Brooks Automation UF70 RFID UHF Reader User Manual Installation Guide

Download:
Mirror Download [FCC.gov]
Document ID	1710605
Application ID	yiwX23mVoqDeJuXRzufV5A==
Document Description	Installation Guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	56.49kB (706134 bits)
Date Submitted	2012-05-30 00:00:00
Date Available	2012-05-31 00:00:00
Creation Date	2017-10-31 11:55:35
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-31 11:55:35
Document Title	Installation Guide
Document Creator	FrameMaker 7.2
Document Author:	shertel

English
I n st a lla t ion Gu ide
RFI D Reader UF70 Cert um
The inst allat ion guide m ust be read prior t o inst allat ion. Observe t he safet y inst ruct ions!
St ore for fut ure use! This docum ent at ion is not subj ect t o revisions.
I D120026
02/ 2012
I n for m a t ion
This inst allat ion guide corresponds wit h " Direct ive 1999/ 5/ EC of t he European Parliam ent and t he
Council on radio equipm ent and t elecom m unicat ions t erm inal equipm ent and t he m ut ual
recognit ion of t he conform it y" .
This inst allat ion guide is addressed t o t he com pany owner, who m ust pass it on t o t he personnel
responsible for inst allat ion of t he m achine.
The plant m anager m ust ensure t hat t he inform at ion cont ained in t his inst allat ion guide and in t he
accom panying docum ent s has been read and underst ood.
The m anufact urer does not assum e any responsibilit y for inj uries t o persons or anim als, or dam age t o
propert y or t o t he device arising from incorrect inst allat ion or disregard or insufficient considerat ion of
t he safet y crit eria cont ained in t his inst allat ion guide.
The copyright for t his inst allat ion guide is held solely by
Brooks Aut om at ion ( Germ any) Gm bH
RFI D Division
Gart enst r. 19
95490 Mist elgau
or it s legal successor.
Reproducing or circulat ing t his inst allat ion guide is only perm it t ed wit h t he exclusive
approval of t he copyright holder. This also applies if only excerpt s of t he inst allat ion guide
are copied or circulat ed. These requirem ent s also apply for circulat ing t he inst allat ion guide
in digit al form .
St at us: February 2012
I n for m a t ion
Obj e ct ive s of t he inst a lla t ion guide
This inst allat ion guide cont ains all t he necessary safet y inform at ion t hat m ust be
followed for general safet y and inst allat ion.
This inst allat ion guide including all safet y inform at ion ( as well as all addit ional
docum ent s) m ust be followed, read and underst ood by all persons inst alling t he
device.
Sym bols a n d sign a l w or ds
The following sym bols and signal words are used in t his docum ent at ion. The
com binat ion of a pict ograph and a signal word classifies t he respect ive safet y
inform at ion. The sym bol can vary depending on t he t ype of danger.
Signa l w or d
D e scr ipt ion
D AN GER
This signal word m ust be used if deat h or
irreversible dam age t o healt h can occur if
t he hazard inform at ion is not followed.
W ARN I N G
pr ope r t y da m a ge
Risk of inj ur y a n d
Death
Sym bol
This signal word indicat es bodily inj uries
and propert y dam age including inj uries,
accident s, and healt h risks.
CAUTI ON
This signal word indicat es a risk of
propert y dam age. I n addit ion, t here is a
slight risk of inj uries.
ATTEN TI ON
This signal word warns of m alfunct ions
and m ay only be used if no dam age t o
N o da m a ge
healt h can occur.
I M PORTAN T
This signal word indicat es crossreferences and ways in which operat ions
are facilit at ed. I t excludes all risks of
propert y dam age and inj ury risks.
I n for m a t ion
Ta r ge t gr oup
The inst allat ion guide is addressed t o personnel wit h t he following areas of
