Cisco Systems 01 IP Camera with wireless technologies User Manual Modcam Manual
MODCAM AB IP Camera with wireless technologies Modcam Manual
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 2965000 |
| Application ID | Kp07x1bVUmfTGybKvpIF5Q== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 438.31kB (5478899 bits) |
| Date Submitted | 2016-04-21 00:00:00 |
| Date Available | 2016-04-21 00:00:00 |
| Creation Date | 2016-03-23 06:38:16 |
| Producing Software | Mac OS X 10.11.3 Quartz PDFContext |
| Document Lastmod | 2016-03-23 06:38:16 |
| Document Title | Modcam Manual.pdf |
| Document Creator | Preview |
MOD.01 User Manual
>Revision
R3 - 2015-09-14
Federal Communication Commission
Interference Statement
FCC Part 15
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
4. Consult the dealer or an experienced radio technician for help.
FCC Caution
This equipment must be installed and operated in accordance with provided
instructions and a minimum 20 cm spacing must be provided between
computer mounted antenna and person’s body (excluding extremities of hands,
wrist and feet) during wireless modes of operation.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the authority to operate equipment.
Federal Communication Commission (FCC) Radiation Exposure
Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm (8 inches) during normal operation.
The antenna(s) used for this transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
The equipment version marketed in US is restricted to usage of the channels
1-11 only.
Industry Canada Statements
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference that may cause undesired operation
of the device.
This equipment complies with the safety requirements for RF exposure in
accordance with RSS-102 §2.5.2. This equipment must be installed and
operated in accordance with the provided instructions and a minimum 20 cm
spacing must be provided between the antenna and any person’s body
during wireless modes of operation.
Cet appareil est conforme avec Industrie Canada exempt de licence
Rss standard(s). Son fonctionnement est soumis aux deux conditions
suivantes : (1) cet appareil ne peut causer d’interférences, et (2) cet appareil
doit accepter toute interférence, y compris des interférences qui peuvent
provoquer un fonctionnement indésirable du périphérique.
Ce dispositife est conforme à la norme de sécurité en matière d'exposition
RF conformément à la RSS-102 §2.5.2. Ce dispositif doit être installé et
utilisé conformément aux instructions fournies et à 20 cm espacement
minimal doit être prévu entre l'antenne et le corps de toute personne pendant
les modes sans fil de fonctionnement.
(i)
(ii)
(I)
(II)
The device for operation in the band 5150–5250 MHz is only for
indoor use to reduce the potential for harmful interference to cochannel mobile satellite systems;
Users should also be advised that high-power radars are allocated
as primary users (i.e. priority users) of the bands 5250-5350 MHz
and 5650-5850 MHz and that these radars could cause
interference and/or damage to LE-LAN devices
Le dispositif pour fonctionner dans la bande 5150-5250 MHz est
uniquement pour une utilisation en intérieur afin de réduire les
risques d'interférences nuisibles à la co-canal des systèmes
mobiles par satellite;
Les utilisateurs doivent également être informés que les radars à
haute puissance sont désignés comme utilisateurs principaux (c.à-utilisateurs prioritaires) des bandes 5250-5350 MHz et 56505850 MHz et que ces radars pourraient provoquer des
interférences et / ou endommager LE-LAN dispositifs
R&TTE Compliance Statement
This equipment complies with all the requirements of DIRECTIVE 1999/5/EC
OF THE EUROPEAN PARLIAMENT AND THE COUNCIL of March 9, 1999 on
radio equipment and telecommunication terminal Equipment and the mutual
recognition of their conformity (R&TTE).
The R&TTE Directive repeals and replaces in the directive 98/13/EEC
(Telecommunications Terminal Equipment and Satellite Earth Station
Equipment) As of April 8, 2000.
Safety
This equipment is designed with the utmost care for the safety of those who
install and use it. However, special attention must be paid to the dangers of
electric shock and static electricity when working with electrical equipment. All
guidelines of this and of the computer manufacture must therefore be allowed
at all times to ensure the safe use of the equipment.
