Cisco Systems VP1900XX PCS GSM Base Station User Manual

Cisco Systems Inc PCS GSM Base Station

Contents

User Manual

-HW&HOO,QF8VHUV0DQXDO%HWD9LSHU%DVH
JetCell ConfidentialThe information contained in this document is the property of JetCell, Inc. Except asspecifically authorized in writing by JetCell, the holder of this document shall keep theinformation contained herein confidential and protect it from disclosure and dissemina-tion to third parties in whole or in part and use same for evaluation purposes only. Cert-tain inventions described herein may be the subject of pending U.S. and internationalpatent applications.This document, whether published or unpublished, is protected as a copyrighted workand may not be copied, adapted, displayed or modified without written consent of Jet-Cell, Inc. Report infringements to infringement@jetcell.com.The contents of this document are provided for information purposes only and are sub-ject to modification by JetCell, Inc. without notice. No representation or warranty ismade as to the completeness or accuracy of the information contained herein, includingbut not limited to information concerning the suitability or performance of the product orapplication, merchantability or fitness for any particular purpose.The following are trademarks of JetCell, Inc.: GoIP, RAP, SmartCell, SureTrack, V7M,V7X, ViperBase, ViperCell, ViperWatch.ViperBase Users ManualBeta Release 0.1© Copyright 1999 JetCell Incorporated. All rights reserved.
-HW&HOO,QF7DEOHRI&RQWHQWVInstalling and Configuring ViperBase .......................................................... 1-1Running ViperBase .................................................................................... 1-1Navigating ViperBase ........................................................................ 1-2Using ViperBase Configuration Management .............................................. 1-2The General Dialog Box ..................................................................... 1-3The Gateway List Dialog Box ............................................................. 1-4ViperBase Subscriber Management ............................................................ 1-4The IP Phone List Dialog Box............................................................. 1-5The Mobile List Dialog Box ................................................................ 1-6The Subscriber Detail Information Dialog Box ..................................... 1-7Sending a Text Message with SMS-CB ....................................................... 1-7Schedule a New Message .................................................................. 1-8Delete a Scheduled Message ............................................................. 1-9Query Scheduled Messages ............................................................... 1-9Change a Schedule Message ............................................................. 1-9Sending Feedback to JetCell, Inc. .............................................................. 1-9
-HW&HOO,QF  9LSHU%DVH2SHUDWLRQViperBase performs the H.323 Gatekeeper required by the ViperCell network. ViperBase:•Runs on a Windows NT server•Is configured and managed from the HTML-based ViperWatch OA&M sys-tem.•Is compatible with Microsoft Internet Explorer 4.0 or later and Netscape Navigator 4.0 or laterIn the IP Address area of the web browser, type the IP address of the active Viper-Base. After a short delay, the Registered ViperCells dialog box opens.The Registered Viper Cells dialog box is divided into four fields:•The ViperCell Name field identifies the active ViperCell•The Cell ID identifies the identifying number assigned to the ViperCell•Click on a ViperCell IP address to be transferred to the System Informa-tion dialog box of the ViperCell
-•The Number of Active Mobiles shows how many MS’s are active at the time the dialog box is accessed.At the bottom of the dialog box, click Recall to update the Registered ViperCells dialog box.The ViperBase display is divided into three frames.•The top frame contains information about the ViperBase being viewed•The frame at the left side of the display contains the topic headings of the different ViperBase dialog boxes•The central and largest frame is the specific ViperBase dialog box.In the left frame, click on a topic heading to open the topic in the main window.ViperBase Configuration Management uses interactive Java.In the left frame, click on Configuration Management to load the Java Applet. After a pause of up to 30 seconds while the applet loads, the General dialog box appears. Configuration Management consists of primary dialog boxes:•The General dialog box provides information about ViperBase network connectivity•The Gateway List dialog box displays a list of all active H.323 Gateways that are part of the ViperCell network
In the left frame, click on the ViperBase Configuration Management topic heading to open the General dialog box.The General dialog box contains configuration information for the ViperBase.•Click Get to refresh the displayed information.•Click Set to write from the General dialog box to the ViperBase.
-The Gateway List dialog box shows all H.323 Gateways active in the ViperCell network.•Click Get to refresh the display•Click Set to transfer changes from the Gateway List dialog box to the ViperBaseIn the left frame, click on Subscriber Management to add, modify, and remove ViperCell subscriber information. ViperBase Subscriber Management consists of three dialog boxes:•The IP Phone List dialog box•The Mobile List dialog box•The Subscriber Detail Information dialog boxEach of these dialog boxes is described in the following sections.
The IP Phone list dialog box lists the Internet Protocol (IP) phones that can access the ViperCell network.During Beta trials, the IP Phone list will operate in read-only mode.
-Use the Mobile List dialog box to display a summary of users that are installed in the ViperCell’s Local Users Database (LUDB).Double-click on a list item to display details about that Mobile Station (MS).
The Subscriber Detail Information dialog box to configure a specific Mobile Station (MS).•Click New to display an empty Subscriber Detail dialog box. The MS set-tings in a new Detail dialog box are reset to their default values.•Click Save to transfer updated subscriber information from the Detail dia-log box to the ViperBase.•Click Cancel to close the Detail dialog box and return to the Mobile List dialog box.In the left frame, click on SMS-CB to open the Short Message Service Cell Broad-cast (SMS-CB) dialog box. In the left frame, click on the triangular button next to SMS-CB to open the four SMS-CB topic headings:•Schedule a New Message•Delete a Scheduled Message (Not available)•Query Scheduled Messages (Not available)•Change a Schedule Message (Not available)Each of these are described in the following sections.
-In the left frame, click on Schedule a New Message. The new message dialog box opens.The new SMS-CB Message dialog box includes the following parameters:•Geographical Scope of the message:•PLMN Wide•Location Area wide•Cell Wide•Display Mode:•This option is not yet implemented.•A 4-digit Message Identifier•Language Option for the message.•Broadcast Start Time of the message•Broadcast Duration•The Message to be sentClick Send to transfer the message to the ViperBase. The ViperBase sends the message to all MS’s in the chosen geographical scope.
This feature is not yet implemented.This feature is not yet implemented.This feature is not yet implemented.In the left frame, click Feedback to open the Feedback dialog box.Use the Feedback form to report problems or request enhancements from JetCell, Inc.•Click Submit Comments to transfer the form to JetCell, Inc.•Click Clear Form to reset the feedback dialog box to the default state
-

Navigation menu