Broadcom BRCM1002-H 802.11b WLAN Mini-PCI Module User Manual Regulatory and Safety Notices

Broadcom Corporation 802.11b WLAN Mini-PCI Module Regulatory and Safety Notices

UserManual.wiki >

BRCM1002-H User Manual >

CRN 10069 Q2 HP PP2180 user manual Regulatory statement

Contents

1. User Manual
2. CRN 10069 Q2 HP CRVSA 02T1 75 user manual
3. CRN 10069 Q2 HP PP2180 user manual 1 of 2
4. CRN 10069 Q2 HP PP2180 user manual 2 of 2
5. CRN 10069 Q2 HP PP2180 user manual Regulatory statement
6. CRN 9475 Q1 notebook user manual
7. CRN 10072 Q3 notebook user manual
8. CRN 10072 Q3 regulatory info
9. CRN 10072 Q3 Wireless regulatory info

CRN 10069 Q2 HP PP2180 user manual Regulatory statement

Regulatory and Safety NoticesDocument Part Number: 339645-001August 2003This guide provides governmental agency notices concerning wireless communication and all other governmental agency information. Instructions for preventing damage from electrostatic discharge are also included.339645-001.book Page i Wednesday, May 28, 2003 12:47 PM

© 2003 Hewlett-Packard Development Company, L.P.The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting and additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.Regulatory and Safety NoticesFirst Edition August 2003Document Part Number: 339645-001339645-001.book Page ii Wednesday, May 28, 2003 12:47 PM

iv Regulatory and Safety NoticesContentsWireless Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–14European Union Notice . . . . . . . . . . . . . . . . . . . . . . . . . 1–15Japanese Regulatory Wireless Notice . . . . . . . . . . . . . . 1–16Brazilian Regulatory Wireless Notice . . . . . . . . . . . . . . 1–172 Electrostatic DischargePreventing Electrostatic Discharge . . . . . . . . . . . . . . . . . 2–1Handling Drives. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–1Handling Internal Components . . . . . . . . . . . . . . . . . 2–1Grounding Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–2339645-001.book Page iv Wednesday, May 28, 2003 12:47 PM

Regulatory and Safety Notices 1–11Regulatory and WirelessNoticesThis chapter provides all country-specific regulatory notices and compliance information for your notebook including wireless notices.Federal Communications Commission NoticeThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:■Reorient or relocate the receiving antenna.■Increase the separation between the equipment and receiver.■Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.■Consult the dealer or an experienced radio or television technician for help.339645-001.book Page 1 Wednesday, May 28, 2003 12:47 PM

Regulatory and Wireless NoticesRegulatory and Safety Notices 1–3For questions regarding this FCC declaration, write to:Hewlett-Packard CompanyP. O. Box 692000, Mail Stop 510101Houston, TX 77269-2000Or call HP at 281-514-3333.To identify your product, refer to the part, series, or model number found on the product.Canadian NoticeThis Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.Avis CanadienCet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.Japanese NoticeKorean Notice339645-001.book Page 3 Wednesday, May 28, 2003 12:47 PM

1–4 Regulatory and Safety NoticesRegulatory and Wireless NoticesAirline Travel NoticeUse of electronic equipment aboard commercial aircraft is at the discretion of the airline.ÅWARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do not attempt to power the computer with a voltage converter kit sold for appliances.Power Cords NoticeIf you were not provided with a power cord for your notebook or for an external power accessory intended for use with your notebook, you should purchase a power cord that is approved for use in your country.The power cord must be rated for the product and for the voltage and current marked on the product’s electrical ratings label. The voltage and current rating of the cord should be greater than the voltage and current rating marked on the product. In addition, the diameter of the wire must be a minimum of 0.75 mm²/18AWG, and the length of the cord must be between 1.5 m (5 feet) and 2 m (6½ feet). If you have questions about the type of power cord to use, contact your HP authorized service provider.A power cord should be routed so that it is not likely to be walked on or pinched by items placed upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point where the cord exits from the product.Only an AC adapter provided with the notebook, a replacement AC adapter provided by HP, or an AC adapter purchased as an option from HP should be used with the notebook.339645-001.book Page 4 Wednesday, May 28, 2003 12:47 PM