EU Countries Intended for Use
The ETSI version of this device is intended for home and office use in Austria,
Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy,
Luxembourg, the Netherlands, Portugal, Spain, Sweden, and the United
Kingdom.
The ETSI version of this device is also authorized for use in EFTA member
states: Iceland, Liechtenstein, Norway, and Switzerland.
EU Countries Not intended for use
None.
Introduction
About Modcam
Intelligent and open – the beginning of a new era in computer vision.
Over the years, the hyper-growth in the mobile industry has pushed down cost of
components immensely and opened up for a great developer community. At Modcam, we
have used this opportunity and applied logics from the smartphone industry to develop a
new solution for computer vision.
Modcam provides an outstanding platform for intelligent computer vision applications. We
have created a smart piece of hardware and an open software architecture to breed new
exciting opportunities within computer vision. The platform enables videos and pixels to be
translated into information, before being distributed to a network. Our platform is tailored
for video content analytics applications through our unique knowledge about image
processing and the interaction between software, hardware, and camera sensor. Modcam
gives you the ability to see, understand and react.
About the MOD.01
The MOD.01 is a powerful quad core ARMv7 platform with a 5 megapixel camera sensor,
GPS, accelerometer, compass, microphone and enough storage and memory to run
advanced computer vision applications without pause.
It is physically built and adapted to be as versatile as possible with regards to mounting
needs and environmental conditions and packaged in a sleek and non-intrusive design. It
comes with full WiFi and Bluetooth 4.0 stacks and there are options for Ethernet adapters
with PoE support for larger installation.
While the MOD.01 is mainly designed to be continuously powered via it’s micro-usb
connector, it comes with a 800mAh battery inside that will both allow it to retain operation
during power outages and last for up to a full day where external power supply is limited.
This document
This document describes basic properties, usage and handling of the MOD.01 hardware
product, including setup experience, installation and mounting options.
>Revision
R3 - 2015-09-14
General product handling
Unpacking and general considerations
Included with your MOD.01 device should be a three metres, charging-only, Micro-b to
Type-A USB cable, a 1A USB Type-A power adapter for your region and a standard two-part
MOD.01 ceiling mount intended for top-down coverage1.
Boot, shutdown and LED patterns
The MOD.01 device will automatically boot whenever it receives power through its micro-b
USB contact. This means that as a safe-guard against power outages, if power is inserted, it
will automatically boot even when manual shutdown has been performed.
Upon boot, the device will go through a series of patterns with the four LEDs situated
around the camera lens of the unit.
Shutdown
To turn off the device, remove any power source and press the button for at least 6
seconds. During this time, the LEDs will show a countdown pattern (after a couple of
seconds). The countdown ends with a four LED white flash, indicating that the shutdown is
complete.
Standard LED behaviour
1.
2.
3.
4.
5.
6.
7.
8.
Blue lower right/left light - Pre-boot phase.
Blue l ights, spinning - Booting.
Four o
range lights, flashing - Not connected to network, scanning for QR code.
Four g
reen lights, flashing - QR code scanned.
Orange l ights, spinning - Connecting to network.
Orange l ights, alternately flashing left/right - Network connection failed.
Yellow lights, pulsating - Connected, installation not finished, video stream possible.
White lights, slowly pulsating - Connected, installed and ready.
Note: S
pinning red lights indicate an ongoing over-the-air (OTA) upgrade. Never shut down
the device during this process!
Configuration
The actual contents of your package may vary depending of OEM-packaging and point of resale.
>Revision
R3 - 2015-09-14
Once your device has completed booting it will start flashing orange with all four LEDs,
indicating that it is ready to read a QR code for configuration.
In a browser, navigate to h
ttps://setup.modcam.com and follow the instructions!
