Cisco Systems 2400-MDM08-R1 CPE Transceiver-Model 2.4 GHz LCD Modem Release 1 User Manual Ripwave Modem User Guide

Download:
Mirror Download [FCC.gov]
Document ID	472237
Application ID	zyu0SazgPqOg8E+FKqPCVA==
Document Description	User guide
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	175.19kB (2189900 bits)
Date Submitted	2004-09-24 00:00:00
Date Available	2004-09-24 00:00:00
Creation Date	2004-07-05 14:01:29
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2004-07-05 14:04:09
Document Title	Ripwave Modem User Guide
Document Creator	Acrobat PDFMaker 6.0 for Word
Document Author:	M. Cox

Ripwave™ Modem User Guide
For use with all Ripwave Modem models
Part Number 40-00097-00
Revision F, Version 1.0
May 21, 2004
Proprietary
All information disclosed by this document is the proprietary property of Navini Networks, Inc. and is protected
by copyright, trademark, and/or trade secret laws. All rights therein are expressly reserved.
Ripwave Modem User Guide
Navini Networks, Inc.
TABLE OF CONTENTS
INTRODUCTION.......................................................................................................................................7
PACKAGE INVENTORY .........................................................................................................................7
RIPWAVE MODELS.................................................................................................................................7
OPERATING FREQUENCIES .........................................................................................................................8
COMPUTER CONNECTIONS .........................................................................................................................8
MINIMUM COMPUTING REQUIREMENTS ......................................................................................9
PHYSICAL CHARACTERISTICS ........................................................................................................10
INSTALLING AN ETHERNET MODEM ............................................................................................12
INSTALLING A USB MODEM..............................................................................................................15
ACCESSING THE INTERNET..............................................................................................................19
TROUBLESHOOTING ...........................................................................................................................20
INDICATOR LIGHTS OR LCD DISPLAY .....................................................................................................20
INSTALLING NAVINI MONITOR.......................................................................................................21
USING NAVINI MONITOR ...................................................................................................................25
UNINSTALLING NAVINI MONITOR .................................................................................................28
INSTALLING NAVINI DIAGNOSTICS...............................................................................................29
USING NAVINI DIAGNOSTICS ...........................................................................................................32
UNINSTALLING NAVINI DIAGNOSTICS .........................................................................................35
INSTALLING & CHARGING THE BATTERY..................................................................................36
2.4 GHZ BATTERY ...................................................................................................................................36
2.3 GHZ, 2.5 GHZ, 2.6 & 3.5 GHZ BATTERY .........................................................................................37
CARE & MAINTENANCE .....................................................................................................................38
UPGRADING THE MODEM .................................................................................................................38
™
ADDENDUM 1: RIPWAVE MODEM - PC TROUBLESHOOTING ............................................39
ADDENDUM 2: END USER SOFTWARE LICENSE AGREEMENT.............................................44
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Ripwave Modem User Guide
Permissions, Trademarks & Distribution
Copyright© 2001 - 2004, Navini Networks, Inc. All information contained herein and disclosed by this
document is confidential and the proprietary property of Navini Networks, Inc. and all rights therein are
expressly reserved. Acceptance of this material signifies agreement by the recipient that the information
contained in this document is confidential and that it will be used solely for the purposes set forth herein.
Acceptance of this material signifies agreement by the recipient that it will not be used, reproduced in
whole or in part, disclosed, distributed, or conveyed to others in any manner or by any means – graphic,
electronic, or mechanical, including photocopying, recording, taping, or information storage and retrieval
systems – without the express written permission of Navini Networks, Inc.
Navini Networks, the Navini Networks logo, Internet at the Speed of Thought, Zero-Install, Ripwave,
and Unwired by Navini are trademarks of Navini Networks, Inc. Other product and company names
mentioned herein may be trademarks and/or service marks of their respective owners.
Except for the hardware warranty, nothing herein constitutes any representation, warranty,
assurance, or guaranty of any kind.
Because of continuing developments and improvements in design, manufacturing, and deployment,
material in this document is subject to change without notification and does not represent any
commitment or obligation on the part of Navini Networks, Inc.
Navini Networks, Inc. shall have no liability for any error or damages resulting from the use of this
document.
All Navini Networks logos and trademarks are the property of Navini Networks, Inc. Unauthorized usage
is strictly prohibited without the express written permission of Navini Networks, Inc.
© 2001 - 2004 Navini Networks, Inc. All rights reserved.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Ripwave Modem User Guide
Navini Networks, Inc.
Safety
When using Navini Ripwave electronic equipment, always follow basic safety precautions to reduce the
risk of electrical shock, fire, and injury to people and/or property. Follow all warnings and instructions
that come with the equipment.
1. Do not use the equipment while you are in a bathtub, shower, pool, or spa. Exposure of the
equipment to water could cause severe electrical shock or serious damage to the equipment.
2. Do not immerse the equipment in any type of liquid. Use a damp clothe and if needed, water and a
mild detergent to clean the plastic shell. Unplug the equipment from the power source before
cleaning.
3. Follow all airport and FAA regulations when using the equipment on or near aircraft.
4. Only operate the equipment from the type of power source(s) indicated in this manual (110/220
VAC, 60/50 Hz adapter or Navini supplied battery). Any other type of input power source may cause
damage to the equipment.
5. Power the equipment using only the battery or the AC adapter cable provided, and in accordance with
the instructions specified in the user manual.
6. Do not use a frayed or damaged power cord. Do not place the power cord where it can be stepped on
or tripped over.
7. Do not touch wires where the insulation is frayed or worn unless the equipment has been
disconnected from its power source.
8. Do not overload wall outlets, power strips, or extension cords. This can cause serious electrical shock
or fire.
9. Do not place the equipment on an unstable surface. It can fall and cause injury or damage to the
equipment.
10. Do not disassemble the equipment. Removing covers exposes dangerous voltages or other risks and
also voids the warranty. Incorrect reassembly can cause equipment damage or electrical shock. Only
an authorized repair technician should service this product.
11. Do not expose the equipment to extreme hot or cold temperatures.
12. Do not use the equipment under the following conditions:
• When the equipment has been exposed to water or moisture.
• When the equipment has been damaged.
• When the power cord is damaged or frayed.
• When the equipment does not operate properly or shows a distinct change in performance.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Ripwave Modem User Guide
Regulatory Information
FCC Notice
CAUTION: This device is a Radio Frequency transmitter. It is required to comply with FCC RF
exposure requirements for transmitting devices. A minimum separation distance of 8 inches (20
cm) or more must be maintained between the antenna and all persons during device operations to
ensure compliance with the FCC’s rules for Radio Frequency Exposure. If this minimum distance
cannot be maintained, exposure to RF levels that exceed the FCC’s limits may result.
FCC Compliance and Advisory Statement
Tested To Comply
With FCC Standards
FOR HOME OR OFFICE USE
This equipment has been tested and found to comply with the limits for a class B digital device,
Pursuant to Part 15 of the FCC rules. The operation is subject to the following two conditions:
(1)
This device may not cause harmful interference, and
(2)
This device must accept any interference received, including interference that may cause
undesired operation.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy
and, if not installed or used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
1)
Reorient or relocate the receiving antenna,
2)
Increase the separation between the equipment and the receiver,
3)
Connect the equipment to an outlet on a circuit that is different from the one to which the
receiver is connected,
4)
Consult the dealer or an experienced radio/TV technician for additional suggestions.
INFORMATION TO USER
This device has been authorized as a radio frequency transmitter under the appropriate rules of the
Federal Communications Commission. Any changes or modifications not expressly approved by
Navini Networks could void the user’s authority to operate the equipment.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Ripwave Modem User Guide
Navini Networks, Inc.
Battery Precautions
CAUTION! To reduce risk of injury or fire, follow these instructions when handling the battery.
1. Risk of explosion is possible if the battery is replaced with one not supplied by Navini Networks.
2. Do not dispose of the battery in a fire. They may explode. Check with the local codes for battery
disposal guidelines.
