ChargePoint CT1H00 Electric Vehicle Charging Station User Manual Bollard Inst

Download:
Mirror Download [FCC.gov]
Document ID	1071334
Application ID	4rGSiXEyd+ggs1SM/lEa8w==
Document Description	User Manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	95.44kB (1192997 bits)
Date Submitted	2009-02-20 00:00:00
Date Available	2009-02-20 00:00:00
Creation Date	2008-11-25 12:31:11
Producing Software	Adobe PDF library 8.00
Document Lastmod	2009-02-20 17:43:38
Document Title	Bollard Inst
Document Creator	Adobe Illustrator CS3

Coulomb CT1000 Bollard Smartlet Installation Instructions
Part Number: 75-001002-01
Revision 0.1
Copyright
Copyright© 2008 Coulomb Technologies, Inc. All rights reserved.
This material is protected by the copyright laws of the United States and other countries. It
may not be modified, reproduced or distributed without the prior, express written consent
of Coulomb Technologies, Inc.
Safety and Compliance
This manual only covers installation of Coulomb’s Smartlet™ Charging Station and should
not be used for any other product. Before installing the Smartlet Charging Station, you
should review this manual carefully and consult with a licensed contractor, licensed electrician and trained installation expert to ensure compliance with local building practices,
climate conditions, safety standards, and state and local codes.
The Smartlet Charging Station should be installed only by a licensed contractor and a
licensed electrician and in accordance with the U.S. National Electric Code and the
National Fire Protection Association codes and standards. The Smartlet Charging Station
should be inspected by an authorized installer prior to the initial use.
Under no circumstances will compliance with the information in this manual relieve the
user of his/her responsibility for compliance with all applicable codes or safety standards.
No Guarantee as to Accuracy
Reasonable effort was made to ensure that the specifications and other information in this
manual were accurate and complete at the time of its publication. However, the specifications and other information in this manual are subject to change at any time without prior
notice.
Warranty Information and Disclaimer
Your use of or modification to the Smartlet Charging Station in a manner in which the
Smartlet Charging Station is not intended to be used or modified will void the limited
warranty. Other than any such limited warranty, the Coulomb products are provided “AS
IS,” and Coulomb and its distributors expressly disclaim all implied warranties, including
any warranty of design, merchantability, fitness for a particular purposes and noninfringement, to the maximum extent permitted by law.
Limitation of Liability
IN NO EVENT SHALL COULOMB TECHNOLOGIES, INC. OR ITS AUTHORIZED DISTRIBUTORS
BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES, INCLUDING WITHOUT LIMITATION LOST PROFITS, LOST DATA, LOSS OF USE,
COST OF COVER, OR LOSS OR DAMAGE TO THE SMARTLET CHARGING STATION, ARISING
OUT OF OR RELATING TO THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF COULOMB
TECHNOLOGIES, INC. OR ITS AUTHORIZED DISTRIBUTORS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Trademarks
COULOMB TECHNOLOGIES, SMARTLET, and CHARGEPOINT are trademarks or service
marks of Coulomb Technologies, Inc in the U.S. and other countries. All other trademarks
or service marks mentioned in this manual or on the Coulomb Technologies, Inc. website
are the property of their respective owners.
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Documentation
Body
Slide Panel
Base Plate
Ø12.70
Ø149.20
Ø50.80
BOLLARD OUTSIDE ENVELOPE
CONDUIT WITHIN THIS AREA ONLY
FRONT
Base Plate Template
Set Screws (6)
Alan Wrench
Components and Parts:
Body Installation Kit
(shipped to installer)
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
CT1000 Bollard Base Plate Template
NOT TO SCALE
Use this template to properly space the J-Bolts and
conduit piping while casting the footing in place.
Ø 0.50"
12.70 mm
Ø 5.87"
149.18 mm
Ø 2.00"
50.79 mm
BOLLARD OUTSIDE ENVELOPE
7.99"
202.96 mm
CONDUIT WITHIN THIS AREA ONLY
FRONT
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Head Module
Security Screws
Caps for Security Screws
Required Hardware: (installer supplied)
Torx Driver T15 Torx 3" Blade Length 7-1/2", Tamper Resistant
Components and Parts:
Head Module Installation Kit
(shipped to installer)
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Installer supplied:
1. Schedule 40
Galvanized pipe
3 1/2” OD - 3” ID
24“ Long
Rust Sealer
2. Nuts and washers
(to match J-Bolts)
3. J-Bolts (Max 1/2” thread dia)
Length to match Local Code
Installer Supplied Components and Parts
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
1 1/2” Conduit
12" to 24”
or sized to local code
3 J-Bolts(Installer supplied) - Please use
Base Plate Template
2.5" min
18" min
or sized to local code
18" min
or sized to local code
18" min
or sized to local code
Cast Footing in Place - Concrete 18”x18”x18” or sized to local code
J-Bolts, Washers and Nuts Installer Supplied
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
3 Areas for leveling
Attach Base Plate to J-Bolts and
tighten screws.
Nuts and washers
(Installer supplied)
Mount Base Detail
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Debur top edge
Installer supplied
Schedule 40
Galvanized pipe
3 1/2” OD - 3” ID
24” Long
3” NPT, add rust sealer
before installation
Mount Base Assembly
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Ensure the piping is plumb.
Add rust sealer before securing in place.
Level Base Assembly
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Alan wrench
(included)
Set screw 4 places
(included)
Ensure body is level before tightening screws.
Level Body
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Requi
res 15A
branch
White
Neutra
Black
Green
Hot
circuit120vac Inp Ground
and ove ut
rcurre
nt pro
tec
tion on
supply
White
Black
Green
Strip wires back 3/8".
SOLID WIRES ONLY.
Wire Connection
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Use these 3 screws
White Black Green
Neutral Hot Ground
120VAC Input
Requires 15A branch circuit and overcurrent protection on supply
Wire Connection Label
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Wh
Requi
res 15A
Neutr
ch circ 1
uit
Black
Hot
Gro
c Input
overcu
rre
White
otectio
n on sup
ply
Black
Green
View after wires are connected and screwed in place.
Wire Connection
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Ensure the correct end is up and slide the front panel into the body.
THIS
END
UP
Inside Detail View
Set screw (2 places)
Slide front panel into place and lock with set scres (2 places)
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
X
Front Section
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Connect the attached cable from the head module with the connectors in the body.
Slide Head Module into Place
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Torx Driver T15 Torx
3" Blade Length
7-1/2", Tamper-Resistant
Secure Head Module (4 screws)
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Secure Cover Plugs for 4 Screws
Coulomb CT1000 Bollard Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Caution: Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Extract
Page Mode                       : UseNone
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Adobe PDF library 8.00
Modify Date                     : 2009:02:20 17:43:38-08:00
Create Date                     : 2008:11:25 12:31:11-08:00
Metadata Date                   : 2009:02:20 17:43:38-08:00
Creator Tool                    : Adobe Illustrator CS3
Document ID                     : uuid:2e3ccb9d-5ef6-0f42-ab6c-0338dd5beab8
Instance ID                     : uuid:4697062e-0d03-47a0-a1fa-4c46f7093dcd
Format                          : application/pdf
Title                           : Bollard Inst
Has XFA                         : No
Page Count                      : 20
Page Layout                     : SinglePage
Creator                         : Adobe Illustrator CS3

EXIF Metadata provided by EXIF.tools