1–6 Regulatory and Safety NoticesRegulatory and Wireless NoticesGerman Ergonomics NoticeHP notebooks bearing the “GS” approval mark meet the applicable ergonomic requirements when used in conjunction with docking bases, keyboards, and monitors that bear the “GS” approval mark. HP notebooks in a stand-alone mode are not intended for continuous use in an office environment.Macrovision Corporation NoticeThis product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other right owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only, unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.Laser Safety NoticesAll HP systems equipped with laser products comply with appropriate safety standards, including IEC 825. With specific regard to the laser, the equipment complies with laser product performance standards set by government agencies for Class 1 laser products. It does not emit hazardous light; the beam is totally enclosed during all modes of customer operation and maintenance.CDRH RegulationsThe Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured from August 1, 1976. Compliance is mandatory for products marketed in the United States.339645-001.book Page 6 Wednesday, May 28, 2003 12:47 PM

Regulatory and Wireless NoticesRegulatory and Safety Notices 1–7ÅWARNING: Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product installation guide may result in hazardous radiation exposure.Laser InformationLaser Type: Semiconductor GaAlAsWave Length: 780 ± 35 nmDivergence Angle: 53.5° ± 1.5°Output Power: Less than 0.2mW or 10,869 W·m-2sr-1Polarization: CircularNumerical Aperture: 0.45 ± 0.04Only authorized technicians trained by HP should attempt to repair this equipment. All troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard.This system is classified as a Class 1 laser product. This label appears on the laser product.339645-001.book Page 7 Wednesday, May 28, 2003 12:47 PM

1–8 Regulatory and Safety NoticesRegulatory and Wireless NoticesModem NoticesImportant Safety InstructionsÅWARNING: When using this device, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:■Do not use this product near water, for example, near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool.■Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.■Do not use this product to report a gas leak in the vicinity of the leak.■Always disconnect the modem cable before opening the equipment enclosure or touching an uninsulated modem cable, jack, or internal component.■If this product was not provided with a telephone line cord, use only No. 26 AWG or larger telecommunication line cord in order to reduce the risk of fire.■Do not plug a modem or telephone cable into the network (RJ-45) jack.SAVE THESE INSTRUCTIONS339645-001.book Page 8 Wednesday, May 28, 2003 12:47 PM

Regulatory and Wireless NoticesRegulatory and Safety Notices 1–9Telecommunications Device ApprovalsThe telecommunications device in your notebook is approved for connection to the telephone network in the countries whose approval markings are indicated on the product label located on the bottom of the notebook or on the modem.Refer to the documentation included with the product to ensure the product is configured for the country in which it is located. Selecting a country other than the one in which it is located may cause your modem to be configured in a way that violates the telecommunication regulations/laws of that country. In addition, your modem may not function properly if the correct country selection is not made. If, when selecting a country, a message appears that states that the country is not supported, this means that the modem has not been approved for use in this country and thus should not be used.U.S. Modem StatementsThis equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of the computer or on the modem is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this information must be provided to the telephone company.Applicable certification jack USOC = RJ11C. A plug and jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord and modular plug is provided with this product. It is designed to be connected to a compatible modular jack that is also compliant. See installation instructions for details.339645-001.book Page 9 Wednesday, May 28, 2003 12:47 PM

