CipherLab 1660 Barcode Scanner User Manual
CipherLab Co., Ltd. Barcode Scanner
User manual
1660 Barcode Scanne
r
Setup labels included.
Copyright © 2008 CIPHERLAB CO., LTD.
All rights reserved
The software contains proprietary information of CIPHERLAB CO., LTD.; it is provided
under a license agreement containing restrictions on use and disclosure and is also
protected by copyright law. Reverse engineering of the software is prohibited.
Due to continued product development this information may change without notice. The
information and intellectual property contained herein is confidential between CIPHERLAB
and the client and remains the exclusive property of CIPHERLAB CO., LTD. If you find
any problems in the documentation, please report them to us in writing. CIPHERLAB
does not warrant that this document is error-free.
No part of this publication may be reproduced, stored in a retrieval system, or
transmitted in any form or by any means, electronic, mechanical, photocopying,
recording or otherwise without the prior written permission of CIPHERLAB CO., LTD.
For product consultancy and technical support, please contact your local sales
representative. Also, you may visit our web site for more information.
The CipherLab logo is a registered trademark of CIPHERLAB CO., LTD.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and/or other countries.
Bluetooth is a trademark of Bluetooth SIG, Inc., U.S.A.
Other product names mentioned in this manual may be trademarks or registered
trademarks of their respective companies and are hereby acknowledged.
The editorial use of these names is for identification as well as to the benefit of the
owners, with no intention of infringement.
CIPHERLAB CO., LTD.
Website: http://www.cipherlab.com
FOR USA
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
FOR CANADA
This digital apparatus does not exceed the Class B limits for radio noise emissions from
digital apparatus as set out in the interference-causing equipment standard entitled
"Digital Apparatus," ICES-003 of Industry Canada.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
Cet appareil numerique respecte les limites de bruits radioelectriques applicables aux
appareils numeriques de Classe B prescrites dans la norme sur le material brouilleur:
"Appareils Numeriques," NMB-003 edictee par l'Industrie.
FOR HAND-HELD PRODUCT WITH RF FUNCTIONS
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20
cm between the radiator & your body.
IMPORTANT NOTICES
You are cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
It only operated in hand-held used. If you only transfer data to Host by Bluetooth,
please keep the minimum distance 20 cm between machine & your body.
FOR PRODUCT WITH LASER
Per FDA and IEC standards, the scan engines described in this manual are not given a
laser classification. However, the following precautions should be observed:
CAUTION
This laser component emits FDA / IEC Class 2 laser light at the exit port. Do not
stare into beam.
SAFETY PRECAUTIONS
RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
The use of any batteries or charging devices, which are not originally sold or
manufactured by CipherLab, will void your warranty and may cause damage to
human body or the product itself.
DO NOT disassemble, incinerate or short circuit the battery.
DO NOT expose the scanner or the battery to any flammable sources.
For green-environment issue, it's important that batteries should be recycled in a
proper way.
Under no circumstances, internal components are self-serviceable.
The charging and communication cradle uses an AC power adaptor. A socket outlet
shall be installed near the equipment and shall be easily accessible. Make sure there
is stable power supply for the mobile computer or its peripherals to operate properly.
CARE & MAINTENANCE
Use a clean cloth to wipe dust off the scanning window and the body of the scanner
as well as the cradle. DO NOT use/mix any bleach or cleaner.
If you want to put away the scanner for a period of time, download the collected data
to a host computer when in the memory mode, and then take out the battery. Store
the scanner and battery separately.
When the scanner resumes its work, make sure the battery is fully charged before
use.
If you shall find the scanner malfunctioning, write down the specific scenario and
consult your local sales representative.
Version Date Notes
0.94 Mar. 19, 2008 Modified: section 1.6.6 Aiming Mode – Timeout (1~15 sec)
New: section 4 Changing Symbology Settings – ISBT 128
0.93 Feb. 26, 2008 Modified: remove 1662
0.92 Feb. 15, 2008 Modified: section 2.1.3 Keyboard Settings – illustration
0.91 Feb. 14, 2008 Separate manual for1660 for review
0.90 Jan. 25, 2008 Draft for use in pilot production
* The documentation is subject to change without prior notice.
RELEASE NOTES
CONTENTS
IMPORTANT NOTICES ...................................................................................................................... - 3 -
For USA .......................................................................................................................................... - 3 -
For Canada .................................................................................................................................... - 3 -
For Hand-held Product with RF Functions ................................................................................... - 3 -
For Product with Laser .................................................................................................................. - 4 -
Safety Precautions ........................................................................................................................ - 4 -
Care & Maintenance ..................................................................................................................... - 4 -
RELEASE NOTES .............................................................................................................................. - 5 -
INTRODUCTION .................................................................................................................................... 1
Inside the Package............................................................................................................................ 2
Product Highlights ............................................................................................................................. 2
Quick Start ........................................................................................................................................... 3
Enter Configuration Mode................................................................................................................. 4
Exit Configuration Mode.................................................................................................................... 4
Default Settings................................................................................................................................. 5
Save User Settings as Defaults................................................................................................... 5
Restore User Defaults.................................................................................................................. 5
Restore System Defaults ............................................................................................................. 5
Read a Setup Label........................................................................................................................... 6
Configure Parameters.................................................................................................................. 6
List the Current Settings.............................................................................................................. 9
UNDERSTANDING THE BARCODE SCANNER....................................................................................11
1.1 Battery .......................................................................................................................................11
1.1.1 Installing the Battery........................................................................................................11
1.1.2 How to Operate the Scanner ...........................................................................................12
1.1.3 Auto Power Off..................................................................................................................12
1.2 Memory .....................................................................................................................................13
1.2.1 Transmit Buffer ................................................................................................................13
1.2.2 Memory Mode ..................................................................................................................13
1.3 LED Indicator.............................................................................................................................15
1.3.1 Good Read LED ................................................................................................................16
1.4 Beeper.......................................................................................................................................16
1.4.1 Beeper on 1660...............................................................................................................16
1.4.2 Beeper Volume.................................................................................................................17
1.4.3 Good Read Beep ..............................................................................................................17
1.4.4 Low Battery Alarm ............................................................................................................18
1.5 Send “NR” to Host ....................................................................................................................19
1.6 Scan Modes ..............................................................................................................................19
1.6.1 Continuous Mode.............................................................................................................20
1600 Series Barcode Scanner User Guide
1.6.2 Test Mode.........................................................................................................................21
1.6.3 Laser Mode.......................................................................................................................21
1.6.4 Auto Off Mode...................................................................................................................21
1.6.5 Auto Power Off Mode .......................................................................................................22
1.6.6 Aiming Mode..................................................................................................................... 22
1.6.7 Multi-Barcode Mode.........................................................................................................23
1.7 Scanning Timeout.....................................................................................................................23
1.8 Delay between Re-read ............................................................................................................24
1.9 Effective Decoding Area ........................................................................................................... 25
1.9.1 Positioning Window..........................................................................................................25
1.9.2 Adjusting Window.............................................................................................................25
1.10 Negative Barcodes .................................................................................................................27
1.11 Symbologies Supported.........................................................................................................27
1.11.1 Read Redundancy for All Symblogies...........................................................................28
1.11.2 Addon Security for UPC/EAN Barcodes ........................................................................28
SELECTING OUTPUT INTERFACE .......................................................................................................31
2.1 Bluetooth HID............................................................................................................................31
2.1.1 Activate Bluetooth HID & Select Keyboard Type............................................................32
2.1.2 Reset Connection.............................................................................................................32
2.1.3 Keyboard Settings............................................................................................................33
2.1.4 Inter-Function Delay.........................................................................................................36
2.2 Bluetooth SPP...........................................................................................................................38
2.2.1 Activate Bluetooth SPP ....................................................................................................38
2.2.2 Inter-Function Delay.........................................................................................................38
2.2.3 ACK/NAK Timeout............................................................................................................39
SETTING UP BLUETOOTH CONNECTIONS .........................................................................................41
3.1 Configuring Bluetooth Settings................................................................................................42
3.1.1 Sniff Mode (Power-saving)...............................................................................................42
3.1.2 Device Name Broadcasting ............................................................................................. 42
3.1.3 Authentication ..................................................................................................................43
3.2 Connecting via Bluetooth Dongle ............................................................................................44
3.2.1 Bluetooth HID – Add Bluetooth Device Wizard ..............................................................44
3.2.2 Bluetooth SPP – Add Bluetooth Device Wizard..............................................................44
CHANGING SYMBOLOGY SETTINGS.................................................................................................. 51
4.1 Codabar.....................................................................................................................................52
4.1.1 Start/Stop Characters Selection .....................................................................................52
4.1.2 Start/Stop Transmission..................................................................................................52
4.1.3 CLSI Conversion ...............................................................................................................53
4.2 Code 25 – Industrial 25...........................................................................................................54
4.2.1 Start/Stop Pattern Selection ...........................................................................................54
4.2.2 Checksum Verification .....................................................................................................54
4.2.3 Checksum Transmission..................................................................................................55
4.2.4 Code Length Qualification ...............................................................................................55
4.3 Code 25 – Interleaved 25........................................................................................................57
4.3.1 Start/Stop Pattern Selection ...........................................................................................57
4.3.2 Checksum Verification .....................................................................................................57
4.3.3 Checksum Transmission..................................................................................................58
1600 Series Barcode Scanner User Guide
4.3.4 Code Length Qualification ...............................................................................................58
4.4 Code 25 – Matrix 25 ................................................................................................................ 60
4.4.1 Start/Stop Pattern Selection ...........................................................................................60
4.4.2 Checksum Verification .....................................................................................................60
4.4.3 Checksum Transmission..................................................................................................61
4.4.4 Code Length Qualification ...............................................................................................61
4.5 Code 39.....................................................................................................................................63
4.5.1 Start/Stop Transmission..................................................................................................63
4.5.2 Checksum Verification .....................................................................................................63
4.5.3 Checksum Transmission..................................................................................................64
4.5.4 Standard/Full ASCII Code 39 ..........................................................................................64
4.6 Code 93.....................................................................................................................................65
4.7 Code 128 ..................................................................................................................................65
4.8 EAN-8.........................................................................................................................................66
4.8.1 Convert to EAN-13............................................................................................................66
4.8.2 Checksum Transmission..................................................................................................67
4.9 EAN-13 ......................................................................................................................................68
4.9.1 ISBN Conversion...............................................................................................................68
4.9.2 ISSN Conversion...............................................................................................................69
4.9.3 Checksum Transmission..................................................................................................69
4.10 EAN-128..................................................................................................................................70
4.10.1 Code ID Transmission.................................................................................................... 70
4.10.2 Field Separator (GS Character).....................................................................................70
4.11 ISBT 128 .................................................................................................................................71
4.12 MSI ..........................................................................................................................................72
4.12.1 Checksum Verification................................................................................................... 72
4.12.2 Checksum Transmission ...............................................................................................72
4.12.3 Code Length Qualification .............................................................................................73
4.13 French Pharmacode...............................................................................................................75
4.13.1 Checksum Transmission ...............................................................................................75
4.14 Italian Pharmacode ................................................................................................................76
4.14.1 Checksum Transmission ...............................................................................................76
4.15 Plessey ....................................................................................................................................77
4.15.1 Convert to UK Plessey ...................................................................................................77
4.15.2 Checksum Transmission ...............................................................................................77
4.16 RSS Family..............................................................................................................................78
4.16.1 Code ID Selection ..........................................................................................................78
4.16.2 RSS-14............................................................................................................................78
4.16.3 RSS Expanded................................................................................................................79
4.16.4 RSS Limited.................................................................................................................... 80
4.17 Telepen ...................................................................................................................................82
4.17.1 Telepen Output – Full ASCII/Numeric ..........................................................................82
4.18 UPC-A.......................................................................................................................................83
4.18.1 Convert to EAN-13 .........................................................................................................83
4.18.2 System Number Transmission ......................................................................................84
4.18.3 Checksum Transmission ...............................................................................................84
4.19 UPC-E....................................................................................................................................... 85
4.19.1 System Number Selection.............................................................................................85
1600 Series Barcode Scanner User Guide
4.19.2 Convert to UPC-A............................................................................................................86
4.19.3 System Number Transmission ......................................................................................86
4.19.4 Checksum Transmission ...............................................................................................86
DEFINING OUTPUT FORMAT..............................................................................................................89
5.1 Letter Case................................................................................................................................89
5.2 Character Substitution .............................................................................................................90
5.2.1 Select a Set for Character Substituion ...........................................................................90
5.2.2 Symbologies for Character Substitution (All 3 Sets) ...................................................... 91
5.3 Prefix/Suffix Code.....................................................................................................................96
5.4 Code ID......................................................................................................................................97
5.4.1 Select Pre-defined Code ID..............................................................................................97
5.4.2 Change Code ID................................................................................................................98
5.4.3 Clear Code ID Settings...................................................................................................100
5.5 Length Code............................................................................................................................101
5.6 Multi-Barcode Editor...............................................................................................................104
5.6.1 Edit a Concatenation of Barcodes ................................................................................105
5.6.2 Activate the Concatenation of Barcodes ......................................................................106
APPLYING FORMATS FOR DATA EDITING........................................................................................107
6.1 Format Selection ....................................................................................................................108
6.1.1 Activate Editing Formats................................................................................................108
6.1.2 Exclusive Data Editing....................................................................................................109
6.2 Editing Format.........................................................................................................................110
6.2.1 Select Format to Configure............................................................................................110
6.2.2 Restore Default Format .................................................................................................111
6.2.3 Define Data Criteria .......................................................................................................112
6.2.4 Divide Data into Fields...................................................................................................115
6.2.5 Field Settings..................................................................................................................117
6.2.6 Field Transmission Sequence .......................................................................................121
6.3 Programming Examples .........................................................................................................123
6.3.1 Example I ........................................................................................................................123
6.3.2 Example II .......................................................................................................................123
SPECIFICATIONS ..............................................................................................................................125
NUMERAL SYSTEMS........................................................................................................................127
Decimal System.............................................................................................................................127
Hexadecimal System.....................................................................................................................128
Entering PIN Code for Bluetooth Connection ..............................................................................129
KEYBOARD WEDGE TABLE & ASCII TABLE......................................................................................131
Keyboard Wedge Table .................................................................................................................131
Key Type....................................................................................................................................131
Key Status ................................................................................................................................132
User-defined Scan Code ..........................................................................................................133
ASCII Table.....................................................................................................................................133
HOST SERIAL COMMANDS ..............................................................................................................135
Serial Commands..........................................................................................................................135
1600 Series Barcode Scanner User Guide
Example .........................................................................................................................................136
UPGRADING FIRMWARE..................................................................................................................137
1
CipherLab’s new small-form-factor 1600 Series Barcode Scanners are specifically
designed to answer your mobile demands. The palm-sized 1660 scanners are designed to
help accelerate productivity while lowering the total cost of ownership. Intensive data
collection jobs are made easier with fast, accurate barcode scanning in various working
environments, especially in small businesses. Integrating Bluetooth technology to
small-form-factor scanners, the 1660 Bluetooth scanners are ideal for carrying in your
pocket, and thus give workers tether-free mobility anytime anywhere and get job done
more efficiently. This line of Bluetooth scanners has a range of up to 3 meters and a
prolonged battery life that provides up to 30 hours uptime to keep business running.
