CDVI WIRELESS S P A GDR RECEIVER - GDR User Manual IS GDRUAUK
CDVI WIRELESS S.P.A. RECEIVER - GDR IS GDRUAUK
Users Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 963367 |
| Application ID | KbyTK46udfhI/N1q4+a2xw== |
| Document Description | Users Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 11.17kB (139637 bits) |
| Date Submitted | 2008-07-01 00:00:00 |
| Date Available | 2008-07-01 00:00:00 |
| Creation Date | 2008-06-27 15:16:31 |
| Producing Software | Corel PDF Engine Version 10.427 |
| Document Lastmod | 2008-06-27 15:16:31 |
| Document Title | IS-GDRUAUK.cdr |
| Document Creator | CorelDRAW Versione 10.0 |
| Document Author: | Gian Massimo Dalle Carbonare |
SENTRY GARAGE DOOR RECEIVER Use and installation manual 3 - WIRINGS Antenna Relay NO Output Power supply Made in Italy #030209 Thank you for choosing this product . You are recommended to read this manual carefully before installing this product. 1 - INTRODUCTION The Sentry Garage Door Receiver ( #030209) is single conversion superheterodyne receiver oeperating at 433,92 MHz in AM/ASK modulation. It is designed for automatic closing systems and anti-burglar systems. The antenna is direct connected with 6,5” wire . The relay K1 available output is only with NO type contact The operating mode of K1 is Pulse and or Latch ( see below for its configuration). The power supply is 9 Vdc provided by its own 9 Vdc / 300 mA external power supply. The IP grade of 2X allows only indoor installations. The product fully complies with the EMC European Regulations (CE) and the FCC Part 15 Regulations. 2 - TECHNICAL SPECIFICATIONS Receiver type Carrier Frequency Local oscillation frequency Demodulation Local oscillator type Channel width Intermediate frequency Input sensitivity Spurious emissions Input load Operating voltage Max power on relay contacts Relay number Operating modes Max activation delay Memory Security protocol Code combinations Operating temperature Enclosure IP grade Dimensions ( main box) Superheterodyne 433.92 MHz 6.6128 MHz AM/ASK VCO / PLL > 25 KHz 10.7 MHz -115 dBm < -57 dBm 50 Ohm 9 Vdc 24 VA Pulse / Latch 300 mS 100 TX Fixed Code 39 -4°/+158°F IP2X 1.57 x 0.9 x 2.2 in 4 - OPERATING MODES The operating mode can be Pulse or Latch according the following diagram. LD STEADY ON : PULSE Mode LD BLINKING : LATCH Mode LD gives the operating mode. To display the current operating mode push P1 for 4 sec 5 - OPERATING MODE SETTING Procedure 1) Press and hold the push-button P1 for 4 sec. until the green led LD comes ON ( Fig. 3); the led display the current operating mode according to par. 4. To modify push again P1 and release it within 1 sec.: once released P1: · from steady ON it will begin to blink ( Latch mode ); · from blinking it will come steady ON ( Pulse mode ). 1s LD P1 4s P1 LD P1 1s LD P1 LD Fig. 3 4 - PROGRAMMING MEMORIZZAZIONE TRANSMITTER DEI TRASMETTITORI AND RECEIVER Procedure 1) Press and hold the push-button P1 for 4 sec. until the green led LD comes ON ( Fig. 4); the led display the current operating mode according to par. 4. 2) Press the transmitter button down : LD switches OFF and ON again, waiting for another tx to memorize; 3) If within 10 sec. no more transmitters are activated, LD switches OFF and the procedure is over. TX End 10 Sec. 4s P1 P1 LD LD LD Fig. 4 7 - MEMORY FULL If the memory is full when you try to memorize one more transmitter LD flashes 3 times and the procedure ends. DEI TRASMETTITORI 8 - MEMORIZZAZIONE ERASING TRANSMITTERS FROM THE MEMORY TX Blinks: Latch Steady ON: Pulse 2 slow flashes Fast blinking 10 Sec. Fast blinking P1 4s P1 LD End LD 4s LD 3 slow flashes LD P1 4s LD LD End LD Fig. 5 Procedure 1) Press and hold the push-button P1 for 4 sec. until the green led LD comes ON ( Fig. 5); the led display the current operating mode according to par. 4. 2) Press and hold P1 for more 4 sec. : LD begins to blink fast. At this point you can do 2 different operations: A ) DELETE THE SINGLE TRANSMITTER Press the button down of the transmitter to delete. LD flashes twice slow and then begins again to blink fast for more tx to delete. If within 10 sec. no more transmitters are activated, LD switches OFF and the procedure is over. B ) ERASE ALL THE MEMORY Press and hold P1 for more 4 sec. : LD makes 3 slow flashes then switches off and the procedure ends. WARRANTY USAutomatic, LTD warrants this product to be free of defects in materials and workmanship for 2 YEAR. For a period of 2 YEAR following purchase USAutomatic, LTD. will repair or replace the product free of charge, including parts, shop labor and return shipping and handling. This 2 YEAR warranty does not cover the plastic case from normal wear or damage due to misuse of the receiver or transformer. Modifications to the supplied transformer will void the warranty. To have the product sent for warranty consideration, it must be returned with the proof of purchase and a return authorization number. To obtain a return authorization number please visit www.sentrygateopener.com or call 1-888711-0001 for assistance. This device complies with Part. 15 of the FCC Rules . Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. FCC ID : PWJGDR The return authorization number must be clearly marked on the outside of the return package or it may not be accepted. IS-GDRUAUK Rev. 3 del 10/06/2008 USAutomatic LTD 118 Hillside Drive Lewisville, TX 75057 1-866-711-0001 www.sentrygateopener.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.3 Linearized : No Page Count : 2 Create Date : 2008:06:27 15:16:31 Modify Date : 2008:06:27 15:16:31 Producer : Corel PDF Engine Version 10.427 Author : Gian Massimo Dalle Carbonare Creator : CorelDRAW Versione 10.0 Title : IS-GDRUAUK.cdrEXIF Metadata provided by EXIF.tools