responsibilit y:
Ar e a of r e sponsibilit y
Com pe t e nce
I nst allat ion
Specialized personnel
Com m issioning and decom m issioning
I nst ruct ed personnel
Definit ion according t o DI N EN 60204- 1:
I n st r uct e d pe r son n e l:
Persons who have been inst ruct ed and, if required, t rained by a specialist as t o
t he t asks assigned t o t hem , t he possible risks of incorrect behavior and t he
required safet y equipm ent and safet y m easures.
Spe cia lize d pe r sonne l:
Persons who can evaluat e t he work assigned t o t hem and recognize possible risks
based on t heir specialized t raining, knowledge, experience and fam iliarit y wit h
t he relevant st andards.
Fur t he r docum e nt a t ion
For t he RFI D Reader UF70 Cert um a Product Manual is also available. I t cont ains
inform at ion on operat ion, t roubleshoot ing, t ransport and st orage.
Con t e n t s
I de n t ifica t ion ....................................................................................... 7
Sa fe t y I n st r u ct ion s ............................................................................... 9
2 .1
Ar e a of a pplica t ion a nd sym bols
2.1.1
Safet y sym bols – in com pliance wit h 4844- 2
2.1.2
Warning sym bols
10
2.1.3
Prohibit ion sym bols
10
2.1.4
Ot her sym bols
10
2 .2
ESD inst r uct ions
11
2 .3
Re sidua l r isk s
11
2 .4
Addit iona l inst r uct ions
12
Pr odu ct Spe cifica t ion s ........................................................................ 1 3
3 .1
I m a ge s
13
3.1.1
Front view
13
3.1.2
Rear view
14
3.1.3
Top view
15
3 .2
D e scr ipt ion of t he com pon e n t s
16
3 .3
Te ch n ica l da t a
18
3.3.1
Device label
19
I n st a lla t ion ........................................................................................ 2 0
4 .1
Sa fe t y in st r u ct ion s
20
4 .2
Qua lifie d inst a lla t ion pe r sonne l
22
4 .3
Un pa ck ing
22
4 .4
Asse m bly of t h e de vice
23
4 .5
Ant e nna inst a lla t ion
24
4 .6
Pow e r su pply
24
4 .7
Te r m ina l conne ct ion
25
4 .8
Ex t e r na l input a nd out put ( opt iona l)
26
Con t e n t s
4 .9
Com m ission in g
26
4.9.1
Required operat ing condit ions
26
4.9.2
Param et ers of t he serial int erface
26
4.9.3
Param et ers of t he Et hernet int erface
27
Se r vice a n d Tr ou ble sh oot in g .............................................................. 3 0
5 .1
Cust om e r se r vice
30
5 .2
Tr ou ble sh oot in g
31
D ism a n t lin g a n d D isposa l ................................................................... 3 2
6 .1
D ism a nt ling
32
6 .2
D isposa l
32
Cha pt e r 1
I de n t ifica t ion
M ode l
I de n t ifica t ion
RFI D Reader UF70 Cert um
Serial num ber
00 – 0001 – UF70
Part num ber
TUG- E1ML- 4O00- F4- 00E1 ETSI version, prot ect ion class I P40
TFG- E1ML- 4O00- F4- 00E1 FCC version, prot ect ion class I P40
TUG- E1ML- 4O00- R4- 00E1 ETSI version, prot ect ion class I P65
TFG- E1ML- 4O00- R4- 00E1 FCC version, prot ect ion class I P65
M a n u fa ct u r e r
Brooks Aut om at ion ( Germ any) Gm bH
RFI D Division
Gart enst r. 19
95490 Mist elgau
GERMANY
Telephone
+ 49 ( 0) 9279 - 991 550
Fax
+ 49 ( 0) 9279 - 991 501
E- m ail
info.rfid@brooks.com
Websit e
www.brooks- rfid.com
For inform at ion on t he label, see  Device label.
D e cla r a t ion of
confor m it y
I n t he Product Manual of t he RFI D Reader UF70 Cert um you find t he det ailed
wording of t he Europe - CE conform it y.
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
Cha pt e r 1
I de n t ifica t ion
D e sign a t e d u se
This product is exclusively developed for reading and writ ing of passive UHF
t ransponders ( e.g. EPC Class1 Gen2) . Any ot her use of t his device const it ut es