Owing to the compact design, extremely low power consumption, and powerful decoding
capability, CipherLab Barcode Scanners are the best choice for the following
applications –
Receiving in Retail
Product labeling & Tracking
Shelf Product Replenishment
Mobile Point of Sale (POS)
Mobile Inventory Management
Order Picking & Staging
Work-In-Process Tracking
Material Flow Control
Transportation & Distribution
Warehousing
Asset Management
This manual contains information on operating the scanner and using its features. We
recommend you to keep one copy of the manual at hand for quick reference or
maintenance purposes. To avoid any improper disposal or operation, please read the
manual thoroughly before use.
Thank you for choosing CipherLab products!
INTRODUCTION
2
1600 Series Barcode Scanner User Guide
INSIDE THE PACKAGE
The items included in the package may be different, depending on your order. Save the
box and packaging material for future use in case you need to store or ship the scanner.
1660 Barcode Scanner
Manual & Driver CD
Note: The Manual & Driver CD includes this manual and Windows-based ScanMaster
software for configuration.
PRODUCT HIGHLIGHTS
Small-form-factor and built tough to survive drop test
Most popular barcode symbologies are supported, including Reduced Space
Symbology (RSS)
Negative barcodes are also supported
Seven scan modes are supported, including Aiming Mode and Multi-Barcode Mode
User feedback via LED indicator and beeper
Beeping tone and duration are programmable for Good Read.
Extremely low power consumption
128 KB flash memory for Memory mode operation, storing up to 8192 scans.
The 1660 scanner provides up to 4 KB SRAM for reserve buffer, storing up to 256
scans while getting out of range during a Bluetooth connection.
Bluetooth Serial Port Profile (SPP) supported – for example, the 1660 scanner can
transmit the scanned data to a Bluetooth-enabled computer or PDA.
Bluetooth Human Interface Device (HID) supported – for example, the 1660 scanner
can transmit the scanned data to a Bluetooth-enabled computer or PDA, as keyboard
input.
Programmable parameters include data output format, editing format, symbologies,
etc.
Firmware upgradeable
3
The configuration of the scanner can be done by reading the setup labels contained in
this manual or via the ScanMaster software.
This section describes the procedure of configuring the scanner by reading the setup
barcodes and provides some examples for demonstration.
Note: If RS-232 or Bluetooth SPP is selected for output interface, the host can directly
send serial commands to configure the scanner.
Steps Action User Feedback if Successful
1 Power on the scanner… The scanner will respond with a long beep
(high tone).
Note: Upon powering up, the 1660 scanner will try to establish a connection with a
Bluetooth device dongle. Refer to Chapter 3 – Setting up Bluetooth Connections
for details.
2 Enter the Configuration Mode… The scanner will respond with six beeps
(high-low tone repeats three times), and
its LED indicator will be flashing red.
3 Read a Setup label…
For example,
The scanner will respond with two beeps
(low-high tone) if reading a normal label.
4 Exit the Configuration Mode…
OR
Same as for Enter the Configuration Mode.
5 The scanner will automatically restart itself… Same as for Power on the scanner.
* When any configuration error occurs... The scanner will respond with one long
beep with a low tone.
Quick Start
4
1600 Series Barcode Scanner User Guide
ENTER CONFIGURATION MODE
For the scanner to enter the configuration mode, you must have it read the "Enter Setup"
label, which can be located at the bottom of almost every even page of this manual.
The scanner will respond with six beeps and its LED indicator will become flashing red
after reading the label.
For configuring scanner parameters, see “Read a Setup Label” below.
EXIT CONFIGURATION MODE
For the scanner to exit the configuration mode, you must have it read the “Update” label,
which can be located at the bottom of almost every odd page of this manual. If you want
to exit the configuration mode without saving any changes, have the scanner read the
“Abort” label instead.
Just like reading the “Enter Setup” label, the scanner will respond with six beeps and
its LED indicator will become flashing red after reading the label. Wait for a few
seconds for the scanner to restart itself.
Enter Setup
Update
Abort
5
!
DEFAULT SETTINGS
SAVE USER SETTINGS AS DEFAULTS
For the scanner to keep the customized settings as user defaults, you must have it read
the “Save as User Defaults” label.
RESTORE USER DEFAULTS
For the scanner to restore the user defaults, which you have saved earlier, you must
have it read the “Restore User Defaults” label.
The scanner will issue two beeps after reading the label, and all the parameters of the
scanner will return to their customized values.
RESTORE SYSTEM DEFAULTS
For the scanner to restore the factory defaults, you must have it read the “Restore
System Defaults” label.
The scanner will issue two beeps after reading the label, and all the parameters of the
scanner will return to their default values.
Note: The system default value (if there is) for each setting is indicated by an asterisk
“*”.
Save as User Default
Restore User Defaults
Restore System Defaults
6
1600 Series Barcode Scanner User Guide
READ A SETUP LABEL
CONFIGURE PARAMETERS
For most of the scanner parameters, only one read is required to set them to new values.
The scanner will respond with two beeps when each parameter is set successfully.
But for a number of special parameters, multiple reads are required to complete the
setting. In this case, the scanner will respond with a short beep to indicate it needs to
read more setup labels. These special parameters may require reading one or more (1)
numeric labels, say, for keyboard type, inter-character delay, length qualification, or (2)
hexadecimal labels, say, for character strings as prefix, suffix, etc.
Note: When “Keyboard Wedge” is configured for interface, Key Type and Key Status will
then become applicable. You may decide whether or not to apply Key Status when
“Normal Key” is selected for Key Type.
To complete the configuration of these special parameters, it requires reading the
“Validate” label, and the scanner will respond with two beeps (low-high tone) to indicate
the input values are validated.
7
!
NUMERIC PARAMETERS
Steps Action User Feedback if Successful
1 Power on the scanner... The scanner will respond with a long beep
(high tone).
2 Enter the Configuration Mode… The scanner will respond with six beeps
(high-low tone repeats three times), and
its LED indicator will become flashing red.
Read a Setup label...
For example,
The scanner will respond with two beeps
(low-high tone) if reading a normal label.
3
The scanner will respond with one short
beep if reading a special label such as
“Max. Length”, indicating the setup
requires reading more labels.
The scanner will respond with two beeps
(low-high tone) when the input values are
validated.
4 Exit the Configuration Mode…
OR
Same as for Enter the Configuration Mode.
Normal label
Normal label
Special label
Decimal label
or labels
8
1600 Series Barcode Scanner User Guide
CHARACTER STRING PARAMETERS
Steps Action User Feedback if Successful
1 Power on the scanner... The scanner will respond with a long beep
(high tone).
2 Enter the Configuration Mode… The scanner will respond with six beeps
(high-low tone repeats three times), and
its LED indicator will become flashing red.
Read a Setup label...
For example,
The scanner will respond with one short
beep if reading a special label such as
“Prefix Code”, indicating the setup
requires reading more labels.
When “Keyboard Wedge” is configured for
interface, Key Type and Key Status will
then become applicable.
You may decide whether or not to
apply Key Status when “Normal Key”
is selected for Key Type.
3
Read the “Hexadecimal Value” label for
the desired character string. For example,
read “2” and “B” for the scanner to prefix
the character “+”.
The scanner will respond with two beeps
(low-high tone) when the input values are
validated.
4 Exit the Configuration Mode…
OR
Same as for Enter the Configuration Mode.
S
p
ecial label
Hexadecimal
labels
9
!
LIST THE CURRENT SETTINGS
The current settings of all scanner parameters can be sent, via RS-232 or Bluetooth SPP,
to the host computer for user inspection. The listing includes ten pages as shown below.
You can select the page of interest by reading the “Page x” label.
List settings regarding Interface, Buzzer, and
Other Scanner Parameters
List settings regarding Prefix, Postfix, and
Length Code Setting
List settings regarding Code ID
List settings regarding: Readable
Symbologies
List settings regarding Symbology Parameters
(1/3)
List settings regarding Symbology Parameters
(2/3)
List settings regarding Symbology Parameters
(3/3)
List Page 1
List Page 2
List Page 3
List Page 4
List Page 5
List Page 6
List Page 7
10
1600 Series Barcode Scanner User Guide
List settings regarding Editing Format 1
List settings regarding Editing Format 2
List settings regarding Editing Format 3
List settings regarding Editing Format 4
List settings regarding Editing Format 5
List Page 8
List Page 10
List Page 11
List Page 12
11
Update
This chapter explains the features and usage of the barcode scanner.
IN THIS CHAPTER
1.1 Battery..................................................................... 11
1.2 Memory.................................................................... 13
1.3 LED Indicator ............................................................ 15
1.4 Beeper ..................................................................... 16
1.5 Send "NR" to Host...................................................... 19
1.6 Scan Modes .............................................................. 19
1.7 Scanner Time-out ...................................................... 23
1.8 Delay between Re-read............................................... 24
1.9 Effective Decoding Area .............................................. 25
1.10 Negative Barcodes ................................................... 27
1.11 Symbologies Supported ............................................ 27
1.1 BATTERY
The scanner is powered by two AAA Alkaline batteries. During normal operation, the
scanner can work for over 30 hours or 28,000 scans (based on UPC-E barcodes, 1 scan
per 5 seconds). For intensive data collection, you may prepare spare batteries for
non-stop operation.
Note: The 1660 scanner can be configured to save battery power. Refer to settings of
“Auto Power Off”, “Sniff Mode”, as well as “Low Battery Alarm”.
1.1.1 INSTALLING THE BATTERY
1) Hold the scanner face down in one hand.
2) Press the battery lid release and slide the battery lid.
3) Remove the battery lid by the other hand.
4) Install two AAA Alkaline batteries into the battery compartment, each in the right
direction.
Chapter 1
UNDERSTANDING THE BARCODE SCANNER
12
Enter Setup
1600 Series Barcode Scanner User Guide
5) Replace the battery lid and lock it firmly.
1.1.2 HOW TO OPERATE THE SCANNER
To turn on the scanner, press the [Delete] key for 3 seconds, and the scanner will
respond with a long beep (high tone).
To turn off the scanner, press the [Delete] key for 1.5 seconds. The scanner will
respond with short beep (high tone) and the LED will become solid green, then go off,
and finally become solid red. Release the key then.
To delete the last collected data, press the [Delete] key. The scanner will respond
with short beep (high tone) and the LED will become solid green. Before the LED goes
off (within 1 second), press the [Delete] key again to confirm the deletion.
1.1.3 AUTO POWER OFF
Specify the time interval (1~254 min.; 0= disable) for the scanner to wait for a computer
to establish a connection via a Bluetooth dongle. By default, the 1660 scanner will stay
active for 10 minutes waiting for a connection request. If it fails to connect within the
time interval, the scanner will automatically turn off in order to conserve battery power
(you will hear three short beeps, tone descending from high to low). Press the [Delete]
key for 3 seconds to turn it on. On your computer, you will have to search Bluetooth
devices again.
Once a Bluetooth connection is established successfully, the scanner will stay active as
long as the COM port is opened by a host application.
1) Read the label above to specify the time interval before the scanner automatically
turns off.
2) Read the “Decimal Value” label on page 123. For example, read “1” and “5” for the
scanner to automatically turn off after being idle for 15 minutes.
3) Read the “Validate” label on the same page to complete this setting.
Auto Off after 0~254 minutes (*10)
13
Update
Chapter 1 !Ζ
1.2 MEMORY
The collected data can be sent back to a host computer one by one via the transmit
buffer (SRAM) or stored in flash memory when the scanner is set to Memory mode.
1.2.1 TRANSMIT BUFFER
The 1 KB transmit buffer on the scanner can store up to 64 scans based on EAN-13
barcodes. When it is used up, the scanner will respond with one long beep (low tone) as
a warning.
You are advised to get back to range if using the Bluetooth scanner.
1.2.2 MEMORY MODE
The scanner keeps 128 KB flash memory for memory mode operation. When the 1660
scanner is in memory mode, it means Bluetooth connection is disabled.