3. Do not open or mutilate the battery. The battery contains substances that are toxic, corrosive, or
harmful to humans. If battery substances come in contact with the skin, seek medical help
immediately.
4. Do not attempt to recharge the battery by any means except per the instructions in this manual.
5. Remove the battery from the equipment if the equipment is not going to be used for a long period of
time. The battery could leak and cause damage to the equipment.
6. Exercise care when handling the battery to prevent shorting the battery with conducting materials
such as bracelets, rings, and keys.
7. Store the battery pack in a dry place, 0 to +40 degrees Celsius.
8. Dispose of used batteries according to environmental guidelines.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Ripwave Modem User Guide
Introduction
Congratulations! The Ripwave™ Modem is a user-friendly, easy-toinstall device that helps you connect wirelessly to the Internet. It
provides complete broadband Internet access to residential and
small office/home office (SOHO) customers without the necessity
of professional hardware installation. The Ripwave Modem also
provides nomadic service availability as a computer with this
device is moved from room to room, location to location, or even
city to city as long as there is coverage in the area.
Package
Inventory
Please verify the contents of your Ripwave Modem package. If you
do not find all of these items in your package, notify the supplier
from whom you obtained it.
• Ripwave Modem
• Ripwave Modem AC power adapter
• PC-to-Ripwave Modem cable (USB or Ethernet straight cable)
• Ripwave Modem User Guide (on CD)
• Ripwave Modem Quick Installation Guide
• Ripwave Monitor Installation CD
Ripwave Models
Your Ripwave Modem will operate in either the 2.3 GHz, 2.4 GHz,
2.5 GHz, 2.6 GHz, 3.4 GHz, or 3.5 GHz range. Within each
frequency range there are several model types, described on the
next page. The 2.4 GHz Modem varies slightly in appearance.
2.4 GHz LED
Modem
2.4 & 3.5 GHz
LCD Modem
2.3, 2.5, 2.6, 3.4 & 3.5
GHz Modem
Also, in Release 4.0, the 2.4 GHz Modem is available in both an
LED and LCD version. In the future, an LCD version of the
Modem will be available for the 2.5, 2.6 and 3.5 GHz Modems.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Ripwave Modem User Guide
Operating
Frequencies
Navini Networks, Inc.
Modem
Model
Frequency Range
2.3 GHz
2300E/U
2.305 GHz to 2.385 GHz
Operating
Band
WCS+
2.4 GHz
2.5 GHz
2.6 GHz
3.4 GHz
3.5 GHz
2400 E/U
2500 E/U
2600 E/U
3400 E/U
3500 E/U
2.400 GHz - 2.480 GHz
2.500 GHz - 2.596 GHz
2.596 GHz – 2.686 GHz
3.410 GHz – 3.525 GHz
3.500 GHz – 3.600 GHz
ISM
MMDS/ITFS
MMDS/ITFS
BWA/FWA
BWA/FWA
The “E” in the model name stands for Ethernet, and the “U” in the
model name stands for Universal Serial Bus (USB). Your computer
will have one of these two types of ports for connecting the
Modem.
Computer
Connections
•
An Ethernet connection will function with any Win32
Operating System (Windows® 95 or later).
•
A USB connection will function only with Windows 98,
Windows 98SE, Windows 2000, Windows ME, or Windows
XP. It will not work with Windows 95 or Windows NT.
You must have the Ripwave Modem model with the appropriate
connection for your computer port.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Minimum
Computing
Requirements
Ripwave Modem User Guide
Operating
System1:
(See, also, Addendum 1)
CPU:
RAM:
Hard Drive:
Monitor:
Ethernet Modems: Any Win32® Operating System
(OS) - Windows® 95, Windows 982, Windows
98SE2, Windows 2000, Windows ME2, Windows
XP, or later version. Windows XP must be Service
Pack Level 1 or higher. Internet Explorer 3.0 or
higher is required for installation on Windows 95
Operating Systems.3
USB Modems: Windows® 982, Windows 98SE2,
Windows 2000, Windows ME2, Windows XP,
or later version. USB will not work with Windows
95 or Windows NT. Windows XP must be Service
Pack Level 1 or higher. 3
General Information:
Ensure that the pc network port is enabled.
MacIntosh systems and Lynx/Unix systems are
not supported.
Pentium level or higher
32 MB or the Operating System minimum,
whichever is greater
10 MB free disk space for Navini Monitor software
256 colors, 800 x 600 resolution
NOTE: If you are going to upgrade your Operating System after loading the
Navini Monitor or Navini Diagnostics software, you must first uninstall Navini
Monitor or Navini Diagnostics prior to upgrading the OS. Otherwise, the Navini
Monitor or Navini Diagnostics will not work. See Uninstall instructions in this
Guide.
NOTE: The Ripwave Modem must be left powered ON whenever you shut
down or restart any Windows 98 or ME platforms. If the Modem is off, a blue
screen appears on the monitor. In the event that happens you will most likely
have to power cycle the PC.
NOTE: Navini Diagnostics Tool software is supported on Win98, Win98SE,
Win2000, WinME, WinXP or higher, Mac X or higher,or Red Hat Linux 8.0 or
higher.
The Ripwave Modem installation sections include instructions for
both Ethernet and USB connections. Be sure to use the instructions
that apply to your Ripwave model. The Navini Monitor software
installation procedure is the same for any of the Ripwave models.
This manual will guide you through the simple process of installing
the Ripwave Modem and software, which has been developed to
optimize the ease and convenience for you, our valued customer.
The 2.6 GHz model is used in most of the illustrations in this
manual where there are no differences in the 2.3, 2.4, 2.5, 2.6, 3.4
& 3.5 GHz models.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Ripwave Modem User Guide
Navini Networks, Inc.
If you experience any difficulties with your unit, please contact
your Service Provider or the vendor from whom you obtained your
Ripwave Modem.
Physical
Characteristics
The 2.4 GHz Ripwave Modem varies in some aspects from the 2.3,
2.5, 2.6, 3.4 and 3.5 Modems. As well, the Ethernet connection on
any model varies from a USB connection. Notice the differences
highlighted in the photos below and on the following page.
2.4 GHz LED Ripwave Modem
Antenna
Indicator Lights
On/Off Switch
Power Adapter
Connection
Ethernet Cable
Connection
USB Cable
Connection
Back of 2.4 E
10
Back of 2.4 U
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Physical
Characteristics,
Continued
Ripwave Modem User Guide
2.3, 2.5, 2.6, & 3.5 GHz LED Ripwave Modems
Antenna
Indicator Lights
On/Off Switch
Power Adapter
Connection
Ethernet Cable
Connection
USB Cable
Connection
Back of 2.3,
2.5, 2.6 & 3.5 E
Part #40-00097-00 Rev F v1.0
May 21, 2004
Back of 2.3,
2.5, 2.6 & 3.5 U
11
Ripwave Modem User Guide
Installing an
Ethernet Modem
(See, also, Addendum 1)
Navini Networks, Inc.
The following instructions are for the installation of a Ripwave
Modem that has a USB connection. Please read all instructions
before attempting the installation. It is advisable to turn off the
computer and the Ripwave Modem before performing the
installation.
Step Action
1.
Connect the Ethernet
cable to the Ethernet
port on the computer.
2.
Illustration (using LED Modem)
Connect the other end of
the Ethernet cable to the
Ripwave Modem.
Ethernet
3.
Connect the AC power
adapter to the Ripwave
Modem. Plug the other
end into a 110/220 VAC
60/50 Hz outlet.
CAUTION! Only use
the AC power adapter
specifically supplied
with the Ripwave
Modem. Using any other
adapter may cause
damage to the Modem.
12
AC Power
adapter cable
jack
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Installing an Ethernet
Modem, continued
Ripwave Modem User Guide
Step Action
4.
Rotate the antenna on
the Ripwave Modem
clockwise 180 degrees
to the UP position. This
reveals the Ripwave
Modem indicator lights.
