ChargePoint CT1H00 Electric Vehicle Charging Station User Manual Wall Inst

ChargePoint, Inc. Electric Vehicle Charging Station Wall Inst

Contents

User Manual 3

Coulomb CT1000 Wall Mount Smartlet Installation InstructionsPart Number: 75-001001-01Revision 0.1
CopyrightCopyright© 2008 Coulomb Technologies, Inc.  All rights reserved.This material is protected by the copyright laws of the United States and other countries. It may not be modied, reproduced or distributed without the prior, express written consent of Coulomb Technologies, Inc.Safety and ComplianceThis manual only covers installation of Coulomb’s Smartlet™ Charging Station and should not be used for any other product.  Before installing the Smartlet Charging Station, you should review this manual carefully and consult with a licensed contractor, licensed elec-trician and trained installation expert to ensure compliance with local building practices, climate conditions, safety standards, and state and local codes.  The Smartlet Charging Station should be installed only by a licensed contractor and a licensed electrician and in accordance with the U.S. National Electric Code and the National Fire Protection Association codes and standards.  The Smartlet Charging Station should be inspected by an authorized installer prior to the initial use.  Under no circumstances will compliance with the information in this manual relieve the user of his/her responsibility for compliance with all applicable codes or safety standards.No Guarantee as to AccuracyReasonable eort was made to ensure that the specications and other information in this manual were accurate and complete at the time of its publication.  However, the specica-tions and other information in this manual are subject to change at any time without prior notice.  Warranty Information and DisclaimerYour use of or modication to the Smartlet Charging Station in a manner in which the Smartlet Charging Station is not intended to be used or modied will void the limited warranty.  Other than any such limited warranty, the Coulomb products are provided “AS IS,” and Coulomb and its distributors expressly disclaim all implied warranties, including any warranty of design, merchantability, tness for a particular purposes and non-infringement, to the maximum extent permitted by law.Limitation of LiabilityIN NO EVENT SHALL COULOMB TECHNOLOGIES, INC. OR ITS AUTHORIZED DISTRIBUTORS BE LIABLE FOR ANY INDIRECT, INCIDENTAL, SPECIAL, PUNITIVE, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION LOST PROFITS, LOST DATA, LOSS OF USE, COST OF COVER, OR LOSS OR DAMAGE TO THE SMARTLET CHARGING STATION, ARISING OUT OF OR RELATING TO THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF COULOMB TECHNOLOGIES, INC. OR ITS AUTHORIZED DISTRIBUTORS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.TrademarksCOULOMB TECHNOLOGIES, SMARTLET, and CHARGEPOINT are trademarks or service marks of Coulomb Technologies, Inc in the U.S. and other countries.  All other trademarks or service marks mentioned in this manual or on the Coulomb Technologies, Inc. website are the property of their respective owners. Coulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Ø6 PLC7.0063.50400.00139.70139.70ADA Height 38”Front PanelTemplate for Wall Drill HolesWall Mount BracketBottom PlateBodyComponents and Parts:Body Installation Kit(shipped to installer)DocumentationCoulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
6 PLCHeight to bottom of bracket 38” (965.20mm)(USA ADA height is 48” to display) 15.75"400.00 mm2.50"63.50 mm5.50"139.70 mm5.50"139.70 mmØ 0.28"7.00 mmCT1000 Wall Mount Smartlet TemplateNOT TO SCALECoulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Components and Parts:Head Module Installation KitHead ModuleSecurity ScrewsCaps for Security ScrewsRequired Hardware: (installer supplied)Torx Driver T15 Torx 3" Blade Length 7-1/2", Tamper ResistantCoulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
see supplied template6 - 1/4" Lag Screw 1-1/2"McMaster P/N: 95526A1256 - Long Lag Screw AnchorMcMaster P/N: 97039A029 (Installer supplied)Drill Holes for Inserts (6 places)Coulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Attach Wall Bracket (6 places)38” Max height abovesurface for ADA compliance(Installer supplied screws and inserts)Coulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Attach Body to Wall Bracket with 4 Supplied Screws and WashersCoulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Connect Conduit3/4” coupling(Installer supplied) Attach installer supplied coupler to the wall mounted body and connect conduit.Coulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Feed Wire Through ConduitWhiteBlackGreenStrip wires back 3/8".SOLID WIRES ONLY.Coulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Wire Connection LabelUse these 3 screwsWhiteNeutral BlackHot120VAC InputRequires 15A branch circuit and overcurrent protection on supplyGreenGroundCoulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Connect WireWhiteBlackGreenView after wires are connected and screwed in place.Coulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Attach Bottom PlateTorx Driver T15 Torx3" Blade Length7-1/2", Tamper-ResistantCoulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
in two places.2. Tighten set screws with included alan wrench,Inside view with panel in place.Slide Front Panel into PlaceCoulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY1. Slide front panel into place.
Connect the attached cable from the head module with the connectors in the body.Slide Head Module into PlaceCoulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Secure Head Module (4 screws)Torx Driver T15 Torx3" Blade Length7-1/2", Tamper-ResistantCoulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Secure Cover Plugs for 4 ScrewsMax height forADA is 48”Coulomb CT1000 Wall Mount Smartlet Installation Instructions       Revision 0.1         PRELIMINARY
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.  Caution: Changes or modifications not expressly approved by the party responsible for compliance               could void the user's authority to operate the equipment.

Navigation menu