Warning: Bluetooth cannot work unless memory mode is disabled.
MEMORY DATA DELAY
You may set a delay between each data record while transmitting data back to the
server.
Enable Memory Mode
*Disable Memory Mode
*None
250 ms
14
Enter Setup
1600 Series Barcode Scanner User Guide
SEND DATA
The 128 KB flash memory on the scanner can store up to 8192 scans based on EAN-13
barcodes. When it is used up, the scanner will respond with two short beeps (low-high
tone) as a warning. You are advised to send data to the server immediately. Select a
desired interface for transmission. For example, disable memory mode and use Bluetooth
SPP to transmit data.
Send Data
1 sec
2 sec
3 sec
5 sec
8 sec
500 ms
15
Update
Chapter 1 !Ζ
CLEAR DATA & CONFIRM
Even though data has been sent back to the server, the flash memory is still occupied
unless you erase the memory by having the scanner read two labels – “Clear Data” and
“Confirm”.
1) Read the “Clear Data” label to clear the flash memory.
2) Read the “Confirm” label to confirm the action.
1.3 LED INDICATOR
The triple-color LED on top of the scanner is used to provide user feedback. For example,
the LED becomes solid red and goes off quickly (= Standby mode) upon powering on or
running out of transmit buffer. You may tell the difference by the beeps – for example,
you will hear a long beep of high tone when powering on the scanner, and a long beep of
low tone when the transmit buffer becomes full.
LED – Red/Green/Blue Meaning
Green, and goes off quickly, and
becomes red, and finally goes off
when the [Delete] key is
released.
Power off
Red, and goes off quickly Power on, with one long beep (high tone)
Transmit buffer full, with one long beep (low tone)
Memory full, with two short beeps (low-high tone)
Bluetooth connection out of range, with two beeps
(high-low tone)
Green, and goes off quickly Good Read, beeper pitch and duration programmable
Flashing blue (On/Off ratio 1:1) No Bluetooth connection (flashing slowly)
Dynamic PIN code request from host (flashing quickly)
Flashing blue (On/Off ratio 1:6) Bluetooth connection established
Flashing blue and red Dynamic PIN code input error
Flashing red Configuration Mode
Clear Data
Confirm
16
Enter Setup
1600 Series Barcode Scanner User Guide
1.3.1 GOOD READ LED
1.4 BEEPER
The scanner has a buzzer to provide user feedback in various operating conditions.
1.4.1 BEEPER ON 1660
Beeping Meaning
One long beep, high tone Power on
One short beep, low tone Power off
One short beep, high tone
Programmable, default to 4 KHz
Good Read
Six short beeps
High-low tone repeats three times
Enter Configuration Mode
Exit Configuration Mode
Two short beeps, low-high tone Setup label read successfully
One short beep, high tone More setup label required
One long beep, low tone Transmit Buffer Full
Configuration Error (Wrong label…)
Two short beeps, low-high tone Memory Mode – Memory Full
Two long beeps, high-low tone Multi-Barcode Mode – Buffer Full
Three short beeps
Tone ascending from low to high
Bluetooth connection established
Bluetooth connection resumed
Two beeps, high-low tone Bluetooth connection out of range
Three short beeps, low tone No Bluetooth connection
*Enable Good Read LED
Disable Good Read LED
17
Update
Chapter 1 !Ζ
1.4.2 BEEPER VOLUME
1.4.3 GOOD READ BEEP
FREQUENCY
Mute
Medium Volume
*Maximum Volume
8 kHz
* 4 kHz
2 kHz
1 kHz
Minimum Volume
18
Enter Setup
1600 Series Barcode Scanner User Guide
DURATION
1.4.4 LOW BATTERY ALARM
By default, “2.6 V (Alkaline)” is selected for low battery level. When the battery level
inside the 1660 scanner reaches 2.6 V, it will activate the beeper to give a warning. If
you are using Ni-MH batteries, select “2.1 V (Ni-MH)”.
*Shortest
Longer
Longest
Shorter
No Alarm
* 2.6 V (Alkaline)
2.1 V (Ni-MH)
19
Update
Chapter 1 !Ζ
1.5 SEND “NR” TO HOST
This feature only works when Keyboard Wedge, RS-232, Bluetooth HID, or Bluetooth SPP
is selected for output interface. You may have the scanner send the “NR” string to the
host to notify the No Read event.
1.6 SCAN MODES
There are eight scan modes supported – select the scan mode that best suits the
requirements of a specific application. Refer to the comparison table below.
Scan Mode Start to Scan Stop Scanning
Always Press
trigger
once
Hold
trigger
Press
trigger
twice
Release
trigger
Press
trigger
once
Barcode
being
read
Timeout
Continuous mode 9
Test mode 9
Laser mode 9999
Auto Off mode 9 99
Auto Power Off
mode
9 9
Aiming mode 999
Multi-Barcode
mode
99
Note: By default, the scan mode is set to Laser mode.
Enable
*Disable
20
Enter Setup
1600 Series Barcode Scanner User Guide
1.6.1 CONTINUOUS MODE
The scanner is always scanning.
To decode the same barcode repeatedly, move away the scan beam and target it at
the barcode for each scanning.
Note: Refer to “Delay between Re-read”.
DECODING DELAY
Set the time interval between each decoding.
Continuous Mode
*Disable
0.5 sec
1 sec
2 sec
21
Update
Chapter 1 !Ζ
1.6.2 TEST MODE
The scanner is always scanning.
Capable of decoding the same barcode repeatedly, for testing purpose.
1.6.3 LASER MODE
The scanner will start scanning once the trigger is hold down.
The scanning won't stop until (1) a barcode is decoded, (2) the pre-set timeout
expires, or (3) you release the trigger.
Note: Refer to “Scanning Timeout”.
1.6.4 AUTO OFF MODE
The scanner will start scanning once the trigger is pressed.
The scanning won't stop until (1) a barcode is decoded, and (2) the pre-set timeout
expires.
Note: Refer to “Scanning Timeout”.
Test Mode
*Laser Mode
Auto Off Mode
22
Enter Setup
1600 Series Barcode Scanner User Guide
1.6.5 AUTO POWER OFF MODE
The scanner will start scanning once the trigger is pressed.
The scanning won't stop until the pre-set timeout expires, and, the pre-set timeout
period re-counts after each successful decoding.
Note: Refer to “Delay between Re-read” and “Scanning Timeout”.
1.6.6 AIMING MODE
The scanner will aim at a barcode once the trigger is pressed, and start scanning when
the trigger is pressed again within one second.
The scanning won't stop until (1) a barcode is decoded, and (2) the pre-set timeout
expires.
AIMING TIMEOUT
You can limit the aiming time interval (1~15). By default, the scanner time-out is set to
1 second.
1) Read the label above to specify the time interval before aiming ends. (It is set to 1 by
default.)
2) Read the “Decimal Value” label on page 123. For example, read “1” and “0” for the
scanner to automatically shut down after being idle for 10 seconds.
3) Read the “Validate” label on the same page to complete this setting.
Auto Power Off Mode
Aiming Mode
Aiming Time-Out after 1
~
15 seconds (*1)
23
Update
Chapter 1 !Ζ
1.6.7 MULTI-BARCODE MODE
The scanner will be scanning as long as the trigger is held down, capable of decoding not
only one single barcode but a concatenation of unique barcodes.
The scanning won't stop until you release the trigger.
Note: (1) A barcode is considered unique when its Code Type or data is different from
others.
(2) Multi-Barcode Mode cannot work with “Multi-Barcode Editor”.
1.7 SCANNING TIMEOUT
Specify the scanning time interval (1~254 sec.; 0= disable) when the scan mode is set
to any of the following –
Laser mode
Auto Off mode
Auto Power Off mode
Aiming mode
1) Read the label above to specify the time interval before the scan engine times.
2) Read the “Decimal Value” label on page 123. For example, read “1” and “5” for the
scanner to automatically shut down after being idle for 15 seconds.
3) Read the “Validate” label on the same page to complete this setting.
Multi-Barcode Mode
Scanner Time-Out after 0~254 seconds (*10)
24
Enter Setup
1600 Series Barcode Scanner User Guide
1.8 DELAY BETWEEN RE-READ
This is also referred to as the “Blocking Time”, which is used to prevent the scanner from
accidentally reading the same barcode twice when the scan mode is set to any of the
following –
Continuous mode
Auto Power Off mode
100 ms
200 ms
800 ms
* 400 ms
2 sec
3 sec
5 sec
1 sec
25
Update
Chapter 1 !Ζ
1.9 EFFECTIVE DECODING AREA
By default, the effective decoding area is 100% covered by the scanned area. However,
you may narrow down the decoding area to prevent reading the wrong barcode when a
number of barcodes are printed closely. The scanner will only read barcodes that appear
in the effective decoding area.
Read the label “Centering On” and specify the percentage to narrow down the decoding
area. For example, read “Left 10%” and then “Right 30%” for the scanner to decode
barcode “A” only.
1.9.1 POSITIONING WINDOW
1.9.2 ADJUSTING WINDOW
PERCENTAGE FOR LEFT HALF
*Left 50%
Centering On
*Centering Off
26
Enter Setup
1600 Series Barcode Scanner User Guide
PERCENTAGE FOR RIGHT HALF
Left 20%
Left 10%
Right 10%
Right 20%
*Right 50%
Right 40%
Right 30%
Left 30%
Left 40%
27
Update
Chapter 1 !Ζ
1.10 NEGATIVE BARCODES
Normally, barcodes are printed with the color of the bars darker than that of the spaces.
But for negative barcodes, they are printed in the opposite sense just like negative films.
The spaces of negative barcodes are printed with a color darker than that of the bars.
You can configure the scanner to be able to read negative barcodes.
1.11 SYMBOLOGIES SUPPORTED
Most of the popular barcode symbologies are supported, as listed below. Each can be
individually enabled or disabled. The scanner will automatically discriminate and
recognize all the symbologies that are enabled. Refer to Chapter 4 Changing Symbology
Settings for details of each symbology.
Codabar*
Industrial 25* Interleaved 25* Matrix 25
Code 39*
Code 93*
Code 128*
EAN-8* EAN-8 Addon 2 & 5
EAN-13* EAN-13 Addon 2 & 5
EAN-128
French Pharmacode
Italian Pharmacode
MSI
Plessey
RSS-14 RSS Expanded RSS
Limited
Telepen
UPC-A* UPC-A Addon 2 & 5
UPC-E* UPC-E Addon 2 & 5
Note: The symbologies, followed by an asterisk mark, are enabled by default.
Enable
*Disable
28
Enter Setup
1600 Series Barcode Scanner User Guide
1.11.1 READ REDUNDANCY FOR ALL SYMBLOGIES
Select the level of reading security. For example,
If "No Redundancy" is selected, one successful decoding will make the reading valid
and induce the "READER Event".
If "Three Times" is selected, it will take a total of four consecutive successful
decodings of the same barcode to make the reading valid. The higher the reading
security is (that is, the more redundancy the user selects), the slower the reading
speed gets.
It is obvious that the more redundancy you select, the higher the reading security is, and
thus, the slower the reading speed becomes. You will have to compromise between
reading security and decoding speed.
1.11.2 ADDON SECURITY FOR UPC/EAN BARCODES
You may like to enforce read redundancy (0~30 times) on UPC/EAN barcodes with
addons only.
Note: UPC/EAN Addon 2 and Addon 5 must be enabled individually for this setting to
take effect.
*No Redundancy
Two Times
One Time
Three Times
Addon Security Level (*0 ~ 30)
29
Update
Chapter 1 !Ζ
1) Read the label above to specify the read redundancy when missing add-ons while
scanning UPC/EAN barcodes. (It is set to 0 by default.)
2) Read the “Decimal Value” label on page 123. For example, read “1” and “2” for the
scanner to re-read the barcode for 12 times.
3) Read the “Validate” label on the same page to complete this setting.
30
Enter Setup
1600 Series Barcode Scanner User Guide
31
Update
In order to establish a proper connection between your computer and the scanner, we
suggest that you follow these instructions –
1) Install batteries and press the [Delete] key for 3 seconds to turn on the scanner.
2) Have the scanner read the “Enter Setup” label to enter the configuration mode.
3) Have the scanner read the associated label to activate the desired interface.
See the following sections for output interfaces supported.
4) Have the scanner read the labels for related settings.
5) Have the scanner read the “Update” label to exit the configuration mode.
Note: By default, the output interface is set to “Bluetooth HID”.
IN THIS CHAPTER
2.1 Bluetooth HID ........................................................... 31
2.2 Bluetooth SPP ........................................................... 38
2.1 BLUETOOTH HID
Refer to Chapter 3 – Setting up Bluetooth Connections for related settings.
Bluetooth HID Settings Defaults
Keyboard Type PCAT (US)
Digits Layout Normal
Capital Lock Type Normal
Capital Lock State Off
Alphabets Transmission Case-sensitive
Digits Transmission Alphanumeric keypad
Inter-Function Delay 0 (ms)
Send “NR” to Host Disable
Chapter 2
SELECTING OUTPUT INTERFACE
32
Enter Setup
1600 Series Barcode Scanner User Guide
2.1.1 ACTIVATE BLUETOOTH HID & SELECT KEYBOARD TYPE
By default, Bluetooth HID is activated on the 1660 scanner, and the keyboard type is set
to PCAT (US). When Bluetooth HID is re-activated, you will have to select a keyboard
type to complete this setting.
1) Read the label above to activate Bluetooth HID and select a keyboard type.
2) Read the “Decimal Value” label on page 123. Refer to the table below for the number
of desired keyboard type.
3) Read the “Validate” label on the same page to complete this setting.
