Cisco Systems XSCLCR15 4.9 GHz WMIC Mini PCI Module User Manual MRhBookb

Cisco Systems Inc 4.9 GHz WMIC Mini PCI Module MRhBookb

OEM User Manual 1

Final Draft - Cisco ConfidentialCorporate HeadquartersCisco Systems, Inc.170 West Tasman DriveSan Jose, CA 95134-1706 USAhttp://www.cisco.comTel: 408 526-4000800 553-NETS (6387)Fax: 408 526-4100Cisco 3200 Series Mobile Access Router Hardware ReferenceJuly 14, 2005Customer Order Number: 85-4201-06Text Part Number: OL-5816-04
Final Draft - Cisco ConfidentialTHE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California. NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.Cisco 3200 Series Mobile Access Router Hardware ReferenceCopyright © 2005, Cisco Systems, Inc.All rights reserved.CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet, ASIST, BPX, Catalyst, CCDA, CCDP, CCIE, CCNA, CCNP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, the Cisco IOS logo, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Empowering the Internet Generation, Enterprise/Solver, EtherChannel, EtherSwitch, Fast Step, GigaStack, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream, MGX, MICA, the Networkers logo, Networking Academy, Network Registrar, Packet, PIX, Post-Routing, Pre-Routing, RateMUX, Registrar, ScriptShare, SlideCast, SMARTnet, StrataView Plus, Stratm, SwitchProbe, TeleRouter, The Fastest Way to Increase Your Internet Quotient, TransPath, and VCO are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries. All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0401R)
iiiCisco 3200 Series Mobile Access Router Hardware ReferenceOL-5816-04CONTENTSIntroduction to the Cisco 3200 Series Mobile Access Router Cards iAudience and Scope iiRelated Documentation iiObtaining Documentation ivCisco.com ivOrdering Documentation ivDocumentation Feedback vTools and Web Sites vObtaining Additional Publications and Information viCisco 3200 Documentation CD viiSystem Requirements for the CD viiPrinting Documents from the CD viiiConventions viiiObtaining Technical Assistance xiiCisco Technical Support Website xiiSubmitting a Service Request xiiiDefinitions of Service Request Severity xiiiCHAPTER 1Mobile Access Router Card (MARC) 1-1MARC Component Systems 1-2MARC Router Signals 1-210/100 Fast Ethernet Signals on the MARC 1-3Console, Auxiliary, LED Signals, and Power 1-4MARC Power Requirements 1-6CHAPTER 2Fast Ethernet Switch Mobile Interface Card (FESMIC) 2-1Auto-Negotiation and Auto-MDI/MDIX 2-2MAC Address Allocation 2-2FESMIC Component Systems 2-3Signals for the FESMIC 2-410/100 Fast Ethernet Signals on the FESMIC 2-4FESMIC LED Signals 2-5FESMIC Rotary Switch Positions 2-7
ContentsivCisco 3200 Series Mobile Access Router Hardware ReferenceOL-5816-04CHAPTER 3Serial Mobile Interface Card (SMIC) 3-1SMIC Component Systems 3-2Signals for the SMIC 3-3Serial Cable Length 3-3SMIC LED Signals 3-44-Port SMIC Rotary Switch Positions 3-4CHAPTER 4Wireless Mobile Interface Card (WMIC) 4-1WMIC Component Systems 4-1Signals for the WMIC 4-210/100 Fast Ethernet Signals on the WMIC 4-3WMIC Multifunction Header Signals 4-4LED Behavior 4-5Antenna Connector 4-6Key Features 4-62.4-GHz (802.11b/g) Features 4-64.9-GHz (US Only, Public Safety) Features 4-7Throughput 4-8Modulation 4-8Receive Sensitivity 4-82.4-GHz (802.11b/g) WMIC and the 4.9-GHz (US Only, Public Safety) Features 4-9MAC Address Allocation 4-10Power Requirements 4-10Related Documentation 4-10
iCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Introduction to the Cisco 3200 Series Mobile Access Router CardsThe Cisco 3200 Series Mobile Access Routers include a combination of mobile interface cards. The following cards are available from Cisco:•Mobile Access Router Card (MARC)•Fast Ethernet Switch Mobile Interface Cards (FESMICs)•Serial Mobile Interface Cards (SMICs)•Wireless Mobile Interface Cards (WMICs)A completed router includes a third-party power source, cables, and an enclosure, that are assembled and installed by your system integrator. This document describes the cards provided by Cisco Systems, Inc. used to assemble Cisco 3200 Series Mobile Access Routers. For information regarding the specific hardware configuration of your router, contact your vendor.The following chapters provide the information that you need to understand the physical components of a completed Cisco 3200 Series Mobile Access Router. It is not intended as assembly or repair instructions. Chapter 1, “Mobile Access Router Card (MARC),” describes the Mobile Access Router Card (MARC) layout, ports, and buses.Chapter 2, “Fast Ethernet Switch Mobile Interface Card (FESMIC),” describes the Fast Ethernet Switch Mobile Interface Cards (FESMICs) layout, ports, and buses.
iiCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 3, “Serial Mobile Interface Card (SMIC),” describes the Serial Mobile Interface Cards (SMICs) layout, ports, and buses.Chapter 4, “Wireless Mobile Interface Card (WMIC),” describes the Wireless Mobile Interface Cards (WMICs) layout, ports, and buses.Audience and ScopeThe audience for this document is the system administrator (SA), system integrator (SI), and system engineer (SE). They are experts, with networking industry training and experience. We assume that users are familiar with the terminology and concepts of the PC-104, IOS, and Mobile IP networking. The SA, SI, or SE uses this document to understand how the router hardware is connected to peripheral devices and to perform minor troubleshooting on the cards. Although they might not be specifically identified as SAs, SIs, or SEs, all users of this documentation are assumed to have comparable skills and knowledge.Related DocumentationYou can access these documents on the Documentation page on Cisco Connection Online (CCO) at www.cisco.com. The following documentation is available at the http://www.cisco.com/en/US/products/hw/routers/ps272/tsd_products_support_series_home.htmlURL:•Release Notes for the Cisco 3200 Series Mobile Access Routers (78-13975)—Provides information on accessing documentation and technical assistance for the Cisco 3200 Series Mobile Access Router.•Cisco 3200 Series Wireless MIC Software Configuration Guide1 (OL-7734)—This document. It provides example procedures for using the IOS commands to configure Wireless Mobile Interface Cards (WMICs).•Configuration Guide for the Cisco 3200 Series Mobile Access Router1—Example procedures for using the IOS commands to configure the Mobile Access Router Card (MARC) in Cisco 3200 Series routers.
iiiCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04•Cisco 3200 Series Mobile Access Router Hardware Reference1 (OL-5816)—descriptions of the Cisco MIC I/O cards found in Cisco 3200 Series routers.•Cisco 3200 Series Mobile Access Router Reference Sell Document1 (OL-3880)—An overview of the reference sell program and components for the Cisco 3200 Series router.•Regulatory Compliance and Safety Information for the Cisco 3200 Mobile Access Router (78-16930)—Regulatory compliance and safety information.1. Also available on the platform-specific CD-ROM.The Release Notes for the Cisco 3250 Mobile Router lists the enhancements to and caveats for Cisco IOS releases as they relate to the Cisco 3200 Series router can be found at:http://www.cisco.com/en/US/products/sw/iosswrel/products_ios_cisco_ios_software_releases.html orhttp://www.cisco.com/en/US/products/sw/iosswrel/ps5012/ps4629/index.htmlFor information about using Cisco IOS software to configure SNMP, refer to the following documents:•The “Configuring SNMP Support” chapter of the Cisco IOS Configuration Fundamentals Configuration Guide, Release 12.2 •The “SNMP Commands” chapter of the Cisco IOS Configuration Fundamentals Command Reference, Release 12.2 For information about using Cisco IOS software to configure SNMP MIB features, refer to the appropriate documentation for your network management system.For information on configuring Mobile IP using Cisco IOS software, refer to the following documents:•The “Configuring Mobile IP” chapter of the Cisco IOS IP Configuration Guide, Release 12.2 •The “Mobile IP Commands” chapter of the Cisco IOS IP Command Reference, Volume 1 of 3: Addressing and Services, Release 12.2 Related documents from the Cisco TAC Web pages include:•Antenna Cabling http://www.cisco.com/warp/public/102/wlan/antcable.html
ivCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Obtaining DocumentationCisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.Cisco.comYou can access the Cisco website at this URL:http://www.cisco.comYou can access international Cisco websites at this URL:http://www.cisco.com/public/countries_languages.shtmlOrdering DocumentationYou can order Cisco documentation in these ways:•Registered Cisco.com users (Cisco direct customers) can order Cisco product documentation from the Ordering tool:http://www.cisco.com/en/US/partner/ordering/index.shtml•Nonregistered Cisco.com users can order documentation through a local account representative by calling Cisco Systems Corporate Headquarters (California, USA) at 408 526-7208 or, elsewhere in North America, by calling 1 800 553-NETS (6387).
vCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Documentation FeedbackYou can send comments about technical documentation to bug-doc@cisco.com.You can submit comments by using the response card (if present) behind the front cover of your document or by writing to the following address:Cisco SystemsAttn: Customer Document Ordering170 West Tasman DriveSan Jose, CA 95134-9883We appreciate your comments.Tools and Web SitesIf you are registered Cisco Direct Customer, you can access the following web sites:IOS Command Lookup—A search engine dedicated to finding information on Cisco IOS commands in the Cisco IOS Command Reference, Cisco IOS Configuration Guide, Catalyst Command Reference, and PIX Firewall Command Reference.http://www.cisco.com/cgi-bin/Support/Cmdlookup/home.plBug Toolkit—Searches for known bugs based on software version, feature set and keywords. The resulting matrix shows when each bug was integrated, or fixed if applicable.http://www.cisco.com/cgi-bin/Support/Bugtool/launch_bugtool.plFeature Navigator—Locates the Cisco IOS Software release based on the features you want to run on your network.http://tools.cisco.com/ITDIT/CFN/jsp/index.jspObtain information on compatibility between hardware products and software releases at the following public URL:http://tools.cisco.com/Support/Fusion/FusionHome.do
viCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Obtaining Additional Publications and InformationInformation about Cisco products, technologies, and network solutions is available from various online and printed sources.•Cisco Marketplace provides a variety of Cisco books, reference guides, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:http://www.cisco.com/go/marketplace/•The Cisco Product Catalog describes the networking products offered by Cisco Systems, as well as ordering and customer support services. Access the Cisco Product Catalog at this URL:http://cisco.com/univercd/cc/td/doc/pcat/•Cisco Press publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL:http://www.ciscopress.com•Packet magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL:http://www.cisco.com/packet•iQ Magazine is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL:http://www.cisco.com/go/iqmagazine
viiCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04•Internet Protocol Journal is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL:http://www.cisco.com/ipj•World-class networking training is available from Cisco. You can view current offerings at this URL:http://www.cisco.com/en/US/learning/index.htmlCisco 3200 Documentation CD The Cisco 3200 Series Router Documentation CD contains the technical publications for the Cisco 3200 Series Mobile Access Router. To view the documentation requires Acrobat Reader 4.0 or higher.After the CD is inserted in the CD ROM drive and recognized by your PC, do the following:Step 1 Access the root directory CD drive.Step 2 Double click the StartHere.htm file.System Requirements for the CDProcessor Pentium 150 MHz or faster recommendedPC Operating System Microsoft Windows 95 Microsoft Windows 98 Microsoft Windows MEMicrosoft Windows XPMicrosoft Windows NT 4.0 Microsoft Windows 2000Memory 64-MB DRAM
viiiCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Printing Documents from the CDTo print a document: Step 1 Display the document in Acrobat.Step 2 Click the Printer icon on the Acrobat toolbar. The Windows Print Dialog box appears.Step 3 Select your default printer, and click OK.ConventionsThis publication uses these conventions to convey instructions and information:Command descriptions use these conventions:•Commands and keywords are in boldface text.•Arguments for which you supply values are in italic.•Square brackets ([ ]) mean optional elements.•Braces ({ }) group required choices, and vertical bars ( | ) separate the alternative elements.•Braces and vertical bars within square brackets ([{ | }]) mean a required choice within an optional element.Drives 4x CD-ROM driveMonitor Color monitor capable of 800 x 600 pixel resolutionSoftware Adobe Acrobat Reader 4.0 or laterProcessor Pentium 150 MHz or faster recommended
ixCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Interactive examples use these conventions:•Terminal sessions and system displays are in screen font.•Information you enter is in boldface screen font.•Nonprinting characters, such as passwords or tabs, are in angle brackets (< >).Notes, cautions, and timesavers use these conventions and symbols:Tip Means the following will help you solve a problem. The tips information might not be troubleshooting or even an action, but could be useful information.Note Means reader take note. Notes contain helpful suggestions or references to materials not contained in this manual.Caution Means reader be careful. In this situation, you might do something that could result equipment damage or loss of data.WarningThis warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. (To see translations of the warnings that appear in this publication, refer to the appendix “Translated Safety Warnings.”)WaarschuwingDit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico’s en dient u op de hoogte te zijn van standaard maatregelen om ongelukken te voorkomen. (Voor vertalingen van de waarschuwingen die in deze publicatie verschijnen, kunt u het aanhangsel “Translated Safety Warnings” (Vertalingen van veiligheidsvoorschriften) raadplegen.)
xCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04VaroitusTämä varoitusmerkki merkitsee vaaraa. Olet tilanteessa, joka voi johtaa ruumiinvammaan. Ennen kuin työskentelet minkään laitteiston parissa, ota selvää sähkökytkentöihin liittyvistä vaaroista ja tavanomaisista onnettomuuksien ehkäisykeinoista. (Tässä julkaisussa esiintyvien varoitusten käännökset löydät liitteestä "Translated Safety Warnings" (käännetyt turvallisuutta koskevat varoitukset).)AttentionCe symbole d’avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures. Avant d’accéder à cet équipement, soyez conscient des dangers posés par les circuits électriques et familiarisez-vous avec les procédures courantes de prévention des accidents. Pour obtenir les traductions des mises en garde figurant dans cette publication, veuillez consulter l’annexe intitulée « Translated Safety Warnings » (Traduction des avis de sécurité).WarnungDieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu einer Körperverletzung führen könnte. Bevor Sie mit der Arbeit an irgendeinem Gerät beginnen, seien Sie sich der mit elektrischen Stromkreisen verbundenen Gefahren und der Standardpraktiken zur Vermeidung von Unfällen bewußt. (Übersetzungen der in dieser Veröffentlichung enthaltenen Warnhinweise finden Sie im Anhang mit dem Titel “Translated Safety Warnings” (Übersetzung der Warnhinweise).)AvvertenzaQuesto simbolo di avvertenza indica un pericolo. Si è in una situazione che può causare infortuni. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riportate in questa pubblicazione si trova nell’appendice, “Translated Safety Warnings” (Traduzione delle avvertenze di sicurezza).AdvarselDette varselsymbolet betyr fare. Du befinner deg i en situasjon som kan føre til personskade. Før du utfører arbeid på utstyr, må du være oppmerksom på de faremomentene som elektriske kretser innebærer, samt gjøre deg kjent med vanlig praksis når det gjelder å unngå ulykker. (Hvis du vil se oversettelser av de advarslene som finnes i denne publikasjonen, kan du se i vedlegget "Translated Safety Warnings" [Oversatte sikkerhetsadvarsler].)
xiCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04AvisoEste símbolo de aviso indica perigo. Encontra-se numa situação que lhe poderá causar danos fisicos. Antes de começar a trabalhar com qualquer equipamento, familiarize-se com os perigos relacionados com circuitos eléctricos, e com quaisquer práticas comuns que possam prevenir possíveis acidentes. (Para ver as traduções dos avisos que constam desta publicação, consulte o apêndice “Translated Safety Warnings” - “Traduções dos Avisos de Segurança”).¡Advertencia!Este símbolo de aviso significa peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considerar los riesgos que entraña la corriente eléctrica y familiarizarse con los procedimientos estándar de prevención de accidentes. (Para ver traducciones de las advertencias que aparecen en esta publicación, consultar el apéndice titulado “Translated Safety Warnings.”)Varning!Denna varningssymbol signalerar fara. Du befinner dig i en situation som kan leda till personskada. Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanligt förfarande för att förebygga skador. (Se förklaringar av de varningar som förekommer i denna publikation i appendix "Translated Safety Warnings" [Översatta säkerhetsvarningar].)
xiiCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Obtaining Technical AssistanceFor all customers, partners, resellers, and distributors who hold valid Cisco service contracts, Cisco Technical Support provides 24-hour-a-day, award-winning technical assistance. The Cisco Technical Support Website on Cisco.com features extensive online support resources. In addition, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not hold a valid Cisco service contract, contact your reseller.Cisco Technical Support WebsiteThe Cisco Technical Support Website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, 365 days a year, at this URL:http://www.cisco.com/techsupportAccess to all tools on the Cisco Technical Support Website requires a Cisco.com user ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL:http://tools.cisco.com/RPF/register/register.doNote Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support Website by clicking the To ols & Resources link under Documentation & Tools. Choose Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under Alerts & RMAs. The CPI tool offers three search options: by product ID or model name; by tree view; or for certain products, by copying and pasting show command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call.
xiiiCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Submitting a Service RequestUsing the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco TAC engineer. The TAC Service Request Tool is located at this URL:http://www.cisco.com/techsupport/servicerequestFor S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco TAC engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.To open a service request by telephone, use one of the following numbers:Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)EMEA: +32 2 704 55 55USA: 1 800 553-2447For a complete list of Cisco TAC contacts, go to this URL:http://www.cisco.com/techsupport/contactsDefinitions of Service Request SeverityTo ensure that all service requests are reported in a standard format, Cisco has established severity definitions.Severity 1 (S1)—Your network is “down,” or there is a critical impact to your business operations. You and Cisco will commit all necessary resources around the clock to resolve the situation. Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operation are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.
xivCisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Severity 3 (S3)—Operational performance of your network is impaired, but most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.
CHAPTER 1-1Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-041Mobile Access Router Card (MARC) The Mobile Access Router Card (MARC) is one component of the Cisco 3200 Series Mobile Access Router. It includes the host processor, memory, and headers for the 10/100 Fast Ethernet, console, and auxiliary signals for the router. Additional components provide power and link interfaces to the MARC. For example, the 4-port Serial Mobile Interface Card provides up to 4 smart serial interfaces. The exact configuration of your router will vary, depending on how it was configured by your vendor.Note This section provides basic information regarding the MARC hardware for the purpose of performing simple troubleshooting, such as reconnecting a loose cable. To solve more difficult problems, please contact your vendor.The key features of the MARC include the following:•MPC8250 processor running 210-MHz at the CPU core, 150-MHz at the CPM core, and 60-MHz on the Motorola 60x bus•32 MB of Flash memory•128 MB synchronous DRAM•10/100 Fast Ethernet, full-duplex connection with auto negotiation•Console connection with hardware/software flow control•Asynchronous, RS-232 serial connection with a 5 V auxiliary power supply for Global Positioning System (GPS) and auxiliary (AUX) devices•A 32-bit PCI bus, version 2.1 running at 25-MHz•Supports zeroization when this featured is configured on the router.Caution Zeroization is a feature that erases all potentially sensitive information from the router. Zeroization is configured through the CLI and activated through an actuator that must be attached to the AUX port, such as a push button. Zeroization is disabled by default on the Cisco 3200 Series router. When Zeroization is not configured on the router, the AUX port functions as a modem port or a terminal port. When declassification is enabled through the CLI, we recommend that you do not use the AUX port for any other function than declassification. This is because there is no way for the router to reliably determine if a device attached to the AUX port is an actuator; therefore, any device attached to the AUX port could potentially trigger declassification.