Illustration (using LED Modem)
Antenna
CAUTION! Rotation or
movement of the
antenna in any other
direction may cause
damage to the Ripwave
Modem.
Signal Strength
Indicator (SSI)
Battery
Indicator
Power
Indicator
5.
6.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Turn the Modem ON.
On the 2.4 GHz modem,
do this by flipping the
On/Off switch to the up
position. On all other
models, push the On/Off
button in.
If the green Power LED
lights, proceed to Step 7.
(On an LCD Modem,
the display turns on.) If
not, there is a problem
with the Modem or the
AC power adapter.
Check all cables for
proper connection. If
there is still a problem,
contact the supplier who
gave you the package.
2.3, 2.5, 2.6,
2.4 GHz
& 3.5 GHz
On/Off
Switch
Power
Indicator
13
Ripwave Modem User Guide
Installing an Ethernet
Modem, continued
14
Navini Networks, Inc.
Step Action
Turn your computer on
7.
and log in.
8.
Proceed to the
“Troubleshooting /
Installing Navini
Monitor” section of this
manual.
Illustration
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Installing a USB
Modem
(See, also, Addendum 1)
Ripwave Modem User Guide
The following instructions are for the installation of a Ripwave
Modem that has a USB connection. Please read all instructions
before attempting the installation. It is advisable to turn off the
computer and the Ripwave Modem before performing the
installation.
Step Action
1.
Connect the USB cable
to the USB port on the
computer.
2.
Illustration (using LED Modem)
Connect the other end of
the USB cable to the
back of the Ripwave
Modem.
USB Port
3.
Connect the AC power
adapter cable to the back
of the Ripwave Modem.
Plug the other end of the
cable into a 110/220
VAC, 60/50 Hz outlet.
CAUTION! Only use
the AC power adapter
specifically supplied
with the Ripwave
Modem. Using any other
adapter may cause
damage to the Modem.
Part #40-00097-00 Rev F v1.0
May 21, 2004
AC Power
adapter cable
jack
15
Ripwave Modem User Guide
Installing a USB Modem,
continued
Navini Networks, Inc.
Step Action
4.
Rotate the antenna on
the Ripwave Modem
180 degrees to the UP
position. This reveals
the Modem’s indicator
lights.
Illustration (using LED Modem)
Antenna
CAUTION! Rotation of
the antenna in any other
direction may cause
damage to the Modem.
Signal Strength
Indicator (SSI)
Battery
Indicator
Power
Indicator
5.
6.
16
Turn the Modem ON.
On the 2.4 GHz modem,
do this by flipping the
On/Off switch to the up
position. On all other
models, push the On/Off
button in.
If the green Power LED
lights, proceed to Step 7.
(On an LCD Modem,
the display turns on.) If
not, there is a problem
with the Modem or the
AC Power Adapter.
Check all cables for
proper connection. If
there is still a problem,
contact the supplier who
gave you the package.
2.3, 2.5, 2.6
& 3.5 GHz
2.4 GHz
On/Off
Switch
Power
Indicator
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Installing a USB Modem,
Continued
Ripwave Modem User Guide
Step Action
Turn your computer ON
7.
and log in.
8.
9.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Illustration
NOTE: For Windows
2000, you must be
logged into an account
having Administrative
privileges to install the
Ripwave Modem and its
software.
Plug-and-Play will
detect the Ripwave
device now attached to
the computer, and it will
launch the Plug-andPlay application.
If this does not happen,
the problem may be due
to one of the following:
• Windows NT and
Windows 95 do not
support a USB
device.
• The Modem is not
turned on.
• The Modem is not
connected properly
to the computer.
The Add New Hardware
Wizard dialog box
appears. Click Next to
continue.
17
Ripwave Modem User Guide
Installing a USB Modem,
Continued
18
Navini Networks, Inc.
Step Action
10.
Insert the Ripwave
Installation CD into the
computer’s CD-ROM
drive.
11.
Select the ‘Search for
the best driver for your
device’ option. Click
Next to continue.
12.
Select the ‘CD-ROM
drive’ checkbox. Click
Next to continue.
13.
Confirm that the drive
location is correct (it
may be different than
the one shown in the
illustration). The file to
be installed should say
‘NETNNUSB.INF”.
Click Next to continue.
Illustration
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Installing a USB Modem,
Continued
Ripwave Modem User Guide
Step Action
14.
Windows will finish
installing the software
files required for the
Ripwave Modem
operation. Click Finish.
15.
16.
Accessing the
Internet
Part #40-00097-00 Rev F v1.0
May 21, 2004
Illustration
NOTE: For Window 98,
a window may appear
asking for drivers to be
installed from the
Windows 98 setup disk.
If so, insert the
Windows 98 setup disk
into the CD-ROM drive
at this time and accept
the defaults.
After clicking Finish,
the System Settings
Change window appears
asking if you want to
restart your computer
now. Click Yes.
You must restart your
computer at this point
before proceeding.
After the computer
restart is complete,
proceed to the
“Troubleshooting /
Installing Navini
Monitor” section of this
manual.
With your Modem now installed, and both the Modem and
computer powered on, you should be able to surf the Internet! To
access the Internet, open the web browser that is installed on your
computer.
19
Ripwave Modem User Guide
Troubleshooting
Navini Networks, Inc.
After installation, if you are experiencing difficulties with your
Internet connection, please review the Minimum Computing
Requirements and Addendum 1 to ensure your computer meets
those requirements. Next, go back over the installation procedures
and ensure those steps were completed properly.
Assuming the computer requirements are met and the installation
steps were completed as required, you will need to observe the
light indicators on the front of the Modem. You also may need to
install the monitoring software. This software is provided on a CD
that came in your Modem package. Navini offers two types of
monitoring software. The first type, called the Navini Ripwave
Monitor, is available with Ripwave Modems that have a software
release prior to release 4.0. The second type, called the Navini
Diagnostics Tool, is available with Ripwave Modems that have a
software release of 4.0 or greater.
The Navini Monitor and Navini Diagnostics software assists in
solving connection problems as well as providing information
about the battery power in cases where batteries are used. Batteries
are optional with some Ripwave LED Modems.
Indicator Lights or
LCD Display
The indicator lights on the front of the LED Modem provide
valuable information about its operation. They change appearance
to designate the state of the items that they represent. Used in
conjunction with the monitoring software, you can troubleshoot
signal issues, network connections, and power problems.
The LCD Display performs the same function as the indicator
lights. However, instead of using colored lights, it provides a
written message and symbols within the display.
Signal Strength
Indicator (SSI)
Sync Indicator
Signal Strength Bars
Battery
Indicator
Power
Indicator
20
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Indicator Lights or LCD
Display, Continued
Ripwave Modem User Guide
LED Indicator Lights:
Signal Strength Indicator (SSI) Light
Constant Green:
Strong signal
Constant Yellow: Medium signal
Constant Red:
Weak signal
Flashing Red:
No signal
Battery Indicator Light
Constant Yellow: Battery is charging
Constant Red:
Battery is less than 20% charged
Flashing Red:
Battery is less than 10% charged
Off:
Battery is fully charged or not installed
Power Indicator Light
Constant Green:
The Modem is ON (AC or DC power)
LCD Display Symbols
Sync Indicator
Signal Strength
Bars
Installing
Ripwave
Monitor
Antenna symbol appears when the Modem is in sync and
sync strength = −110 dBm.
1 bar means signal strength > −110 dBm and ≤ −90 dBm
2 bars mean signal strength > −90 dBm and ≤ −80 dBm
3 bars mean signal strength > −80 dBm and ≤ −70 dBm
4 bars mean signal strength > −70 dBm
Navini’s monitoring software (Ripwave Monitor or Navini
Diagnostics) provides two types of information: signal strength and
quality of the incoming signal. It also can provide information
about the connectivity to the Service Provider’s network. These
displays may be required when troubleshooting Modem problems.