KEYBOARD TYPE
By default, the keyboard type is set to PCAT (US). The following keyboard types are
supported –
No. Keyboard Type No. Keyboard Type
64 PCAT (US) 70 PCAT (UK)
65 PCAT (French) 71 PCAT (Belgium)
66 PCAT (German) 72 PCAT (Spanish)
67 PCAT (Italy) 73 PCAT (Portuguese)
68 PCAT (Swedish) 74 PS55 A01-2 (Japanese)
69 PCAT (Norwegian) 75 User-defined table
2.1.2 RESET CONNECTION
For Bluetooth HID, you can only have one scanner connected to your computer. If you
want to connect the scanner to another computer, you must have it read the “Reset
Connection” label first. The scanner will restart itself automatically. Then, go through the
whole process to establish a new connection.
Activate Bluetooth HID & Select Keyboard Type …
Reset Connection
33
Update
Chapter 2 !Ζ
2.1.3 KEYBOARD SETTINGS
Digits Layout
Capital Lock Type
Capital Lock Setting
Alphabets Transmission
Digits Transmission
Note: Bluetooth HID does not support these functions on PDAs – (1) Capital Lock Setting:
Auto Detection (2) Digits Transmission: Numeric Key
DIGITS LAYOUT
Select a proper layout that matches the alphabets layout. The scanner will make
adjustments according to this setting.
Options Description
Normal Depends on the [Shift] key or [Shift Lock] setting
Lower Row For QWERTY and QWERTZ keyboards
Upper Row For AZERTY keyboards
Note: This setting is to be used with the Character Substitution setting when support to
certain keyboard types (languages) is unavailable but required.
CAPITAL LOCK TYPE & SETTING
In order to send the alphabets with correct case, the scanner needs to know the status of
Caps Lock on the keyboard. Incorrect settings may result in reversed case of the
alphabets being transmitted.
*Normal
Lower Row
Upper Row
34
Enter Setup
1600 Series Barcode Scanner User Guide
Cap Lock Type Description
Normal Normal type
Capital Lock When enabled, the keys of alphabetic characters will be interpreted as
capital letters. However, this does not affect the number or punctuation
keys.
Shift Lock When enabled, the keys of alphabetic characters will be interpreted as
capital letters. In addition, this affects the number or punctuation keys.
Capital Lock State Description
Capital Lock OFF Assuming that the status of Caps Lock on the keyboard is OFF, transmitted
characters are exactly the same as in the barcode (when "case-sensitive" is
selected for Alphabets Transmission).
Capital Lock ON Assuming that the status of Caps Lock on the keyboard is ON, transmitted
characters are exactly the same as in the barcode (when "case-sensitive" is
selected for Alphabets Transmission).
Refer to the Capital Lock Type above.
Auto Detection The scanner will automatically detect the status of Caps Lock on the
keyboard before data is transmitted; transmitted characters are exactly the
same as in the barcode (when "case-sensitive" is selected for Alphabets
Transmission).
This setting is not supported on PDAs.
*Capital Lock OFF
Capital Lock
Shift Lock
*Normal
35
Update
Chapter 2 !Ζ
ALPHABETS TRANSMISSION
By default, the alphabets transmission is case-sensitive, meaning that the alphabets will
be transmitted according to their original case, the status of Caps Lock on the keyboard,
as well as the Capital Lock setting. Select [Ignore Case] to have alphabets transmitted
according to the status of Caps Lock on the keyboard only.
Auto Detection
Capital Lock ON
36
Enter Setup
1600 Series Barcode Scanner User Guide
DIGITS TRANSMISSION
By default, the alphanumeric keypad is used for transmitting digits. Select “Numeric
Keypad” if you wish to use the keys on the numeric keypad.
Note: If you select “Numeric Keypad”, the Num Lock status of the physical keyboard
should be "ON". This setting is not supported on PDAs.
2.1.4 INTER-FUNCTION DELAY
By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 255,
to match the computer response time of the keyboard interface. Such delay time is
inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the
delay time is, the slower the transmission speed will be.
*Alphanumeric Key
Numeric Key
Ignore Case
*Case-sensitive
37
Update
Chapter 2 !Ζ
Value Delay Time Value Delay Time
0 Disable 195 ~ 204 200 millisecond
1 ~ 14 10 millisecond 205 ~ 214 210 millisecond
15 ~ 24 20 millisecond 215 ~ 224 220 millisecond
25 ~ 34 30 millisecond 225 ~ 234 230 millisecond
35 ~ 44 40 millisecond 235 ~ 244 240 millisecond
45 ~ 54 50 millisecond 245 ~ 254 250 millisecond
… … 255 260 millisecond
1) Read the label above to specify the inter-function delay.
2) Read the “Decimal Value” label on page 123 for the desired inter-function delay
(millisecond).
3) Read the “Validate” label on the same page to complete this setting.
Inter-Function Delay … (*0 ~ 255)
38
Enter Setup
1600 Series Barcode Scanner User Guide
2.2 BLUETOOTH SPP
Refer to Chapter 3 – Setting up Bluetooth Connections for related settings.
2.2.1 ACTIVATE BLUETOOTH SPP
2.2.2 INTER-FUNCTION DELAY
By default, the inter-function delay is set to zero. Specify a value, ranging from 0 to 255,
to match the computer response time of the keyboard interface. Such delay time is
inserted between every function code (0x01 ~ 0x1F) being transmitted. The longer the
delay time is, the slower the transmission speed will be.
Value Delay Time Value Delay Time
0 Disable 195 ~ 204 200 millisecond
1 ~ 14 10 millisecond 205 ~ 214 210 millisecond
15 ~ 24 20 millisecond 215 ~ 224 220 millisecond
25 ~ 34 30 millisecond 225 ~ 234 230 millisecond
35 ~ 44 40 millisecond 235 ~ 244 240 millisecond
45 ~ 54 50 millisecond 245 ~ 254 250 millisecond
… … 255 260 millisecond
1) Read the label above to specify the inter-function delay.
2) Read the “Decimal Value” label on page 123 for the desired inter-function delay
(millisecond).
3) Read the “Validate” label on the same page to complete this setting.
Activate Bluetooth SPP
Inter-Function Delay … (*0 ~ 255)
39
Update
Chapter 2 !Ζ
2.2.3 ACK/NAK TIMEOUT
By default, the scanner sends data to the host without waiting for an ACK/NAK response
before sending more data. Specify a value, ranging from 1 to 99 in units of 0.1 second. If
no response within the specified period of time, the scanner will attempt to send the
same data three more times. If all the attempts fail without any notification, data loss
will occur.
1) Read the label above to specify the time interval for the scanner to send data and
wait for a response from the host.
2) Read the “Decimal Value” label on page 123. For example, read “1” and “0” for the
scanner to automatically shut down after being idle for 1 second.
3) Read the “Validate” label on the same page to complete this setting.
ACK/NAK ERROR BEEP
Note: We suggest you to enable the error beep so that you will be notified of such data
loss and have the scanner re-read data.
ACK/NAK Time-Out after … (*0 ~ 99)
Enable Error Beep
*Disable Error Beep
40
Enter Setup
1600 Series Barcode Scanner User Guide
41
Update
The Bluetooth scanner can be configured to send data to a computer via a Bluetooth
dongle, or directly to a Bluetooth-enabled PDA or laptop. Upon powering up, the 1660
scanner will be ready for establishing a Bluetooth connection with a Bluetooth dongle.
Below is the procedure to configure the 1660 scanner before establishing a Bluetooth
connection.
1) Have the scanner read the “Enter Setup” label to enter the configuration mode.
2) Have the scanner read the desired Bluetooth interface label – “Activate Bluetooth
SPP” or “Activate Bluetooth HID & Select Keyboard Type”.
It supports PCAT – US, French, German, Italian, Swedish, Norwegian, UK, Belgium,
Spanish, Portuguese, and PS55 A01-2 – Japanese.
3) Have the scanner read the labels related to Bluetooth settings, such as Device Name
Broadcasting, Authentication & PIN Code, etc.
4) Have the scanner read the “Update” label to exit the configuration mode.
Once connected, be aware of the following notifications during operation –
When getting out of range or powering off the cradle, the scanner will respond with
two short beeps (high-low tone) and its LED indicator will become blue, flashing
quickly.
The power-saving feature of the scanner will automatically shut down the scanner
and stop a Bluetooth connection when it is idle for a specific period of time. The
scanner will respond with three beeps (tone descending from high to low) and its LED
indicator will become off.
IN THIS CHAPTER
3.1 Configuring Bluetooth Settings..................................... 42
3.2 Connecting via Bluetooth Dongle.................................. 44
Chapter 3
SETTING UP BLUETOOTH CONNECTIONS
42
Enter Setup
1600 Series Barcode Scanner User Guide
3.1 CONFIGURING BLUETOOTH SETTINGS
3.1.1 SNIFF MODE (POWER-SAVING)
This is Bluetooth standard power-saving feature, also known as Sniff mode. When
enabled, the scanner will listen to the piconet at a reduced rate.
Note: By default, power-saving is enabled. When connecting more than two 1660
scanners via the Bluetooth dongle, we suggest you to disable the power-saving
setting for a more reliable connection.
3.1.2 DEVICE NAME BROADCASTING
The scanner can be configured to hide itself from other Bluetooth devices. Simply disable
the device name broadcasting setting so that it won’t be discovered by any other
computer or PDA. However, broadcasting must be enabled for establishing an initial
connection with the scanner. For example, you can disable device name broadcasting
after successfully connecting the scanner to WorkStation1. Such connection will be
maintained automatically unless the scanner is removed from the paired device list
(called unpairing) by WorkStation1 or any changes made to authentication and the PIN
code. If you want WorkStation2 to connect to the scanner, you will have to enable device
name broadcasting first.
Note: By default, device name broadcasting is enabled (which is required for initial
connection).
*Enable
Disable
*Enable
Disable
43
Update
Chapter 3 !Ζ
3.1.3 AUTHENTICATION
For security concerns, it is suggested that you enable authentication and specify a unique
PIN code, also known as the passkey used to pair two Bluetooth devices. The scanner
itself allows up to 16 characters for a PIN code. This means you will have to enter exactly
the same string for your computer or PDA to connect to the scanner. If the passkey is
incorrect, any connection attempt will be turned down by the scanner. When any changes
are made to authentication and PIN code on the scanner side, you will have to remove
the scanner from the paired device list (called unpairing) and go through the whole
process to re-establish the connection.
ENTERING PIN CODE
By default, the Bluetooth PIN code is set to “0000”. Maximum 16 characters are allowed.
Note: When using Bluetooth HID, some driver of Bluetooth dongle may not support
pre-defined PIN code for authentication. In this case, make sure you disable
authentication before pairing. The host PIN code will be displayed on the computer
screen. Have the scanner read the setup barcode “Enter PIN Code in Decimal” to
input the matching PIN code quickly.
1) Read one of the labels above to specify the PIN code, in decimal or hexadecimal.
2) Read the “Decimal Value” label on page 123 or the “Hexadecimal Value” label on page
124 for the desired digits or character string.
3) Read the “Validate” label on the same page to complete this setting.
Yes
Enter PIN Code in Hexadecimal …
Enter PIN Code in Decimal …
*No
44
Enter Setup
1600 Series Barcode Scanner User Guide
3.2 CONNECTING VIA BLUETOOTH DONGLE
This is called "pairing with a Bluetooth device". The procedure for connecting the scanner
to a computer via a Bluetooth dongle is pretty much the same except for the software
you are using.
Note: When connecting more than two Bluetooth scanners to a computer via the
Bluetooth dongle, we suggest you to disable “Sniff Mode” for a more reliable
connection.
If your computer is running Microsoft Windows XP Service Pack 2 (SP2) or Windows Vista,
you can use the generic software support that Windows includes, or you can use the
driver that the device manufacturer provides.
Now, let’s try using the generic software support that Windows XP Service Pack 2
includes.
3.2.1 BLUETOOTH HID – ADD BLUETOOTH DEVICE WIZARD
By default, Bluetooth HID is activated on the 1660 scanner, and the keyboard type is set
to PCAT (US). When Bluetooth HID is re-activated, you will have to select a keyboard
type to complete this setting.
The procedure is the same as for Bluetooth SPP. Refer to steps 1~11 below.
3.2.2 BLUETOOTH SPP – ADD BLUETOOTH DEVICE WIZARD
1) Connect a Bluetooth dongle to your computer, running Windows XP SP2.
2) Double-click the Bluetooth icon fro the lower right of the taskbar.
Alternatively, you may go to Control Panel > Bluetooth Devices.
3) Click [Add] to search Bluetooth devices nearby.
4) Select the check box of [My device is set up and ready to be found] when the
Bluetooth scanner is ready – having battery inserted or USB cable connected,
Bluetooth settings such as select Bluetooth SPP or Bluetooth HID, broadcasting
enabled, authentication enabled, and PIN code specified, etc.
5) Click [Next].
6) Wait for a few seconds for the Wizard to search available Bluetooth devices nearby.
The scanner will appear with its “serial number” as the device name. You may
double-check the “Serial Number” label on the scanner to ensure connecting with the
correct scanner. Select the target scanner. If the target scanner does not appear on
the list, click [Search Again] to refresh the list. The scanner might enter Suspend
Mode now, and you can press the trigger to have it active again (=discoverable). It
will then stay active for one minute and wait for PC to establish a connection.
7) Click [Next].
2
45
Update
Chapter 3 !Ζ
6
7
3
4
5
46
Enter Setup
1600 Series Barcode Scanner User Guide
8) Enter the passkey for authentication, which must be exactly the same as configured
for the scanner.
9) Click [Next].
