ChargePoint CT1H00 Electric Vehicle Charging Station User Manual Wall Inst

Download:
Mirror Download [FCC.gov]
Document ID	1071336
Application ID	4rGSiXEyd+ggs1SM/lEa8w==
Document Description	User Manual 3
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	218.62kB (2732732 bits)
Date Submitted	2009-02-20 00:00:00
Date Available	2009-02-20 00:00:00
Creation Date	2008-11-25 13:50:06
Producing Software	Adobe PDF library 8.00
Document Lastmod	2009-02-20 17:44:45
Document Title	Wall Inst
Document Creator	Adobe Illustrator CS3

Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Part Number: 75-001001-01
Revision 0.1
Copyright
Copyright© 2008 Coulomb Technologies, Inc. All rights reserved.
This material is protected by the copyright laws of the United States and other countries. It
may not be modified, reproduced or distributed without the prior, express written consent
of Coulomb Technologies, Inc.
Safety and Compliance
This manual only covers installation of Coulomb’s Smartlet™ Charging Station and should
not be used for any other product. Before installing the Smartlet Charging Station, you
should review this manual carefully and consult with a licensed contractor, licensed electrician and trained installation expert to ensure compliance with local building practices,
climate conditions, safety standards, and state and local codes.
The Smartlet Charging Station should be installed only by a licensed contractor and a
licensed electrician and in accordance with the U.S. National Electric Code and the
National Fire Protection Association codes and standards. The Smartlet Charging Station
should be inspected by an authorized installer prior to the initial use.
Under no circumstances will compliance with the information in this manual relieve the
user of his/her responsibility for compliance with all applicable codes or safety standards.
No Guarantee as to Accuracy
Reasonable effort was made to ensure that the specifications and other information in this
manual were accurate and complete at the time of its publication. However, the specifications and other information in this manual are subject to change at any time without prior
notice.
Warranty Information and Disclaimer
Your use of or modification to the Smartlet Charging Station in a manner in which the
Smartlet Charging Station is not intended to be used or modified will void the limited
warranty. Other than any such limited warranty, the Coulomb products are provided “AS
IS,” and Coulomb and its distributors expressly disclaim all implied warranties, including
any warranty of design, merchantability, fitness for a particular purposes and noninfringement, to the maximum extent permitted by law.
Limitation of Liability
IN NO EVENT SHALL COULOMB TECHNOLOGIES, INC. OR ITS AUTHORIZED DISTRIBUTORS
BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL, PUNITIVE, OR CONSEQUENTIAL
DAMAGES, INCLUDING WITHOUT LIMITATION LOST PROFITS, LOST DATA, LOSS OF USE,
COST OF COVER, OR LOSS OR DAMAGE TO THE SMARTLET CHARGING STATION, ARISING
OUT OF OR RELATING TO THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF COULOMB
TECHNOLOGIES, INC. OR ITS AUTHORIZED DISTRIBUTORS HAVE BEEN ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
Trademarks
COULOMB TECHNOLOGIES, SMARTLET, and CHARGEPOINT are trademarks or service
marks of Coulomb Technologies, Inc in the U.S. and other countries. All other trademarks
or service marks mentioned in this manual or on the Coulomb Technologies, Inc. website
are the property of their respective owners.
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Documentation
Front Panel
Body
Ø7.00
6 PLC
63.50
139.70
400.00
139.70
Wall Mount Bracket
ADA Height 38”
Template for Wall Drill Holes
Bottom Plate
Components and Parts:
Body Installation Kit
(shipped to installer)
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
CT1000 Wall Mount Smartlet Template
2.50"
63.50 mm
Ø 0.28"
7.00 mm
6 PLC
5.50"
139.70 mm
NOT TO SCALE
15.75"
400.00 mm
5.50"
139.70 mm
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Height to bottom of bracket 38” (965.20mm)
(USA ADA height is 48” to display)
Head Module
Security Screws
Caps for Security Screws
Required Hardware: (installer supplied)
Torx Driver T15 Torx 3" Blade Length 7-1/2", Tamper Resistant
Components and Parts:
Head Module Installation Kit
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
6 - 1/4" Lag Screw 1-1/2"
McMaster P/N: 95526A125
6 - Long Lag Screw Anchor
McMaster P/N: 97039A029
(Installer supplied)
Drill Holes for Inserts (6 places)
see supplied template
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
38” Max height above
surface for ADA compliance
Attach Wall Bracket (6 places)
(Installer supplied screws and inserts)
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Attach Body to Wall Bracket with 4 Supplied Screws and Washers
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
3/4” coupling
(Installer supplied)
Attach installer supplied coupler to the wall mounted body and connect conduit.
Connect Conduit
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
White
Black
Green
Strip wires back 3/8".
SOLID WIRES ONLY.
Feed Wire Through Conduit
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Use these 3 screws
White Black Green
Neutral Hot Ground
120VAC Input
Requires 15A branch circuit and overcurrent protection on supply
Wire Connection Label
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Green
Black
White
View after wires are connected and screwed in place.
Connect Wire
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Torx Driver T15 Torx
3" Blade Length
7-1/2", Tamper-Resistant
Attach Bottom Plate
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
1. Slide front panel into place.
2. Tighten set screws with included alan wrench,
in two places.
Inside view with panel in place.
Slide Front Panel into Place
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Connect the attached cable from the head module with the connectors in the body.
Slide Head Module into Place
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Torx Driver T15 Torx
3" Blade Length
7-1/2", Tamper-Resistant
Secure Head Module (4 screws)
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Max height for
ADA is 48”
Secure Cover Plugs for 4 Screws
Coulomb CT1000 Wall Mount Smartlet Installation Instructions
Revision 0.1
PRELIMINARY
Note: This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct
the interference at his own expense.
Caution: Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Extract
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Adobe PDF library 8.00
Modify Date                     : 2009:02:20 17:44:45-08:00
Create Date                     : 2008:11:25 13:50:06-08:00
Metadata Date                   : 2009:02:20 17:44:45-08:00
Creator Tool                    : Adobe Illustrator CS3
Document ID                     : uuid:648a6da0-1389-6c4d-8627-d16917245dce
Instance ID                     : uuid:bec279ba-c299-46e7-92b8-d9daed6f1a68
Format                          : application/pdf
Title                           : Wall Inst
Page Count                      : 18
Page Layout                     : SinglePage
Creator                         : Adobe Illustrator CS3

EXIF Metadata provided by EXIF.tools