CastleNet Technology RTL8188CTV 802.11 b/g/n WLAN 1T1R Card User Manual RTL8188CTV FCC QIG v010

Download:
Mirror Download [FCC.gov]
Document ID	1783499
Application ID	vDAms62DX2t6FnIPLtCIhQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	53.62kB (670207 bits)
Date Submitted	2012-09-05 00:00:00
Date Available	2012-09-05 00:00:00
Creation Date	2012-09-03 16:41:19
Producing Software	Acrobat Distiller 8.1.0 (Windows)
Document Lastmod	2012-09-03 16:43:00
Document Title	Microsoft Word - RTL8188CTV_FCC_QIG_v010
Document Creator	PScript5.dll Version 5.2.2
Document Author:	EMILY

User Guide
RTL8188CTV
802.11 b/g/n WLAN 1T1R Card
Revision: 1.0
File name
Date
RT8188CTV_v010c
26‐Apr‐2012
1 of 17
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
‐
‐
‐
‐
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This transmitter must not be co‐located or operating in conjunction with any other antenna or
transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
2 of 17
This device is intended only for OEM integrators under the following conditions:
The antenna must be installed such that 20 cm is maintained between the antenna and users, and
The transmitter module may not be co‐located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end‐product for any additional compliance
requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop
configurations or co‐location with another transmitter), then the FCC authorization is no longer
considered valid and the FCC ID can not be used on the final product. In these circumstances, the
OEM integrator will be responsible for re‐evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must be
labeled in a visible area with the following: “Contains FCC ID: RK9‐RTL8188CTV”. The grantee's FCC
ID can be used only when all FCC compliance requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
3 of 17
Canada-Industry Canada (IC)
This device complies with RSS‐210 of the Industry Canada Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR‐210 d'Industrie Canada applicable aux appareils radio
exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne
doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu,
y compris un brouillage susceptible de provoquer un fonctionnement indésirable.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20
cm de distance entre la source de rayonnement et votre corps.
This device is intended only for OEM integrators under the following conditions: (For module device use)
1) The antenna must be installed such that 20 cm is maintained between the antenna and users,
and
2) The transmitter module may not be co‐located with any other transmitter or antenna.
As long as 2 conditions above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end‐product for any additional compliance
requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour
utilisation de dispositif module)
1) L'antenne doit être installée de telle sorte qu'une distance de 20 cm est respectée entre
l'antenne et les utilisateurs, et
2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 2 conditions ci‐dessus sont remplies, des essais supplémentaires sur l'émetteur ne
seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur son
produit final pour toutes exigences de conformité supplémentaires requis pour ce module installé.
4 of 17
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or
co‐location with another transmitter), then the Canada authorization is no longer considered valid
and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will
be responsible for re‐evaluating the end product (including the transmitter) and obtaining a
separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple pour certaines configurations
d'ordinateur portable ou de certaines co‐localisation avec un autre émetteur), l'autorisation du
Canada n'est plus considéré comme valide et l'ID IC ne peut pas être utilisé sur le produit final.
Dans ces circonstances, l'intégrateur OEM sera chargé de réévaluer le produit final (y compris
l'émetteur) et l'obtention d'une autorisation distincte au Canada.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be installed
such that 20 cm may be maintained between the antenna and users. The final end product must be
labeled in a visible area with the following: “Contains IC: 4729A‐RTL8188CTV”.
Plaque signalétique du produit final
Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l'antenne
peut être installée de telle sorte qu'une distance de 20cm peut être maintenue entre l'antenne et
les utilisateurs. Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante:
"Contient des IC: 4729A‐RTL8188CTV".