Wait for a few seconds for Windows to exchange passkeys.
10) Click [Finish].
8
9
Ignore this
47
Update
Chapter 3 !Ζ
11) Now the target scanner will be listed as shown below.
For Bluetooth SPP, you can have up to seven scanners connected to your computer.
It is possible for another computer to connect to one these scanners as long as it is in
Suspend Mode and the authentication and PIN code settings are matching.
10
Bluetooth SPP Only
48
Enter Setup
1600 Series Barcode Scanner User Guide
Note: When any changes are made to authentication and PIN code on the scanner side,
or you want to change to use Bluetooth HID, it is suggested that you remove the
scanner from the paired device list (called unpairing) and go through the whole
process to re-establish the connection.
12) Run the desired application, such as HyperTerminal, on your computer.
The status of the scanner listed on the device list will be updated to “Connected”,
indicating the Bluetooth connection is established successfully via the outgoing COM
port.
Se
l
ect a
n
d
R
e
m
o
v
e
49
Update
Chapter 3 !Ζ
Bluetooth Connected
Bluetooth Disconnected
50
Enter Setup
1600 Series Barcode Scanner User Guide
51
Update
In this chapter, a brief on the symbology settings is provided for your reference.
IN THIS CHAPTER
4.1 Codabar ................................................................... 52
4.2 Code 25 - Industrial 25............................................... 54
4.3 Code 25 - Interleaved 25 ............................................ 57
4.4 Code 25 - Matrix 25 ................................................... 60
4.5 Code 39 ................................................................... 63
4.6 Code 93 ................................................................... 65
4.7 Code 128.................................................................. 65
4.8 EAN-8 ...................................................................... 66
4.9 EAN-13 .................................................................... 68
4.10 EAN-128................................................................. 70
4.11 ISBT 128 ................................................................ 71
4.12 MSI........................................................................ 72
4.13 French Pharmacode.................................................. 75
4.14 Italian Pharmacode .................................................. 76
4.15 Plessey................................................................... 77
4.16 RSS Family ............................................................. 78
4.17 Telepen .................................................................. 82
4.18 UPC-A .................................................................... 83
4.19 UPC-E .................................................................... 85
Chapter 4
CHANGING SYMBOLOGY SETTINGS
52
Enter Setup
1600 Series Barcode Scanner User Guide
4.1 CODABAR
4.1.1 START/STOP CHARACTERS SELECTION
Select one of the four different start/stop character pairs –
4.1.2 START/STOP TRANSMISSION
Decide whether or not to include the start/stop characters in the data being transmitted.
*Enable Codabar
Disable Codabar
* abcd/abcd
abcd/tn*e
ABCD/ABCD
ABCD/TN*E
Transmit Codabar
Start/Stop Characters
53
Update
Chapter 4 !Ζ
4.1.3 CLSI CONVERSION
When enabled, the CLSI editing strips the start/stop characters and inserts a space after
the first, fifth, and tenth characters of a 14-character Codabar barcode.
Note: The 14-character barcode length does not include start/stop characters.
*Do Not Transmit
Apply CLSI Editing
*Do Not Apply
54
Enter Setup
1600 Series Barcode Scanner User Guide
4.2 CODE 25 – INDUSTRIAL 25
4.2.1 START/STOP PATTERN SELECTION
This decides the readability of all 2 of 5 symbology variants. For example, flight tickets
actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In
order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5
should set to "Interleaved 25".
4.2.2 CHECKSUM VERIFICATION
Decide whether to verify the checksum. If the checksum is incorrect, the barcode will not
be accepted.
*Enable Industrial 25
Disable Industrial 25
*Industrial 25
Start/Stop Pattern
Matrix 25
Start/Stop Pattern
Interleaved 25
Start/Stop Pattern
Verify Industrial 25
Checksum
55
Update
Chapter 4 !Ζ
4.2.3 CHECKSUM TRANSMISSION
Decide whether to include the checksum in the data being transmitted.
4.2.4 CODE LENGTH QUALIFICATION
Because of the weak structure of the 2 of 5 symbologies, it is possible to make a "short
scan" error. To prevent the "short scan" error, define the "Length Qualification" settings
to ensure that the correct barcode is read by qualifying the allowable code length.
If "Max/Min Length" is selected, the maximum length and the minimum length must
be specified. It only accepts those barcodes with lengths that fall between max/min
lengths specified.
If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
1) Read the label to enable either Max. /Min. length qualification or fixed length
qualification.
*Transmit Industrial
25 Checksum
Do Not Transmit
*Do Not Verify
*Enable Max./Min.
Length (0 ~ 127) …
Enable Fixed Length(s) …
56
Enter Setup
1600 Series Barcode Scanner User Guide
2) Read the labels for Max. /Min or fixed length separately.
3) Read the “Decimal Value” label on page 123 for the desired length.
4) Read the “Validate” label on the same page to complete this setting.
Max. Length (*127)
Or Fixed Length 1
Min. Length (*4)
Or Fixed Length 2
57
Update
Chapter 4 !Ζ
4.3 CODE 25 – INTERLEAVED 25
4.3.1 START/STOP PATTERN SELECTION
This decides the readability of all 2 of 5 symbology variants. For example, flight tickets
actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In
order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5
should set to "Interleaved 25".
4.3.2 CHECKSUM VERIFICATION
Decide whether to verify the checksum. If the checksum is incorrect, the barcode will not
be accepted.
*Enable Interleaved 25
Disable Interleaved 25
Industrial 25
Start/Stop Pattern
Matrix 25
Start/Stop Pattern
*Interleaved 25
Start/Stop Pattern
Verify Interleaved 25
Checksum
58
Enter Setup
1600 Series Barcode Scanner User Guide
4.3.3 CHECKSUM TRANSMISSION
Decide whether to include the checksum in the data being transmitted.
4.3.4 CODE LENGTH QUALIFICATION
Because of the weak structure of the 2 of 5 symbologies, it is possible to make a "short
scan" error. To prevent the "short scan" error, define the "Length Qualification" settings
to ensure that the correct barcode is read by qualifying the allowable code length.
If "Max/Min Length" is selected, the maximum length and the minimum length must
be specified. It only accepts those barcodes with lengths that fall between max/min
lengths specified.
If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
1) Read the label to enable either Max. /Min. length qualification or fixed length
qualification.
*Enable Max./Min.
Length (0 ~ 127) …
*Transmit Interleaved
25 Checksum
D
o Not Transmit
*
Do Not Verify
59
Update
Chapter 4 !Ζ
2) Read the labels for Max. /Min or fixed length separately.
3) Read the “Decimal Value” label on page 123 for the desired length.
4) Read the “Validate” label on the same page to complete this setting.
Enable Fixed Length(s) …
Max. Length (*126)
Or Fixed Length 1
Min. Length (*4)
Or Fixed Length 2
60
Enter Setup
1600 Series Barcode Scanner User Guide
4.4 CODE 25 – MATRIX 25
4.4.1 START/STOP PATTERN SELECTION
This decides the readability of all 2 of 5 symbology variants. For example, flight tickets
actually use an Industrial 2 of 5 barcode but with Interleaved 2 of 5 start/stop pattern. In
order to read this barcode, the start/stop pattern selection parameter of Industrial 2 of 5
should set to "Interleaved 25".
4.4.2 CHECKSUM VERIFICATION
Decide whether to verify the checksum. If the checksum is incorrect, the barcode will not
be accepted.
Enable Matrix 25
*Disable Matrix 25
Industrial 25
Start/Stop Pattern
*Matrix 25
Start/Stop Pattern
Interleaved 25
Start/Stop Pattern
Verify Matrix 25
Checksum
61
Update
Chapter 4 !Ζ
4.4.3 CHECKSUM TRANSMISSION
Decide whether to include the checksum in the data being transmitted.
4.4.4 CODE LENGTH QUALIFICATION
Because of the weak structure of the 2 of 5 symbologies, it is possible to make a "short
scan" error. To prevent the "short scan" error, define the "Length Qualification" settings
to ensure that the correct barcode is read by qualifying the allowable code length.
If "Max/Min Length" is selected, the maximum length and the minimum length must
be specified. It only accepts those barcodes with lengths that fall between max/min
lengths specified.
If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
1) Read the label to enable either Max. /Min. length qualification or fixed length
qualification.
*Enable Max./Min.
Length (0 ~ 127) …
*Transmit Matrix 25
Checksum
Do Not Transmit
*Do Not Verify
62
Enter Setup
1600 Series Barcode Scanner User Guide
2) Read the labels for Max. /Min or fixed length separately.
3) Read the “Decimal Value” label on page 123 for the desired length.
4) Read the “Validate” label on the same page to complete this setting.
Enable Fixed Length(s) …
Min. Length (*4)
Or Fixed Length 2
Max. Length (*127)
Or Fixed Length 1
63
Update
Chapter 4 !Ζ
4.5 CODE 39
4.5.1 START/STOP TRANSMISSION
Decide whether or not to include the start/stop characters in the data being transmitted.
4.5.2 CHECKSUM VERIFICATION
Decide whether or not to perform checksum verification when decoding barcodes.
If enabled and the checksum found incorrect, the barcode will not be accepted.
*Enable Code 39
Disable Code 39
Transmit Code 39
Start/Stop Characters
*Do Not Transmit
Verify Code 39
Checksum
*Do Not Verify
64
Enter Setup
1600 Series Barcode Scanner User Guide
4.5.3 CHECKSUM TRANSMISSION
Decide whether or not to include the checksum character in the data being transmitted.
4.5.4 STANDARD/FULL ASCII CODE 39
Decide whether or not to support Code 39 Full ASCII that includes all the alphanumeric
and special characters.
Code 39 Full ASCII
*
Standard Code 39
*Transmit Code 39
Checksum
Do Not Transmit
65
Update
Chapter 4 !Ζ
4.6 CODE 93
You can only configure the scanner to read this symbology or not.
4.7 CODE 128
You can only configure the scanner to read this symbology or not.
*Enable Code 93
Disable Code 93
*Enable Code 128
Disable Code 128
66
Enter Setup
1600 Series Barcode Scanner User Guide
4.8 EAN-8
4.8.1 CONVERT TO EAN-13
Decide whether or not to expand the read EAN-8 barcode into EAN-13.
If enabled, the next processing will follow the parameters configured for EAN-13.
*Enable EAN-8
(No Addon)
Disable EAN-8
(No Addon)
*Disable EAN-8
Addon 2
*Disable EAN-8
Addon 5
Enable EAN-8
Addon 2
Enable EAN-8
Addon 5
Convert EAN-8
to EAN-13
67
Update
Chapter 4 !Ζ
4.8.2 CHECKSUM TRANSMISSION
Decide whether or not to include the checksum character in the data being transmitted.
*Transmit EAN-8
Checksum
Do Not Transmit
*Do Not Convert
68
Enter Setup
1600 Series Barcode Scanner User Guide
4.9 EAN-13
4.9.1 ISBN CONVERSION
Decide whether or not to convert the EAN-13 barcode, starting with 978 and 979, to
ISBN.
Disable EAN-13
(No Addon)
*Disable EAN-13
Addon 2
*Disable EAN-13
Addon 5
Enable EAN-13
Addon 2
Enable EAN-13
Addon 5
*Enable EAN-13
(No Addon)
Convert EAN-13 to ISBN
69
Update
Chapter 4 !Ζ
4.9.2 ISSN CONVERSION
Decide whether or not to convert the EAN-13 barcode, starting with 977 to ISSN.
4.9.3 CHECKSUM TRANSMISSION
Decide whether or not to include the checksum character in the data being transmitted.
*Do Not Convert
*Do Not Convert
Convert EAN-13 to ISSN
Do Not Transmit
*Transmit EAN-13
Checksum
70
Enter Setup
1600 Series Barcode Scanner User Guide
4.10 EAN-128
4.10.1 CODE ID TRANSMISSION
Decide whether or not to include the Code ID (“]C1”) in the data being transmitted.
4.10.2 FIELD SEPARATOR (GS CHARACTER)
Decide whether or not to apply a field separator (to convert the FNC1 control character to
human readable character).
1) Read the label above to enable field separator.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string.
3) Read the “Validate” label on the same page to complete this setting.
Enable EAN-128
*Disable EAN-128
Transmit EAN-128
Code ID
*
Do Not Transmit
Enable Field Separator …
71
Update
Chapter 4 !Ζ
Note: EAN-128 barcodes start with the FNC1 control character to distinguish themselves
from other uses of Code 128. FNC1 is also used to separate data fields in the
EAN-128 barcodes.
4.11 ISBT 128
You can only configure the scanner to read this symbology or not.
Enable ISBT 128
*Disable ISBT 128
72
Enter Setup
1600 Series Barcode Scanner User Guide
4.12 MSI
4.12.1 CHECKSUM VERIFICATION
Select one of the three checksum calculations to perform checksum verification when
decoding barcodes.
If enabled and the checksum found incorrect, the barcode will not be accepted.
4.12.2 CHECKSUM TRANSMISSION
Decide whether or not to include the checksum character in the data being transmitted.
Enable MSI
*Disable MSI
*Single Modulo 10
D
ouble Modulo 10
Modulo 10 & 11
*Last Digit Not
Transmitted
73
Update
Chapter 4 !Ζ
4.12.3 CODE LENGTH QUALIFICATION
Because of the weak structure of the symbology, it is possible to make a "short scan" error. To
prevent the "short scan" error, define the "Length Qualification" settings to ensure that the correct
barcode is read by qualifying the allowable code length.
If "Max/Min Length" is selected, the maximum length and the minimum length must
be specified. It only accepts those barcodes with lengths that fall between max/min
lengths specified.