m isuse and renders t he user's aut horit y t o inst all and operat e t he device invalid.
This product is designed t o be m ount ed and operat ed in an indust rial set t ing as a
built- in- device only. I t is not designed t o be used as a st and- alone or port able
device or in a non- indust rial set t ing, such as a household, vehicle or in t he openair.
I nt ended use also includes t he following:
■
following all inst ruct ions in t he inst allat ion guide
■
following all safet y inform at ion
Before inst alling t he device, t he user should ensure t hat t he nat ional approval
requirem ent s for use are m et .
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
Cha pt e r 2
Sa fe t y I n st r u ct ion s
Sa fe t y I n st r u ct ion s
This chapt er gives you an overview of t he following t opics:
■
 Area of applicat ion and sym bols
■
 ESD inst ruct ions
■
 Residual risks
■
 Addit ional inst ruct ions
2 .1
D AN GER
Ar e a of a pplica t ion a n d sym bols
D a nge r t o life , r isk of inj ur ie s or da m a ge t o pr ope r t y
Risks exist when disregarding t he inst allat ion guide and t he safet y inst ruct ions
t herein.
Carefully read t he inst allat ion guide before init ial com m issioning. Perform t he
required safet y m easures before init ial com m issioning.
Follow t he general safet y inform at ion as well as t he special safet y inform at ion
given in ot her chapt ers.
The device was const ruct ed according t o st at e- of- t he- art t echnology and
recognized safet y regulat ions. I n order t o prevent any risks t o life and lim b of t he
user, t hird part ies or dam age t o t he device, only use t he device for it s int ended
purpose and in perfect condit ion wit h regard t o safet y.
Bodily inj uries and/ or propert y dam age result ing from non- com pliance wit h t he
inst ruct ions given in t he inst allat ion guide are t he responsibilit y of t he com pany
operat ing t he device or of t he assigned personnel.
Malfunct ions t hat could com prom ise safet y m ust be elim inat ed im m ediat ely.
2 .1 .1
W ARN I N G
Sa fe t y sym bols – in com plia n ce w it h 4 8 4 4 - 2
Risk of in j u r ie s w h e n disr e ga r ding sa fe t y sym bols
Risks exist when disregarding warnings in t he inst allat ion guide.
Please heed t he warnings.
Special safet y sym bols in accordance wit h DI N 4844- 2 are used in t he corresponding passages in t he t ext of t his inst allat ion guide and require special at t ent ion depending on t he com binat ion of signal word and sym bol.
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
Cha pt e r 2
Sa fe t y I n st r u ct ion s
2 .1 .2
W a r n in g sy m bols
W a r n in g a ga in st
W a r nin g a ga in st
h a za r dou s a r e a
ha za r dous e le ct r ica l
volt a ge
W a r n in g a ga in st
W a r nin g a ga in st
e le ct r om a gne t ic
fla m m a ble m a t e r ia ls
r a dia t ion
W a r n in g a ga in st
W a r nin g a ga in st
pot e nt ia lly e x plosive
e le ct r ost a t ica lly
a t m osph e r e
se nsit ive com pone nt s
2 .1 .3
Pr oh ibit ion sym bols
Una u t h or ize d a cce ss is
Fir e , ope n fla m e a nd
pr oh ibit e d
sm ok ing is pr ohibit e d
Sw it chin g is pr oh ibit e d
Pr oh ibit ion
2 .1 .4
Ot h e r sy m bols
D ispose of pa ck in g
Re cycling
m a t e r ia l a ccor ding t o
r e gula t ions
I m por t a nt in for m a t ion
Re fe r t o m a nua l
D iscon n e ct fr om pow e r
supply
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
10
Cha pt e r 2
Sa fe t y I n st r u ct ion s
2 .2
CAUTI ON
ESD in st r u ct ion s
St at ic elect ricit y can dam age elect ronic com ponent s in t he device. All persons
inst alling t he device m ust be t rained in ESD prot ect ion.
ESD prot ect ive m easures m ust be applied when opening t he device.

