CARRIER Controls And HVAC Accessories Manual L0912362
User Manual: CARRIER CARRIER Controls and HVAC Accessories Manual CARRIER Controls and HVAC Accessories Owner's Manual, CARRIER Controls and HVAC Accessories installation guides
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
INSTALLATION INSTRUCTIONS FOR CPADCURB001A00 PACKAGE Adaptor Kit USAGE CPRFCU RB006A00 or CPRFCU RB007A00 CPADCURB001A00 PACKAGE DESCRIPTION Failure to follow this caution may result in property damage. To prevent iniuries and rain damage, do not leave roof opening uncovered. If installation is not completed inm_ediatety after roof opening is cut and framed, provide an adequate temporary cover for the roof opening. CONTENTS QTY Installation Instructions 1 End 2 Side 2 Cross Support 1 Short Support 2 #10 Screws 1/2" (13mm)long 24 Gasketing PROPERTY DAMAGE HAZARD Use with existing curb GENERAL These adaptor kits are designed to allow SPP units with base rails to sit on existing, old style CPRFCURB006A00 or CPRFCURB007A00 curbs. This kit is for the small cabinet SPP units. INSTRUCTIONS 1. 1 1/2" (38mm) x 114" (6mm) 1" (25mm) x 314" (19mm) SAFETY CONSIDERATIONS Installation and se_wicing of air-conditioning equipment can be hazardous due to system pressure and electrical components. Only trained and qualified service personnel should install, repair, or smwice air-conditioning equipment. Untrained personnel can perform the basic maintenance functions of replacing filters. All other operations should be performed by trained service personnel. When working on air-conditioning equipment, obsmwe precautions in the literature, tags and labels attached to the unit, and other safety precautions that may apply. Recognize safety information. This is the safety--alert symbol _ When you see this symbol on the unit and in instructions or manuals, be alert to the potential for personal injury. Understand these signal words; DANGER, WARNING, and CAUTION. These words are used with the safety--alert symbol. DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies hazards which could result in personal injury or death. CAUTION is used to identify unsafe practices which may result in minor personal injury or product and property damage. NOTE is used to highlight suggestions which will result in enhanced installation, reliability, or operation. CUT HAZARD Failure to follow this caution may result in personal iniury. When removing access panels or performing maintenance functions inside your unit, be aware of sharp sheet metal parts and screws. Although special care is taken to reduce sharp edges to a minimum, be extremely careful when handling parts or reaching into the unit. 2. 3. Install the CPRFCURB006A00 or CPRFCURB007A00 curb per instructions provided with curb. If this is a retrofit applications, make sure the existing CPRFCURB006A00 or CPRFCURB007A00 dimensions match those in Fig. 4. If they don't match, then exiting curb is not as expected and adaptor kit may not fit as designed. Assemble adaptor kit as shown in Fig. 1, using provided screws. Caulk all (4) comers of adaptor so they are watertight. End Return Support X Side Screws Fig. 1 - Roofcurb Supply Support Adaptor 45 15/16" (1167) 23/16"===_(56) 15/8"-(41) --T 16" (406[ _' 21(548) 9/16" ------------_- |_'_ (254) ! R/A OPENING 2 3/16" (56) (_ 5_)--41 S/A OPENING *Measurements in 0 are in mm 303/8"J_ (772) Fig. 2 - Top View 1 1/2" (38) x 1/4" (6) Gasketing 4. Remove old gasket material fiom top perimeter of existing curb. 5. Caulk top surface of exiting curb - perimeter and duct openings - to provide seal between curb and adaptor. 6. If this is a retrofit applications the duct will already be installed in exiting curb. Set adaptor on top of curb opening duct openings correctly, as shown. For new installations, adaptor can be set on top of curb and duct dropped through and hang from top of adaptor. 1" (25) x 3/4" (19) Gasketing SPP Unit t CPADCURB001A00 Adaptor Kit Sheet Metal ,_ BaseRait ' Duct Extension_ Screw ' ] I_ Screw / CPRFCURB006A00 or CPRFCURB007A00 Curb 7/8" Typ. Fig. 3 - Roofcurb Adaptor Detail 7. 8. Screw inside flange of adaptor to existing curb, see Fig. 3. Install the 1 1/2" (38mm) x 1/4" (6mm) gasketing around the top perimeter of the adaptor kit - all 4 sides, see Fig. 3. 9. Install the 1" (25mm) x 3/4" (19mm) thick gasketing around all 4 sides of the return and supply duct openings. See Fig. 3. 10. Set HVAC unit with sheet metal base rail on top of adaptor. 11. To secure unit to roofcurb, screw through bottom flange of curb into steel base rail, Fig. 3. Deck Pan Fig. 4 -Adaptor Copyright on Existing 2009 CAC / BDP o 7310 Morris St. e Indianapolis, Manufacturer reserves the right to change, Curb IN 46231 at any time, specifications Printed and designs without in U.S.A notice and without obligations. Edition Date: 8/09 Catalog Replaces: No: IIK-CPADCURB-Ol New 8892-1P
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 2 Page Layout : SinglePage Page Mode : UseNone Producer : Goby Monitor Application version 4, 0, 0, 13 Create Date : Fri Feb 12 04:11:28 2010 Author : Title : Subject :EXIF Metadata provided by EXIF.tools