If “Fixed Length” is selected, up to 2 fixed lengths can be specified.
1) Read the label to enable either Max. /Min. length qualification or fixed length
qualification.
2) Read the labels for Max. /Min or fixed length separately.
Both Digits Not
Transmitted
Both Digits
Transmitted
Enable Fixed Length(s) …
*Enable Max./Min.
Length (0 ~ 127) …
Min. Length (*4)
Or Fixed Length 2
Max. Length (*127)
Or Fixed Length 1
74
Enter Setup
1600 Series Barcode Scanner User Guide
3) Read the “Decimal Value” label on page 123 for the desired length.
4) Read the “Validate” label on the same page to complete this setting.
75
Update
Chapter 4 !Ζ
4.13 FRENCH PHARMACODE
4.13.1 CHECKSUM TRANSMISSION
Decide whether or not to include the checksum character in the data being transmitted.
Enable French Pharmacode
*Disable French
Pharmacode
*Transmit French
Pharmacode Checksum
Do Not Transmit
76
Enter Setup
1600 Series Barcode Scanner User Guide
4.14 ITALIAN PHARMACODE
4.14.1 CHECKSUM TRANSMISSION
Decide whether or not to include the checksum character in the data being transmitted.
Enable Italian Pharmacode
*Disable Italian
Pharmacode
*Transmit Italian
Pharmacode Checksum
Do Not Transmit
77
Update
Chapter 4 !Ζ
4.15 PLESSEY
4.15.1 CONVERT TO UK PLESSEY
Decide whether or not to change each occurrence of the character 'A' to character 'X' in
the decoded data.
4.15.2 CHECKSUM TRANSMISSION
Decide whether or not to include the checksum characters (two digits) in the data being
transmitted.
Enable Plessey
*Disable Plessey
Convert to UK Plessey
*Do Not Convert
*Transmit Plessey
Checksum
Do Not Transmit
78
Enter Setup
1600 Series Barcode Scanner User Guide
4.16 RSS FAMILY
4.16.1 CODE ID SELECTION
Select a desired Code ID to use – RSS Code ID “]e0“ or EAN-128 Code ID “]C1”.
4.16.2 RSS-14
CODE ID TRANSMISSION
Decide whether or not to include the Code ID in the data being transmitted.
Enable RSS-14 &
RSS Expanded
*Disable RSS-14 &
RSS Expanded
“]C1” for RSS Code ID
“]e0” for RSS Code ID
(Default)
*Transmit RSS-14 Code ID
Do Not Transmit
79
Update
Chapter 4 !Ζ
APPLICATION ID TRANSMISSION
Decide whether or not to include the Application ID ("01") in the data being transmitted.
CHECKSUM TRANSMISSION
Decide whether or not to include the check digit in the data being transmitted.
4.16.3 RSS EXPANDED
CODE ID TRANSMISSION
Decide whether or not to include the Code ID in the data being transmitted.
Enable RSS-14 &
RSS Expanded
*Disable RSS-14 &
RSS Expanded
*Transmit RSS-14
Checksum
Do Not Transmit
*Transmit RSS-14
Application ID
Do Not Transmit
80
Enter Setup
1600 Series Barcode Scanner User Guide
4.16.4 RSS LIMITED
CODE ID TRANSMISSION
Decide whether or not to include the Code ID in the data being transmitted.
APPLICATION ID TRANSMISSION
Decide whether or not to include the Application ID ("01") in the data being transmitted.
Enable RSS Limited
*Disable RSS Limited
*Transmit RSS
Limited Code ID
Do Not Transmit
*Transmit RSS
Expanded Code ID
Do Not Transmit
81
Update
Chapter 4 !Ζ
CHECKSUM TRANSMISSION
Decide whether or not to include the check digit in the data being transmitted.
*Transmit RSS
Limited Checksum
Do Not Transmit
*Transmit RSS Limited
Application ID
Do Not Transmit
82
Enter Setup
1600 Series Barcode Scanner User Guide
4.17 TELEPEN
4.17.1 TELEPEN OUTPUT – FULL ASCII/NUMERIC
Decide whether or not to support Telepen in full ASCII code. By default, it supports ASCII mode.
AIM Telepen (Full ASCII) includes all the alphanumeric and special characters.
Enable Telepen
*Disable Telepen
Original Telepen
(Numeric)
* AIM Telepen
83
Update
Chapter 4 !Ζ
4.18 UPC-A
4.18.1 CONVERT TO EAN-13
Decide whether or not to expand the read UPC-A barcode into EAN-13.
If enabled, the next processing will follow the parameters configured for EAN-13.
Disable UPC-A
(No Addon)
*Disable UPC-A
Addon 2
*Disable UPC-A
Addon 5
Enable UPC-A
Addon 2
Enable UPC-A
Addon 5
*Enable UPC-A
(No Addon)
Convert UPC-A
to EAN-13
84
Enter Setup
1600 Series Barcode Scanner User Guide
4.18.2 SYSTEM NUMBER TRANSMISSION
Decide whether or not to include the system number in the data being transmitted.
4.18.3 CHECKSUM TRANSMISSION
Decide whether or not to include the checksum character in the data being transmitted.
*Do Not Convert
Do Not Transmit
*Transmit UPC-A
Checksum
Do Not Transmit
*Transmit UPC-A
System Number
85
Update
Chapter 4 !Ζ
4.19 UPC-E
4.19.1 SYSTEM NUMBER SELECTION
Decide whether to decode the ordinary UPC-E barcodes only or both UPC-E0 and UPC-E1 barcodes.
System number 0 enabled for decoding UPC-E0 barcodes.
System number 1 enabled for decoding UPC-E1 barcodes.
Disable UPC-E
(No Addon)
*Disable UPC-E
Addon 2
*Disable UPC-E
Addon 5
Enable UPC-E
Addon 2
Enable UPC-E
Addon 5
*Enable UPC-E
(No Addon)
System Number 0 & 1
86
Enter Setup
1600 Series Barcode Scanner User Guide
Warning: Because of the way system number 1 is encoded, if both system numbers
are enabled, the user might suffer from short scanning UPC-A or EAN-13
barcodes into UPC-E1 barcodes.
4.19.2 CONVERT TO UPC-A
Decide whether or not to expand the read UPC-E barcode into UPC-A.
If enable, the next processing will follow the parameters configured for UPC-A.
4.19.3 SYSTEM NUMBER TRANSMISSION
Decide whether or not to include the system number in the data being transmitted.
4.19.4 CHECKSUM TRANSMISSION
Decide whether or not to include the checksum character in the data being transmitted.
Convert UPC-E
to UPC-A
*Do Not Convert
*Do Not Transmit
Transmit UPC-E
System Number
* System Number 0
Only
87
Update
Chapter 4 !Ζ
Do Not Transmit
*Transmit UPC-E
Checksum
88
Enter Setup
1600 Series Barcode Scanner User Guide
89
Update
You may configure in which format the collected data will be output to the host computer.
Barcode read by the scanner will be processed in the following sequence –
1) Perform character substitution on the data scanned.
2) Add Code ID and Length Code to the front of the data: [Code ID][Length Code][Data]
3) Process the whole data in step 2 with user formats. Data is now divided into fields by
user specified rules.
4) Add Prefix Code and Suffix Code before transmission: [Prefix Code][Processed
Data][Suffix Code]
IN THIS CHAPTER
5.1 Letter Case ............................................................... 89
5.2 Character Substitution................................................ 90
5.3 Prefix/Suffix Code ...................................................... 96
5.4 Code ID.................................................................... 97
5.5 Length Code ............................................................101
5.6 Multi-Barcode Editor..................................................104
5.1 LETTER CASE
By default, the alphabets transmission is case-sensitive, meaning that the alphabets will
be transmitted according to their original case. Ignoring the original letter case, select
[Upper Case] to output data in upper case only; otherwise, select [Lower Case] to output
data in lower case only.
Chapter 5
DEFINING OUTPUT FORMAT
*Normal
Upper Case
Lower Case
90
Enter Setup
1600 Series Barcode Scanner User Guide
5.2 CHARACTER SUBSTITUTION
Character substitution is performed on every occurrence of the first character specified. If
only one character is specified, every occurrence of that character in the barcode will be
taken away.
The first character will be replaced by the second character(s).
Up to three sets of character substitution can be configured.
Note: The character substitution is performed only on the barcode itself and before the
processing of editing formats. It is not applicable to the Prefix/Suffix Code, Code
ID, Length Code, or any Additional Field.
5.2.1 SELECT A SET FOR CHARACTER SUBSTITUION
1) Read the label above to enable character substitution by set.
For example, have the scanner read the “Set 1” label to configure the first set of
character substitution. The scanner will respond with one short beep, high tone, to
indicate more setup labels are required.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string.
For example, have the scanner read (1) “3”, “0”, “2” and “D” to replace the character
[0] with a dash [-] for Set 1, and (2) “3”, “0”, “2”, “D”, “3” and “0”to replace the
character [0] with a dash [- 0] for Set 2.
3) Read the “Validate” label on the same page to complete this setting. (The defined set
or sets will be applied to all symbologies by default.)
Configure Set 1
Configure Set 2
Configure Set 3
91
Update
Chapter 5 !Ζ
5.2.2 SYMBOLOGIES FOR CHARACTER SUBSTITUTION (ALL 3 SETS)
By default character substitution will be performed on all symbologies. If the character
substitution is not desired with one or more symbologies, read the “Ignore” label for each
undesired symbologies and all the three sets will not be applied to them.
CODABAR
CODE 39
CODE 93
CODE 128
EAN-128
*Apply to Codabar Do Not Apply
*Apply to Code 39 Do Not Apply
*Apply to Code 93 Do Not Apply
*Apply to Code 128
*Apply to EAN-128 Do Not Apply
Do Not Apply
92
Enter Setup
1600 Series Barcode Scanner User Guide
EAN-8 (NO ADDON)
EAN-8 ADDON 2
EAN-8 ADDON 5
EAN-13 (NO ADDON)
EAN-13 ADDON 2
EAN-13 ADDON 5
*Apply to EAN-8 Do Not Apply
*Apply to EAN-8
Addon 2
*Apply to EAN-8
Addon 5
*Apply to EAN-13
*Apply to EAN-13
Addon 2
Do Not Apply
*Apply to EAN-13
Addon 5
Do Not Apply
Do Not Apply
Do Not Apply
Do Not Apply
93
Update
Chapter 5 !Ζ
FRENCH PHARMACODE
ITALIAN PHARMACODE
INDUSTRIAL 25
INTERLEAVED 25
MATRIX 25
MSI
*Apply to French
Pharmacode Do Not Apply
*Apply to Italian
Pharmacode Do Not Apply
*Apply to
Industrial 25
*Apply to
Interleaved 25
*Apply to Matrix 25 Do Not Apply
*Apply to MSI
Do Not Apply
Do Not Apply
Do Not Apply
94
Enter Setup
1600 Series Barcode Scanner User Guide
PLESSEY
RSS FAMILY
TELEPEN
UPC-A (NO ADDON)
UPC-A ADDON 2
UPC-A ADDON 5
*Apply to Plessey
*Apply to RSS Family
*Apply to Telepen
*Apply to UPC-A
*Apply to UPC-A
Addon 2
*Apply to UPC-A
Addon 5
Do Not Apply
Do Not Apply
Do Not Apply
Do Not Apply
Do Not Apply
Do Not Apply
95
Update
Chapter 5 !Ζ
UPC-E (NO ADDON)
UPC-E ADDON 2
UPC-E ADDON 5
*Apply to UPC-E Do Not Apply
*Apply to UPC-E
Addon 2
*Apply to UPC-E
Addon 5
Do Not Apply
Do Not Apply
96
Enter Setup
1600 Series Barcode Scanner User Guide
5.3 PREFIX/SUFFIX CODE
By default, there is no prefix code, and [ENTER] or [CR] (Carriage Return) is configured
to be suffix code. Up to 8 characters can be configured, for example, “Barcode_”, and
you will have the string appear in front of the barcode read, like this –
“Barcode_1234567890”.
If “Keyboard Wedge” is configured for interface, Key Type and Key Status will then
become applicable. You may decide whether or not to apply Key Status when “Normal
Key” is selected for Key Type.
Key Type Key Status
Scan Code Up to 4 scan code values are allowed –
each requires two hexadecimal values.
N/A
Normal Key Up to 8 character strings are allowed –
each requires two hexadecimal values.
Default setting
Add Shift
Add Left Ctrl
Add Left Alt
Add Right Ctrl
Add Right Alt
Add Break
For example, read labels for [Add Shift],
[A], [Add Shift], and [B].
1) Read the label above to apply prefix code or suffix code separately. (Max. 8
characters each)
2) Read the “Hexadecimal Value” label on page 124 for the desired character string. For
example, read “2” and “B” for the scanner to prefix or suffix the character [+].
3) Read the “Validate” label on the same page to complete this setting.
Configure Prefix
C
onfigure Suffix
97
Update
Chapter 5 !Ζ
5.4 CODE ID
Up to two characters for Code ID can be configured for each symbology. To make the
Code ID configuration easier, the scanner provides five pre-defined Code ID sets that you
can select one and make necessary changes on it.
If "Keyboard Wedge" is configured for interface, Key Type and Key Status will then
become applicable. You may decide whether or not to apply Key Status when “Normal
Key” is selected for Key Type.
Key Type Key Status
Scan Code Up to 1 scan code values are allowed –
each requires two hexadecimal values.
N/A
Normal Key Up to 2 character strings are allowed –
each requires two hexadecimal values.
Default setting
Add Shift
Add Left Ctrl
Add Left Alt
Add Right Ctrl
Add Right Alt
Add Break
For example, read labels for [Add Shift] and
the character [A].