The next few sections will discuss how to install, troubleshoot
with, and uninstall your Ripwave Monitor software. If your
Ripwave Modem has a software release of 4.0 or greater, you do
not have the Ripwave Monitor. You have the Navini Diagnostics
software. You should refer to the sections that discuss how to
install, troubleshoot with, and uninstall your Navini Diagnostics
software.
Before you install your Ripwave Monitor software, please note:
For Windows NT and Windows 2000 you must log into an
account having Administrative privileges in order to install the
Navini Monitor software.
For Windows 95, 98, and 98SE Operating Systems (OS), the
OS CD may be required to complete this installation. If
prompted, insert the OS CD into the CD-ROM drive and accept
the defaults.
Part #40-00097-00 Rev F v1.0
May 21, 2004
21
Ripwave Modem User Guide
Navini Networks, Inc.
Installing Ripwave
Monitor, Continued
After the Ripwave Monitor software is loaded, if you must
upgrade your PC OS, first uninstall Ripwave Monitor prior to
upgrading the OS. Otherwise, Ripwave Monitor will not work.
See Uninstall instructions in this Guide.
•
Step Action
Illustration
1.
Shut down all programs,
including anti-virus
software programs,
before installing the
Ripwave Monitor
software.
2.
Insert the Ripwave
Monitor Installation CD
into the CD-ROM drive.
3.
At the bottom left-hand
corner of your screen,
click Start > Run. In
the Run window, enter
e:\setup in the Open
field (where “e”
represents the CD
drive). Use whatever
letter represents your
CD drive. Click OK to
continue.
4.
The InstallAnywhere
window appears. The
progress bar indicates
that InstallAnywhere has
initialized.
5.
22
The Ripwave Monitor
Introduction screen
appears. Click Next to
continue.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Installing Ripwave
Monitor, continued
Ripwave Modem User Guide
Step Action
Illustration
6.
The License Agreement
screen appears. Read the
Licensing Agreement.
Select the I Accept
option, and click Next to
continue.
NOTE: If the License
Agreement is not
accepted, you cannot
install the software.
7.
The Ripwave
Positioning screen
appears. Read the screen
for positioning the
Ripwave Modem for
optimum performance.
Click Next to continue.
8.
The Choose Install
Folder screen appears.
Enter the name of the
folder where you wish to
install the software.
Click Next to continue.
The default installation
folder provided by the
software is shown in the
illustration.
Part #40-00097-00 Rev F v1.0
May 21, 2004
23
Ripwave Modem User Guide
Installing Ripwave
Monitor, continued
Navini Networks, Inc.
Step Action
9.
The Pre-Installation
Summary screen
appears. Review the
contents for accuracy.
Click Install to
continue.
10.
Illustration
For your installation and
computer, this screen
may have different
information than what is
shown in the illustration.
The Installing screen
will display as the
application files are
loaded.
11
At the Install Complete
screen, click Done to
close the window.
12.
After clicking Done the
System Settings Change
window appears, asking
if you want to restart
your computer now.
Click Yes.
NOTE: You must restart
your computer at this
point before proceeding.
24
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Troubleshooting
Using Ripwave
Monitor
Ripwave Modem User Guide
To open the Ripwave Monitor software application, click on the
“Start” button and select Programs→Navini Ripwave
Monitor→Ripwave Monitor.
The Ripwave Monitor icon will appear in the toolbox tray of your
computer. Double-click on this icon.
A window with icons and, provided your Modem is on, bar graphs,
will pop up. Notice the bottom right corner of the window shows
the Equipment Identification (EID) for your specific Ripwave
Modem. If you talk with a Service Technician while
troubleshooting, you may be asked for this number.
The icons represent the PC, the connection between the PC and the
Modem, the Modem, the connection between the Modem and the
Base Station, and the Base Station with which the Modem is
communicating.
Computer
Part #40-00097-00 Rev F v1.0
May 21, 2004
Computer to
Ripwave
connection
Ripwave
Modem
Ripwave to
Base Station
Base Station
wireless connection
25
Ripwave Modem User Guide
Troubleshooting Using
Ripwave Monitor,
continued
Navini Networks, Inc.
The Signal Strength and Signal Quality are dynamic bar graphs
that indicate how well your Modem is receiving signals from the
Base Station. To increase the strength and quality of the signal,
change the location of the Ripwave Modem. Try moving it closer
to a window, to a higher location, away from other wireless devices
(microwave ovens, cordless phones), and away from metal objects
(shelves, file cabinets). As the Ripwave Modem is repositioned,
observe the Signal Strength and Signal Quality bar graphs. Position
the Modem for maximum signal strength and quality.
If you make a service call to your Service Provider, the Technician
may ask you to read the numbers to the right of the signal bar
graphs. These will help the Technician to evaluate the best position
for your Ripwave Modem. The Battery Strength bar graph and the
number to the right of it indicate how much charge is left in the
battery. Not all Modems have the battery option. Only some LED
Modems have a battery option. Without a battery in the Modem,
the Battery Strength bar graph and number will be disabled (grayed
out).
If the connection between the PC and the Modem or between the
Modem and the Base Station is interrupted, a, red circle with a
slash
will be positioned over the corresponding icon.
In this example, the cable connecting the computer and Modem is
not operational; the wireless signal between Modem and Base
Station is down; and there is no battery being used.
26
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Troubleshooting Using
Ripwave Monitor,
continued
Ripwave Modem User Guide
To check connectivity to the Service Provider’s network, click the
Advanced button on the Ripwave Monitor window. The Advanced
section of the window appears and displays several strings of
characters representing selected IP-addressable nodes in the
network. These strings of characters (displayed) and the associated
IP addresses (not displayed) are configurable by the Service
Provider on a BTS-per-BTS basis. Note that if the connection
between the Ripwave Modem and the Base Station is down, the
Advanced button will be disabled (grayed out).
The blue question marks on the right side of the Advanced section
indicate that all connections are untested. Now click on the Run
Tests button at the bottom of the window. The PC will attempt to
ping the IP address associated with each one of the character
strings. Each blue question mark will change to either a blue
checkmark or a red circle with a slash mark. A blue checkmark
indicates that the connection to the IP is good. A red circle with a
slash mark indicates there is a problem with that connection to that
IP.
The features of the Advanced and Run Tests buttons are to be used
in conjunction with your Service Provider Technician to resolve
problems. There is no need to use these features unless you are
experiencing problems with the Modem.
Part #40-00097-00 Rev F v1.0
May 21, 2004
27
Ripwave Modem User Guide
Uninstalling
Ripwave
Monitor
28
Navini Networks, Inc.
If for some reason you need to uninstall the Ripwave Monitor
software, e.g., to upgrade your Operating System software, follow
the procedure below.
Step Action
1.
On your computer
screen lower left corner,
click on Start >
Programs > Navini
Navini Monitor >
Uninstall Navini
Monitor. The InstallAnywhere Uninstaller
screen appears. Click
Uninstall.
2.
The screen will cycle
through as the
application files are
uninstalled.
3.
The Uninstall Complete
screen appears when
finished. Click on Quit
to close the Uninstall
screen.
4.
Restart the PC to
complete the uninstall
process. This will ensure
it functions properly
after uninstalling.
Illustration
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Installing Navini
Diagnostics
(NavDiag)
Ripwave Modem User Guide
If your Ripwave Modem has a software release prior to 4.0, you
have the Navini Monitor software and not the Navini Diagnostics.
Step Action
Illustration
1.
Shut down all programs,
including anti-virus
software programs,
before installing the
Navini Diagnostics
software.
2.
Insert the Navini
Diagnositcs Installation
CD into the CD-ROM
drive.
3.
At the bottom left-hand
corner of your screen,
click Start > Run. In
the Run window, enter
e:\setup in the Open
field (where “e”
represents the CD drive
wher you inserted the
installation CD). Click
OK to continue.
4.
The InstallAnywhere
window appears. The
progress bar indicates
that InstallAnywhere has
initialized.
5.
