C H Systems RF-MDWS Door/window Sensors used by Security System User Manual IV

Download:
Mirror Download [FCC.gov]
Document ID	2601433
Application ID	EbPZHm6Epx7Js9gdU5+baw==
Document Description	User Manual IV
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	19.62kB (245308 bits)
Date Submitted	2015-04-30 00:00:00
Date Available	2015-04-30 00:00:00
Creation Date	2014-12-05 10:45:19
Producing Software	Microsoft® Publisher 2010
Document Lastmod	2014-12-05 10:45:19
Document Title	User Manual IV
Document Creator	Microsoft® Publisher 2010
Document Author:	Jim S

RF-MDWSX-Water Micro Wireless Sensor Installation Instruction
Micro Wireless Water Sensor and Accessories
1 - RF-MDWS-Water Sensor 1- Mounting Tape 1 - Water Detector 2 - Batteries ( 2- 3VDC CR 2032) Instructions
Features:
 Water detection when liquid rises above contacts
 Contacts above floor level to prevent false floor condensation detection
 Checks for water every 5 minutes, requires two positive
checks for a valid alarm
Programming:
1. Enter system programming and select Auto Learn Sensors
2. Remover cover from sensor to trip tamper
3. Qolsys panel displays Auto Learn Sensor
4. Press OK
5. Set senor type to Water
6. Select a sensor name
7. Press Add New
8. Exit program or trip next sensor to program
Cover
Latch
Tamper
switch
Batteries
Note: Battery Safety
Observe polarity when inserting replacement batteries to avoid damaging the sensor.
Risk of fire, burns and explosion. Do
not recharge, disassemble, burn or
expose batteries to temperatures
above 100C (212F)
Dispose of used batteries properly
and in accordance with all local laws
Keep batteries away from children
Water
Detector
Doc # I-RF-MDWSX-Water Rev. A
RF-MDWSX-Water Micro Wireless Sensor Installation Instruction
Micro Wireless Water Sensor and Accessories
1 - RF-MDWS-Water Sensor 1- Mounting Tape 1 - Water Detector 2 - Batteries ( 2- 3VDC CR 2032) Instructions
Features:
 Water detection when liquid rises above contacts
 Contacts above floor level to prevent false floor condensation detection
 Checks for water every 5 minutes, requires two positive
checks for a valid alarm
Programming:
1. Enter system programming and select Auto Learn Sensors
2. Remover cover from sensor to trip tamper
3. Qolsys panel displays Auto Learn Sensor
4. Press OK
5. Set senor type to Water
6. Select a sensor name
7. Press Add New
8. Exit program or trip next sensor to program
Cover
Latch
Tamper
switch
Batteries
Note: Battery Safety
Observe polarity when inserting replacement batteries to avoid damaging the sensor.
Risk of fire, burns and explosion. Do
not recharge, disassemble, burn or
expose batteries to temperatures
above 100C (212F)
Dispose of used batteries properly
and in accordance with all local laws
Keep batteries away from children
Water
Detector
Doc # I-RF-MDWSX-Water Rev. A
Installation
FCC label statement:
Specifications:
When mounting the wireless device make sure it is
not mounted on metal or there are any large metal
objects between the device and the control panel,
this can be tested prior to or after installation
Water Detector Mounting:
Mount the sensor as high as possible, the water detector has a 72” cable attaching it to the sensor
The water detector can be mounted to the wall or
floor using mounting screws
Mount sensor
using supplied
hardware
Features:
Detector:
 Dual water sensor probes
 Above floor detection
 72” cable length
Sensor:
 Cover tamper
 Unique ID for each function
 Temperature check every 5
minutes
 Battery checked every hour
“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.”
“Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Batteries:
—Consult the dealer or an experienced radio/TV technician
for help.”
(2) - Panasonic CR2032
Energizer CR2032
Duracell DL2032
“Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment”
“RF Exposure Guidance: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 1.5cm between the radiator and
persons. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter, except
in accordance with FCC multi-transmitter product procedures.”
Detector mounts
directly to the
floor or can be
attached to a wall
Doc # I-RF-MDWSX-Water Rev. A
Installation
FCC label statement:
Specifications:
When mounting the wireless device make sure it is
not mounted on metal or there are any large metal
objects between the device and the control panel,
this can be tested prior to or after installation
Water Detector Mounting:
Mount the sensor as high as possible, the water detector has a 72” cable attaching it to the sensor
The water detector can be mounted to the wall or
floor using mounting screws
Mount sensor
using supplied
hardware
Detector mounts
directly to the
floor or can be
attached to a wall
Features:
Detector:
 Dual water sensor probes
 Above floor detection
 72” cable length
Sensor:
 Cover tamper
 Unique ID for each function
 Temperature check every 5
minutes
 Battery checked every hour
“This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.”
“Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and
receiver.
—Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Batteries:
—Consult the dealer or an experienced radio/TV technician
for help.”
(2) - Panasonic CR2032
Energizer CR2032
Duracell DL2032
“Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate the equipment”
“RF Exposure Guidance: This equipment complies with FCC
radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 1.5cm between the radiator and
persons. This transmitter must not be co-located or operating
in conjunction with any other antenna or transmitter, except
in accordance with FCC multi-transmitter product procedures.”
Doc # I-RF-MDWSX-Water Rev. A

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Page Count                      : 2
Language                        : en-US
Tagged PDF                      : Yes
Author                          : Jim S
Create Date                     : 2014:12:05 10:45:19-06:00
Modify Date                     : 2014:12:05 10:45:19-06:00
Producer                        : Microsoft® Publisher 2010
Creator                         : Microsoft® Publisher 2010

EXIF Metadata provided by EXIF.tools