Note: "]C1" is the Code ID of EAN-128 barcodes; "]e0" is the default Code ID of RSS
barcodes.
5.4.1 SELECT PRE-DEFINED CODE ID
Code ID options Set 1 Set 2 Set 3 Set 4 Set 5
Code 39 A C Y M A
Italian Pharmacode A C Y M A
French Pharmacode A C Y M A
Industrial 25 C H H H S
Interleaved 25 D I Z I S
Matrix 25 E G G G S
98
Enter Setup
1600 Series Barcode Scanner User Guide
Codabar F N X N F
Code 93 I L L L G
Code 128 H K K K C
UPC-E S E C E E
EAN-8 P B B FF E
EAN-13 M A A F E
UPC-A J A A A E
MSI V V D P M
Plessey W W E Q P
Telepen Z --- --- --- ---
5.4.2 CHANGE CODE ID
1) Read the label of a specific symbology below to change its code ID.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string. For
example, read “4” and “4” for applying the character [D] for Code ID.
3) Read the “Validate” label on the same page to complete this setting.
Apply Code ID Set 1
Apply Code ID Set 2
Apply Code ID Set 3
Apply Code ID Set 4
Apply Code ID Set 5
99
Update
Chapter 5 !Ζ
Configure Code ID
for Codabar
Configure Code ID
for Code 39
Configure Code ID
for Code 93
Configure Code ID
for Code 128
Configure Code ID
for EAN-8
Configure Code ID
for EAN-13
Configure Code ID for
French Pharmacode
Configure Code ID for
Italian Pharmacode
Configure Code ID
for Industrial 25
Configure Code ID
for Interleaved 25
100
Enter Setup
1600 Series Barcode Scanner User Guide
5.4.3 CLEAR CODE ID SETTINGS
Configure Code ID
for Matrix 25
Configure Code ID
for MSI
Configure Code ID
for Plessey
Configure Code ID
for Tele
p
en
Configure Code ID
for UPC-A
Configure Code ID
for UPC-E
Clear All Code ID Settings
101
Update
Chapter 5 !Ζ
5.5 LENGTH CODE
A two-digit code representing the length of barcode data (character count) can be
inserted in front of data being transmitted. Such "Length" code can be individually
enabled or disabled for each symbology.
CODABAR
CODE 39
CODE 93
CODE 128
EAN-128 & RSS
EAN-8
Apply to Codabar *Do Not Apply
*Do Not ApplyApply to Code 39
*Do Not ApplyApply to Code 93
*Do Not ApplyApply to Code 128
*Do Not ApplyApply to EAN-128 & RSS
*Do Not ApplyApply to EAN-8
102
Enter Setup
1600 Series Barcode Scanner User Guide
EAN-13
FRENCH PHARMACODE
ITALIAN PHARMACODE
INDUSTRIAL 25
INTERLEAVED 25
MATRIX 25
MSI
*
Do Not ApplyApply to EAN-13
*
Do Not ApplyApply to French Pharmacode
*
Do Not ApplyApply to Italian Pharmacode
*Do Not ApplyApply to Industrial 25
*
Do Not ApplyApply to Interleaved 25
*
Do Not ApplyApply to Matrix 25
*
Do Not ApplyApply to MSI
103
Update
Chapter 5 !Ζ
PLESSEY
TELEPEN
UPC-A
UPC-E
*Do Not ApplyApply to Plessey
*Do Not ApplyApply to Telepen
*Do Not ApplyApply to UPC-A
*Do Not ApplyApply to UPC-E
104
Enter Setup
1600 Series Barcode Scanner User Guide
5.6 MULTI-BARCODE EDITOR
The Multi-Barcode Editor allows you to decide the output sequence of a concatenation of
barcodes.
Note: Multi-Barcode Editor cannot work with “Multi-Barcode Mode”.
The barcodes that are found meeting the specified criteria below will be arranged in the
desired sequence.
Code Type
4-digit code length, including prefix, suffix, length code, etc.
Matching the first character of data
105
Update
Chapter 5 !Ζ
5.6.1 EDIT A CONCATENATION OF BARCODES
1) Read the label above to start editing a concatenation of barcodes.
2) Code Type setting – read the “Hexadecimal Value” label on page 124 for Code Type of
the (first) barcode. For example, read “4” and “1” for Code 39.
Code Type Symbology Code Type Symbology
41 (A) Code 39 4F (O) EAN-8 with Addon 5
42 (B) Italian Pharmacode 50 (P) EAN-13
43 (C) French Pharmacode) 51 (Q) EAN-13 with Addon 2
44 (D) Industrial 25 52 (R) EAN-13 with Addon 5
45 (E) Interleaved 25 53 (S) MSI
46 (F) Matrix 25 54 (T) Plessey
47 (G) Codabar (NW7) 55 (U) EAN-128
48 (H) Code 93 56 (V) UPC-A
49 (I) Code 128 57 (W) UPC-A with Addon 2
4A (J) UPC-E0 / UPC-E1 58 (X) UPC-A with Addon 5
4B (K) UPC-E with Addon 2
4C (L) UPC-E with Addon 5 5A (Z) Telepen
4D (M) EAN-8 5B ( [ ) RSS-14
4E (N) EAN-8 with Addon 2
3) Code Length setting – read the “Decimal Value” label on page 123 for the 4-digit total
length of the (first) barcode. For example, read 0065 for 65 characters or read “0000”
for any length.
Note: If not reading 0000 for any length, the 4-digit length must include prefix, suffix
(0x0d by default), length code, etc.
4) Matching Character setting – read the “Hexadecimal Value” label on page 124 for the
1st character that must be found matching in the (first) barcode. For example, read
“4” and “1” for matching character “A” as the first character in the barcode or read
“00” for any character.
5) Read twice the “F” label on page 124 (“FF”) to complete the setting of each barcode.
6) Read the label “Validate” to end the editing of the barcode set.
Edit Output Sequence
106
Enter Setup
1600 Series Barcode Scanner User Guide
5.6.2 ACTIVATE THE CONCATENATION OF BARCODES
By default, the output sequence editing of the concatenation of barcodes is not applied.
When “Enforce Output Sequence” is enabled, all barcodes read by the scanner must meet
with the criteria for the concatenation. If data is found excluded from all output sequence
sets (= not meeting with the criteria), the scanner will not accept the reading, and
therefore, data will not be transmitted.
When “Apply Output Sequence” is enabled, only barcodes found meeting with the criteria
are counted for the concatenation. Those found not meeting with the criteria are
processed normally and individually.
*Ignore Output Sequence
Enforce Output Sequence
Apply Output Sequence
107
Update
The scanner allows advanced data editing by applying user-configured editing formats.
Data is divided into fields by user-specified rules. These fields together with the
user-configurable additional fields consist of the data actually sent to the host computer.
IN THIS CHAPTER
6.1 Format Selection ......................................................108
6.2 Editing Format..........................................................110
6.3 Programming Examples .............................................123
Chapter 6
APPLYING FORMATS FOR DATA EDITING
108
End Programming Format
1600 Series Barcode Scanner User Guide
6.1 FORMAT SELECTION
6.1.1 ACTIVATE EDITING FORMATS
If you have already configured any editing format before, you may directly apply the
editing format. If not, you must start with configuring an editing format first, and then,
activate the editing format when it is desired in use.
EDITING FORMAT 1
EDITING FORMAT 2
EDITING FORMAT 3
Enable Format 1
*
Disable Format 1
Enable Format 2
*
Disable Format 2
Enable Format 3
*
Disable Format 3
109
Update
Chapter 6 !Ζ
EDITING FORMAT 4
EDITING FORMAT 5
6.1.2 EXCLUSIVE DATA EDITING
By default, only barcodes found meeting with the criteria are processed by the editing
formats. Those found not meeting with the criteria are processed normally.
When “Exclusive Data Editing” is enabled, all barcodes read by the scanner must be
processed by the editing formats. If data is found excluded from all enabled editing
formats (= not meeting with the specified criteria), the scanner will not accept the
reading, and therefore, data will not be transmitted.
Yes
*No
Enable Format 4
*Disable Format 4
*Disable Format 5
Enable Format 5
110
End Programming Format
1600 Series Barcode Scanner User Guide
6.2 EDITING FORMAT
6.2.1 SELECT FORMAT TO CONFIGURE
START PROGRAMMING FORMAT
Select one editing format (Format 1~5) and the parameters pertaining to the editing
format can then be configured – applicable code type, data length, matching string &
location, total number of fields, field settings (field-dividing rule), additional fields, and
field transmission sequence.
Up to five different formats can be specified.
Configure Format 1
111
Update
Chapter 6 !Ζ
Note: Before you complete the programming of an editing format, if you have the
scanner read any label for parameters other than those pertaining to the editing
format, it will automatically abort the programming process.
END PROGRAMMING FORMAT
After having configured all the desired parameters, you must have the scanner read the
“End Programming Format” label, which can be located at the bottom of every even page
in this chapter.
6.2.2 RESTORE DEFAULT FORMAT
You may select an existing editing format and have the defaults restored. The default
settings of an editing format are listed below.
Editing format Defaults
Applicable Code Type All
Data Length 0 (No qualification.)
Matching String Disable
Matching String Location None
Configure Format 3
Configure Format 4
End Programming Format
Configure Format 5
Configure Format 2
112
End Programming Format
1600 Series Barcode Scanner User Guide
Total Number of Fields 1
Field Setting – field-dividing rule Not configured.
Additional Fields None
Field Transmission Sequence F1
6.2.3 DEFINE DATA CRITERIA
Three applicable conditions can be configured to check whether the data read by the
scanner can be processed by the particular editing format.
Note: Data editing cannot be performed unless the three conditions are all met.
APPLICABLE CODE TYPE
By default, barcodes of all the supported symbologies will be processed by any editing
format, if having been configured and enabled.
Restore Default Format
*Apply to All Code Types
Codabar Applicable
C
ode 39 Applicable
Code 93 Applicable Code 128 Applicable
EAN-8 Applicable EAN-8 Addon 2 Applicable
Clear All
113
Update
Chapter 6 !Ζ
EAN-8 Addon 5 Applicable EAN-13 Applicable
EAN-13 Addon 2 Applicable EAN-13 Addon 5 Applicable
Italian Pharmacode Applicable Industrial 25 Applicable
Interleaved 25 Applicable Matrix 25 Applicable
MSI Applicable Plessey Applicable
UPC-A Addon 2 Applicable UPC-A Addon 5 Applicable
Telepen Applicable UPC-A Applicable
EAN-128 & RSS Applicable French Pharmacode Applicable
114
End Programming Format
1600 Series Barcode Scanner User Guide
DATA LENGTH
By default, barcodes of any length (character count) are eligible for data editing.
You may specify a value from 0 to 255.
When zero is given to both, the scanner will not perform the length qualification.
1) Read the labels for Max. /Min length separately.
2) Read the “Decimal Value” label on page 123 for the desired length.
3) Read the “Validate” label on the same page to complete this setting.
MATCHING STRING & LOCATION
By default, no matching string is specified, and therefore, it is disabled. You may enable
this feature by specifying a matching string; up to four characters are allowed.
When the Matching String Location is zero, the scanner will only check for the existence of the
matching string in the barcode data.
You may specify a value from 1 to 255 to indicate where the matching string starts in the
barcode data.
UPC-E Applicable UPC-E Addon 2 Applicable
UPC-E Addon 5 Applicable
Max. Length
Min. Length
115
Update
Chapter 6 !Ζ
1) Read the label to specify a matching string.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string.
3) Read the “Validate” label on the same page to complete this setting.
4) Read the label to specify the location of the matching string.
5) Read the “Decimal Value” label on page 123 for the desired location.
6) Read the “Validate” label on the same page to complete this setting.
6.2.4 DIVIDE DATA INTO FIELDS
START POSITION
Data can be divided into fields in one of the following direction –
from head (F1) to tail (F5)
from tail (F1) to head (F5)
FIELD ADJUSTMENT
You may apply equal length to all fields, if necessary. It will add “Space” (0x20) to field
when data is found shorter than specified.
*From Head
From Tail
Matching String …
Location of
Matching String …
116
End Programming Format
1600 Series Barcode Scanner User Guide
1) Read the label above to adjust field by length.
2) Read the “Decimal Value” label on page 123 for the desired field length.
3) Read the “Validate” label on the same page to complete this setting.
TOTAL NUMBER OF FIELDS
Data can be divided into at most 6 fields; each of them is numbered from F1 to F6
accordingly. However, only F1~F5 can be configured.
The total number of fields must be specified correctly. If three fields are configured
for the editing format, the data characters after F3 will be assigned to F4
automatically. This feature is quite useful especially when data of variable lengths is
processed by editing formats.
Set Length to adjust
f
ields …
(
*0
)
*No Adjustment
*One Field
Two Fields
Three Fields
Four Fields
Five Fields
117
Update
Chapter 6 !Ζ
Note: The number of configurable fields is always one less than the total number of
fields specified. The extra data characters beyond the last field configured will be
automatically assigned to the next field.
6.2.5 FIELD SETTINGS
Data eligible for editing formats is divided into fields by user-specified rules – either
using the field terminating string or specified field length.
By Terminating String
Specify the field terminating string. Up to two characters are allowed. The scanner will search for
the occurrence of this particular string in the data.
By default, this string will be included in the field. You may discard it.
By Length
Alternatively, you may simply specify the field length. The scanner will assign the next specified
number of characters into the field.
FIELD 1 SETTING
1) Read the label to divide field by a specified terminating string.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string.
3) Read the “Validate” label on the same page to complete this setting.
1) Read the label to divide field by length.