Disconnect t he power supply prior t o rem oving or adding com ponent s.

Discharge your body and all t ools used prior t o cont act ing any com ponent s
on t he int erior of t he device!

Touch elect ronically sensit ive part s carefully and at t he corners!
2 .3
Re sidu a l r isk s
Even if all precaut ions have been t aken, t here m ay be unapparent residual risks!
Adhering t o t he safet y inst ruct ions, t he int ended use and t he inst allat ion guide as
a whole can reduce residual risks!
D AN GER
Risk s fr om e le ct r ic cur r e nt
Elect rical energy rem ains in lines, equipm ent and devices even when t he device
is swit ched off.
Only allow qualified elect ricians t o perform work on t he elect rical supply
syst em .
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
11
Cha pt e r 2
Sa fe t y I n st r u ct ion s
2 .4
Addit iona l inst r u ct ions
■
Read and underst and all safet y inst ruct ions prior t o inst alling t he device.
■
This docum ent at ion was writ t en for specifically t rained personnel. The
inst allat ion m ay only be carried out by specifically t rained personnel.
■
Observe all warnings. Follow all warnings on and in t he device and in t he
docum ent at ion.
■
I nst all t he device only in accordance wit h t he m anufact urer's inst ruct ions.
■
Use only t he accessories and cables supplied by t he m anufact urer.
■
Do not connect t he device t o power supplies such as norm al household
elect rical out let s. The device should only be connect ed t o power supplies
as specified in t his docum ent .
■
When rem oving a cable, only pull on t he plug and not on t he cable. Connect cable connect ors st raight and carefully t o avoid dam aging t he cont act s.
■
Never bend t he ant enna cables t oo far or subj ect t hem t o m echanical
forces.
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
12
Cha pt e r 3
Pr odu ct Spe cifica t ion s
Pr odu ct Spe cifica t ion s
This chapt er gives you an overview of t he following t opics:
■
 I m ages
■
 Descript ion of t he com ponent s
■
 Technical dat a
3 .1
I m a ge s
3 .1 .1
Fr on t vie w
Power ( 24 V)
RS232 int erface
Et hernet int erface
4 ant enna port s
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
13
Cha pt e r 3
Pr odu ct Spe cifica t ion s
3 .1 .2
Re a r vie w
4 I / Os
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
14
Cha pt e r 3
Pr odu ct Spe cifica t ion s
3 .1 .3
Top vie w
Ant enna port LED
Mode LED
Test Error LED
Mode but t on
Test OK LED
Reset but t on
Test but t on
Power LED
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
15
Cha pt e r 3
Pr odu ct Spe cifica t ion s
3 .2
D e scr ipt ion of t h e com pon e n t s
Com pone nt
D e scr ipt ion
Power LED
I f t he correct volt age is applied t o t he device, t he
Power LED is green and t he device is operat ional.
Reset but t on
Pressing t his but t on init iat es a power- reset of t he
device. The reset but t on m ust be pressed for at least
t hree seconds unt il all t he LEDs of t he foil keypad
sim ult aneously st art and t he hardware reset is
execut ed.
Mode but t on
I f t he m ode but t on and t he reset but t on are
sim ult aneously pressed at a powerup reset for about
15 seconds unt il all t he LEDs of t he keypad light up for
t he second t im e, t he reader will be reset t o t he default
st at e ( default fact ory set t ing) .
Mode LED
Current ly no use.
Test but t on
Pressing t his but t on swit ches t he device t o t he reading
t est m ode and is used t o select t he ant enna port s. I f
t he but t on is pressed for a longer t im e ( at least 2
seconds) , t hen t he t est m ode is act ivat ed ( Test OK LED
and Test Error LED bot h briefly com e on) or disabled
( Test OK LED and Test Error LED bot h go out ) . Briefly
pressing t he but t ons when t he t est m ode is act ivat ed
result s in swit ching t o t he next ant enna port .
Test OK LED
When a t ransponder in t he t est m ode can be
successfully ident ified, t his LED t urns green.
Test Error LED
When a t ransponder in t he t est m ode cannot be
