CARRIER Controls And HVAC Accessories Manual L0601172

User Manual: CARRIER CARRIER Controls and HVAC Accessories Manual CARRIER Controls and HVAC Accessories Owner's Manual, CARRIER Controls and HVAC Accessories installation guides

Open the PDF directly: View PDF PDF.
Page Count: 6

DownloadCARRIER Controls And HVAC Accessories Manual L0601172
Open PDF In BrowserView PDF
Installation
NOTE: Read the entire instruction
installation.

manual

before

starting

the

SAFETY CONSIDERATIONS
Installation

and servicing

of this equipment

ELECTRICAL

can be hazardous

due to mechanical
and electrical components.
and qualified
personnel should install, repair,
equipment.
Untrained

personnel

can perform

basic

tions such as cleaning and replacing
tions must be performed
by trained

Only trained
or service this

maintenance

func-

air filters. All other operaservice personnel. When

working on this equipment,
observe precautions
in the literature, on tags, and on labels attached to or shipped with the
unit and other safety precautions
that may apply.
Follow all safety codes. Installation
must be in compliance
with local and national building codes. Wear safety glasses,
protective
available.

clothing,
and work gloves. Have fire extinguisher
Read these instructions
thoroughly
and follow all

warnings
unit.

or cautions

included

in literature

Instructions

and attached

SHOCK

Failure to follow
injury or death.
Before

this warning

performing

installation,

switch if applicable.
Lock
suitable warning label.

When you see this symbol

on the unit and in instructions

manuals,
be alert to the potential for personal injury. Understand these signal words; DANGER, WARNING,
and CAUTION. These words are used with the safety-alert
symbol.
DANGER identifies the most serious hazards which will result

only. Any frame

switch

with

a

or square

misalignment

will jam damper

duct systems
blades.

3. Install dampers so actuator is visible for inspection and
accessible
in the event it would ever need service.
4. Use sheet metal screws
(do not try to weld

to secure damper

dampers

in ductwork

in any way).

fit and operation
dampers
must be
to ductwork.
Dampers
are made
than

nominal

duct

dimensions

(See

or operation.
Wear safety glasses
available.

and work gloves.

Before proceeding
with installation,
inspect thoroughly
for
shipping damage. Notify shipper immediately
if any damage
is found. Check for proper clearances
of moving parts.
The qualified installer or agency must use factoryauthorized
kits or accessories
when modifying this product. Refer to the
individual
instructions
packaged
with the kits or accessories

UNIT OPERATION

HAZARD

Failure to follow this caution
age or improper operation.

may result in equipment

dam-

Never force dampers into an undersized
duct system.
excess pressure can cause damper blades to jam.

The

installing.
NOTE:

INTRODUCTION

All dampers

according
Slip-in

tag

in rectangular

slightly smaller
Table 1).

when

and

possible. This may help
as dissipate
air noise

is used to identify unsafe practices which may result in minor
personal
injury or product and property damage.
NOTE is
used to highlight suggestions
which will result in enhanced
reliability,

out

near furnace plenum when
ease
installation,
as well
associated
with zoning.

5. To ensure proper
sized according

Follow all safety codes.
Have a fire extinguisher

or maintenance

areas that may be noise
to install zone dampers

in severe personal injury or death. WARNING signifies hazards which could result in personal injury or death. CAUTION

installation,

service

in personal

1. Place dampers
away from
sensitive.
It is recommended

symbol z_.
or

result

INSTALLATION CONSIDERATIONS

2. Install dampers
This is the safety-alert

could

operations
on this system, turn off all main power
switches and/or disconnects.
There may be more than
1 disconnect
switch. Turn off accessory
heater power

to the

Recognize safety information.

HAZARD

style dampers

are designed

for easy

installation

in

rectangular
ductwork on residential new construction
or retrofit applications.
A 24vac, direct-drive
actuator
is used for
smooth, quiet performance.

must be properly

to local codes

or SMACNA

installed

and supported

standards.

Seal duct

joints using duct tape, mastic, or other approved
methods.
not allow mastic to come in contact with actuator.

Do

INSTALLATION
1. To apply

Side Mount

select location
3-in.
opening

or Bottom

wire leads and install on appropriate
Mount

dampers,

OPN (open),

first

for damper to be installed. Cut out a
in 1 side of duct at selected location.

4. In

clearance

holes located

on mounting

(common),
a

duct

condensing,

terminals

system

carefully

may

insulate

5. After

installation

verify
applied
should
damper

plate.

is complete,

they are all operating

check

OPERATION

NOTE:

HAZARD

Failure to follow this caution may
damage or improper operation.

result in equipment

When

airflow

or side mount dampers (or dampers mounted in a horizontal installation),
it may be necessary to additionally
secure damper to avoid drooping
inside duct system
(See Fig. 3). Use extreme caution when inserting screws
in the sides of dampers;
be careful not to bind or damage assembly.
Do not insert screws on the opposite
frame end from actuator assembly;
use side rails to secure.

