Chuango Security Technology P910 PIR Motion Detector User Manual 1
Chuango Security Technology Corporation PIR Motion Detector 1
Users manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2268726 |
| Application ID | WBIStMJCYfKT/yQrqn7LFw== |
| Document Description | Users manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 139.61kB (1745176 bits) |
| Date Submitted | 2014-05-16 00:00:00 |
| Date Available | 2014-05-16 00:00:00 |
| Creation Date | 2014-05-09 18:55:28 |
| Producing Software | Corel PDF Engine Version 16.1.0.843 |
| Document Lastmod | 2014-05-09 18:55:28 |
| Document Title | 未命å -1 |
| Document Creator | CorelDRAW X6 |
| Document Author: | chuango-LS |
Pairing to Control Panel LED ON / OFF Pet-Immune PIR Motion Detector Infrared sensor Tamper switch PIR-910 Control panel enters paring state Make the control panel in paring state. Press the test button Press the test button on the back of the detector twice, the control panel beeps once to indicate a successful pairing. Note: If the control panel beeps twice when the above operation is done, it means the detector has been paired already. User Manual Infrared sensor Zone setting Introduction Infrared sensor: It detects the infrared rays released by human body motion, please don’t touch the surface and always keep it clean. The motion detector is with high performance. It consists of digital dualcore fuzzy logic infrared control chip and intelligent analysis which effectively identify interference signal from body movement signals from Tamper switch: Once the case is opened in work mode, the tamper switch is triggered and then generates an alarm signal. body movement signals and reduce false alarm rate. With automatic temperature compensation and anti-turbulence technology, it easily energy saving, reliability and easy installation. It is suitable for lobby, Testing Mode Press the test button, the detector enters testing mode and detects once every 10 seconds. After 3minutes, the LED indicator blinks twice, and the detector switches to power saving mode. Power Saving Mode This motion detector has smart power saving function. If the detector is triggered twice within 3 minutes, it enters sleeping state immediately to save power. During this period, any movement detected does not generate an alarm. After no movement within the next 3 minutes, it goes back to working state again. adapts to environment changes. The detector also has the advantage of hallway detection with a detective range of 0-8m at front. With low Working Mode Detection Range power feedback function, user will get SMS alert about low battery if the PIR detector is connected to GSM alarm system. Side View Top View Product Overview 1. Detection window 2. LED indicator 3. Snap joint 4. Test button 5. Bracket Pet Immune Function Note: When the detector goes into sleeping state, the precondition of alarm is that no one moves in 3 minutes in the detection area; otherwise it will remain in the sleeping state. If the detector is in sleeping state, it is suggested to leave the room and make sure nobody moves in the detection area. The detector will go back to working state in 3 minutes. Test It is to check whether the PIR Motion Detector can work properly or not. This sensor adopts dual detection window design to improve detection accuracy. It was only when both two detection windows detect body movement will it trigger an alarm. While only one window will not cause an alarm. Based on this principle, pets less than 25 kgs will not be Remove the insulation strip Press down the snap joint, open the case, and remove the insulation strip to activate batteries. After self-testing for 1 minute, it enters working state. detected by the sensor. Arm the system Make sure the alarm system is in armed state. LED Indication Meaning Display Blink continuously Self testing Blink once Intrusion detected Blink twice Testing mode is finished, the detector enters power-saving mode Blink once every 3 seconds Low battery, please replace the battery as soon as possible Trigger an alarm Press the test button until an alarm is triggered. The detector is proved to be connected successfully and ready for installation. Installation Installation Notices Don't face swinging objects Swinging objects may also trigger false alarm. Besides, if there are two detectors covering the save scope, adjust the locations to prevent cross- After making sure the detector works normally, do as follows: Mount the detector to a location close to the entry or exit interference. The detector aims at preventing intrusion. Detecting human movement at Choose a suitable installation location the entry or exit is critical for security. It is recommended to mount it at the height of 2m from the ground. 2m Ground Mount the detector in a proper angle The installation angle affects detection sensitivity. The sensitivity is optimal Fix the detector Fix the bracket on the wall with screws and attach the detector to the bracket. Specifications when the walk direction is vertical to the infrared direction. Choose the best location and angle according to the actual situation and detection scope Power Supply diagram. DC 3V (AA 1.5V LR6 Battery x 2 pcs) Static Current ≤ 90uA Alarm Current ≤ 9.5mA Detection Scope 8m/110° Pet Immunity ≤ 25kgs Transmitting Distance Don't face glass windows or doors Test the PIR motion detector Press the test button at the back. It switches to the testing mode and ≤ 80m (Open area/ no interference) Strong light interferes with detection sensitivity. In addition, complicated Radio Frequency situations, such as traffic flow, stream of people, also should be avoided. 315MHz (±75KHz) sustains for 3 minutes. Walk in the detection scope and observe the LED. Housing Material When body movement is detected, the LED blinks once. ABS plastic Operation Condition Temperature: -10°C~+55°C Relative Humidity: ≤80% (non-condensing) Detector Dimensions (L x W x H) 108 x 52 x 36.8 mm Bracket Dimensions (L x W x H) 52 x 30 x 26.5 mm Don't face or position close to heat sources Adjust the angle Adjust the bracket angle to achieve the best detection effect. Heat and cold sources, such as heat extraction units, heaters, air conditioner, microwave oven, refrigerator, which may cause false alarm, should be avoided. FCC STATEMENT 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and ON (2) This device must accept any interference received, including interference that may cause undesired operation. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: If pet-immune function is applied, please do not adjust the angle up or down, but keep it parallel with the wall. Ver : PIR-910-EN-1405-V6.0 2014 Chuango. All rights reser ved. 产品型号 PIR-900 部件名称 说明书 设 林寿 材 80克书写纸 印刷尺寸 315X285mm 成品尺寸 52.5X95mm 工 折页 版 Ver: PIR-910-EN-1405-V6.0 计 艺 注: 双色、单面印刷 料 本
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Page Count : 3 Create Date : 2014:05:09 18:55:28+08:00 Modify Date : 2014:05:09 18:55:28+08:00 Producer : Corel PDF Engine Version 16.1.0.843 Author : chuango-LS Creator : CorelDRAW X6 Title : 未命名 -1EXIF Metadata provided by EXIF.tools