1-2Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 1 Mobile Access Router Card (MARC)MARC Component SystemsMARC Component SystemsThe industry-standard architecture (ISA) buses and peripheral component interconnect (PCI) buses on the Cisco 3200 Series Mobile Access Router cards provide power to the components on the cards. Both buses comply with the PC/104-Plus standard. The ISA bus allows PC/104-Plus ISA signals to pass through the card bus, but the Cisco cards do not use any of the signals. The PCI bus signals allow the Cisco cards to communicate. Non-Cisco cards cannot communicate with the Cisco 3200 Series Mobile Access Router cards over the PCI bus. Caution If you add non-Cisco cards that generates signals on the PCI bus, the router might shut down. Please do not add non-Cisco cards that generate signals on the PCI bus.Figure 1-1 shows the MARC header and bus locations.Figure 1-1 MARC Header and Bus LocationsNote The PC/104-Plus standard requires that the PCI Bus and the ISA bus utilize keying features in the standard stacking headers to guarantee proper module installation. On the PCI bus, pin D30 is removed and the D30 opening plugged. On the ISA bus, pin C19 and B10 are removed, and the C19 and B10 openings are plugged. MARC Router SignalsCisco 3200 Series router cards do not support any ISA bus signals. The PCI bus connector supports communication between Cisco 3200 Series Mobile Access Router cards. Note Non-Cisco MIC cards cannot use PCI signals. The use of PCI signals by non-Cisco cards causes unpredictable results. You cannot add 3rd-party devices that might attempt to communicate with the SMIC through the ISA or PCI bus. 1PCI Bus 2ISA Bus3Ethernet Header 4Multifunction Header745181 243
1-3Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 1 Mobile Access Router Card (MARC)MARC Component SystemsThe signals are delivered through the shared, 34-pin multifunction header and the 10-pin Ethernet header. LED signals and 5 V of power are also provided through the shared, 34-pin multifunction header. 10/100 Fast Ethernet Signals on the MARCThere is one fixed 10/100 Fast Ethernet port on the MARC. A Cisco router identifies a 10/100 Fast Ethernet interface address by its slot number and port number, in the format slot/port. The slot/port address of a Fast Ethernet interface on the MARC is 0/0.The 10/100 Fast Ethernet port signals are in compliance with IEEE 802.3. They are provided through the 10-pin Ethernet header, which supports the following:•Auto-negotiation and parallel detection MII interface with extended register capability for 10/100BASE-TX connection•Full-duplex and half-duplex modes •3.3V operation low power consumption (300 mW typical)•Low-power sleep mode•10BASE-T and 100BASE-TX using a single Ethernet connection•Robust baseline wander correction performance •100BASE-FX fiber optic capabilities•Standard carrier signal multiple access collision detect (CSMA/CD) or full-duplex operation •Integrated, programmable LED driversFigure 1-2 shows the 10-pin 10/100 Fast Ethernet header pin locations. Figure 1-2 MARC Ethernet Header Pin LocationsTable 1-1 describes the pin assignments shown in Figure 1-2.7452116273849510Board edge Board edgeTable 1-1 MARC Ethernet Header Pin AssignmentsPin Signal Description1 TX+ Transmit Positive6 TX- Transmit Negative2 RX+ Receiving Positive7 Unused Terminated3 Unused Terminated8 RX- Receiving Negative
1-4Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 1 Mobile Access Router Card (MARC)MARC Component SystemsThe FastEthernet 0/0 port on the MARC is a 10/100 Fast Ethernet router port. The FastEthernet ports on the 4-port FESMIC and the 2-port FESMIC are 10/100 Fast Ethernet switch ports. The routing features supported on the MARC cannot be configured on the FESMIC ports.Console, Auxiliary, LED Signals, and PowerFigure 1-3 shows the 34-pin multifunction header that provides console, AUX and GPS connectivity. A small footprint +3.3V/+12V dual RS-232 transceiver drives the RS-232 lines. It supports full modem control signals DTR, CD, RTS, and CTS. The transceiver is connected directly to SMC-1 on the MPC8250. The serial baud rates can be between 9,600 to 115,000bps.The same +3.3V/+12V dual RS232 transceiver—Maxim’s MAX3209E—drives the RS-232 lines. It supports full modem control signals DTR, CD, RTS, and CTS. The transceiver is connected directly to SCC-1 on the MPC8250. The serial baud rates can be between 9,600 and 115,000bps. Figure 1-3 MARC Multifunction Header Pin LocationsConsole ConnectionsYou can configure the console interface by using IOS command line interface (CLI) commands. The console interface and the AUX port can be accessed simultaneously. For example, you can connect a terminal to the console interface and an external modem or a GPS to the AUX port.The console port signals are provided through the multifunction header:•Asynchronous serial DCE •1.2 Kbps, 2.4 Kbps, 4.8 Kbps, 9.6 Kbps, 19.2 Kbps, 38.4 Kbps, 57.6 Kbps, and 115.2 Kbps baud rates•Support full modem control DTR, DSR, RTS, and CTS signals4 Unused Terminated9 Unused Terminated5 Reserved Do not use10 Reserved Do not useTable 1-1 MARC Ethernet Header Pin Assignments (continued)Pin Signal Description74522Board edge Board edge17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 134 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18Table 1-2 MARC Multifunction Header Console Interface Pin AssignmentsPin Signal Description1 CON_RTS_OUT Request To Send18 CON_DTR_OUT Data Terminal Ready
1-5Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 1 Mobile Access Router Card (MARC)MARC Component SystemsAUX ConnectionsThe AUX port is a serial asynchronous port that works at speeds of 1.2 Kbps, 2.4 Kbps, 4.8 Kbps, 9.6 Kbps, 19.2 Kbps, 38.4 Kbps, 57.6 Kbps, and 115.2 Kbps. The console port and AUX port can be accessed simultaneously. For example, you can connect a terminal to the console interface and an external modem or a GPS modem to the AUX port.The AUX port supports the following:•Asynchronous serial DTE •Baud rates range from 1,200 to 115,000 •5 to 8 data bits•1, 1.5, or 2 stop bits•Odd, even, or no parity•Flow control by using RTS, CTS, DTR, and CDC signals 2 CON_TXD_OUT Transmit Data19 GND Ground3 GND Ground20 CON_RXD_IN Receive Data4 CON_DSR_IN Data Set Ready21 CON_CTS_IN Clear To SendTable 1-2 MARC Multifunction Header Console Interface Pin Assignments (continued)Pin Signal DescriptionTable 1-3 MARC Multifunction Header AUX Pin AssignmentsPin Signal Description5 AUX_RTS_OUT Request To Send22 AUX_DTR_OUT Data Terminal Ready6 AUX_TXD_OUT Transmit Data23 GND Ground7 AUX_DSR_IN Data Set Ready24 AUX_RXD_IN Receive Data8 AUX_CD_IN Carrier Detect25 AUX_CTS_IN Clear To Send