3. Routefieldwiringtoterminalblock.
to prevent wires from being

Provide strain relief
pulled or snagged.
Strip

and

24vac

is

between
common
and open, the damper
go full open in approximately
15 sec. If the
is used in a 50 Hz application,
time will

Dampers

possible.

are designed

However,

slip-in

noise associated

check damper
For most damper applications
the mounting
plate is sufficient in securing
the damper into the duct system.
However, with larger size dampers
(e.g. 10 in. X 18 in.)

experience
over actuator

dampers

properly.

increase to approximately
18 sec. Power
cycle open / closed several times.
UNIT

labeled:

CLS (close).

assembly
and mounting
plate (check local codes).
Make sure insulation does not interfere with operation
of actuator.

(See Fig. 1 and 2).

through

where

excessive

Ensure opening is fully cut from top to bottom of seam,
this will allow damper to be inserted without obstruction

2. Slide damper
into opening
and check
for proper
alignment.
Secure damper using sheet metal screws

areas

COM

operation

damper

and

to be as quiet and efficient

style dampers
with zoning.

may exhibit

It is recommended

with airflow moving

through

as

some
to

the duct

system.
6. Residential

dampers

are designed

in such

a way that

if the damper
blades should jam or stall it will not
damage
the damper
or motor. If for any reason the
damper should jam, it will usually be related to twisting
or bending of the damper body during installation,
or
tension on the damper shaft. After you correct
any
bending or twisting problems,
damper should operate
properly. If, in an emergency,
it becomes
necessary to
force a damper
disengagement

open manually,
press and hold the
(quick blade release) button with 1

hand and turn mounting
hub to reposition
damper
shaft. Release button to hold damper
shaft in new
position.

f

-2 l,g'

/_

/_T
/

0

C

i !

SIDE RAIL

1_4 "

LISTED

\ °
I

i/

QUICK BLAr)E
RELEASE BUTTON

(RED)
A05249

Fig. 1 - Side-Mount

Damper Configuration

B

i

O

_

LISTED

Z_--_

DAMPER
WIDTH
-----

©O

_1
\_"

"_

_

"_--

QUICK
RELEASE

--

--

_

I

BLADE
BUTTON

(RED)

