Casambi Technologies CBUTED Bluetooth controllable trailing-edge dimmer User Manual

Download:
Mirror Download [FCC.gov]
Document ID	4072828
Application ID	M5bUFYtvPyCxcjtZ858RMg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	16.13kB (201633 bits)
Date Submitted	2018-11-15 00:00:00
Date Available	2018-11-15 00:00:00
Creation Date	2018-10-26 17:19:49
Producing Software	Adobe PDF Library 10.0.1
Document Lastmod	2018-10-26 17:19:50
Document Title	User Manual
Document Creator	Adobe InDesign CS6 (Windows)

CBU-TED
USA & Canada
Bluetooth controllable trailing-edge dimmer
www.casambi.com
Description
CBU-TED is a Bluetooth controllable trailing-edge dimmer for phase control of incandescent
lamps, dimmable LED lamps and dimmable LED control gear. It is to be connected between
the incoming line voltage and the light source. Maximum allowable ambient temperature must
be taken into concideration when selecting the mounting location.
CBU-TED is able to control up to 75 W at 120 VAC.
As a part of Casambi network, CBU-TED can be used to control lights based on multiple control strategies including preset scenes, automatic schedules and daylight responsive dimming.
CBU-TED can be configured and controlled with Casambi app, available for iOS and Android
devices, as well as with traditional wall switches.
Wiring diagram
Technical data
Input
Voltage:				120 VAC
Frequency:				60 Hz
Max. mains current:			
0,65 A
No-load standby power:			
< 0,3 W
120 VAC
60 Hz
Max.
N 0.65 A N
CBU-TED
Trailing edge dimmer
Wire info:
Solid and stranded:
16-18 AWG/1-1,5 mm2
Strip length: 6-8 mm
1. Turn lights on from a wall switch.
2. Quickly flick the wall switch off (max.
1 sec.) and back on. The light level
starts to increase gradually.
3. Flick the switch again at desired dim
level. The selected level is saved
automatically.
5. Flicking the switch can also be
used to switch between predefined
scenes.
trailing-edge phase control
75 W @ 120 VAC
0,65 A
1W
10 A, 100 ms
Radio transceiver
Operating frequencies:			
Maximum output power:			
2,4...2,483 Ghz
+4 dBm
Operating conditions
Ambient temperature, ta:			
-4°F to 113°F (-20 to +45°C)
Max. case temperature, tc:		
167°F (+75°C)
Location of tc point:			
bottom side, underneath output
				connector
Storage temperature:			
-13°F to 122°F (-25...+50°C)
Max. relative humidity:			
0...80%, non-cond.
Dimming without App
4. If the second flick is not done within
8 sec. the light intensity reaches its
maximum level.
Output
Dimming method:			
Max. output power:			
Max. output current:			
Min. load requirement:			
Max. inrush current:			
time
ON
OFF/ON
(<1 sec.)
OFF/ON
(<1 sec.)
8 sec.
from 1st
OFF/ON
Connectors
Wire range, solid & stranded:		
16-18 AWG
				1-1,5 mm2
Wire strip length:			
.25” (6-8 mm)
Mechanical data
Dimensions:				
Weight:				
Degree of protection:			
1.60 x 1.45 x 0.55 inch
40,4 x 36,3 x 14,0 mm
0.5 oz (15 g)
IP20 (indoor use only)
FCC ID:				2ALA3-CBUTED
IC:				22496-CBUTED
UL:				UL Listed, E494741
Dimensions
40,4
36,3
Tc*
18,15
12.7 14.0
Type of load
Incandescent and high voltage halogens (R)
High quality dimmable LED and CFL bulbs (C) 1)
Trailing edge dimmable LED drivers (C) 1)
Low voltage halogens with electronic transformers (C) 1)
High voltage AC LED modules (R) 2)
Non-dimmable fluorescent lamps, LED and CFL bulbs (C)
Wire wound transformers, electric motors and other inductive loads (I)
Never connect inductive loads, such as iron core transformers. This could cause
permanent damage to the dimmer. Do not mix different types of loads.
20,2
* Tc point is on bottom side
Dimensions are in mm.
Max. load
75 W
75 W
75 W
75 W
75 W
Not allowed
Not allowed
1)
Dimming quality depends solely on the load electronics. Do not mix different types of bulbs or loads.
2)
Some LED modules may flicker at low dimming levels.
Lighting control for the Modern World
Installation
Make sure that the mains voltage is switched off before making any connections. Use 16-18 AWG solid or stranded conductor electrical wires. Strip the
wire 6-8 mm from the end.
Press the buttons on top of the dimmer case and insert the wires to the corresponding holes. Make sure to connect the input and output correctly. Input
