Casambi Technologies CBUTED Bluetooth controllable trailing-edge dimmer User Manual

Casambi Technologies Oy Bluetooth controllable trailing-edge dimmer

User Manual

DescriptionCBU-TED is a Bluetooth controllable trailing-edge dimmer for phase control of incandescent lamps, dimmable LED lamps and dimmable LED control gear. It is to be connected between the incoming line voltage and the light source. Maximum allowable ambient temperature must be taken into concideration when selecting the mounting location.CBU-TED is able to control up to 75 W at 120 VAC.As a part of Casambi network, CBU-TED can be used to control lights based on multiple con-trol strategies including preset scenes, automatic schedules and daylight responsive dimming.CBU-TED can be congured and controlled with Casambi app, available for iOS and Android devices, as well as with traditional wall switches.Technical dataLighting control for the Modern WorldWiring diagramDimming without AppDimensionsCBU-TED USA & CanadaBluetooth controllable trailing-edge dimmer www.casambi.comLNSolid and stranded:16-18 AWG/1-1,5 mm2Strip length: 6-8 mmWire info:120 VAC60 Hz1. Turn lights on from a wall switch. 2. Quickly ick the wall switch o (max. 1 sec.) and back on. The light level starts to increase gradually. 3. Flick the switch again at desired dim level. The selected level is saved automatically. 4. If the second ick is not done within 8 sec. the light intensity reaches its maximum level. 5. Flicking the switch can also be used to switch between predened scenes.ON OFF/ON(<1 sec.)OFF/ON(<1 sec.)8 sec.from 1stOFF/ONtimeType of loadIncandescent and high voltage halogens (R)High quality dimmable LED and CFL bulbs (C) 1)Trailing edge dimmable LED drivers (C) 1)High voltage AC LED modules (R) 2)Max. load75 W75 W75 W75 WNever connect inductive loads, such as iron core transformers. This could cause permanent damage to the dimmer. Do not mix dierent types of loads.Wire wound transformers, electric motors and other inductive loads (I) Not allowedNon-dimmable uorescent lamps, LED and CFL bulbs (C) Not allowedLow voltage halogens with electronic transformers (C) 1) 75 W1) Dimming quality depends solely on the load electronics. Do not mix dierent types of bulbs or loads.2) Some LED modules may icker at low dimming levels.InputVoltage: 120 VACFrequency: 60 HzMax. mains current: 0,65 ANo-load standby power: < 0,3 WOutputDimming method: trailing-edge phase controlMax. output power: 75 W @ 120 VACMax. output current: 0,65 AMin. load requirement: 1 WMax. inrush current: 10 A, 100 msRadio transceiverOperating frequencies: 2,4...2,483 GhzMaximum output power: +4 dBmOperating conditionsAmbient temperature, ta: -4°F to 113°F (-20 to +45°C)Max. case temperature, tc: 167°F (+75°C)Location of tc point: bottom side, underneath output connectorStorage temperature: -13°F to 122°F (-25...+50°C)Max. relative humidity: 0...80%, non-cond. ConnectorsWire range, solid & stranded: 16-18 AWG 1-1,5 mm2Wire strip length: .25” (6-8 mm)Mechanical dataDimensions: 1.60 x 1.45 x 0.55 inch 40,4 x 36,3 x 14,0 mmWeight: 0.5 oz (15 g)Degree of protection: IP20 (indoor use only)FCC ID: 2ALA3-CBUTEDIC: 22496-CBUTEDUL: UL Listed, E494741Tc** Tc point is on bottom side40,436,318,1520,212.7 14.0Dimensions are in mm.Trailing edge dimmerCBU-TEDL N NMax.0.65 A
InstallationMake sure that the mains voltage is switched o before making any connections. Use 16-18 AWG solid or stranded conductor electrical wires. Strip the wire 6-8 mm from the end.Press the buttons on top of the dimmer case and insert the wires to the corresponding holes. Make sure to connect the input and output correctly. Input connector is marked with letters L and N, while the output connector is marked with letter N and a symbol with a wave and an arrow ( ).If you install the dimmer into a heat sensitive environment (e.g. inside a luminaire or in a ceiling outlet box above a luminaire), make sure that the ambient temperature does not exceed the specied maximum value. Using the dimmer in a heat sensitive environment may limit the maximum output power.CBU-TED, as any other Casambi product, should not be placed in a metal enclosure, such as metal junction boxes. Metal will attenuate radio signals which are crucial to the operation of the product. If the product will have to installed into a junction box, make sure to use a plastic junction box.RangeThe range between two CBU-TEDs or between a CBU-TED and a smart phone can vary a lot depending on obstacles and surrounding material. In open air the range between two CBU-TEDs can be in excess of 200 ft, but if the unit is encapsulated into a metal structure, the range can be only few feet. Therefore, thorough testing is highly suggested.Casambi uses mesh network technology so each CBU-TED acts also as a repeater. When testing the network, it is important to test that each unit can be controlled from any point of the network covered area.Information in this document is subject to change.CBU-TED User Guide v1.0B USA and CanadaCopyright Casambi Technologies Oy 2018.Compliance StatementThis device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.WarningChanges or modications not expressly approved by Casambi Technologies Oy could void the user’s authority to operate the equipment.FCC Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Radiation Exposure Statement for CanadaThis device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:(1) This device may not cause interference(2) This device must accept any interference, including interference that may cause undesired operation of the device.This equipment is exempt from the routine RF exposure evaluation requirements of RSS-102. This equipment should be installed and operated with a minimum distance of 20 cm between the antenna and the user or bystanders.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:(1) l’appareil ne doit pas produire de brouillage;(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Ce matériel n’est pas sujet à l’évaluation habituelle d’exposition RF selon RSS102. Ce matériel devrait être installé et exploité en gardant une distance minimale de 20 cm entre l’antenne et l’utilisateur ou les spectateurs.Radiation Exposure Statement for FCCThis device complies with FCC radiation exposure limits for an uncontrolled environment. This device shall be installed and operated with a minimum distance of 0.8” (2cm) between users or bystanders and the device.Casambi Technologies OyBertel Jungin aukio 1 E, 02600 Espoo, Finland

Navigation menu