AO5248

Fig. 2 - Bottom-Mount

Damper Configuration

Table 1--Slip-In
Catalog number
DAM PSLS08X08- B
DAMPSLB08X08-B

Damper

Dimensions

Description
SIDE MOUNT 8X8

(In,)
A

B

7 13/16
7 13/16

7 13/16
7 13/16

9 7/8

7 13/16

DAM PSLS08Xl 0 - B

BOTTOM MOUNT 8X8
SIDE MOUNT 8X10

DAM PSLB08Xl

BOTTOM MOUNT 8X10

7 13/16

9 7/8

SIDE MOUNT 8X12

11 7/8

7 13/16

2- B

BOTTOM MOUNT 8X12

7 13/16

11 7/8

DAM PSLS08Xl 4 - B
DAMPSLB08X14-B

SIDE MOUNT 8X14
BOTTOM MOUNT 8X14

13 7/8
7 13/16

7 13/16
13 7/8
7 13/16

0- B

DAM PSLS08Xl 2- B
DAM PSLB08Xl

DAM PSLS08Xl 6 - B
DAMPSLB08X16-B
DAM PSLS08Xl 8 - B
DAMPSLB08X18-B

SIDE MOUNT 8X16

15 7/8

BOTTOM MOUNT 8X16

7 13/16

15 7/8

SIDE MOUNT 8X18

17 7/8
7 13/16

7 13/16
17 7/8

DAM PSLS08X20-

B

BOTTOM MOUNT 8X18
SIDE MOUNT 8X20

7 13/16

19 7/8

DAM PSLB08X20-

B

BOTTOM MOUNT 8X20

19 7/8

7 13/16

SIDE MOUNT 8X22

7 13/16

21 7/8

DAM PSLB08X22-

B

BOTTOM MOUNT 8X22

21 7/8

7 13/16

DAMPSLS08X24-B
DAM PSLB08X24-

B

SIDE MOUNT 8X24
BOTTOM MOUNT 8X24

7 13/16
23 7/8

23 7/8
7 13/16
9 13/16

DAMPSLS08X22-B

DAMPSLSl0Xl0-B

SIDE MOUNT 10X10

9 7/8

DAMPSLB10Xl0-B

BOTTOM MOUNT 10X10

9 13/16

9 7/8

SIDE MOUNT 10X12

11 7/8
9 13/16

9 13/16
11 7/8

13 7/8

9 13/16

DAM PSLSl 0Xl 2- B
DAM PSLB10Xl 2- B
DAMPSLS10X14-B

BOTTOM MOUNT 10X12
SIDE MOUNT 10X14

DAMPSLB10X14-B

BOTTOM MOUNT 10X14

9 13/16

13 7/8

DAMPSLS10X16-B

SIDE MOUNT 10X16

15 7/8

9 13/16

DAMPSLB10X16-B

BOTTOM MOUNT 10X16

9 13/16

15 7/8

DAMPSLS10X18-B
DAMPSLB10X18-B

SIDE MOUNT 10X18
BOTTOM MOUNT 10X18

17 7/8
9 13/16

9 13/16
17 7/8
9 13/16

DAMPSLSl0X20-B

SIDE MOUNT 10X20

19 7/8

DAMPSLB10X20-B

BOTTOM MOUNT 10X20

9 13/16

19 7/8

DAMPSLS10X22-B
DAMPSLB1OX22-B

SIDE MOUNT 10X22

21 7/8
9 13/16

9 13/16
21 7/8

23 7/8

9 13/16

DAMPSLSl

BOTTOM MOUNT 10X22
SIDE MOUNT 10X24

0X24-B

DAM PSLB10X24-

B

DAM PSLS12Xl 2- B
DAMPSLB12X12-B
DAM PSLSl 2X14- B
DAMPSLB12X14-B

BOTTOM MOUNT 10X24

9 13/16

23 7/8

SIDE MOUNT 12X12

11 7/8

11 13/16

BOTTOM MOUNT 12X12

11 13/16

11 7/8

SIDE MOUNT 12X14

13 7/8
11 13/16

11 13/16
13 7/8

15 7/8

11 13/16

DAM PSLSl 2X16- B

BOTTOM MOUNT 12X14
SIDE MOUNT 12X16

DAM PSLB12X16-

BOTTOM MOUNT 12X16

11 13/16

15 7/8

SIDE MOUNT 12X18

17 7/8

11 13/16

DAMPSLB12X18-B
DAM PSLS12X20-B

BOTTOM MOUNT 12X18
SIDE MOUNT 12X20

11 13/16
19 7/8

77/8
11 13/16

DAMPSLB12X20-B

BOTTOM MOUNT 12X20

11 13/16

19 7/8

DAMPSLS14X14-B

SIDE MOUNT 14X14

13 7/8

13 13/16

DAMPSLB14X14-B

BOTTOM MOUNT 14X14

13 13/16

13 7/8

DAMPSLS14X16-B
DAMPSLB14X16-B

SIDE MOUNT 14X16

15 7/8
13 13/16

13 13/16
15 7/8

19 7/8

13 13/16

B

DAM PSLSl 2X18- B

DAMPSLS14X20-B

BOTTOM MOUNT 14X16
SIDE MOUNT 14X20

DAMPSLB14X20-B

BOTTOM MOUNT 14X20

13 13/16

19 7/8

DAMPSLS16X16-B

SIDE MOUNT 16X16

15 7/8

15 13/16

DAMPSLB16X16-B
DAMPSLB16X20-B

BOTTOM MOUNT 16X16
BOTTOM MOUNT 16X20

15 13/16
19 7/8

15 7/8
15 13/16

SIDE
RAIL

RAILS
USING
_'

SIDE
RAIL

\_\

1 4

IN. SHEET
METAL
SCREWS

A95184

Fig. 3 - Securing Damper to Air Duct

MOUNTING

HUB

HUB

!/8"-_
GAP

ACTUATOR
HOUSING

OPEN

C

LOSEO

££
LU

/

Z
<
a

PLASTIC COVER

QUICK
RELEASE
BUTTON

1/8"-_
GAP

k--

ANTI-ROTATION
MOUNTING SCREW

CLS) CLOSED
(C_M) COMMON
(OPN) OPEN

_

ANTI-ROTATION
MOUNTING

SCREW (5/16")
A05250

Fig. 4 - Actuator Detail

Copyright
2005
CAC/BDP
• 7310
W.Morris
St.* Indianapolis,
Manufacturer

reserves

iN 46231

the right to change_ at any time_ specifications

Printed
and designs

in USA.

without

notice

Edition
and without

6

Date: 11/05

obligations,

Catalog
Rep{aces:

No: IM-DAMP-18
IM-DAMP-15

-

Pilot
Source Exif Data: 
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 6
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Fri Apr 20 13:46:20 2007
Author                          : 
Title                           : 
Subject                         :
EXIF Metadata provided by EXIF.tools

Navigation menu