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to
install or remove this RF module in the user’s manual of the end product which integrates this
module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final quant à
la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final
qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
5 of 17
根據低功率電波輻射性電機管理辦法:
第十二條 經型式認證合格之低功率射頻電機，非經許可、公司、商號或使用者均不得擅自變
更頻率，加大功率或變更原設計之特性及功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信:經發現有干擾現象時，
應立即停用，並改善至無干擾時方得繼續使用。
前項合法通信，指依電信規定作業之無線電信。低功率射頻電機須忍受合法通信或工業、科
學及醫療用電波輻射性電機設備之干擾。
6 of 17
CONTENTS
1. INTRODUCTION ............................................................................................................................ 9
1.1 Scope .................................................................................................................................... 9
1.2 Features ................................................................................................................................ 9
1.3 Module Appearance (Main Model Type) ............................................................................. 10
1.4 Model Definition .................................................................................................................. 10
2. HARDWARE SPECIFICATION ..................................................................................................... 11
2.1.1 General Specification ............................................................................................... 11
2.1.2 Environmental .......................................................................................................... 12
2.1.3 PIN Define & Input Voltage....................................................................................... 13
2.1.4 Power Consumption ................................................................................................. 14
2.2 MECHANICAL SPECIFICATION ........................................................................................ 14
2.2.1 Board Dimension ...................................................................................................... 14
2.2.2 Mechanical Drawing (unit: mm) ................................................................................ 15
2.2.3 FFC specification (unit: mm) .................................................................................... 16
2.3 SOFTWARE SPECIFICATION............................................................................................ 16
2.3.1 Operating system & Supported CPU Plaform .......................................................... 16
3. PACKING & ACCESSORIES ........................................................................................................ 17
7 of 17
Revision History
Rev.
Change Note
Date
1.0
‐ First release
26‐Apr‐2012
Declaration
This document contains information is confidential. Any disclosure, copying, distribution, or action
taken in reliance on the contents of the information contained in this document is strictly prohibited.
8 of 17
1. INTRODUCTION
1.1 Scope
The RTL8188CTV Series is the WLAN 802.11n 1T1R module that offers various flexible model type for
main device design selection like it co‐layout with USB connector and Flex Flat Connector for USB host
interface communication with main board, the default RF antenna is PCB antenna but reserve IPEX
connector pin to satisfy your Wi‐Fi TX/RX performance design consideration with Wi‐Fi RF signal, the
default input voltage is 3.3V but allow 5V customization on other model type of RTL8188USB module
series . it is a suitable solution for IPC, Media Player, Set‐Top‐Box, IP‐CAM, Tablet with this WLAN 11n
USB module for wireless connectivity .
1.2 Features
General
Form factor:
Bus Interface: USB interface.
Connector Type:
PCB Dimension: 38mm x 17 mm x 1mm
RF Antenna:
Input Voltage: +3.3V (5V is optional) .
RoHS Compliant.
Mini‐Size.
USB 6 pin (Default) or Flex Flat Cable (FFC) , Optional.
PCB Antenna (default) , IPEX (optional) for Wi‐Fi data transmission.
WLAN Features
Complete 802.11n 1T1R (1x1) solution for 2.4GHz band
Backward compatible with 802.11b/g devices while operating at 802.11n data rates.
150Mbps PHY rate.
20MHz/40MHz bandwidth.
WEP 64/128, WPA, WPA2, TKIP, AES.
QoS‐WMM, WMM‐PS.
WPS PBC, PIN (Software ).
Supports 16 BSSIDs.
9 of 17
1.3 Module Appearance (Main Model Type)
RTL8188 CTV SC series
RTL8188CTV SH series
PCB
Antenna
PCB
Antenna
(Default)
USB 6 pin
Connector
IPEX connector
(Alternative)
(Default)
6 pin FFC
HotBar
Reflow
IPEX connector
(Alternative)
1.4 Model Definition
RTL8188USB series basically distinguish various model types that according to Main Chip, OS, USB
Connector type, RF Antenna, and input voltage, the model naming rule shown below:
10 of 17
z
Main Chip: RTL8188CTV
Model Type
Default Basic Model Type: RTL8188CTV‐SC3
OS
Connector
Antenna
Input Voltage
RTL8188CTV‐SH5
5V
FFC(6 pin)
RTL8188CTV‐SH3
3.3V
PCB x1
RTL8188CTV‐SC5
5V
USB 6 pin connector
RTL8188CTV‐SC3
3.3V
Linux / Android
RTL8188CTV‐SH5X
Only
5V
FFC(6 pin)
RTL8188CTV‐SH3X
3.3V
IPEX x 1
RTL8188CTV‐SC5X
5V
USB 6 pin connector
RTL8188CTV‐SC3X
3.3V
2. HARDWARE SPECIFICATION
2.1.1 General Specification
Specification
IEEE 802.11 b/g/n Wireless Local Area Networks
Security
WEP 64/128, WPA, WPA2, TKIP, AES.