Part #40-00097-00 Rev F v1.0
May 21, 2004
The Navini Diagnostics
Language screen
appears. Select a
language and click OK
to continue.
29
Ripwave Modem User Guide
Installing Navini
Diagnostics, Continued
Navini Networks, Inc.
Step Action
6.
The Navini Diagnostics
Introduction screen
appears. Click Next to
continue.
7.
8.
9.
30
Illustration
The License Agreement
screen appears. Read the
Licensing Agreement.
Select the I Accept
option, and click Next to
continue.
NOTE: If the License
Agreement is not
accepted, you cannot
install the software.
The Choose Install
Folder screen appears.
Enter the name of the
folder where you wish to
install the software.
Click Next to continue.
The default installation
folder provided by the
software is shown in the
illustration.
The Choose Shortcut
Folder screen appears.
Select On the Desktop
and click Next to
continue.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Installing Navini
Diagnostics, Continued
Ripwave Modem User Guide
Step Action
10.
The Pre-Installation
Summary screen
appears. Review the
contents for accuracy.
Click Install to
continue.
11.
12.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Illustration
For your installation and
computer, this screen
may have different
information than what is
shown in the illustration.
The Installing screen
will display as the
application files are
loaded.
At the Install Complete
screen, click Done to
close the window.
31
Ripwave Modem User Guide
Troubleshooting
Using Navini
Diagnostics
(NavDiag)
Navini Networks, Inc.
To open the Navini Diagnostics software application, double-click
on the Navini Diagnostics icon on your desktop.
Navini Diagnostics.lnk
The Connection Status screen will open and display data if the
Modem is in session. The screen refreshes live data every second.
The icons represent the PC, the connection between the PC and the
Modem, the Modem, the connection between the Modem and the
Base Station, and the Base Station to which the Modem is
communicating. Check marks over the connections indicate
working connections.
The Signal Strength and Signal Quality are dynamic bar areas that
indicate how well your Modem is receiving signals from the Base
Station. Green lines indicate a strong signal. Orange lines indicate
a moderately strong signal while red lines indicate a weak signal.
To increase the strength and quality of the signal, change the
location of the Ripwave Modem. Try moving it closer to a window,
to a higher location, away from other wireless devices (microwave
ovens, cordless phones), and away from metal objects (shelves, file
cabinets). As the Ripwave Modem is repositioned, observe the
Signal Strength and Signal Quality bars. Position the Modem for
maximum signal strength and quality.
32
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Troubleshooting Using
Navini Diagnostics,
continued
Ripwave Modem User Guide
The History graphs plot the signal every 10 seconds. Read the
graphs from right to left.
If the connection between the PC and the Modem or between the
Modem and the Base Station is interrupted, a red circle with a slash
question mark is positioned over the corresponding icon.
On the left-hand side of the screen, there are three screen options:
Connection Status, Configuration, and About. The following
screen will appear when you press the Configuration button.
The Configuration screen enables you to update your Modem’s
software if you are so directed by your Service Provider. If you
must update your Modem’s software, your Service Provider will
provide you with instructions regarding what to do.
If you click on About, the following screen will appear.
Part #40-00097-00 Rev F v1.0
May 21, 2004
33
Ripwave Modem User Guide
Navini Networks, Inc.
Troubleshooting Using
Navini Diganostics,
continued
This screen provides the version of the Navini Diagnostics
software currently installed in your computer. It also provides a
web site and telephone number where you can contact your Service
Provider.
34
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Uninstalling
Navini
Diagnostics
Ripwave Modem User Guide
If for some reason you need to uninstall the Navini Diagnostics
software, e.g., to upgrade your Operating System software, follow
the procedure below.
Step Action
1.
On your computer
screen lower left corner,
click on Start >
Programs > Navini
Diagnostics > Uninstall
Navini Diagnostics.
The Install-Anywhere
Uninstaller screen
appears. Click
Uninstall. The screen
will cycle through as the
application files are
uninstalled.
2.
The Uninstall Complete
screen appears when
finished. Click on Quit
to close the Uninstall
screen.
3.
Part #40-00097-00 Rev F v1.0
May 21, 2004
Illustration
Restart the PC to
complete the uninstall
process. This will ensure
it functions properly
after uninstalling.
35
Ripwave Modem User Guide
Installing &
Charging the
Battery
2.4 GHz Battery
Navini Networks, Inc.
The battery pack was an option on former models of Ripwave
Modems. Batteries could be purchased optionally.
If you have a battery, the battery pack is installed in the bottom of
the Ripwave Modem. The battery compartment of the 2.4 GHz
Ripwave Modem varies from the 2.3, 2.5, 2.6, and 3.5 GHz
models. To install and charge or remove the battery pack, follow
the steps based on your model.
Step Action
Squeeze both tabs to
1.
remove or install the
battery pack cover.
Note that the cover is
not used when the
battery pack is installed
in the Modem.
Illustration
Battery Pack Cover tabs
2.
Install the battery pack
into the Ripwave
Modem, ensuring that
the contacts on the
battery pack mate with
the contacts in the
Modem and that both
slides snap down
securely.
3.
To charge the battery,
connect the AC adapter
to the Modem and to an
AC power source
(110/220 VAC, 60/50
Hz). The battery
immediately will begin
charging regardless of
whether the On/Off
switch is on. However,
the pack will charge
faster if the on/off
switch is in the OFF
position.
Battery contacts
Battery
Indicator
..
If the on/off switch is
ON, the light indicator
will be constant yellow.
When fully charged, the
light will go off.
36
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
2.3 GHz, 2.5 GHz,
& 2.6 GHz Battery
Ripwave Modem User Guide
Step Action
1.
Applying light pressure,
push the tab on the
battery pack cover to
remove it from the
bottom of the Modem.
Illustration
Battery Pack Cover tab
2.
Install the battery pack
into the Modem,
ensuring that the
contacts mate and that
both sides snap down
securely.
Reinstall the battery
pack cover on the
Modem.
Battery contacts
3.
To charge the battery,
connect the AC adapter
to the Modem and to an
AC power source. The
battery will begin
charging immediately
regardless of whether
the On/Off switch is on.
However, the pack will
charge faster if the
on/off switch is in the
OFF position.
Battery
Indicator
If the on/off switch is
ON, the light indicator
will be constant yellow.
When fully charged, the
light will go off.
Part #40-00097-00 Rev F v1.0
May 21, 2004
37
Ripwave Modem User Guide
Care &
Maintenance
Navini Networks, Inc.
The Ripwave Modem is designed to give years of trouble-free
service. To ensure operation, read the following care and
maintenance instructions.
Keep the Modem free of dust and moisture. If the Modem gets
wet, use a towel to dry it immediately.
Handle the Modem gently. Dropping it or mishandling it can
cause damage to the plastic shell or the electronic circuitry.
Keep the Modem away from high temperatures. Heat can cause
damage to the plastic shell or the electronic circuitry.
Use only a mild detergent and a soft, damp cloth to clean the
Modem. Do not use any chemicals or abrasives to clean the
plastic shell.
If there is a problem with the Modem, do not attempt to repair
it yourself. Report the problem to your Service Provider.
If you are going to upgrade your Operating System after
loading the Navini monitoring software (Ripwave Monitor or
Navini Diagnostics), you must first uninstall the monitoring
software prior to upgrading the OS. Otherwise, the monitoring
software will not work. See Uninstall instructions in this Guide.
The Ripwave Modem must be left powered ON whenever you
shut down or restart any Windows 98 or ME platforms. If the
Modem is off, a blue screen appears on the monitor. In the
event this happens you will mostly likely have to power cycle
the PC.
Upgrading the
Modem
There are two different ways to upgrade the software that makes
the Modem work. Your Service Provider may perform an over-theair (OTA) upgrade, where the up-to-date software files are
transferred wirelessly from the Base Station to your Modem; or
provide a downloadable web file or CD-ROM with software to be
installed on your PC and used to upgrade the Modem.
