Cisco Systems Dial Nms Operating Instructions Dnmsb

2015-01-05

• Preface
  • Purpose
  • Audience
  • Scope
  • Conventions
  • Related Documentation and Sites
    • Technical References and Support
    • Internetworking Solutions Guides
    • Freeware
    • Cisco Product Documentation
  • Cisco Connection Online
  • Documentation CD-ROM
  • Documentation Feedback
  • Acknowledgements
• Overview of Basic SNMP Building Blocks
  • About SNMP
  • What are the Basic Components of SNMP?
  • About Basic SNMP Message Types and Commands
  • What are SNMP MIBs?
  • What is SNMPv1?
    • SNMPv1 and ASN1 Data Types
    • SNMPv1 and SMI-Specific Data Types
    • SNMPv1 Protocol Operations
  • What is SNMPv2?
    • SNMPv2 and SMI
    • SMI Information Modules
    • SNMPv2 Protocol Operations
  • About SNMP Management
  • About SNMP Security
• Network Design for a DialNMSCase Study
  • Introduction to the Case Study
  • Benefits of a Dial NMS
  • Dial NMS Planning Questionnaire
  • Dial NMS Service Definition
  • Network Topology
  • Hardware Requirements
  • Software Requirements
  • Configuration Design Parameters
  • Implementation and Operation Tasks
• Dial MIBs and OIDs Used in the Case Study
• Task 1—Enabling SNMP in a Cisco IOS Device
  • About Enabling SNMP
    • Enabling SNMP
• Task 2— Exploring SNMP Capabilities by Using UCD-SNMP
  • About Using UCD-SNMP
    • Installing UCD-SNMP and Downloading Cisco MIBs
    • Exploring SNMP MIBs for Dial Networks
  • About SNMP Commander
    • Setting Up SNMP Commander
• Task 3—Using MRTG to Monitor and Graph Traffic Loads
  • About MRTG
  • About Selecting Dial OIDs
  • How to Inspect and Interpret Data
    • Creating and Editing a Configuration File
    • Sending MRTG Graphs to a Web Server
• Task 4—Using Syslog, NTP, and Modem Call Records to Isolate and Troubleshoot Faults
  • About Syslog
  • About NTP
  • About Modem Call Records
    • Enabling NTP on a Cisco IOS Device
    • Setting Up an NTP Client
    • Troubleshooting the NTP Client
    • Enabling Syslog and Modem Call Records in the Cisco IOS Software
    • Configuring the Syslog Daemon
    • Inspecting Syslog Messages in the Log File
• Task 5—Setting Up a Web Portal forthe DialNMS
  • About a Web Portal
    • Building a Device Linker Web Page
    • Troubleshooting a Cisco 2511 Console Connection
  • About HTTP Access to the CLI
    • Using HTTP to Access CLI Commands
• Task 6—Managing IP Addresses by Using DNS
  • About Managing IP Addresses
    • Using Cisco Network Registrar CLI Commands
    • Using a Batch File to Make Changes to a DNS Configuration
    • Creating a Primary Forward Zone
    • Creating an IP Tracker Web Page
  • How to Create a Reverse DNS Zone
• Task 7—Using HP OpenView to Create the SNMP Framework
  • About HP OpenView
    • Verifying the SNMP Configuration
  • About SNMP Demand Polls
    • Performing an SNMP Demand Poll
    • Testing SNMP Get Requests
    • Troubleshooting SNMP and a Demand Poll
    • Verifying that SNMP Traps Are Received
    • Unmanaging the Dial Ports
    • Creating and Adjusting Maps
  • About Discovery Filters
    • Setting Up and Editing a Discovery Filter
    • Using the HPOV CLI to Enter a Device into the Database
• Task 8—Using CiscoWorks 2000 Resource Manager Essentials
  • About CiscoWorks 2000 RME
    • Importing Devices from HPOV and Populating the Databases
    • Verifying that Device Polling is Turned On
    • Polling the Devices
    • Backing up Cisco IOS Configurations
    • Using CiscoView