connector is marked with letters L and N, while the output connector is marked with letter N and a symbol with a wave and an arrow ( ).
If you install the dimmer into a heat sensitive environment (e.g. inside a luminaire or in a ceiling outlet box above a luminaire), make sure that the ambient
temperature does not exceed the specified maximum value. Using the dimmer in a heat sensitive environment may limit the maximum output power.
CBU-TED, as any other Casambi product, should not be placed in a metal enclosure, such as metal junction boxes. Metal will attenuate radio signals which
are crucial to the operation of the product. If the product will have to installed into a junction box, make sure to use a plastic junction box.
Range
The range between two CBU-TEDs or between a CBU-TED and a smart phone can vary a lot depending on obstacles and surrounding material. In open
air the range between two CBU-TEDs can be in excess of 200 ft, but if the unit is encapsulated into a metal structure, the range can be only few feet.
Therefore, thorough testing is highly suggested.
Casambi uses mesh network technology so each CBU-TED acts also as a repeater. When testing the network, it is important to test that each unit can
be controlled from any point of the network covered area.
Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
Radiation Exposure Statement for FCC
This device complies with FCC radiation exposure limits for an uncontrolled environment. This device shall be installed and operated with a minimum
distance of 0.8” (2cm) between users or bystanders and the device.
Warning
Changes or modifications not expressly approved by Casambi Technologies Oy could void the user’s authority to operate the equipment.
FCC Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement for Canada
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions:
(1) This device may not cause interference
(2) This device must accept any interference, including interference that may cause undesired operation of the device.
This equipment is exempt from the routine RF exposure evaluation requirements of RSS-102. This equipment should be installed and operated with a
minimum distance of 20 cm between the antenna and the user or bystanders.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes:
(1) l’appareil ne doit pas produire de brouillage;
(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Ce matériel n’est pas sujet à l’évaluation habituelle d’exposition RF selon RSS102. Ce matériel devrait être installé et exploité en gardant une distance
minimale de 20 cm entre l’antenne et l’utilisateur ou les spectateurs.
Information in this document is subject to change.
CBU-TED User Guide v1.0B USA and Canada
Casambi Technologies Oy
Bertel Jungin aukio 1 E, 02600 Espoo, Finland
Copyright Casambi Technologies Oy 2018.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.3-c011 66.145661, 2012/02/06-14:56:27
Create Date                     : 2018:10:26 17:19:49+03:00
Metadata Date                   : 2018:10:26 17:19:50+03:00
Modify Date                     : 2018:10:26 17:19:50+03:00
Creator Tool                    : Adobe InDesign CS6 (Windows)
Instance ID                     : uuid:43418c61-a815-4592-9768-9b045786f936
Original Document ID            : xmp.did:30407E19B309E511B91ECECDB2672EC4
Document ID                     : xmp.id:6DD980282AD9E81191B1D0D73224D80B
Rendition Class                 : proof:pdf
Derived From Instance ID        : xmp.iid:6CD980282AD9E81191B1D0D73224D80B
Derived From Document ID        : xmp.did:E7C2AB3213D7E8118F67876933F1BB69
Derived From Original Document ID: xmp.did:30407E19B309E511B91ECECDB2672EC4
Derived From Rendition Class    : default
History Action                  : converted
History Parameters              : from application/x-indesign to application/pdf
History Software Agent          : Adobe InDesign CS6 (Windows)
History Changed                 : /
History When                    : 2018:10:26 17:19:49+03:00
Format                          : application/pdf
Producer                        : Adobe PDF Library 10.0.1
Trapped                         : False
Page Count                      : 2
Creator                         : Adobe InDesign CS6 (Windows)

EXIF Metadata provided by EXIF.tools