1-6Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 1 Mobile Access Router Card (MARC)MARC Component SystemsLED ConnectionsTable 1-4 shows the MARC LEDs supported through the multifunction header that indicate system and LAN status. Power Connections (AUX)A +5V power supply is provided for device connected to AUX port. A GPS modem is used as an example in this section. Typically the +5V power supply current to GPS modems should be limited to less than 200 mA. Table 1-5 shows the pin assignments for power.MARC Power RequirementsThe MARC uses +3.3 V, +5 V, and +12 V power sources. Internal on-board DC-to-DC conversion circuitry generates 1.8 V/1.5 amps from the +3.3V power source.Table 1-4 MARC LEDs Multifunction Header Pin AssignmentsPin Signal Description Function Indicates10 LED_PWR Power–up status LED - (1) Indicates the router operating status. The LED blinks during IOS bootup and is continuously on after the router completes its self-test and begins operating. If the ROMMON self–tests fail, this LED will be off.27 +3.3V LED power supply LED + (1)11 LED_LAN_ACT LAN activity status LED - (2) Blinks when a packet is either transmitted or received on 10/100 Fast Ethernet port.28 +3.3V LED power supply LED + (2)12 LED_LAN_LINK LAN link indicator LED - (3) Indicates the status of the 10/100 Fast Ethernet port. The LED is on while the Ethernet link is up and connected to another device.29 +3.3V LED power supply LED + (3)Table 1-5 MARC Multifunction Header Pin Assignments for PowerPin Signal Description Function9 GND Ground GND26 +5V +5V DC Power Supply PowerTable 1-6 MARC VoltagesVoltage Current Power+5.0 V 0.3 amps 1.5 W+12.0 V 0.1 amps 1.2 W+3.3 V 2.0 amps 6.6 W
CHAPTER 2-1Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-042Fast Ethernet Switch Mobile Interface Card (FESMIC)The Fast Ethernet Switch Mobile Interface Card (FESMIC) is a mobile interface card (MIC) in a standard PC/104-Plus form factor. FESMICs are components of the Cisco 3200 Series Mobile Access Router. The 4-port FESMIC provides 4 sets of switched 10/100 Fast Ethernet signals. The 2-port FESMIC provides 2 sets of switched 10/100 Fast Ethernet signals. The key features of the FESMIC include the following:•Auto-sensing switched 10/100 Fast Ethernet interfaces.•Auto-MDIX (medium-dependent interface crossover). Auto-MDIX automatically detects and corrects crossed Ethernet cabling.•Support for 802.1D standard bridging, 802.1Q trunking, and 802.1P class of service (CoS).•Layer 3 routing support between VLANs.Additional cards and components provide power and link interfaces to the FESMIC. The exact configuration of your router will vary, depending on how it was configured by your vendor.Note This section provides basic information about the FESMIC hardware for the purpose of performing simple troubleshooting, such as reconnecting a loose cable. To solve more difficult problems, please contact your vendor.The FESMIC draws power from the PCI and the ISA connectors. Table 2-1 shows the estimated power consumption. Note that these are theoretical maximum wattages.Table 2-1 FESMIC Estimated Power ConsumptionVoltage Current Draw Power Source+5.0 V 0.2 amps 1.0 W ISA and PCI connectors+3.3 V 2.3 amps 7.7 W PCI connectors
2-2Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC)Auto-Negotiation and Auto-MDI/MDIXAuto-Negotiation and Auto-MDI/MDIXAll of the 10/100 Fast Ethernet interfaces support Ethernet auto-negotiation for the line transmission speed. Both sides of the connection are automatically set to either 10BASE-TX or 100BASE-TX. Auto-negotiation is widely used on most Ethernet interfaces, and it is the default mode. When a 10/100 Fast Ethernet interface is enabled, one end of the link must perform media dependent interface (MDI) crossover (MDIX), so that the transmitter on one end of the data link is connected to the receiver on the other end of the data link (a crossover cable is typically used). The Auto-MDIX feature eliminates the need for crossover cabling by performing an internal crossover when a straight cable is detected during the auto-negotiation phase.If auto-negotiation is disabled, Auto-MDI/MDIX cannot work because there is no signal transmission at initialization to sample the cabling with. Therefore, as in all systems not supporting the HP Auto-MDIX feature, cabling must be correct for the devices being connected. The Auto-MDIX feature is disabled if you explicitly set the line speed rather than leaving the default mode of auto-negotiation. Although it is possible to disable HP Auto-MDIX with auto-negotiation enabled, the current software does not implement an explicit CLI command to allow you to disable Auto-MDIX during auto-negotiation.Auto-negotiation EnableTo enable auto-negotiation, do the following:Router#(config) FastEthernet m/n Router#(config-if) speed auto where m is the slot and n is the port number.Auto-negotiation DisableTo disable auto-negotiation and auto-MDIX by forcing the line speed through a manual setting, do the following:Router#(config) FastEthernet m/n Router#(config-if) speed 10orRouter#(config) FastEthernet m/n Router#(config-if) speed 100MAC Address AllocationThe 4-port FESMIC stores 4 unique MAC addresses for the 10/100 Ethernet interfaces. The 2-port FESMIC stores 2 unique MAC addresses for the 10/100 Ethernet interfaces. In addition, 33 unique MAC addresses are burned into the Mobile Access Router Card (MARC) to support the FESMIC per-VLAN spanning tree (PVST) and inter-VLAN routing features.To provide support for up to 32 VLANs, and the 32 Spanning Tree Protocol (STP) sessions that might be running, 32 unique MAC addresses required for the bridge packet data unit (BPDU) IDs. In addition, one MAC address is needed by the FESMIC for VLAN routing., bringing the total of number of MAC addresses on the wired router to 34. The MAC addresses are burned in the MARC, instead of the FESMIC to support future development.
