjustingbrightness, 19volume, 19airplanes, wirelesscommunication in, 42, 44ALT GR key, 21antistatic precautions, 58, 60Applications key, 21AT commands, 38audioadjusting volume, 66troubleshooting, 66volume, 19audio jacks, 3audio mute button, 3Bbatterybest use of, 34checking status, 32extending life of, 34installing, 10location, 2, 3low power warning, 33operating time, 34, 78release latch, 6, 7safety, 98saving power, 34status lights, 32troubleshooting, 77BIOS password, 24BIOS Setup utilityBoot menu, 87Exit menu, 87external display settings, 86Main menu, 85Security menu, 86using, 84black list (modem), 37blackout periods, modem, 37Bluetoothbusiness cards, 46configuring, 45sending files, 46troubleshooting, 82tuning on, 44turning off, 45wireless, 44boot device order, 17, 87Boot menu (BIOS), 87brightness, adjusting, 19business cards, 46CCable lock, 25Caps Lock, 9Cardbus cards, 48cards, PCMCIA, 48CD-ROM drivecreating or copying CDs, 23inserting CD, 20, 22location, 2, 3removing CD, 20, 22CDscopying/creating, 23recommended media, 23cleaning the notebook, 28configuringBIOS settings, 84modem, 38connectingIEEE 1394 devices, 53LAN, 39wireless network, 40Ddata protection, 28DDR-266 RAM, 58, 73default BIOS settings, 85devicesboot order, 87temporary boot order, 17diskette drivelocation, 5USB, 81displayBIOS settings, 86brightness, 19, 28, 34dual display, 53dual monitor, 53extending life, 28memory, 85port, 5secondary, 53troubleshooting, 68docking port, 6, 7driveshard drive holder, 63replacing hard drive, 62DVD drivelocation, 2, 3setting region code, 23troubleshooting, 67Eencryption, 40ergonomics, 10Exit menu (BIOS), 87extended memory, 85external monitor port, 5FFn key+ Back Space (mute), 19+ F1 (decrease brightness), 19+ F12 (hibernation), 19+ F2 (increase brightness), 19+ F8 (keypad), 19+ NumLock (scroll lock), 19+ Page Down (decrease audio),19+ Page Up (increase audio), 19Hhard drivecaringfor,28Hibernation partition, 62, 87holder, 63location, 6, 7protecting, 27replacing, 62troubleshooting, 69Hibernationstatus lights, 8
112 Reference GuideHibernation modedefinition, 16Hibernation partition, 62, 87hot keys, 19hot notebook, 70IIEEE 1394 portconnecting devices, 53location, 5infrared communicationtroubleshooting, 70infrared portlocation, 2, 3printing, 54safety, 99troubleshooting, 70insertingCD, 20, 22DVD, 20, 22PC card, 48installingbattery, 10hard drive, 62hard drive holder, 63Internet Service Provider, 36Kkeyboardergonomic precautions, 10non US, 21status lights, 2, 3, 9troubleshooting, 71Keypad Lock, 2, 3, 9LLANconnecting to, 39troubleshooting, 72wireless, 40LAN portindicator lights, 39location, 5laser safety, 98lightsLAN port, 39status,2,3,8,9locking notebook, 24LPT1 port, 5MMain menu (BIOS), 85maintenancenotebook configuration, 84software installation, 88memoryextended, 85PC2100 DDR-266, 58, 73troubleshooting, 73video, 85Mini PCI location, 6, 7modemAT commands, 38black list, 37blackout periods, 37built-in, 12port location, 5settings, 38software, 36troubleshooting, 73monitorBIOS settings, 86port, 5resolution, 53mouse, troubleshooting, 71mute buttonlocation, 3Nnetworkconnecting to, 39LAN, See LANwireless, See wireless networkNorton AntiVirus, 25notebookcaringfor,27changing BIOS settings, 84cleaning, 28opening/closing, 2, 3protecting, 27, 70resetting, 17timeouts, 31turning on, 13Num Lock, 9Ooffbutton location, 2, 3status lights, 8turning off, 16on button, location, 2, 3One-Touch buttonslocation, 2, 3using, 20overheating, 70Pparallel portlocation, 5troubleshooting, 80password, 24PC card slot, location, 5PC cardsinstalling, 48saving power, 34stopping, 49troubleshooting, 76PC2100 DDR-266 RAM, 58, 73PCMCIA cards, 48phone cord, connecting, 12plug requirements, 97port locations, 5powerconnecting AC, 11saving, 34troubleshooting, 77power buttonlocation, 2, 3resetting with, 17power cords, 97power managementautomated, 30schemes, 31printinginfrared printers, 54troubleshooting, 79protectionCable lock, 25Norton AntiVirus, 25PS/2 port, 2, 5QQuick Lock, 24QuickRestore System RecoveryCDusing, 88RRAMlocation, 6, 7PC2100 DDR-266, 58, 73
Reference Guide 113rebootingboot device, 87temporary boot device, 17region code, 23regulatory information, 101removingCD, 20, 22DVD, 20, 22hard drive, 62hard drive holder, 63PC card, 49reset button, 17resetting, 17Ssafetybattery use, 98infrared port, 99laser, 98power cords, 97wireless communication, 42, 44safety information, iiisaving battery power, 34scroll pad, 3scroll pad, 2secondary display, 53securitycable lock, 5Cable lock, 25Norton AntiVirus, 25Security menu (BIOS), 86serial porttroubleshooting, 80setting up, 10Standbyand display life, 28resuming and, 82saving power, 34status lights, 8troubleshooting, 82Standby modedefinition, 16timeout, 16startup, troubleshooting, 81static electricity, 58, 60status lightsbattery charge, 32keyboard, 2, 3, 9location, 2, 3meanings, 8S-Video port, 5Ttemperature, overheating, 701394 devices, connecting, 531394 port, 53timeouts, notebook, 31TouchPadlocation, 2, 3troubleshooting, 71troubleshootingaudio, 66battery, 77CD/DVD drive, 67display, 68hard drive, 69infrared communications, 70keyboard, 71LAN, 72memory, 73modem, 73overheating, 70parallel port, 80PC card, 76performance, 76pointing devices, 71power, 77printing, 79resuming, 82serial port, 80Standby, 82startup, 81USB, 80wireless communication, 82turning on notebook, 13typing special characters, 21UUSBdiskette drive, 81port location, 5third port location, 3troubleshooting, 80Vventilation, 27, 70video memory, 85virus protection, 25voltage requirements, 97volumeadjusting, 19troubleshooting, 66volume control, 3WWindowskey, 21password, 24setting up, 13wireless communicationBluetooth, 44configuring (Bluetooth), 45indicator light, 2, 3, 42, 44on-off button, 40restrictions on use, 42, 44status, 42troubleshooting, 82turning off (Bluetooth), 45turning on, 42turning on (Bluetooth), 44wireless networkAdHoc, 41connecting to, 40

Navigation menu