Carnegie Robotics 00067 Module - Platform User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	3513976
Application ID	Py716YO7oPR2qUGsUt7Xew==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	8.88kB (111025 bits)
Date Submitted	2017-08-16 00:00:00
Date Available	2017-08-16 00:00:00
Creation Date	2017-08-08 12:46:13
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2017-08-08 12:46:15
Document Title	Manual
Document Creator	Acrobat PDFMaker 11 for Word
Document Author:	Jim McCarty

Replace Platform Box
NOTE
Platform Box and mounting plate come as one unit. Do not try to remove
Platform Box from mounting plate.
All cable ends are unique and will fit only one way, except for the two power cables (2
and 4, Figure 4B2). These have the same ends and are interchangeable. If reversed, the
Laser Scanner or the Compute Box will not receive power and will not work.
Platform Box is approved for this application by the Federal Communications
Commission (FCC). FCC ID: 2AMDR00067. This device complies with part 15 of the
FCC rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications to this device, not expressly approved by the party responsible
for compliance, could void the user's authority to operate the equipment.
REMOVAL
1. Park A50 on a level floor.
2. Power off the A50.
a. Press I/O switch (1, Figure 4B1) on the Control Panel. Control Panel lights will turn off.
Brakes will apply automatically.
b. Raise the hood.
c. Raise the rear well cover to expose batteries.
d. Disconnect the main battery power supply. This removes all power to the system.
e. Lower rear well cover.
Figure 4B1. ON/OFF Switch on Control Panel
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
Confirm that blue LED (8, Figure 4B2) is not lit. This confirms that power to the Platform Box is off.
Disconnect Laser Scanner Ethernet cable (5, Figure 4B2).
Disconnect Compute Box Ethernet cable (4, Figure 4B2).
Disconnect RID Antenna cable (3, Figure 4B2).
Disconnect Compute Box power cable (2, Figure 4B2) (PN 56104677).
Disconnect Laser Scanner power cable (1, Figure 4B2) (PN ??? Nilfisk).
Disconnect Proximity Sensor harness (11, Figure 4B2). (PN 56104791).
Disconnect 23 pin harness (10, Figure 4B2) (PN ??? Nilfisk).
Remove four screws (9s, Figure 4B2) holding Platform Box and mounting plate to A50.
Lift Platform Box (6, Figure 4B2) with mounting plate (7, Figure 4B2) from the machine.
Return Platform Box to manufacturer for repair.
Figure 4B2. Platform Box
INSTALLATION
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
Position Platform Box (6, Figure 4B2) with mounting plate (7, Figure 4B2) for mounting.
Install four screws) (9, Figure 4B2) holding Platform Box and mounting plate to A50.
Connect 23 pin harness (10, Figure 4B2) (PN ??? Nilfisk) to Platform Box.
Connect Proximity Sensor harness (11, Figure 4B2) (PN 561047891) to Platform Box.
Connect Laser Scanner power cable (1, Figure 4B2) (PN ??? Nilfisk) to Platform Box.
Connect Compute Box power cable (2, Figure 4B2) (PN 56104677) to Platform Box.
Connect RID Antenna cable (3, Figure 4B2) to Platform Box.
Connect Compute Box Ethernet cable (4, Figure 4B2) (PN 56104678) to Platform Box.
Connect Laser Scanner Ethernet cable (5, Figure 4B2) (PN ??? Nilfisk) to Platform Box.
Connect the main power supply.
Power on the A50.
a. Raise the rear well cover.
b. Connect the main battery power supply. This restores power to the system.
c. Lower rear well cover.
d. Lower the hood.
e. Press 1/O switch (1, Figure 4A1) on the Control panel until Control Panel lights turn on.
This powers the control system. Brakes will release automatically.
25. Power on the A50. Press “I/O” toggle switch on the Control Panel (1, Figure 4A1). Control panel lights
should come on.
26. Raise the hood.
27. Check that blue LED on Platform Box (8, Figure 4B2) is lit. This means the Platform Box is getting
power.
28. Lower and the latch hood.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Jim McCarty
Create Date                     : 2017:08:08 12:46:13-04:00
Modify Date                     : 2017:08:08 12:46:15-04:00
Subject                         : 
Language                        : EN-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Metadata Date                   : 2017:08:08 12:46:15-04:00
Creator Tool                    : Acrobat PDFMaker 11 for Word
Document ID                     : uuid:b797b4fa-01b3-43bc-9519-a3ace6be09e8
Instance ID                     : uuid:6f4e7494-5160-46b4-aa75-7ced1fee7fca
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : Jim McCarty
Producer                        : Adobe PDF Library 11.0
Keywords                        : 
Source Modified                 : D:20170808164558
Company                         : 
Comments                        : 
Page Layout                     : OneColumn
Page Count                      : 3

EXIF Metadata provided by EXIF.tools