The latter method is used only if the Modem was not powered on
during the OTA upgrade process. The OTA upgrade is normally
transparent to the user; in other words, there should be no
noticeable service interruption. The web or CD upgrade comes
with instructions and takes a minimal amount of time to complete.
38
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Ripwave Modem User Guide
ADDENDUM 1: Ripwave™ Modem - PC Troubleshooting
- For Use With All Ripwave Modems, Ripwave Monitor Software, and Navini Diagnostics Software PC Operating Systems
Prior to installing the Ripwave Monitor or Navini Diagnostics software, please check to insure that the
PC Operating System meets the criteria given in the table below. If these criteria are not met,
unpredictable problems may occur as a result of installation. It is recommended that the user have the
latest Windowsc updates installed prior to installing the Ripwave Monitor or Navini Diagnostics
software.
Operating System
Win95
Win98
Win98, 2nd ed.
WinME
Win 2000
Win NT 3.0/4.0
Win XP
Note 1:
Note 2:
Note 3:
Note 4:
Ethernet interface
USB interface
Notes
Supported
Supported
Supported
Supported
Supported
Supported
Supported
Not Supported
Supported
Supported
Supported
Supported
Not Supported
Supported
1, 2
2, 4
2, 4
3, 4
USB was not supported in this software release
Internet Explorer 3.0 or higher is required
Requires Service Pack 1
To load the Ripwave Monitor or Navini Diagnostics software, the user MUST have Administrative
privileges.
USB Interface
The USB Modem allows for a single PC to be connected to the Ripwave Modem via a USB interface, or
multiple PC’s connected via a USB hub. The Modem conforms to USB 1.1 standards. The Ethernet
packets generated by the PC are encapsulated within the USB protocol and transferred to the Modem.
The packets are then sent over-the-air. The USB Modem is fully supported for PC’s using Windows 98,
Windows ME, Windows 2000, and Windows NT 5.0.
To install the Modem using a USB interface, you must connect the Modem to the PC first and insert the
CD that comes with the modem in the package to load the USB “Miniport” driver. After installing the
USB Miniport driver, the PC may or may not need to be restarted, depending upon the type of Operating
System and the particular installation. The system will prompt if a reboot is necessary.
Now install the Ripwave Monitor or Navini Diagnostics software. You must ALWAYS reboot the PC
after installing or uninstalling this software. Failure to do may gravely affect PC operation.
Part #40-00097-00 Rev F v1.0
May 21, 2004
39
Ripwave Modem User Guide
Navini Networks, Inc.
Ethernet Interface
The Ethernet Modem may be connected to a PC via an Ethernet connection. Also, it is possible to
connect multiple PC devices to a single Modem. The multi-PC configuration is transparent to the PC
users and is analogous to a multi-PC configuration on a normal Ethernet LAN. The distinct advantage of
the Ethernet Modem is that it connects to any device that has an Ethernet interface. This makes it ideal
for small businesses that have a mix of devices, such as Unix machines, Apple Computers, etc. IP
addresses can be assigned to the devices dynamically via a DHCP server, or as Fixed IP assignments, or
Point-to-Point Protocol Over Ethernet (PPPoE).
Routers & Hubs
The Ripwave Monitor software will not work if going through a router or if going through some USB or
Ethernet hubs. Doing so may cause Riwpave Monitor software not to operate.
Battery
Older Ripwave Modems gave the user the option of buying an 1800 mA Li-Ion battery. With the optional
battery, the user could be connected to the Internet anytime and anywhere there is RF coverage without
the need for a power outlet. The Modem battery was rated to provide 30 minutes to 90 minutes of use
without recharging (depending on activity).
Configuration Options
Modem connected to
a single computer
(USB or Ethernet)
40
Modem shown as
one of many devices
on a USB hub
Modem providing
access to the Internet
via an Ethernet HUB
Host Computer used
as router to a network
(USB or Ethernet)
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Ripwave Modem User Guide
Results of Correct Navini Monitor Installation
Experienced PC users can check the results of the Navini Ripwave Monitor installation by
looking at the log file that is created during the installation process. The log file is named
“Ripwave_Monitor_InstallLog.log.” It is located under c:\Program Files\Navini Ripwave
Monitor.
------Install Begin: Wed Feb 26 13:30:09 EST 2003
Install End: Wed Feb 26 13:30:29 EST 2003
Created with Zero G's InstallAnywhere 4.5.3 Enterprise Build 1394
Summary
------Installation: Successful.
34 SUCCESSES
0 WARNINGS
0 NONFATAL ERRORS
0 FATAL ERRORS
Action Notes:
None.
Install Log Detail:
Custom Action:
com.navini.iatool.KillMon
Status: SUCCESSFUL
Check Disk Space:
D:\Program Files\Navini Ripwave Monitor
Status: SUCCESSFUL
Additional Notes: NOTE - Required Disk Space: 23,243,991; Free Disk Space: 3,977,043,968
Install Directory:
D:\Program Files\Navini Ripwave Monitor\jre
Status: SUCCESSFUL
Additional Notes: NOTE - Directory already existed
Install Directory:
D:\Program Files\Navini Ripwave Monitor\
Status: SUCCESSFUL
Additional Notes: NOTE - Directory already existed
Install Directory:
D:\Program Files\Navini Ripwave Monitor\UninstallerData\
Status: SUCCESSFUL
Additional Notes: NOTE - Directory already existed
Custom Action:
com.navini.iatool.KillMon
Status: SUCCESSFUL
Install Uninstaller:
Ripwave Monitor (Install All Uninstaller Components)
Status: SUCCESSFUL
Install File:
Install File:
D:\Program Files\Navini Ripwave Monitor\UninstallerData\Uninstall inst.exe
Status: SUCCESSFUL
D:\Program Files\Navini Ripwave Monitor\UninstallerData\Uninstall inst.lax
Status: SUCCESSFUL
Part #40-00097-00 Rev F v1.0
May 21, 2004
41
Ripwave Modem User Guide
Navini Networks, Inc.
Install Directory:
D:\Program Files\Navini Ripwave Monitor\UninstallerData\resource\
Status: SUCCESSFUL
Additional Notes: NOTE - Directory already existed
Install File:
D:\Program Files\Navini Ripwave Monitor\UninstallerData\resource\iawin32.dll
Status: SUCCESSFUL
Install File:
D:\Program Files\Navini Ripwave Monitor\UninstallerData\resource\remove.exe
Status: SUCCESSFUL
Make Registry Entry:
Key:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\Ripwave Monitor, Value Name:
DisplayName, Value Data: Ripwave Monitor
Status: SUCCESSFUL
Make Registry Entry:
Key:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Uninstall\Ripwave Monitor, Value Name:
UninstallString, Value Data: "D:\Program Files\Navini Ripwave Monitor\UninstallerData\Uninstall inst.exe"
Status: SUCCESSFUL
Install Uninstaller:
Ripwave Monitor (Install All Uninstaller Components)
Status: SUCCESSFUL
Install File:
D:\Program Files\Navini Ripwave Monitor\instpro5.exe
Status: SUCCESSFUL
Install File:
D:\Program Files\Navini Ripwave Monitor\NAVMON.exe
Status: SUCCESSFUL
Install File:
D:\Program Files\Navini Ripwave Monitor\navpro5.inf
Status: SUCCESSFUL
Install File:
D:\Program Files\Navini Ripwave Monitor\NAVPRO5.sys
Status: SUCCESSFUL
Registry Entries:
Create the InstallDir Key
Status: SUCCESSFUL
Set Environment Variable: PATH = D:\Program Files\Navini Ripwave Monitor
Status: SUCCESSFUL
Install File:
D:\Program Files\Navini Ripwave Monitor\reboot.exe
Status: SUCCESSFUL
Install Directory:
D:\Documents and Settings\All Users\Start Menu\Programs\
Status: SUCCESSFUL
Additional Notes: NOTE - Directory already existed
Install Directory:
D:\Documents and Settings\All Users\Start Menu\Programs\Navini Ripwave Monitor\
Status: SUCCESSFUL
Additional Notes: NOTE - Directory already existed
Create Shortcut:
Monitor.lnk
D:\Documents and Settings\All Users\Start Menu\Programs\Navini Ripwave Monitor\Ripwave
Status: SUCCESSFUL
42
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Ripwave Modem User Guide
Create Shortcut:
D:\Documents and Settings\All Users\Start Menu\Programs\Navini Ripwave Monitor\Uninstall
Ripwave Monitor.lnk
Status: SUCCESSFUL
Install Directory:
D:\WINDOWS\System32\DRIVERS\
Status: SUCCESSFUL
Additional Notes: NOTE - Directory already existed
Install Directory:
D:\Documents and Settings\All Users\Start Menu\Programs\Startup\
Status: SUCCESSFUL
Additional Notes: NOTE - Directory already existed
Create Shortcut:
D:\Documents and Settings\All Users\Start Menu\Programs\Startup\Ripwave Monitor.lnk
Status: SUCCESSFUL
Install Directory:
D:\WINDOWS\
Status: SUCCESSFUL
Additional Notes: NOTE - Directory already existed
Install File:
D:\WINDOWS\killmon.exe
Status: SUCCESSFUL
Execute Target File:
reboot.exe
Status: SUCCESSFUL
Part #40-00097-00 Rev F v1.0
May 21, 2004
43
Ripwave Modem User Guide
Navini Networks, Inc.