2) Read the “Decimal Value” label on page 123 for the desired field length.
3) Read the “Validate” label on the same page to complete this setting.
Select Field Separator
to Divide Field 1 …
*Include Separator Discard Separator
Six Fields
118
End Programming Format
1600 Series Barcode Scanner User Guide
FIELD 2 SETTING
1) Read the label to divide field by a specified terminating string.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string.
3) Read the “Validate” label on the same page to complete this setting.
1) Read the label to divide field by length.
2) Read the “Decimal Value” label on page 123 for the desired field length.
3) Read the “Validate” label on the same page to complete this setting.
FIELD 3 SETTING
1) Read the label to divide field by a specified terminating string.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string.
3) Read the “Validate” label on the same page to complete this setting.
Divide Field 1 by Length …
Select Field Separator
to Divide Field 2 …
*Include Separator
D
iscard Separator
Divide Field 2 by Length …
Select Field Separator
to Divide Field 3 …
119
Update
Chapter 6 !Ζ
1) Read the label to divide field by length.
2) Read the “Decimal Value” label on page 123 for the desired field length.
3) Read the “Validate” label on the same page to complete this setting.
FIELD 4 SETTING
1) Read the label to divide field by a specified terminating string.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string.
3) Read the “Validate” label on the same page to complete this setting.
1) Read the label to divide field by length.
2) Read the “Decimal Value” label on page 123 for the desired field length.
3) Read the “Validate” label on the same page to complete this setting.
FIELD 5 SETTING
1) Read the label to divide field by a specified terminating string.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string.
Divide Field 3 by Length …
Select Field Separator
to Divide Field 4 …
*Include Separator Discard Separator
Divide Field 4 by Length …
*Include Separator Discard Separator
120
End Programming Format
1600 Series Barcode Scanner User Guide
3) Read the “Validate” label on the same page to complete this setting.
1) Read the label to divide field by length.
2) Read the “Decimal Value” label on page 123 for the desired field length.
3) Read the “Validate” label on the same page to complete this setting.
ADDITIONAL FIELDS
Up to five additional fields can be created for each editing format; each of them is
numbered from AF1 to AF5 accordingly.
1) Read the label to specify an additional field, one at a time.
2) Read the “Hexadecimal Value” label on page 124 for the desired additional field.
3) Read the “Validate” label on the same page to complete this setting.
Additional Field 1 …
Additional Field 2 …
Select Field Separator
to Divide Field 5 …
Divide Field 5 by Length …
*Include Separator
D
iscard Separator
121
Update
Chapter 6 !Ζ
If "Keyboard Wedge" is configured for interface, Key Type and Key Status will then
become applicable. You may decide whether or not to apply Key Status when “Normal
Key” is selected for Key Type.
Key Type Key Status
Scan Code Up to 2 scan code values are allowed –
each requires two hexadecimal values.
N/A
Normal Key Up to 4 character strings are allowed –
each requires two hexadecimal values.
Default setting
Add Shift
Add Left Ctrl
Add Left Alt
Add Right Ctrl
Add Right Alt
Add Break
For example, read labels for [Add Shift],
[A], [Add Shift], and [B].
6.2.6 FIELD TRANSMISSION SEQUENCE
After configuring the data fields and additional fields, you must now program the
transmission sequence of these fields that comprise the final data. This field transmission
sequence can be assigned in any desired order and fields can be assigned multiple times
as well.
Note: Up to twelve fields can be assigned.
1) Read the “Start” label to begin with programming the field transmission sequence.
Additional Field 4 …
Additional Field 5 …
Start (Programming) …
Additional Field 3 …
122
End Programming Format
1600 Series Barcode Scanner User Guide
2) Program the transmission sequence by reading the desired fields as well as additional
fields.
3) Read the “End” label on the same page to complete this setting.
End
Field 1 Field 2
Field 3 Field 4
Field 5 Field 6
Additional Field 1 Additional Field 2
Additional Field 3 Additional Field 4
Additional Field 5
123
Update
Chapter 6 !Ζ
6.3 PROGRAMMING EXAMPLES
6.3.1 EXAMPLE I
Extract data from the 10th character to the 19th character...
The editing format should be configured as follows:
Total Number of Fields – 3.
Field 1 Setting – Divide Field by Field Length, and set length to 9.
Field 1 data starts from the 1st character to the 9th character.
Field 2 Setting – Divide Field by Field Length, and set length to 10.
Field 2 data starts from the 10th character to the 19th character.
Field Transmission Sequence – F2.
6.3.2 EXAMPLE II
Extract the date code, item number, and quantity information from barcodes.
Data in a barcode is encoded like this:
-From the 1st character to the 6th character is the date code.
-From the 7th character to the "-" character is the item number.
-After the "-" character is the quantity information.
Data will be transmitted like this:
-The item number goes first, then a TAB character, followed by the date code, then another
TAB character, and finally the quantity information.
The editing format should be configured as follows:
Total Number of Fields – 3.
Field 1 Setting – Divide Field by Field Length, and set length to 6.
Field 1 data starts from the 1st character to the 6th character.
Field 2 Setting – Divide Field by Field Terminating String, and set the character string to [-].
Field 2 data starts from the 7th character until the [-] character is met.
Additional Field 1 created and set to one [TAB] character.
Field Transmission Sequence – F2 A1 F1 A1 F3.
124
End Programming Format
1600 Series Barcode Scanner User Guide
125
Update
Optical Characteristics 1660
Scan Engine Non-contact type
Optical Sensor CCD, 2500 pixels
Light Source Red LED
Wavelength 625 nm
RF Characteristics
Bluetooth Module Bluetooth Specification Version 2.0, Class 3
Coverage (line-of-sight) Up to 3 meters
Profiles Supported Serial Port Profile (SPP), Human Interface Device Profile (HID)
Connected Devices 1 for Bluetooth HID and up to 7 scanners for Bluetooth SPP
Physical Characteristics
Color Dark grey
Switch Push-button switch, plus [Delete] key
Dimensions 95 mm (L) 35 mm (W) 20 mm (H)
Weight Approx. 50 g
Electrical Characteristics
Battery 2 AAA Alkaline batteries
SPECIFICATIONS
126
Enter Setup
1600 Series Barcode Scanner User Guide
Environmental Characteristics
Temperature Operating
Storage
0 °C to 50 °C
-20 °C to 60 °C
Humidity
(Non-condensing)
Operating
Storage
10% to 90%
5% to 95%
Electrostatic Discharge ± 15 kV air discharge, ± 8 kV direct discharge
EMC Regulation FCC, CE, C-Tick, MIC, BSMI
TELEC, NCC, RSS-210
Programming Support
Configuration via Setup Labels Use setup labels or host serial commands.
Software Windows-based ScanMaster
Firmware upgradeable Download firmware updates via the download utility.
127
Update Abort
DECIMAL SYSTEM
Decimal
Validate the Values
Appendix I
NUMERAL SYSTEMS
0
1
2
3
4
5
6
7
8
9
Validate
128
Enter Setup
1600 Series Barcode Scanner User Guide
HEXADECIMAL SYSTEM
HexaDecimal
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
129
Appendix I !Ζ
Update Abort
Validate the Values
ENTERING PIN CODE FOR BLUETOOTH CONNECTION
By default, the Bluetooth PIN code is set to “0000”. Maximum 16 characters are allowed.
Note: When using Bluetooth HID, some driver of Bluetooth dongle may not support
pre-defined PIN code for authentication. In this case, make sure you disable
authentication before pairing. The host PIN code will be displayed on the computer
screen. Have the scanner read the setup barcode “Enter PIN Code in Decimal” to
input the matching PIN code quickly.
1) Read one of the labels above to specify the PIN code, in decimal or hexadecimal.
2) Read the “Decimal Value” label on page 123 or the “Hexadecimal Value” label on page
124 for the desired digits or character string.
3) Read the “Validate” label on the same page to complete this setting.
Validate
Enter PIN Code in Hexadecimal …
Enter PIN Code in Decimal …
130
Enter Setup
1600 Series Barcode Scanner User Guide
131
Update
KEYBOARD WEDGE TABLE
0 12345678
0F2 SP 0 @ P ` p b
1INS F3 ! 1 A Q a q c
2DLT F4 " 2 B R b r d
3Home F5 # 3 C S c s e
4End F6 $ 4 D T d t f
5Up F7 % 5 E U e u g
6Down F8 & 6 F V f v h
7Left F9 ' 7 G W g w i
8BS F10 ( 8 H X h x j
9HT F11 ) 9 I Y i y k
ALF F12 * : J Z j z
BRight ESC + ; K [ k {
CPgUp Exec , < L \ l |
DCR CR* - = M ] m }
EPgDn . > N ^ n ~
FF1 / ? O _ o Dly ENTER*
Note: (1) b~k: Digits of numeric keypad.
(2) CR*/Send/ENTER*: ENTER key on the numeric keypad.
KEY TYPE
If "Keyboard Wedge" is configured for interface, Key Type and Key Status will then
become applicable.
Appendix II
KEYBOARD WEDGE TABLE & ASCII TABLE
132
Enter Setup
1600 Series Barcode Scanner User Guide
KEY STATUS
Decide whether or not to change key status when “Normal Key” is selected for Key Type.
*Normal
Scan Code
Add Shift
A
dd Left Ctrl
Add Right Ctrl
Add Left Alt
Add Right Alt
133
Update
Appendix II !Ζ
USER-DEFINED SCAN CODE
1) Read the “Set Scan Code” label to define new scan code.
2) Read the “Hexadecimal Value” label on page 124 for the desired character string.
3) Read the “Validate” label on the same page to complete this setting.
4) Read the “Confirm” label to confirm the action.
ASCII TABLE
0 1234567
0 DLE SP 0 @ P ` p
1 SOH DC1 ! 1 A Q a q
2 STX DC2 " 2 B R b r
3 ETX DC3 # 3 C S c s
4 EOT DC4 $ 4 D T d t
5 ENQ NAK % 5 E U e u
6 ACK SYN & 6 F V f v
7 BEL ETB ' 7 G W g w
8 BS CAN ( 8 H X h x
9 HT EM ) 9 I Y i y
A LF SUB * : J Z j z
B VT ESC + ; K [ k {
C FF FS , < L \ l |
D CR GS - = M ] m }
E SO RS . > N ^ n ~
F SI US / ? O _ o DEL
Set Scan Code
Confirm
134
Enter Setup
1600 Series Barcode Scanner User Guide
135
Update
SERIAL COMMANDS
#@NNNNNN<CR>
Purpose To configure the scanner.
Remarks nnnnnn – the six digits of command parameters. For example, “109952” is to list the
current Code ID settings.
“0x23” + “0x40” + “0x31” + “0x30” + “0x39” + “0x39” + “0x35” + “0x32” + “0x0d”
#@ - - - -<CR>
Purpose To halt the scanner.
Remarks “0x23” + “0x40” + “0x2d” + “0x2d” + “0x2d” + “0x2d” + “0x0d”
#@ . . . . <CR>
Purpose To resume operation.
Remarks “0x23” + “0x40” + “0x2e” + “0x2e” + “0x2e” + “0x2e” + “0x0d”
#@////<CR>
Purpose To respond with a beep.
Remarks “0x23” + “0x40” + “0x2f” + “0x2f” + “0x2f” + “0x2f” + “0x0d”
#@TRIGOFF<CR>
Purpose Disable software trigger
Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” ” + “0x46” ” +
“0x46” + “0x0d”
#@TRIGON<CR>
Purpose Enable software trigger
Remarks “0x23” + “0x40” + “0x54” + “0x52” + “0x49” + “0x47” + “0x4f” ” + “0x4e” ” +
“0x0d”
Appendix III
HOST SERIAL COMMANDS
Serial Command
List Page 3
136
Enter Setup
1600 Series Barcode Scanner User Guide
EXAMPLE
Send the serial commands via RS-232 interface or Bluetooth SPP. For example, run
HyperTerminal on the host computer.
For the scanner to change the beeper to medium volume and beep –
#@101011<CR>
#@////<CR>
For the scanner to change the beeper to minimal volume and beep –
#@101010<CR>
#@////<CR>
For the scanner to change the beeper frequency to 8 kHz (for Good Read Beep only)
and beep –
#@101001<CR>
#@////<CR>
For the scanner to change the beeper length to longest (for Good Read Beep only)
and beep –
#@101008<CR>
#@////<CR>
137
Update
You can only upgrade firmware of one Bluetooth scanner at a time. For example, you
must turn off each of the rest 1660 scanner when there is more than one scanner
connected to your computer via a Bluetooth dongle.
Note: In case it fails downloading due to low battery, make sure the targe scanner is
loaded with a fully charged battery.
1) Connect the Bluetooth dongle to your computer via the USB port.
2) Refer to 3.2 Connecting via Bluetooth Dongle for the target scanner to establish a
connection with your computer via the dongle.
Read the following labels in sequence to configure the scanner to use Bluetooth Serial
Port as output interface.
3) Read the following labels in sequence for the scanner to enter the download mode.
The scanner will respond with beeps to indicate it is ready for downloading.
Appendix IV
UPGRADING FIRMWARE
Enter Setup
Activate Bluetooth SPP
(and read labels for PIN code …)
Update
138
Enter Setup
1600 Series Barcode Scanner User Guide
4) Run the download utility “ProLoad.exe” or “Download.exe” on your computer.
(Download.exe requires version 2.3 or later!)
Open the firmware update “*.shx”, and select the correct COM port.
Baud rate – 115,200 bps
Data bit – 8
Parity – None
Flow control – None
5) The scanner will automatically restart itself when upgrading firmware is completed
successfully.
Enter Setup
Download