successfully ident ified, t his LED t urns red.
Ant enna port LED 1
These LEDs signal t he dat a t raffic t o t he respect ive
to 4
ant enna port s. Once dat a is read or writ t en via t he
ant enna port 1 ( above) , t he ant enna port LED 1
( above) t urns green.
Ant enna port LED 1
Port s t o connect t he ant ennas.
to 4
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
16
Cha pt e r 3
Pr odu ct Spe cifica t ion s
Com pone nt
D e scr ipt ion
I / O port s 1 t o 4
A digit al input and out put can be connect ed t o each
ant enna port . A 3 wire sensor or dry cont act is possible
as t he input . The out put can operat e a LED wit hout a
series resist or or direct ly swit ch 5 V DC ( I m ax =
100 m A) .
RS232 int erface
Com m unicat ions wit h t he device can be m ade via t he
serial int erface ( 9 pin sub- D socket ) . Baudrat es of
1,200 Bd up t o 57,600 Bd are possible.
Et hernet int erface
Com m unicat ions wit h t he device can be m ade via t he
10/ 100 Base T int erface.
Volt age supply
Cont act for connect ing t he 24 V DC volt age supply
connect ion
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
17
Cha pt e r 3
Pr odu ct Spe cifica t ion s
3 .3
Te ch n ica l da t a
Te chnica l da t a
Volt age
24 V DC ± 10%
Power consum pt ion
approx. 0.8 A at 24 V
Operat ing t em perat ure
- 20 ° C t o 50 ° C
- 4 ° F t o 122 ° F
St orage t em perat ure
- 40 ° C t o 85 ° C
- 40 ° F t o 185 ° F
Perm issible hum idit y at 50 ° C / 122 ° F
25 – 85%
Prot ect ion class
I P 40 ( opt ional I P 65)
Housing m at erial
Passivat ed alum inum
Weight
approx. 1,500 g
Air int erface
I SO 18000- 6C ( EPC Global Class 1
Gen2)
Frequency range Europe
865 – 868 MHz
Frequency range FCC
902 – 928 MHz
Radiat ion power
< 2 Wat t ERP
Transm it t ing power
program m able in 1 dB st eps
Read / writ e range
up t o 8 m
Serial int erface RS232
1,200 Bd – 57,600 Bd
Et hernet int erface
10/ 100 BaseT
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
18
Cha pt e r 3
Pr odu ct Spe cifica t ion s
3 .3 .1
D e vice la be l
The device label wit h t he CE m ark and part / serial num ber is on t he device
housing.
Part num ber
Serial num ber
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
19
Cha pt e r 4
I n st a lla t ion
I n st a lla t ion
This chapt er gives you an overview of t he following t opics:
■
 Safet y inst ruct ions
■
 Qualified inst allat ion personnel
■
 Unpacking
■
 Assem bly of t he device
■
 Ant enna inst allat ion
■
 Power supply
■
 Term inal connect ion
■
 Ext ernal input and out put ( opt ional)
■
 Com m issioning
Follow t he inst r uct ions in t he sa fe t y cha pt e r
Follow t he general safet y inst ruct ions in t he chapt er  Safet y I nst ruct ions.
4 .1
CAUTI ON
Sa fe t y in st r u ct ion s
The device is designed for indoor use in an indust rial set t ing only.
I nst allat ion is only allowed in an int erior room at a const ant t em perat ure
bet ween - 20 ° C / - 4 ° F and + 50 ° C / 122 ° F, and a relat ive hum idit y bet ween
25% and 85% .
Never use t he device near or in wat er.
Never pour liquids of any t ype over t he device. I f t he device should accident ally
com e in cont act wit h liquid, disconnect it and have it checked by a t echnician.
Do not inst all t he device near heat sources such as radiat ors, heat regist ers,
st oves or ot her devices ( including am plifiers) t hat generat e heat .
Do not inst all t he device in a flam m able environm ent .
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
20
Cha pt e r 4
I n st a lla t ion
CAUTI ON
Never expose t he device t o ext rem e t em perat ure fluct uat ions, since ot herwise
condensat ion develops in t he device and causes dam age.
Do not inst all t he device in t he vicinit y of volt age lines or ot her power lines wit h
which t hey could collide ( for exam ple, when drilling) , which could result in
serious inj uries or even deat h.
The device ( especially t he ant enna) should not be inst alled in t he im m ediat e
vicinit y of elect rical equipm ent such as m edical devices, m onit ors, t elephones,