ADDENDUM 2: End User Software License Agreement
---- NOTICE TO USER ---END-USER LICENSE AGREEMENT FOR RIPWAVE SOFTWARE
BY USING THE RIPWAVE SOFTWARE (INCLUDING THE COMPUTER SOFTWARE, THE
ASSOCIATED MEDIA, ANY PRINTED MATERIALS, THE RIPWAVE MODEM, AND ANY
ELECTRONIC OR “ONLINE” DOCUMENTATION) YOU ACCEPT THE TERMS AND
CONDITIONS OF THIS LICENSE AGREEMENT. IF YOU DO NOT AGREE WITH THE TERMS
AND CONDITIONS HEREIN, DO NOT USE THE SOFTWARE, AND PROMPTLY RETURN THE
ENTIRE PACKAGE TO YOUR AUTHORIZED SERVICE PROVIDER.
IN RETURN FOR OUR GRANTING TO YOU A LICENSE TO USE THE SOFTWARE, YOU
AGREE TO THE FOLLOWING TERMS AND CONDITIONS:
IMPORTANT - READ CAREFULLY: This End-User License Agreement ("Agreement") is a legal
agreement between you (either an individual or an entity) and Navini Networks, Inc. for the Ripwave
Software ("SOFTWARE"). The SOFTWARE includes computer software, the associated media, any
printed materials, and any electronic or "online" documentation. Any software provided along with the
SOFTWARE that is associated with a separate end-user license agreement is licensed to you under the
terms of that license agreement. By installing, copying, downloading, accessing, or otherwise using the
SOFTWARE, you agree to be bound by the terms of this AGREEMENT. If you do not agree to the terms
of this AGREEMENT, Navini is unwilling to license the SOFTWARE to you. In such event, you shall
not use or copy the SOFTWARE, and you should promptly contact your Authorized Service Provider
("ASP") for instructions on return of the SOFTWARE and Ripwave Modem. EXCEPT FOR NONDISCLOSURE AGREEMENTS BETWEEN THE PARTIES, THIS IS THE ENTIRE AGREEMENT
BETWEEN THE PARTIES RELATING TO THIS SOFTWARE ANDSUPERSEDES ANY
PURCHASE ORDER, COMMUNICATION, ADVERTISING, OR REPRESENTATION
CONCERNING THE SOFTWARE OR THE RIPWAVE SERVICE. NO CHANGE OR
MODIFICATION OF THIS AGREEMENT WILL BE VALID UNLESS IT IS IN WRITING AND
SIGNED BY NAVINI.
SOFTWARE LICENSE
The SOFTWARE is protected by copyright laws and international copyright treaties, as well as other
intellectual property laws and treaties. The SOFTWARE is licensed, not sold. This Agreement does not
authorize a sale or lease of the SOFTWARE. The term "COMPUTER" shall mean a single computer
system.
44
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Ripwave Modem User Guide
1.
GRANT OF LICENSE. This AGREEMENT grants to you a personal,
non-exclusive, non-transferable license as follows:
1.1
Storage, Installation and Use. Except as otherwise expressly provided in this AGREEMENT, you
will be allowed to install, use, access, run, or otherwise interact with the SOFTWARE on multiple
COMPUTERS. This SOFTWARE may only be used with a Ripwave Digital Modem ("MODEM").
2.
DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS.
2.1
Multiple Processor Version Selection. The CD or diskette(s) on which the SOFTWARE resides
may contain several copies of the SOFTWARE, each of which is compatible with different
microprocessor architectures, such as the x86 architecture or various RISC architectures ("Processor
Version(s)"). You may install and use only one copy of one Processor Version of the SOFTWARE on the
COMPUTER.
2.2
Limitations on Reverse Engineering, Decompiling, and Disassembly. YOU MAY NOT
MODIFY, TRANSLATE, DISASSEMBLE, CREATE DERIVATIVE WORKS, OR REVERSE
ENGINEER THE SOFTWARE OR ANY COPY, IN WHOLE OR IN PART.
2.3
Rental. You may not rent, lease, assign, or lend the SOFTWARE or distribute copies of the
SOFTWARE to others.
2.4
Software Transfer. You may not sell the SOFTWARE. You may not post, distribute or transfer
the SOFTWARE to anyone. You are authorized to use the SOFTWARE on your machine, which means
a machine, all of which is under your complete, direct legal and physical control.
2.5
Termination. This license is effective until terminated. You may terminate this license by
returning the SOFTWARE, the Ripwave Modem and associated hardware and all documentation to your
service provider. Without prejudice to any other rights, NAVINI may terminate your rights under this
AGREEMENT if you fail to comply with the terms and conditions of this AGREEMENT. In such event,
you must return the SOFTWARE and any copies, the Ripwave Modem and associated hardware and all
documentation to your service provider.
2.6
Trademarks. This AGREEMENT does not grant you any rights in connection with any
trademarks or service marks of NAVINI.
Part #40-00097-00 Rev F v1.0
May 21, 2004
45
Ripwave Modem User Guide
Navini Networks, Inc.
2.7
Third Party Intellectual Property. Licensee acknowledges, understands and agrees that the
licensed Software covered by this License Agreement may contain Intellectual Property owned by Third
Parties and duly licensed to NAVINI NETWORKS, INC. Copyright, Patent and other laws protect Third
Party Intellectual Property manufactured with, marketed with, or otherwise bundled with the licensed
Software. Licensee promises to keep such Third Party Intellectual Property in confidence to the benefit
of the Third Party, agrees not to reverse engineer or otherwise decompile Third Party Intellectual
Property, and agrees to stop using, destroy and/or return such Third Party owned Intellectual Property
under the same terms and conditions as the licensed Software as set forth in this License Agreement. The
Third Party is a third party beneficiary under this License Agreement and may independently enforce its
Intellectual Property rights.
2.8
Remote Digital Access. Licensor reserves the right, but is not obligated to digitally access the
Modem and/or the Ripwave Software for the purposes of upgrading and maintaining the software.
3.
UPGRADES. If the SOFTWARE is labeled as an upgrade, you must be properly licensed to use a
product identified by NAVINI as being eligible for the upgrade in order to use the SOFTWARE
("Eligible Software"). SOFTWARE labeled as an upgrade replaces and/or supplements (and may
disable) the Eligible Software. You may use the resulting upgraded product only in accordance with the
terms of this AGREEMENT.
4.