PHY Rate
Max.150Mbps PHY Rate for both transmit and receiving
RF Frequency Range
2.412G~2.484GHz
Operating Voltage
+3.3V (Default) 5V (Selectable)
Interface
USB
Connector Type
USB Connector or Flex Flat Cable
WLAN RF
PCB antenna (Default)
(Selectable)
IPEX Connector (Optional)
11 of 17
2.1.2 Environmental
Operating
Operating temperature: 0 to 85 degree C
Relative Humidity : 5‐90% (non‐condensing)
Storage
Temperature: ‐20 to 85 degree C
Relative Humidity : 5‐95% (non‐condensing)
12 of 17
2.1.3 PIN Define & Input Voltage
PIN 6
PIN 6
PIN 1
PIN 1
INPUT VOLTAGE:
5V
3.3V
Notice:
Please decide which Input voltage of default 3.3V or 5V you will implement to your main board and
refer to model definition to choose the suitable model type you want on Chapter 1.4
PIN DEFINE:
Model
PIN#
RTL8188 USB module series
Definition
3.3V IN (Default) / 5V IN (Optional)
LED
High Speed USB D‐ signal
High Speed USB D+ signal
Radio On/Off
GND
Hi=On ; Low=Off
13 of 17
2.1.4 Power Consumption
Mode
Power consumption (mA) / 3.3V
(2.4GHz frequency band)
Activity Î
Uplink
Downlink
Radio off
Idle
Disable
11b mode
163/192mA
121/133mA
1.39mA
97.8mA
1.39mA
11g mode
154/195mA
121/125mA
1.39mA
97.8mA
1.39mA
11n mode(HT20)
160/206mA
117/123mA
1.39mA
98.5mA
1.39mA
11n mode(HT40)
183/215mA
123/128mA
1.39mA
101.18mA
1.39mA
2.2 MECHANICAL SPECIFICATION
2.2.1 Board Dimension
Form factor
Custom made mini‐size
PCB Dimension
38 mm*17 mm ( +/‐ 0.20mm)
PCB thickness
1.0mm (+/‐0.10mm)
SMD
Single side
Max. height of components
Top side
(from PCB)
3.0mm (USB connector model type)
2.0mm ( FFC with shielding case)
Bottom side
0mm
14 of 17
2.2.2 Mechanical Drawing (unit: mm)
RTL8188CTV‐SC Series
RTL8188CTV‐SH Series
15 of 17
2.2.3 FFC specification (unit: mm)
RTL8188CTV‐SH Series
2.3 SOFTWARE SPECIFICATION
2.3.1 Operating system & Supported CPU Plaform
Operating System
RTL8188CTV‐SC/SH Series
Windows XP
Windows 7
N/A
Linux (kernel 2.6.18 ~ 2.6.38)
Android 1.6 ~ 2.3.x
Yes
Supported CPU Platform:
PC‐Based X86 system
ARM
(Embedded System with ARM processor : TBD/TBC is needed )
MIPS
(Exclude Embedded System)
16 of 17
3. PACKING & ACCESSORIES
Contents
Unit
Remarks
RTL8188USB series
*1
Follow customer Labeling spec.
Cable
*0
No cable is necessary.
Carton
TBD
Per customer requirement
17 of 17

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 8.1.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2.2
Modify Date                     : 2012:09:03 16:43+08:00
Create Date                     : 2012:09:03 16:41:19+08:00
Metadata Date                   : 2012:09:03 16:43+08:00
Format                          : application/pdf
Title                           : Microsoft Word - RTL8188CTV_FCC_QIG_v010
Creator                         : EMILY
Document ID                     : uuid:64bf96fb-be68-4464-8ffd-f03ed3250391
Instance ID                     : uuid:1fa513f3-bfe3-464e-a080-9899d3fca954
Page Count                      : 17
Author                          : EMILY

EXIF Metadata provided by EXIF.tools