Chamberlain Group The 1D1519 Garage Door Remote Control User Manual 114A2504 Clicker

Download:
Mirror Download [FCC.gov]
Document ID	276786
Application ID	y1IUq4q3BcJBv3BMXTzBLw==
Document Description	instructions
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	14.15kB (176885 bits)
Date Submitted	2002-10-15 00:00:00
Date Available	2002-11-12 00:00:00
Creation Date	2001-06-25 14:13:25
Producing Software	Acrobat Distiller 4.05 for Macintosh
Document Lastmod	2001-06-25 14:13:27
Document Title	114A2504 Clicker
Document Creator	QuarkXPressª: LaserWriter 8 8.7
Document Author:	Chamberlain Group

CLICKER
Model No. CLT 1
Universal Garage Door Opener Remote Control
➡
Motor
Unit &
Receiver
–
LIGHT
SMART-LEARN
BUTTON
Determine the BRAND of the existing garage door opener or handheld remote controls. If all
remote controls are lost, the BRAND is located on the ceiling mounted motor unit or on the
receiver near the flexible wire antenna. Proceed to the SECTION indicated on the BRAND chart
below.
Note: If programming to more than one opener, after programming button “A” refer to brand
chart, and follow the instructions pertaining to the brand you wish to program into button “B”.
When the remotes range is diminished, operation is intermittent, or the LED dims, replace the
battery. Memory is not lost when the battery is removed. Note: Dispose of old batteries
properly.
LED
➡
➡
➡
➡
UP Position is ON
DOWN Position is OFF
1 2 3 4 5 6 7 8 9 10 1112
Note: Use pen or small screwdriver
to move dip switches.
Button A
Button B
Brand Switch
Dip Switch
TYPE
SECTION I SECTION II SECTION III -
KG
ON
LINEAR/MOORE-O-MATIC
OFF ON OFF OFF
Step 1
GREEN SMART-LEARN
BUTTON
ON
ON OFF OFF
➡
Existing
Remote
➡
ON
ON ON OFF
➡
Clicker
Remote
Existing
Remote
➡ Match
➡
Match
existing codes.
Set extra
switches off.
ORANGE/RED
SMART-LEARN BUTTON
Clicker
Remote
OFF ON
ON OFF
➡
release both buttons.
Step 5 - Press the button you wish to operate the
opener (your choice).
Step 6 - Programming is complete, to test, press the
button selected to activate garage door.
➡
SECTION III
- Genie - 9 Code Switch, Genie - 12 Code Switch
➡
Remote
push button
Step 1
KG
Use this
button
GENIE 9 SWITCH
OFF OFF ON OFF
GENIE 12 SWITCH
ON
Proceed to appropriate section.
For type A & B, proceed to step 6. For type C, continue on to Step 5.
Step 5
KG
A. Press and release
Smart-Learn
button.
B. Press and hold button
selected in Step 4 for 3 seconds.
KG
Clicker
Remote
➡ Match
Step 2 - Press and hold both buttons for 5 seconds or until LED begins to flash.
Step 3 - When LED flashes, release both buttons.
Step 4 - Press the button you wish to operate the opener (your choice).
OFF ON OFF
➡
Step 3 - Press and hold
Existing
Remote
Code switch
settings are
not used.
Continue to Step 2.
buttons for 5 seconds
or until LED begins to
flash.
Step 4 - When LED flashes,
existing
codes.
Set extra
switches off.
both buttons for 5
seconds or until LED
begins to flash.
Step 4 - When LED flashes,
➡
existing
codes.
Set extra
switches off.
Code switch
settings are
not used.
– OR –
➡
Step 3 - Press and hold both
Step 2
FOR TYPE C - Step 1
OFF OFF OFF
• Open existing remote; determine if there are 9 or 12 code switch settings.
• Set brand mode switches on clicker remote.
• Program clicker remote push button.
➡
FOR TYPE A AND B
MULTI-CODE
RANDOM 2-9
DO NOT USE
BRAND MODE SETTINGS - Set switches on clicker remote
Battery
Chamberlain, Sears, LiftMaster,
Master Mechanic, DoIt
Stanley, Multi-code, Linear,
Moore-O-Matic
Genie
With this type receiver, the existing remotes do not contain DIP switches.
Proceed to BRAND MODE SETTINGS.
Slide battery
door down
& Remove
BRAND
CHART
✚
–
➡
Preparation
After determining that the Receiver has a yellow, white or gray
learn button, 1) Gather any existing remotes and open to expose
the DIP switches labeled “+”, “0” and “-”. 2) Reset switches: 1 to
“-” and positions 2 through 9 to a random setting using “+” and
the “-”. DO NOT USE THE “0” SETTING, SET ALL REMOTES
TO THE SAME SETTING. On three button remotes the large button is
now programmed to activate the door. 3) The recoded remotes must be
