Carnegie Robotics 00079 Remote Identification Device User Manual Manual

Download:
Mirror Download [FCC.gov]
Document ID	3513857
Application ID	Oh3vzSyJ5TZXH81Cc05QqA==
Document Description	Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	25.56kB (319530 bits)
Date Submitted	2017-08-16 00:00:00
Date Available	2017-08-16 00:00:00
Creation Date	2017-08-08 12:50:35
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2017-08-08 12:50:37
Document Title	Manual
Document Creator	Acrobat PDFMaker 11 for Word
Document Author:	Jim McCarty

Replace Remote Interface Device (RID) Battery
NOTE
Remote Interface Device (RID) is approved for this application by the Federal
Communications Commission (FCC). FCC ID: 2AMDR00079. This device complies with
part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications to this device, not expressly approved by the party responsible
for compliance, could void the user's authority to operate the equipment
Expected battery life is 6 to 8 months, assuming normal usage. More frequent
operation will shorten battery life.
Medium to large tweezers, or a small blade screwdriver, and a Panasonic
CR2430 battery (or equivalent) are needed to perform this procedure.
REMOVAL
1. Begin to slide cover (3, Figure 4G1) from Remote Interface Device (RID) (1, Figure
4G1) to expose battery cover (2, Figure 4G1).
Figure 4G1. Removing Interface Device Cover
2. Remove RID (1, Figure 4G2) from cover (2, Figure 4G2).
Figure 4G2. RID Removed From Cover
3. Insert tip of medium tweezers (2, Figure 4G3) between battery cover (1, Figure 4G3)
and RID body (3, Figure 4G3), and begin to pry battery cover from RID body.
Figure 4G3. Prying Battery Cover From RID Body
4. Fully raise the battery cover (1, Figure 4G4) from the RID Body (2, Figure 4G4).
Figure 4G4. RID Battery Cover Raised From Body
5. Remove battery cover (2, Figure 4G5) from RID body (1, Figure 4G5).
Figure 4G5. RID Cover Removed
6. Using tip of medium tweezers (1, Figure 4G6), blade screwdriver, or finger nail,
carefully begin to slide battery (2, Figure 4G6) out of the RID (3, Figure 4G6).
Figure 4G6. Removing RID Battery
7. Grasp battery (1, Figure 4G7) with fingers when loose, then pull it from the RID (2,
Figure 4G7). Discard old battery according to local requirements.
Figure 4G7. RID Final Battery Removal
INSTALLATION
NOTE
Panasonic CR2430 battery (or equivalent) must be installed with the
correct polarity or the RID will not work. If installed with reverse polarity,
the battery and RID will not be damaged. The remote simply will not work.
8. Check polarity of battery (1, Figure 4G8) before insertion. Positive pole is marked with a “+” (plus)
on the side with printing (2, Figure 4G8).
Figure 4G8. Checking RID Battery Polarity
9. Slide new battery (2, Figure 4G9) into the RID (1, Figure 4G9). Push until firmly seated.
Figure 4G9. RID Battery Installed
10. Insert lip at rear of battery cover (1, Figure 4G10) into RID (2, Figure 4G10).
Figure 4G10. Replacing Battery Cover
11. Lower battery cover (1, Figure 4G11) and press down to lock it. You should hear a “click”.
Figure 4G11. Battery Cover Closed
12. Insert assembled RID (1, Figure 4G12) into cover (2, Figure 4G12).
Figure 4G12. Inserting RID Into Cover
13. Wrap cover fully around RID (1, Figure 4G13).
Figure 4G13. RID Assembled

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : Jim McCarty
Create Date                     : 2017:08:08 12:50:35-04:00
Modify Date                     : 2017:08:08 12:50:37-04:00
Subject                         : 
Language                        : EN-US
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Metadata Date                   : 2017:08:08 12:50:37-04:00
Creator Tool                    : Acrobat PDFMaker 11 for Word
Document ID                     : uuid:01b6a406-dd00-4563-8f37-b8fd785221ff
Instance ID                     : uuid:913f2ac5-0554-4d86-8a08-c0bb70ca3c1e
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : Jim McCarty
Producer                        : Adobe PDF Library 11.0
Keywords                        : 
Source Modified                 : D:20170808164938
Company                         : 
Comments                        : 
Page Layout                     : OneColumn
Page Count                      : 7

EXIF Metadata provided by EXIF.tools