2-3Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC)FESMIC Component SystemsFESMIC Component SystemsThe ISA buses and PCI buses on the Cisco 3200 Series Mobile Access Router cards provide power to the components on the cards. Both buses comply with the PC/104-Plus standard. The ISA bus allows PC/104-Plus ISA signals to pass through the card bus, but the Cisco cards do not use any of the signals. The PCI bus signals allow the Cisco cards to communicate. Non-Cisco cards cannot communicate with the Cisco 3200 Series Mobile Access Router cards over the PCI bus. Caution If you add non-Cisco cards that generates signals on the PCI bus, the router might shut down. Please do not add non-Cisco cards that generate signals on the PCI bus.Figure 2-1 shows the 2-port FESMIC header and bus locations.Figure 2-1 2-port FESMIC Header and Bus LocationsFigure 2-2 shows the 4-port FESMIC header and bus locations.Figure 2-2 4-port FESMIC Header and Bus Locations1PCI bus 220-pin LED header3ISA bus 4Rotary switch5FE0 10/100 Fast Ethernet header 6FE1 10/100 Fast Ethernet header952281 32465815981 3246 785
2-4Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC)FESMIC Component SystemsNote The PC/104-Plus standard requires that the PCI bus and the ISA bus utilize keying features in the standard stacking headers to guarantee proper module installation. On the PCI bus, pin D30 is removed and the D30 opening is plugged. On the ISA bus, pin C19 and pin B10 are removed, and the C19 and B10 openings are plugged. Signals for the FESMICCisco 3200 Series router cards do not support any ISA bus signals. The PCI bus connector supports communication between Cisco 3200 Series Mobile Access Router cards. Note Non-Cisco MIC cards cannot use PCI signals. The use of PCI signals by non-Cisco cards causes unpredictable results. You cannot add third-party devices that might attempt to communicate with the router through the ISA or PCI bus. The signals are delivered through 10-pin headers, one set of 10/100 Fast Ethernet signals per header. LED signals and 5 V of power are provided through the 20-pin LED header. 10/100 Fast Ethernet Signals on the FESMICThere are 4 fixed 10/100 Fast Ethernet signals on the FESMIC. A Cisco router identifies a 10/100 Fast Ethernet interface address by its slot number and port number, in the form of slot/port. The slot/port addresses of the 10/100 Fast Ethernet interfaces on the FESMIC depend on the position of the rotary switch. For example, if the rotary switch on the 4-port FESMIC is in position 0, the ports are identified as 1/0, 1/1, 1/2, and 1/3. If the rotary switch on the 2-port FESMIC is in position 0, the ports are identified as 1/0 and 1/1.The 10/100 Fast Ethernet port signals are in compliance with IEEE 802.3. They are provided through the Ethernet headers, which support the following:•Auto-negotiation for 10/100BASE-TX connection•Full-duplex and half-duplex modes •Low-power sleep mode•10BASE-T and 100BASE-TX using a single Ethernet connection•Robust baseline wander correction performance •Standard carrier signal multiple access collision detect (CSMA/CD) or full-duplex operation •Integrated LED drivers1PCI bus 220-pin LED header3ISA bus 4Rotary switch5-8 E0–E3 10/100 Fast Ethernet headers
2-5Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC)FESMIC Component SystemsThe FastEthernet ports on the 4-port FESMIC and the 2-port FESMIC are 10/100 Fast Ethernet switch ports. The switch ports support all layer 2 features. The FastEthernet 0/0 port on the MARC is a 10/100 Fast Ethernet router port. The routing features supported on the MARC cannot be configured on the FESMIC ports.Figure 2-3 shows the 10-pin 10/100 Fast Ethernet header pin locations. Figure 2-3 FESMIC Ethernet Header Pin LocationsTable 2-2 describes the pin assignments shown in Figure 2-3.FESMIC LED SignalsFigure 2-4 shows the 20-pin LED header that provides connections for the LEDs. Figure 2-4 FESMIC LED Header Pin LocationsTable 2-3 lists the pin assignments on the FESMIC 20-pin LED header.7452116273849510Board edge Board edgeTable 2-2 FESMIC Ethernet Header Pin AssignmentsPin Signal Description1 RX+ Receive positive6 RX- Receive negative2 TX+ Transmit positive7 Unused Terminated3 Unused Terminated8 TX- Transmit negative4 Unused Terminated9 Unused Terminated5 Reserved Do not use10 Reserved Do not use81599Board edge Board edge10 9 8 7 6 5 4 3 2 120 19 18 17 16 15 14 13 12 11
2-6Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC)FESMIC Component SystemsTable 2-3 FESMIC LED Header Pin AssignmentsPin Signal Description1 Port0 LINK+ Link Positive LED terminal Port 0 (power supply)The LED is on while the 10/100 Fast Ethernet link is up and connected to another device.11 Port0 LINK- Link Negative LED terminal Port 0 2 Port0 ACT+ Active Positive LED terminal Port 0 (power supply)Blinks when a packet is either transmitted or received.12 Port0 ACT- Active Negative LED terminal Port 0 3 Port1 LINK+ Link Positive LED terminal Port 1 (power supply)The LED is on while the 10/100 Fast Ethernet link is up and connected to another device.13 Port1 LINK- Link Negative LED terminal Port 1 4 Port1 ACT+ Active Positive LED terminal Port 1 (power supply)Blinks when a packet is either transmitted or received.14 Port1 ACT- Active Negative LED terminal Port 1 5 Port2 LINK+ Link Positive LED terminal Port 2 (power supply)The LED is on while the 10/100 Fast Ethernet link is up and connected to another device (4-port FESMIC only).15 Port2 LINK- Link Negative LED terminal Port 26 Port2 ACT+ Active Positive LED terminal Port 2 (power supply)Blinks when a packet is either transmitted or received (4-port FESMIC only).16 Port2 ACT- Active Negative LED terminal Port 27 Port3 LINK+ Link Positive LED terminal Port 3 (power supply)The LED is on while the 10/100 Fast Ethernet link is up and connected to another device (4-port FESMIC only).17 Port3 LINK- Link Negative LED terminal Port 38 Port3 ACT+ Active Positive LED terminal Port 3 (power supply)Blinks when a packet is either transmitted or received (4-port FESMIC only).18 Port3 ACT- Active Negative LED terminal Port 39 Open Do not use19 Open Do not use10 Open Do not use20 Open Do not use
2-7Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC)FESMIC Component SystemsFESMIC Rotary Switch PositionsThe rotary switch position determines the IOS port number for the MIC. Table 2-4 shows the mapping of the switch positions to the IOS slot numbers.Caution The rotary switch positions must be unique and should not be assigned to more than one MIC. If a MIC rotary switch is set to 3 or higher, the message is:“MIC-3-SLOTNOTSUPPORTED: The MIC cannot operate when the rotary switch is in position 3. Change the switch position to one of the supported, unused positions 0-2.”If two or more MICs have the rotary switches set to the same position, or if one or more MICs are in rotary switch position 4 through 7, the router might crash after displaying the following error message:“Non-recoverable error occurred. Please check the rotary switch positions on the MIC cards for the possible misconfiguration of the switch position.”Table 2-5 shows the FESMIC 10/100 Fast Ethernet signal assignments. The position of the rotary switch determines the port assignments. Although the rotary switch has eight positions, only one of three positions can be selected. The rotary switch position should be unique for each MIC.Table 2-4 FESMIC Rotary Switch PositionsSwitch Position IOS Slot Number0112233–7 Not supportedTable 2-5 FESMIC Rotary Switch Positions and Signal AssignmentsRotary Switch Position MIC Slot Fast Ethernet Signal Assignments0 1 FE 1/0 FE 1/1 FE 1/211. 4-port FESMIC onlyFE 1/311 2 FE 2/0 FE 2/1 FE 2/21FE 2/312 3 FE 3/0 FE 3/1 FE 3/21FE 3/31
2-8Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 2 Fast Ethernet Switch Mobile Interface Card (FESMIC)FESMIC Component Systems