TV set s, m agnet ic disks and m et al obj ect s.
This could result in reduced read and writ e ranges.
Never use t he device in explosive areas ( such as paint warehouses) .
CAUTI ON
ATTEN TI ON
Do not use t he device in areas where it is exposed t o vibrat ions or shocks.
The inst allat ion locat ion m ust be adequat ely illum inat ed during t he inst allat ion.
Never inst all t he device during a light ning st orm .
Verify t hat t he inst allat ion m eet s t he requirem ent s of t he ( count ry- specific) FCC
for hum an exposure t o radio frequencies.
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
21
Cha pt e r 4
I n st a lla t ion
ATTEN TI ON
When det erm ining t he inst allat ion sit e, keep in m ind t he lengt h of t he ant enna
wire and t he read/ writ e range of t he ant enna used.
4 .2
CAUTI ON
Qua lifie d inst a lla t ion pe r sonne l
I nst allat ion is t o be carried out by specially t rained personnel only. I f you are
uncert ain about t heir qualificat ion, cont act t he m anufact urer.
CAUTI ON
I nst alling t he device wit hout special t raining can result in dam age t o t he reader
and/ or connect ed devices.
4 .3
Un pa ck in g
The device and t he accessories are packed under clean- room condit ions. I n order
t o m aint ain t his condit ion, t he device m ust also be unpacked in clean- room
condit ions.
D isposin g of t h e
pa ck a ging m a t e r ia l
The packaging m at erial consist s of cardboard and foil. Dispose of t hese
m at erials separat ely and observing t he respect ive legal regulat ions of your
count ry.
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
22
Cha pt e r 4
I n st a lla t ion
4 .4
ATTEN TI ON
Asse m bly of t h e de vice
The m ount ing surface m ust be st able, non- flam m able, dry and clean.
I f necessary, clean it before inst alling t he device.
The device m ust be inst alled so t hat air can freely circulat e vert ically t hrough
t he heat sink, and t he operat ing and environm ent al condit ions specified under
 Technical dat a are m et at all t im es.
I nst a lla t ion
dim e n sion s
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
23
Cha pt e r 4
I n st a lla t ion
4 .5
ATTEN TI ON
An t e n n a in st a lla t ion
Consider t he required read and writ e ranges when inst alling t he ant enna. The
reader can only be used properly if t he t ransponder is locat ed wit hin t he
individual reading/ writ ing range of t he respect ive ant enna.
I f t he t ransponder is very close t o t he ant enna, t he t ransponder m ay be
det uned by t he m et al of t he ant enna and a reading/ writ ing is not possible. We
recom m end keeping a m inim um dist ance bet ween t ransponder and ant enna of
about 10 m m .
4 .6
D AN GER
Pow e r su pply
Risk of de a t h fr om da nge r ous volt a ge
Risks exist when supplying t he device wit h t he incorrect volt age.
Only use cables, plugs and adapt ers supplied by t he m anufact urer.
Observe power rat ings of t he t echnical dat a (  Technical dat a) .
The device can be connect ed t o an int ernal power supply of t he syst em or t o an
ext ernal power supply.
Once t he device is connect ed t o t he power supply, t he power LED light s up.
Pin
Sign a l
GND
+ 24 V DC
GND
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
Pins 1 and 3 are bot h grounded.
24
Cha pt e r 4
I n st a lla t ion
4 .7
Te r m ina l conne ct ion
The serial int erface is a Sub- D socket ( 9- pin) .
A norm al RS232 ext ension cable can be used.
Pin
D B9
NC
TxD
RxD
NC
GND
NC
NC
NC
NC
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
25
Cha pt e r 4
I n st a lla t ion
4 .8
Ex t e r na l input a nd out put ( opt ion a l)
The following I / O versions are possible:
A digit al input and out put can be connect ed t o each ant enna port .
A 3 wire sensor or dry cont act is possible as t he input .
The out put can operat e a LED wit hout a series resist or or direct ly swit ch 5 V DC.
4 .9
Com m ission in g
4 .9 .1
Re qu ir e d ope r a t in g con dit ion s
To operat e t he reader, t he following requirem ent s m ust be m et :