COPYRIGHT. The SOFTWARE is provided with restrictive rights. All title and intellectual
property rights in and to the SOFTWARE (including but not limited to any images, photographs,
animations, video, audio, music, text, and "applets" incorporated into the SOFTWARE), the
accompanying printed materials, and any copies of the SOFTWARE, are owned by NAVINI. All title
and intellectual property rights in and to the content that is not contained in the SOFTWARE but may be
accessed through use of the SOFTWARE and the MODEM is the product of the respective content
owner and may be protected by applicable copyright or other intellectual property laws and treaties. This
AGREEMENT grants you no rights to use such content. Use of any online services that may be accessed
through the SOFTWARE may be governed by the respective terms of use for such services. If this
SOFTWARE contains documentation that is provided only in electronic form, you may print one copy of
such electronic documentation. You may not copy the printed materials accompanying the SOFTWARE.
All rights not specifically granted under this AGREEMENT are reserved by NAVINI.
5.
PRODUCT SUPPORT. Product support for the SOFTWARE is not provided by NAVINI. For
product support, please refer to ASP's support number provided in their documentation.
6.
U.S. GOVERNMENT RESTRICTED RIGHTS. ALL SOFTWARE provided to the U.S.
Government pursuant to solicitations issued on or after December 1, 1995 is provided with the
commercial license rights and restrictions described elsewhere herein. ALL SOFTWARE provided to
the U.S. Government pursuant to solicitations issued prior to December 1, 1995 is provided with
“Restricted Rights” as provided for in FAR, 48 CFR 52.227-14 (June 1987) or DFAR, 48 CFR 252.2277013 (Oct 1988), as applicable.
7.
EXPORT RESTRICTIONS. You agree that you will not directly or indirectly export or re-export
the SOFTWARE (or portions thereof) to any proscribed country. You specifically agree not to export or
46
Part #40-00097-00 Rev F v1.0
May 21, 2004
Navini Networks, Inc.
Ripwave Modem User Guide
re-export the SOFTWARE (i) to any country to which the U.S. has embargoed or restricted the export of
goods or services, which currently include, but are not necessarily limited to, Cuba, Iran, Iraq, Libya,
North Korea, Sudan, and Syria, or to any national of any such country, wherever located, who intends to
transmit or transport the SOFTWARE back to such country; (ii) to any person or entity whom you know
or have reason to know will utilize the SOFTWARE in the design, development, or production of
nuclear, chemical, or biological weapons; or (iii) to any person or entity who has been prohibited from
participating in U.S. export transactions by any federal agency of the U.S. government.
8.
WARRANTY. THE SOFTWARE IS PROVIDED ON AN "AS IS" BASIS WITHOUT
WARRANTIES OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION
ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE,
TITLE, NON-INFRINGEMENT, AND ANY WARRANTY AGAINST LATENT DEFECTS. NAVINI
DOES NOT WARRANT THAT THE OPERATION OF THE SOFTWARE WILL BE
UNINTERRUPTED OR ERROR FREE. YOU ARE SOLELY RESPONSIBLE FOR DETERMINING
WHICH SOFTWARE BEST SUITS YOUR NEEDS, FOR INSTALLING THE SOFTWARE, AND
FOR RESULTS OBTAINED. YOU HAVE THE SOLE RESPONSIBILITY FOR INSPECTING AND
TESTING THE SOFTWARE TO YOUR SATISFACTION BEFORE USING THEM WITH
IMPORTANT DATA OR WITH YOUR COMPUTER. NAVINI MAKES NO WARRANTIES OR
REPRESENTATIONS WHATSOEVER REGARDING ANY GOODS OR SERVICES PROVIDED BY
ANY THIRD PARTIES PURSUANT TO YOUR USE OF THE SOFTWARE AND NAVINI SHALL
NOT BE LIABLE FOR ANY COSTS OR DAMAGES ARISING OUT OF, EITHER DIRECTLY OR
INDIRECTLY, THE ACTIONS OR INACTIONS OF SUCH THIRD PARTY. IN NO EVENT SHALL
NAVINI NETWORKS, INC. OR ANY THIRD PARTY INVOLVED IN THE CREATION,
PRODUCTION, DELIVERY, OR LICENSING OF THE SOFTWARE BE LIABLE TO YOU OR ANY
THIRD PARTY FOR ANY DIRECT, INDIRECT, SPECIAL, GENERAL, PUNITIVE, EXEMPLARY,
AGGRAVATED, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF ADVISED OF THE
POSSIBILITY THEREOF, WHETHER FORESEEABLE OR UNFORESEEABLE, OF ANY KIND
WHATSOEVER, INCLUDING BUT NOT LIMITED TO LOSS OF PROFITS; UNANTICIPATED
BENEFITS OR REVENUE; ANTICIPATED PROFITS; DAMAGES OR COSTS INCURRED AS A
RESULT OF: (i) LOST TIME, DATA, OR USE OF THE SOFTWARE; (ii) HARDWARE FAILURES
FOR ANY REASON; (iii) INCOMPATIBILITY WITH HARDWARE OR OTHER SOFTWARE; (iv)
LOSS OR CLAIMS FROM THIRD PARTIES; OR (v) FROM ANY OTHER CAUSE ARISING OUT
OF USE OF OR INABILITY TO USE THE SOFTWARE, OR CONTRIBUTION OR INDEMNITY IN
RESPECT OF ANY CLAIM RELATED TO THE SOFTWARE. IN ANY EVENT, NAVINI'S
LIABILITY SHALL NOT EXCEED THE ACTUAL PRICE PAID FOR THE LICENSE TO USE THE
SOFTWARE.
Part #40-00097-00 Rev F v1.0
May 21, 2004
47
Ripwave Modem User Guide
Navini Networks, Inc.
SOME JURISDICTIONS DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES, OR ALLOW LIMITATIONS ON HOW LONG A WARRANTY
LASTS, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS, WHICH VARY FROM JURISDICTION TO JURISDICTION.
9.
LAW. This Agreement and each Order shall be construed in accordance with the laws (including
the Uniform Commercial Code) of the State of Texas, without giving effect to principles of conflicts of
laws. Any legal action arising here from will be brought within the state or federal courts located in
Dallas county, Texas, which is agreed by the parties to be a convenient forum. The SOFTWARE User
acknowledges, understands and agrees that this Agreement is written in the English Language and
versions of this Agreement written in any other language is for convenience only, and the SOFTWARE
User expressly waives all “native language” requirements, whether based in local statutory, regulatory or
other law.
END OF AGREEMENT
Copyright © 2001, 2002, 2003, 2004 Navini Networks, Inc.
All rights reserved. Printed in the USA.
Navini Networks is a registered trademark. Internet at the Speed of Thought, Zero-Install, Ripwave, and
Unwired by Navini are trademarks of Navini Networks, Inc. Other product and company names
mentioned herein may be trademarks and/or service marks of their respective owners. Rev. 052302
48
Part #40-00097-00 Rev F v1.0
May 21, 2004

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 48
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:a7bfe9c5-8110-44b0-8c41-a75e5ed16bff
Producer                        : Acrobat Distiller 6.0 (Windows)
Comments                        : Standard Release 1.20
Category                        : Modem
Company                         : Navini Networks
Manager                         : S. Redfoot
Source Modified                 : D:20040705182742
Headline                        : modem
Create Date                     : 2004:07:05 14:01:29-05:00
Creator Tool                    : Acrobat PDFMaker 6.0 for Word
Modify Date                     : 2004:07:05 14:04:09-05:00
Metadata Date                   : 2004:07:05 14:04:09-05:00
Document ID                     : uuid:231c4c57-7d70-4006-8445-b1563d9c31a6
Version ID                      : 47
Format                          : application/pdf
Title                           : Ripwave Modem User Guide
Creator                         : M. Cox
Description                     : modem
Subject                         : end-user; Ripwave; modem; cpe; unit; pc; IAD
Tagged PDF                      : Yes
Author                          : M. Cox
Keywords                        : end-user;, Ripwave;, modem;, cpe;, unit;, pc;, IAD

EXIF Metadata provided by EXIF.tools