CHAPTER 3-1Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-043Serial Mobile Interface Card (SMIC)The Serial Mobile Interface Card (SMIC) is one component of the Cisco 3200 Series Mobile Access Router. It provides the router up to 4 high–speed sets of serial signals in both data terminal equipment (DTE) and data circuit equipment (DCE) modes. Additional components provide power and link interfaces to the SMIC. For example, the Mobile Access Router Card (MARC) provides the host processor, memory, and headers for the 10/100 Fast Ethernet, console, and auxiliary signals for the router. The exact configuration of your router will vary, depending on how it was configured by your vendor.Note This section provides basic information about the SMIC hardware for the purpose of performing simple troubleshooting, such as reconnecting a loose cable. To solve more difficult problems, please contact your vendor.Each SMIC provides the following:•Support for 2 to 4 sets of serial signals with protocol support for HDLC, asynchronous, synchronous and octet-oriented PPP modes. The signals can be configured to any serial standard (EIA/TIA-232, EIA/TIA-449, EIA/TIA-530, EIA/TIA-530A, EIA/TIA-X.21, or CCITT V.35).•DCE and DTE mode support on each set of serial signals.•Speeds of 2 Mbps for synchronous data transfer and 115 Kbps for asynchronous data transfer on each serial interface. All serial standards reach 2 Mbps (for synchronous) except for the EIA/TIA-232 standard which supports up to 192K.Note The PCI bus and ISA bus utilize keying features in the standard stacking headers to guarantee proper module installation. On the PCI bus, pin D30 is removed and the D30 opening plugged. On the ISA Bus, pin C19 and pin B10 are removed, and the pin C19 and pin B10 openings are plugged. The SMIC draws power from the PCI and the ISA connectors. Table 3-1 shows the estimated power consumption. Note that these are theoretical maximum wattages.Table 3-1 SMIC Estimated Power ConsumptionVoltage Current Draw Power Source+5.0 V 1.0 amps 5.0 W ISA and PCI connectors+3.3 V 0.5 amps 1.7 W PCI connectors
3-2Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 3 Serial Mobile Interface Card (SMIC)SMIC Component SystemsSMIC Component SystemsFigure 3-1 shows the 2-port SMIC header and bus locations.Figure 3-1 2-port SMIC Header and Bus LocationsFigure 3-2 shows the 4-port SMIC header and bus locations.Caution If you add non-Cisco cards that generates signals on the PCI bus, the router might shut down. Please do not add non-Cisco cards that generate signals on the PCI bus.Figure 3-2 4-port SMIC Header and Bus Locations1PCI bus 260-pin multifunction header for Serial 0 and Serial 1 signals3ISA bus 4Rotary switch952271 3241PCI bus 260-pin multifunction header for Serial 2 and Serial 3 signals3ISA bus 4Rotary switch560-pin multifunction header for Serial 0 and Serial 1 signals745191 3254
3-3Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 3 Serial Mobile Interface Card (SMIC)SMIC Component SystemsSignals for the SMICThe Cisco SSB Serial standard supports the following:•EIA/TIA-232, EIA/TIA-449, EIA-530, EIA-530A, X.21, and V.35 standards in both DTE or DCE modes.•Signals (SSB and LED) are provided through the 60-pin multifunction header(s).The position of the rotary switch determines the port assignments. Although the rotary switch has eight positions, only position 0, 1, and 2 are supported on the 4-port SMIC and only position 0 and 1 are supported on the 2-port SMIC.Table 3-2 provides 4-port SMIC port assignments.Table 3-3 provides the 2-port SMIC port assignments.Serial Cable LengthMaximum Cable length depends on a number of factors, including how well the sender and receiver are implemented regarding rise times, and cable capacitance, inductance and screening. These are all difficult to quantify, but the primary factor is the data rate. Typically, doubling the data rate halves the recommended maximum cable length. The RS-232 specification limits cable length to 15.25 metres (50 feet) at a maximum data rate of 20,000 bps. The Cisco 3200 Series router RS-232 serial interfaces data rate is 115,200 bps and are limited to a maximum cable length of 2.8 meters (8 feet).Table 3-2 4-port SMIC Rotary Switch Settings and Port AssignmentsPosition MIC Slot Port Assignments0 1 Serial 1/0 Serial 1/1 Serial 1/2 Serial 1/31 2 Serial 2/0 Serial 2/1 Serial 2/2 Serial 2/32 3 Serial 3/0 Serial 3/1 Serial 3/2 Serial 3/3Table 3-3 2-port SMIC Rotary Switch Settings and Port AssignmentsPosition MIC Slot Port Assignments0 1 Serial 1/0 Serial 1/11 2 Serial 2/0 Serial 2/1
3-4Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 3 Serial Mobile Interface Card (SMIC)SMIC Component SystemsSMIC LED SignalsTable 3-4 shows the LED signals that are supported on the SMIC, along with the corresponding functions. Serial 2 and Serial 3 apply to the 4-port SMIC only.4-Port SMIC Rotary Switch PositionsTable 3-5 shows the 4-port SMIC serial signal assignments. The position of the rotary switch determines the port assignments. Although the rotary switch has 8 positions, only 1 of 3 positions can be selected. The rotary switch position should be unique for each mobile interface card (MIC) card.Table 3-4 SMIC LED FunctionsLED FunctionSERIAL0 ACTIVITY Blinks once when a packet is either transmitted or received on Serial 0, and originates from Header 5. SERIAL0 LINK Indicates the status of Serial 0 and originates from Header 5. The LED is on when a serial port is in DTE mode, and when the data set ready (DSR), data carrier detect (DCD), and clear to send (CTS) signals are detected. The LED is on when a serial port is in DCE mode, and when the data terminal ready (DTR) and request to send (RTS) signals have been detected.SERIAL1 ACTIVITY Blinks once when a packet is either transmitted or received on Serial 1. Originates from Header 5. SERIAL1 LINK Indicates the status of Serial 1, and originates from Header 5. The LED is on when the serial port is in DTE mode, and when the data set ready (DSR), data carrier detect (DCD), and clear to send (CTS) signals are detected. The LED is on when the serial port is in DCE mode, and when the data terminal ready (DTR) and request to send (RTS) signals have been detected.SERIAL2 ACTIVITY Blinks once when a packet is either transmitted or received on Serial 2. Originates from Header 2. SERIAL2 LINK Indicates the status of Serial 2, and originates from Header 2. The LED is on when the serial port is in DTE mode, and when the data set ready (DSR), data carrier detect (DCD), and clear to send (CTS) signals are detected. The LED is on when the serial port is in DCE mode, and when the data terminal ready (DTR) and request to send (RTS) signals have been detected.SERIAL3 ACTIVITY Blinks once when a packet is either transmitted or received on Serial 3. Originates from Header 2. SERIAL3 LINK Indicates the status of Serial 3, and originates from Header 2. The LED is on when the serial port is in DTE mode, and when the data set ready (DSR), data carrier detect (DCD), and clear to send (CTS) signals are detected. The LED is on when the serial port is in DCE mode, and when the data terminal ready (DTR) and request to send (RTS) signals have been detected.Table 3-5 4-port SMIC Rotary Switch Positions and Serial Set Signal AssignmentsRotary Switch Position MIC Slot Signal Assignments0 1 Serial 1/0 Serial 1/1 Serial 1/2 Serial 1/31 2 Serial 2/0 Serial 2/1 Serial 2/2 Serial 2/3
3-5Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 3 Serial Mobile Interface Card (SMIC)SMIC Component Systems2 3 Serial 3/0 Serial 3/1 Serial 3/2 Serial 3/33 4 Serial 4/0 Serial 4/1 Serial 4/2 Serial 4/3Table 3-5 4-port SMIC Rotary Switch Positions and Serial Set Signal AssignmentsRotary Switch Position MIC Slot Signal Assignments
3-6Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 3 Serial Mobile Interface Card (SMIC)SMIC Component Systems
CHAPTER 4-1Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-044Wireless Mobile Interface Card (WMIC)The Wireless Mobile Interface Card (WMIC) is a mobile interface card (MIC) in a standard PC/104-Plus form factor. It is one component of the Cisco 3200 Series Mobile Access Routers and provides a 2.4-GHz (802.11b/g) or 4.9-GHz (US Only, Public Safety) wireless interface. The WMIC can be configured as a:•Wireless Access Point•Wireless Root Bridge•Wireless Non-root Bridge•Wireless Work Group Bridge.The WMIC communicates with the router through its 10/100 Fast Ethernet interface. Note This chapter provides basic information about the WMIC hardware for the purpose of performing simple troubleshooting, such as reconnecting a loose cable. To solve more difficult problems, please contact your vendor.Caution The 4.9-GHz (US Only, Public Safety) radio requires an operators license and can only be operated by US Public Safety operators who meet the requirements specified under FCC Part 90.20.WMIC Component SystemsThe ISA buses and PCI buses on the Cisco 3200 Series Mobile Access Router cards provide power to the components on the cards. The WMIC does not receive or transmit communications signals on the buses, but it will pass signals through to a card above or below the WMIC. Both buses comply with the PC/104-Plus standard. The PCI bus signals allow the Cisco cards to communicate. Non-Cisco cards cannot communicate with the Cisco 3200 Series Mobile Access Router cards over the PCI bus. Caution If you add non-Cisco cards that generates signals on the PCI bus, the router might shut down. Please do not add non-Cisco cards that generate signals on the PCI bus.
