Cambium Networks 89FT0023 cnPilot Outdoor E500 User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3001140
Application ID	M019Roahc0ZuRICa64EzZg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	94.7kB (1183766 bits)
Date Submitted	2016-05-23 00:00:00
Date Available	2016-06-15 00:00:00
Creation Date	2017-12-06 09:31:07
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-12-06 09:31:07
Document Title	Users Manual
Document Creator	Adobe Illustrator CC 2015 (Windows)

Quick Start Guide
Introduction
Step 1 (Pole Mount)
Step 2 (Pole Mount)
This sheet details assembly and
installation of cnPilot E500.
Package Contents
- E500 access point - x1
- E500 pole/wall mount bracket - x1
- 56V/30W gigabit passive PoE
power injector - x1
- Wall-mounting screw kit - x1
- RJ45 IP67 gland connectors - x2
- AC power cord (not for RoW SKU) - x1
cnPilot™ E500
Tools Required
All E500 Models
- Phillips screwdriver (Wall mount)
- Flat-head screwdriver (Pole mount)
Step 3 (Pole Mount)
Wall Mount (No Bracket)
Attach the cnPilot E500 to the mounting
bracket.
Insert the mounting straps through the
mounting bracket.
Step 1
(Wall Mount w/bracket)
Insert the wall anchors into the wall using
Insert the wall anchors into the wall using
the mounting bracket as a template and
the mounting bracket as a template and
insert the screws. Attach the cnPilot E500 to insert the screws.
the screws.
Tighten the mounting straps around the
pole using a flat-head screwdriver.
Step 2 (Wall Mount w/bracket)
Attach the mounting bracket to the screws.
Turn sheet over to continue.
Step 3
(Wall Mount w/bracket)
Reset Procedure
RoHS Compliance
WEEE Statement
Cambium Networks is committed to meeting the
requirements of the European Union (EU) Waste Electrical and Electronic Equipment (WEEE) Directive. This
Directive requires producers of electrical and electronic
equipment to finance the takeback, for reuse or recycling, of their products placed on the EU market after
August 13, 2005. Cambium Networks products that are
within the scope of the Directive are labelled with a
crossed-out "wheelie-bin" symbol, as required by the
Directive. It indicates that the product was placed on the
market after August 13, 2005 and that end users should
segregate the product from other waste at end-of- life.
Attach the cnPilot E500 to the mounting
bracket.
Powering
Eth1
Eth2
LEDs
System LED
Network LED
To power cnPilot E500:
- Connect the provided 56V/30W gigabit
passive PoE power injector provided to the
Eth1 port.
To power another device
using cnPilot E500:
- Connect the device to the Eth2 port .
- Configure cnPilot E500 to output power
on the Eth2 port by using the webpage
management interface.
The WEEE Directive is being implemented in each of the
27 EU countries through national legislation. Norway
and Switzerland have also implemented similar pieces of
legislation. As a result, the detailed requirements vary
considerably throughout the EU, and the Cambium
Networks WEEE compliance approach varies among
countries. In each country affected by the WEEE
legislation.
To reset cnPilot E500:
- Press the reset button. The cnPilot E500 will
reboot.
- Hold the button for 10 seconds. The cnPilot
E500 configuration will be reset to factory
default settings.
Default Configuration
cambiumnetworks.com/support
Default IP address:
- Received via DHCP.
- cnPilot E500 will use a default static IP
address of 192.168.0.1 if there is no DHCP
server.
Default login information:
- Username: admin
- Password: admin
System LED
Management protocols enabled by default:
When amber the system is powering up,
- HTTP, HTTPS (webpage management
and when green the system is fully powered. interface access), SSH (CLI management
Network LED
interface access).
When amber, the cnPilot E500 is not connected to cnMaestro, and when green,
cnPilot E500 is connected to cnMaestro.
Join the conversation
community.cambiumnetworks.com
™
cnMaestro
Ready
cnPilot E500 is cnMaestro ready
FCC Statement:
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20 cm between the radiator & your body.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Create Date                     : 2016:03:31 12:20:42-05:00
Creator                         : Adobe Illustrator CC 2015 (Windows)
Modify Date                     : 2016:05:18 14:39:10+08:00
Title                           : 
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Metadata Date                   : 2016:05:18 14:39:10+08:00
Creator Tool                    : Adobe Illustrator CC 2015 (Windows)
Format                          : application/pdf
Document ID                     : uuid:d3714e1d-68c8-4e3a-8490-de847e170368
Instance ID                     : uuid:ec9e7b5d-e1b6-4f6f-a931-7cfe73045eed
Producer                        : Adobe PDF library 15.00
Page Count                      : 3

EXIF Metadata provided by EXIF.tools