1–10 Regulatory and Safety NoticesRegulatory and Wireless NoticesThe REN is used to determine the number of devices that may be connected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. For products approved after July 23, 2001, the REN for this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.If this HP equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But, if advance notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will also be advised of your right to file a complaint with the FCC if you believe it is necessary.The telephone company may make changes to its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted telephone service.If trouble is experienced with this HP equipment, refer to the printed Worldwide Telephone Numbers booklet included with your notebook for information about obtaining customer support. If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. You should only perform repairs to the equipment specifically discussed in the “Troubleshooting” section of the user guide, if one is provided.Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information.339645-001.book Page 10 Wednesday, May 28, 2003 12:47 PM

Regulatory and Wireless NoticesRegulatory and Safety Notices 1–11If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this HP equipment does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business, other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual. (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.)In order to program this information into your fax machine, you should complete the steps outlined in the faxing software instructions.Canadian Modem StatementsThis equipment meets the applicable Industry Canada technical specifications. The Ringer Equivalence Number, REN, is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all devices does not exceed 5. The REN for this terminal equipment is 1.0.339645-001.book Page 11 Wednesday, May 28, 2003 12:47 PM

1–12 Regulatory and Safety NoticesRegulatory and Wireless NoticesNew Zealand Modem StatementsThe grant of a Telepermit for any item of terminal equipment indicates only that Telecom has accepted that the item complies with minimum conditions for connection to its network. It indicates no endorsement of the product by Telecom, nor does it provide any sort of warranty. Above all, it provides no assurance that any item will work correctly in all respects with another item of Telepermitted equipment of a different make or model, nor does it imply that any product is compatible with all of Telecom’s network services.This equipment is not capable, under all operating conditions, of correct operation at the higher speeds for which it is designed. Telecom will accept no responsibility should difficulties arise in such circumstances.If this device is equipped with pulse dialing, note that there is no guarantee that Telecom lines will always continue to support pulse dialing.Use of pulse dialing, when this equipment is connected to the same line as other equipment, may give rise to bell tinkle or noise and may also cause a false answer condition. Should such problems occur, the user should not contact the Telecom Faults Service.This equipment may not provide for the effective hand-over of a call to another device connected to the same line.339645-001.book Page 12 Wednesday, May 28, 2003 12:47 PM

Regulatory and Wireless NoticesRegulatory and Safety Notices 1–13Some parameters required for compliance with Telecom’s Telepermit requirements are dependent on the equipment (PC) associated with this device. The associated equipment shall be set to operate within the following limits for compliance with Telecom’s Specifications:a. There shall be no more than 10 call attempts to the same number within any 30-minute period for any single manual call initiation.b. The equipment shall go on-hook for a period of not less than 30 seconds between the end of one attempt and the beginning of the next attempt.Where automatic calls are made to different numbers, the equipment shall be set to go on-hook for a period of not less than 5 seconds between the end of one attempt and the beginning of the next attempt.The equipment shall be set to ensure that calls are answered between 3 and 30 seconds of receipt of ringing (S0 set between 2 and 10).Voice SupportAll persons using this device for recording telephone conversations shall comply with New Zealand law. This requires that at least one part to the conversation is to be aware that it is being recorded. In addition, the Principles enumerated in the Privacy Act 1993 shall be complied with in respect to the nature of the personal information collected, the purpose for its collection, how it is to be used and what is disclosed to any other party.This equipment shall not be set to make automatic calls to the Telecom ‘111’ Emergency Service.339645-001.book Page 13 Wednesday, May 28, 2003 12:47 PM

1–14 Regulatory and Safety NoticesRegulatory and Wireless NoticesWireless NoticesIn some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the organization. Such restrictions may apply when:■Using the wireless equipment on airplanes, or■The risk of interference to other devices or services is perceived as harmful.If you are uncertain of the policy that applies on the use of wireless equipment in a specific organization or environment (such as airports), you are encouraged to ask for authorization to use this device prior to turning on the equipment.ÅWARNING: Exposure to Radio Frequency Radiation The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the device should be used in such a manner that the potential for human contact during normal operation is minimized. To avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna should not be less than 20 cm (8 inches) during normal operation, including when the notebook display is closed.339645-001.book Page 14 Wednesday, May 28, 2003 12:47 PM