Upgrades
The device upgrades itself over-the-air whenever new software is ready to be deployed to
the device. An automatic update check is performed immediately after acquiring a network
connection and then once every 24 hours. The timeframe for the update check is by default
between 3 and 4 in the morning, local time.
Note: Do not shut off the device once it has started upgrading the system, indicated by
spinning red LEDs.
Installation
When the device is ceiling-mounted you can calculate the approximate floor coverage area
A for height H
with the formula:
A = 1.78H 2
If the sensor has the optional wide angle lens attached, the formula to use is
A = 10.37H 2
This means that for a ceiling height of 4 metres, the approximate floor coverage is ~28m2,
or ~166m2 with the wide angle lens.
Applications
For applications running on the MOD.01, please refer to the application-specific
documentation.
>Revision
R3 - 2015-09-14
Specifications
Application processor
MOD.01 is built on a Broadcom chipset - BCM23550, compliant with ARM TrustZone® and
GlobalPlatform for system-level security.
●
●
●
●
●
Quad 1GHz A7 CPU with ARM® NEONTM technology
High-performance VideoCore IV GPU
Integrated image signal processor (ISP) with support up to 12 megapixels
High quality H.264 full HD (1080p30) camcorder and video playback
Power management techniques that increase efficiency and optimize performance
based on workload demands
Memory subsystem
MOD.01 holds memory in package based on Samsung’s MCP (Multi Chip Package)
technology that allows integration of multiple memory chips of different types, such as
NAND flash, eMMC and mobile DRAM, in a single package. MCP-based memory enables the
rest of the application to view the memory subsystem as a single, unified "block", letting
the memory subsection offer the highest levels of performance for the device.
●
●
Density: eMMC(4GB)+LPDDR2(1GB)
Max speed: 1066 Mbps (LPDDR2)
Sensor subsystem
Camera
MOD.01 is using a 5 megapixel camera with fixed focus.
●
●
●
●
●
●
●
●
Resolution: 2592 x 1944 pixels – 5.0 MP
1/4” CMOS Sensor (Omnivision OV5648)
Lens type – fixed focus (distance 60cm)
View Angle: 87.9±3°
Output format: 8-/10 bit RGB RAW output
Max S/N ratio: 34dB
Dynamic Range: 67dB @8x gain
Transfer rate:
○ QSXGA (2592x1944) @15fps
○ 1080p @30fps
>Revision
R3 - 2015-09-14
●
●
○ 720p @60fps
○ VGA @90fps
Sensitivity: 600mV/Lux-sec
Rolling shutter
Accelerometer/Gyro
MOD.01 is using a Bosch BMI055 ultra-small, 6 axis inertial sensor with very low-noise
measurement of angular rates and accelerations in 3 perpendicular axes and thus senses
tilt, motion, shock and vibration.
●
●
digital, triaxial 12bit acceleration sensor
digital, triaxial 16bit, ±2000°/s gyroscope.
eCompass
MOD.01 is using a Bosch BMM150 standalone geomagnetic sensor for consumer market
applications. It allows programmable and flexible measurements of the magnetic field in
three perpendicular axes with ultra-low voltage operation.
Microphone
MOD.01 is using an omnidirectional, high sensitivity - “Ultra‑Mini” SiSonicTM Microphone for
sensing noise in the surrounding environment.
>Revision
R3 - 2015-09-14
Further questions and support
For further questions and support, please contact Modcam AB directly.
contact@modcam.com
>Revision
R3 - 2015-09-14
User Login:
Please login at : dashboard.modcam.com
User Interface and People count
Depending on credentials and applications the user have bought the UI is looking
as below – the user has the possibility to watch, compare, extract data for
multiple sensors
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf Linearized : No Page Count : 29 PDF Version : 1.4 Title : Modcam Manual.pdf Producer : Mac OS X 10.11.3 Quartz PDFContext Creator : Preview Create Date : 2016:03:23 06:38:16Z Modify Date : 2016:03:23 06:38:16ZEXIF Metadata provided by EXIF.tools