An ant enna m ust be connect ed correct ly t o t he reader.

Connect t he power supply and swit ch on t he device ( if a POE is not used) .

The t ransponder m ust be locat ed wit hin t he individual reading/ writ ing
range of t he ant enna ( for t est ing) !
4 .9 .2
Pa r a m e t e r s of t h e se r ia l in t e r fa ce
Baudrat e
57,600
Dat a bit s
St op bit
Parit y
No
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
26
Cha pt e r 4
I n st a lla t ion
4 .9 .3
Pa r a m e t e r s of t h e Et h e r n e t in t e r fa ce
The Et hernet is connect ed via an Et hernet m odule.
Tools are available t hat allow t he Et hernet set t ings t o be configured.
By using Discovery Tools, all Et hernet devices locat ed in t he net work can be
found.
The respect ive device can be configured via a web server and a web browser via a
double click. I f t he TCP / I P address is known, t he web server can also be direct ly
opened in a browser also follows:
ht t p: / / xxx.xxx.xxx.xxx/
Use r : " r oot "
Pa ssw or d: " dbps"
xxx.xxx.xxx.xxx – current ly set I P address
Login
The I P address can be set via t he " net work" link. The set t ings are t ransferred wit h
t he " apply" but t on and t he device is t hen reboot ed.
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
27
Cha pt e r 4
I n st a lla t ion
Con figu r a t ion
I M PORTAN T
The " Fact ory Default Set t ings" m ust not be set under any circum st ances as t hey
are not t he fact ory set t ings of Brooks. Any ot her set t ings of t he Et hernet device
( exept t he I P address) m ust not be changed. Ot herwise a fault- free
com m unicat ion cannot be guarant eed by Brooks.
D igi D e vice
D iscove r y
The t ool displays all devices t hat have a Digi Connect ME. Devices t hat are not in
t he sam e subnet are also displayed. The I P address can be set direct ly via
" configure net work set t ings" . Fixed I Ps or DHCPs are possible. The web server of
t he device can be accessed direct ly via t he " open web int erface" .
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
28
Cha pt e r 4
I n st a lla t ion
Se le ct ion w indow
I n pu t w in dow
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
29
Cha pt e r 5
Se r vice a n d Tr ou ble sh oot in g
Se r vice a n d Tr ou ble sh oot in g
This chapt er gives you an overview of t he following t opics:
■
 Cust om er service
■
 Troubleshoot ing
5 .1
Cust om e r se r vice
Brooks Aut om at ion ( Germ any) Gm bH
RFI D Division
Gart enst r. 19
95490 Mist elgau
GERMANY
Telephone
+ 49 ( 0) 9279 - 991 550
Fax
+ 49 ( 0) 9279 - 991 501
E- m ail
rfid.support @brooks.com
24 hour t echnical support hot line ( Brooks) :
US and Canada
+ 1 978 262 2900
Europe
+ 49 1804 2255 4887
Japan
+ 81 45 477 5980
China
+ 86 21 5131 7066
Taiwan
+ 886 3 5525225
Korea
+ 82 31 288 2500
Singapore
+ 65 6464 1481
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
30
Cha pt e r 5
Se r vice a n d Tr ou ble sh oot in g
5 .2
Tr ou ble sh oot in g
Follow t he inst r uct ions spe cifie d in t he sa fe t y cha pt e r
Follow t he general safet y inst ruct ions in t he chapt er  Safet y I nst ruct ions.