Regulatory and Wireless NoticesRegulatory and Safety Notices 1–15European Union NoticeProducts bearing the CE marking comply with the R&TTE Directive (1999/5/EC), EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. CE compliance of this computer is valid only if powered with an HP provided CE marked AC adaptor.Compliance with these directives implies conformity to the following European Norms (in parentheses are the equivalent international standards and regulations):■EN 55022 (CISPR 22)—Electromagnetic Interference■EN55024 (IEC61000-4-2, 3, 4, 5, 6, 8, 11)—Electromagnetic Immunity■EN61000-3-2 (IEC61000-3-2)—Power Line Harmonics■EN61000-3-3 (IEC61000-3-3)—Power Line Flicker■EN 60950 (IEC 60950)—Product Safety■EN 300 328-2—Technical requirements for radio equipment■EN 301 489-1, -17—General EMC requirements for radio equipment339645-001.book Page 15 Wednesday, May 28, 2003 12:47 PM

1–16 Regulatory and Safety NoticesRegulatory and Wireless NoticesThe IEEE 802.11g wireless LAN functionality of this product may be used in the following EU, EU candidate and EFTA countries: Austria, Belgium, Denmark, Estonia, Finland, Germany, Greece, Hungary, Iceland, Ireland, Italy, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovenia, Spain, Sweden, Switzerland and United Kingdom.For normal wireless LAN operation of this product, only a limited band is available in France (Channels 10, 11, 12 and 13 only). The Autorité de régulation des télécommunications (ART) has special regulations for hotspots allowing other channels too, please check with ART (http://www.art-telecom.fr) on this for local rulings and for authorization.Japanese Regulatory Wireless Notice339645-001.book Page 16 Wednesday, May 28, 2003 12:47 PM

Regulatory and Wireless NoticesRegulatory and Safety Notices 1–17Brazilian Regulatory Wireless NoticeEste equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário.339645-001.book Page 17 Wednesday, May 28, 2003 12:47 PM

Regulatory and Safety Notices 2–12Electrostatic DischargeA discharge of static electricity from fingers or other electrostatic conductors may damage electronic components. Before handling electrostatic-sensitive components, discharge static electricity by using one of the methods described in this chapter.Preventing Electrostatic DischargeHandling DrivesBefore handling a drive, discharge static electricity by touching an exterior unpainted metal surface of a device that is connected to an electrical outlet by a grounding plug.Do not touch the connector pins on a drive or the notebook.Handling Internal ComponentsWhen you are removing or installing internal components, use the following precautions:■Keep components in their electrostatic-safe containers until you are ready to install them.■Have everything needed for the installation within reach so that you do not need to leave the area after beginning the procedure.■Use nonmagnetic tools.339645-001.book Page 1 Wednesday, May 28, 2003 12:47 PM

2–2 Regulatory and Safety NoticesElectrostatic Discharge■Before touching an electronic component, discharge static electricity by using one of the grounding methods described later in this chapter. If you must leave the area during the procedure, remember to reground yourself before resuming the procedure.■Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.■If you remove a component, place it in an electrostatic-safe container.Grounding MethodsIf removal or installation instructions direct you to unplug the notebook, unplug it after being properly grounded and before removing a cover. Use one or both of the following grounding methods:■Touch an exterior unpainted metal surface of a device that is connected to an electrical outlet by a grounding plug.■Use a wrist strap connected by a ground cord to the notebook chassis. Wrist straps are flexible grounding straps with a minimum of one megohm ±10 percent resistance in the ground cords. To provide proper ground, wear the strap snugly against the skin.If you need more information about static electricity or assistance with component removal or installation, refer to the Worldwide Telephone Numbers booklet included with your product for customer support information.339645-001.book Page 2 Wednesday, May 28, 2003 12:47 PM