programmed to the receiver. Press and release the smart-learn button.
Then press and hold the existing remote push button for three seconds.
4) Test all the newly coded remote controls to be sure that they operate the
door before proceeding to the BRAND MODE SETTING.
TYPE
OFF OFF OFF OFF
➡
The clicker remote can be programmed to operate up to 2 garage door openers or gates,
including different brands. All programming is done using the:
• Brand switch
• Transmitter DIP switch
• Transmit push buttons A and B, and LED indicator
1 2 3 4
1 2 3 4 5 6 7 8 9
The Receiver DIP switch has three positions labeled “+”, “0”
and “-”. The “0” setting cannot be used with the clicker remote. ✚
RANDOM 2-9
1) Reset switches: 1 to “-” and positions 2 through 9 to a random O
DO NOT USE
–
setting using “+” and the “-”. DO NOT USE THE “O” SETTING.
2) Gather any existing remotes and open to expose the DIP switches. Reset
the DIP switch to match the newly coded receiver. Note: some three button remotes do
➡ Use this
not have a #1 switch. Match the 2 through 9 to the receiver. On three button remotes
button
the large button is now programmed to activate the door. 3) Test all the newly coded
remote controls to be sure that they operate the door before proceeding to the BRAND MODE SETTING.
Remote Control
STANLEY
Step 2
TYPE
Wall Mounted
Control
ON
Step 1
KG
• If the Receiver has 9 DIP switches Proceed to TYPE A
• If the Receiver has a yellow, white, or gray smart-learn button, proceed to TYPE B
• If the Receiver has a green, red, or orange smart-learn button, proceed to TYPE C
LOCK
• Open existing remote to expose code switches.
• Program clicker remote push button.
KG
DIP SWITCHES
ON
➡
✚
- Stanley, Multi-Code, Linear, Moore-O-Matic
• Determine specific brand and circle above.
• Set brand mode switches on clicker remote.
Determine if your motor unit/receiver system has DIP switches or a smart-learn button.
(Locate the small gray wire antenna. Some
models require removing the light lens.)
UP Position is ON
DOWN Position is OFF
SECTION II
SECTION I - Chamberlain, Sears, LiftMaster, Master Mechanic, DoIt
release both buttons.
Step 5 - Press the button you wish to operate the
opener (your choice).
Step 6 - Programming is complete, to test, press the
button selected to activate garage door.
WARNING
To prevent possible SERIOUS INJURY or DEATH from a moving gate or garage door:
• ALWAYS keep remote controls out of reach of children. NEVER permit children to operate, or play
with remote control transmitters.
• Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no
obstructions to door travel.
• ALWAYS keep gate or garage door in sight until completely closed. Never permit anyone to cross
path of moving gate or door.
CAUTION
NOTICE: To comply with FCC and or Industry Canada rules, adjustment or modifications of this receiver and/or transmitter are
prohibited, except for changing the code setting or replacing the battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the following two conditions: (1) this device
may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
TECHNICAL SUPPORT: 800-442-1255 (MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM)
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a Trademark of Overhead Door
Corporation. Linear and Multi-Code are Trademarks of Linear Corporation. Master Mechanic is a Trademark of TruServ.
Sears is a Trademark of Sears & Roebuck. Stanley is a Trademark of The Stanley Works.
DoIt is a trademark of DoIt Best Corporation.
Step 6 - Programming is complete, to test, press the button selected to activate garage door.
114A2504B
©2001, Clicker Corporation
All Rights Reserved
Printed in Mexico

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Create Date                     : 2001:06:25 14:13:25
Producer                        : Acrobat Distiller 4.05 for Macintosh
Author                          : Chamberlain Group
Creator                         : QuarkXPressª: LaserWriter 8 8.7
Title                           : 114A2504 Clicker
Modify Date                     : 2001:06:25 14:13:27-08:00
Page Count                      : 1

EXIF Metadata provided by EXIF.tools