The t ransponder reader and it s com ponent s m ust be serviced by t he
m anufact urer only!

I f errors occur, follow t he inst ruct ions in t he Product Manual of t he RFI D
Reader UF70 Cert um .

I f you are uncert ain about errors and t heir handling, cont act t he
m anufact urer, see  Cust om er service. Have t he serial num ber of t he
t ransponder reader ready as shown on t he label ( see  Device label) when
cont act ing t he m anufact urer!
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
31
Cha pt e r 6
D ism a n t lin g a n d D isposa l
D ism a n t lin g a n d D isposa l
This chapt er gives you an overview of t he following t opics:
■
 Dism ant ling
■
 Disposal
6 .1
D ism a nt ling

Rem ove t he power supply!

Rem ove all cables!

Loosen and rem ove t he m ount ing screws!

Rem ove t he device from t he inst allat ion area!
6 .2
D isposa l
The device and it s com ponent s are m ade of various m at erials.
Dispose of t hese m at erials separat ely, and observing t he legal regulat ions of
your count ry.
Do not dispose of t he device in regular household wast e.
Disconnect t he elect ronic com ponent s from t he case and dispose of t hem as
follows:
■
t he case as scrap m et al
■
t he elect ronic com ponent s, ant ennas and cables as elect ronic wast e
I n st a lla t ion Gu ide - RFI D Re a de r UF7 0 Ce r t u m
32
I n de x
Assem bly 23
Com m issioning 26
Declarat ion of conform it y 7
Device label 19
Et hernet set t ings 27
Hum idit y 20
I nst allat ion dim ensions 23
Malfunct ions 24
Power supply 24
Prohibit ion sym bols 10
Relat ive hum idit y 20
Safet y I nst ruct ions 9
Safet y inst ruct ions 20
Safet y sym bols 9
Serial num ber 19
Sub- D Socket 25
Tem perat ure 20
Warning sym bols 10

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : shertel
Create Date                     : 2012:02:23 12:55:57Z
Keywords                        : Brooks Automation, RFID, Reader, UHF, UF70 Certum, Antenna, Transponder
Modify Date                     : 2012:02:24 08:53:59+01:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Creator Tool                    : FrameMaker 7.2
Metadata Date                   : 2012:02:24 08:53:59+01:00
Format                          : application/pdf
Title                           : Installation Guide
Creator                         : shertel
Description                     : RFID Reader UF70 Certum
Subject                         : Brooks Automation, RFID, Reader, UHF, UF70 Certum, Antenna, Transponder
Producer                        : Acrobat Distiller 9.0.0 (Windows)
Document ID                     : uuid:e8c868ad-090f-4f48-85c2-8d935383d4ef
Instance ID                     : uuid:3c2d8344-2f1a-43f8-bd2e-dc65268e089d
Page Layout                     : SinglePage
Page Mode                       : UseOutlines
Page Count                      : 33

EXIF Metadata provided by EXIF.tools