Chamberlain Group The 1255433 Remote control transmitter User Manual Instructions

Download:
Mirror Download [FCC.gov]
Document ID	5912
Application ID	uRyck0UkBUXWMY8lwpIZvw==
Document Description	Instructions
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	2.58kB (32292 bits)
Date Submitted	1998-08-21 00:00:00
Date Available	1998-10-05 00:00:00
Creation Date	1998-06-30 16:27:44
Producing Software	Acrobat Distiller 3.0 for Power Macintosh
Document Lastmod	0000-00-00 00:00:00
Document Title	Instructions

®
433MHz 3-Function Remote Control
OWNER’S MANUAL
To comply with FCC rules, adjustment or modifications of this receiver and/or
transmitter are prohibited, except for changing the code setting or replacing the
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
The Security✚ remote control (with blue push buttons)
works only with rolling code door openers and light
controls (with an orange SRT button and yellow indicator
light). The code between the remote control and the
receiver changes with each use, randomly accessing over
100 billion new codes.
Instructions are given below for programming your
opener to match the remote control's code. The
additional remote control buttons can also activate other
Security✚ garage door openers and/or light controls.
(Instructions for programming light products are
included with those accessories.)
SECURITY✚ GARAGE DOOR OPENERS
Program the Opener to Accept
the Remote Control Code
Select a remote control push button to operate the receiver.
The large button is recommended for use with the garage
door opener.
If you have a Premium Control Console:
1. With the door closed, press and hold the selected remote
push button. See Figure 1.
2. Press and hold the Light button on the door control, Figure
2.
3. Press and hold the door control push button.
4. After the opener light flashes, release all buttons.
If you do not have a Premium Control Console:
1. Press and hold the selected remote push button. See
Figure 1.
2. Press and release the SRT (learn) button on the opener
panel. See Figure 3. The indicator light on the panel will
begin to blink and the opener light will flash once.
3. Release the remote push button.
Now the opener will operate when that remote control button
is pressed. Test it by pressing the remote button to see that
the door goes up and down.
To Erase All Remote Control Codes
Press and hold the SRT button on the opener panel until the
indicator light turns off (about 6 seconds). All remote codes
are now erased. Then follow the steps above to re-program
each remote control.
To Control the Opener Light (Premium Consoles)
With Security✚ remote controls, a push button can be
programmed to operate the opener light without opening the
door.
1. With the door closed, press and hold the remote button
that you want to control the light.
2. Press and hold the Light button on the door control.
3. Press and hold the Lock button on the door control.
4. After the opener light flashes, release all buttons.
Test by pressing the remote push button. The opener light
should turn on or off but the door should not move.
114A2334
WARNING
Children operating or playing with a garage door
opener can injure themselves or others. The garage
door could close and cause serious injury or death.
Do not allow children to operate the door push
button(s) or remote control(s).
A moving garage door could injure or kill someone
under it. Activate the opener only when you can see
the door clearly, it is free of obstructions, and is
properly adjusted.
Figure 1
Figure 2
Door Control
Push button
Select a push button
to operate opener
PREMIUM
CONTROL CONSOLE
LIGHT
3-FUNCTION
REMOTE
CONTROL
Figure 3
Orange
SRT (learn)
Button
Yellow
Indicator
Light
LOCK
Light
Lock
SECURITY✚ GARAGE DOOR OPENER
Code programming
instructions are also
located on the opener
panel.
WARNING
Keep batteries away from small children. If
swallowed, promptly notify doctor.
The Remote Control Battery
The lithium battery should produce
power for up to 5 years. To replace
the battery, use the visor clip or
screwdriver blade to pry open the case, as
shown. (“Open” location is stamped on back of
case.) Insert battery positive side down. To replace
cover, insert the 3 tabs at the opposite end and snap shut.
Dispose of old battery properly.
Open this end
first to avoid
cracking
housing
Replacement Parts:
SECURITY✚ 3-Function remote control housing
only (no circuit board) – 41A5032; 3V 2032
Lithium Battery – 10A20; Visor Clip – 29B134.
FOR 433MHz
When ordering parts, always provide the following
information:
• Product Type
• Part Number
• Model Number
• Part Description
For the repair or replacement parts you need
Call 7 am – 7 pm, 7 days a week:
1-800-366-PART
(1-800-366-7278)
© 1998, Sears Roebuck & Company
All Rights Reserved
Printed in Mexico

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.1
Linearized                      : No
Page Count                      : 1
Create Date                     : 1998:06:30 16:27:44
Producer                        : Acrobat Distiller 3.0 for Power Macintosh

EXIF Metadata provided by EXIF.tools