4-2Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)WMIC Component SystemsFigure 4-1 shows the WMIC header and bus locations.Figure 4-1 WMIC Header and Bus LocationsNote The PC/104-Plus standard requires that the PCI bus and the ISA bus utilize keying features in the standard stacking headers to guarantee proper module installation. On the PCI bus, pin D30 is removed and the D30 opening is plugged. On the ISA bus, pin C19 and pin B10 are removed, and the C19 and B10 openings are plugged. Signals for the WMICCisco 3200 Series router cards do not support any ISA bus signals. The PCI bus connector supports communication between Cisco 3200 Series Mobile Access Router cards. Note Non-Cisco MIC cards cannot use PCI signals. The use of PCI signals by non-Cisco cards causes unpredictable results. You cannot add third-party devices that might attempt to communicate with the router through the ISA or PCI bus. The 10/100 Fast Ethernet signals are delivered through a 10-pin header. LED signals and RS-232 console signals are provided through the 24-pin multifunction header. 1PCI bus 2Left antenna connector (J2)3Right antenna connector (J1) 4ISA bus510-pin 10/100 Fast Ethernet header 624-pin multifunction header103981421356
4-3Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)WMIC Component Systems10/100 Fast Ethernet Signals on the WMICThere is one set of fixed 10/100 Fast Ethernet signals on the WMIC. The 10/100 Fast Ethernet port signals are in compliance with IEEE 802.3. They are provided through the Ethernet headers, which support the following:•Auto-negotiation for 10/100BASE-TX connection•Full-duplex and half-duplex modes •Low-power sleep mode•10BASE-T and 100BASE-TX using a single Ethernet connection•Robust baseline wander correction performance •Standard carrier signal multiple access collision detect (CSMA/CD) or full-duplex operation •Integrated LED driversFigure 4-2 shows the 10-pin 10/100 Fast Ethernet header pin locations. Figure 4-2 WMIC Ethernet Header Pin LocationsTable 4-1 describes the pin assignments shown in Figure 4-2.Note If Auto-MDIX is disabled, when connecting to Ethernet switches or repeaters a straight-through cable can be used. When connecting to compatible workstations, servers, and routers, a crossover cable should be used. If Auto-MDIX is enabled, either a straight-through or crossover cable can be used can be used to make the connection, as the router automatically changes the signals on the pins to compensate.7452116273849510Board edge Board edgeTable 4-1 WMIC Ethernet Header Pin AssignmentsPin Signal Description1 TX+ Transmit positive6 TX- Transmit negative2 RX+ Receive positive7 Unused Terminated3 Unused Terminated8 RX- Receive negative4 Unused Terminated9 Unused Terminated5 Reserved Do not use10 Reserved Do not use
4-4Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)WMIC Component SystemsWMIC Multifunction Header SignalsThe multifunction header contains RS-232 console signals and three-color status LED signals. Figure 4-3 shows the 24-pin multifunction header that provides connections for the LEDs. Figure 4-3 WMIC Multifunction Header Pin LocationsTable 4-2 lists the pin assignments on the WMIC 20-pin LED header.103464Board edge Board edge9 8 7 6 5 4 3 2 11020112112222324 19 18 17 16 15 14 13Table 4-2 WMIC Multifunction Header Pin AssignmentsPin Signal1 Negative Ethernet RED LED terminal13 Shared Positive Ethernet LED terminal2 Negative Ethernet GREEN LED terminal14 Negative Radio/RF RED LED terminal3 Shared Positive Radio/RF LED terminal15 Negative Radio/RF GREEN LED terminal4 Negative Wireless Status RED LED terminal16 Shared Positive Wireless Status LED terminal5 Negative Wireless Status GREEN LED terminal17 Negative Installation RED LED terminal6 Shared Positive Installation/Operation LED terminal18 Negative Operation GREEN LED terminal7 Not Used (No Connection)19 Console TX - Transmit Data8 Console RX - Receive Data20 Console GND - Signal Ground9 Reserved21 Reserved10 Reserved22 Reserved11 Reserved23 Reserved12 Reserved24 Reserved
4-5Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)WMIC Component SystemsLED BehaviorDuring normal operations, the indicator signals on the wireless device have the following meanings. •The status indicator signals operational status. Steady green indicates that the wireless device is associated with at least one wireless client. Blinking green indicates that the wireless device is operating normally but is not associated with any wireless devices.•The radio indicator blinks green to indicate radio traffic activity. The light is normally off, but it blinks whenever a packet is received or transmitted over the radio.•The Ethernet indicator signals traffic on the wired LAN. This indicator is normally green when an Ethernet cable is connected, and blinks green when a packet is received or transmitted over the Ethernet infrastructure. The indicator is off when the Ethernet cable is not connected. Table 4-3 shows the details of LED behavior.Table 4-3 Indicator SignalsMessage typeEthernet indicatorStatusindicatorRadioindicatorMeaningBoot loader statusGreen – Green DRAM memory test.– Amber Red Board initialization test.– Blinking greenBlinking greenFlash memory test.Amber Green – Ethernet initialization test.Green Green Green Starting Cisco IOS software.Association status– Green – At least one wireless client device is associated with the unit.– Blinking green– No client devices are associated; check the wireless device SSID and WEP settings.Operating status–GreenBlinking greenTransmitting/receiving radio packets.Green – – Ethernet link is operational.Blinking green– – Transmitting/receiving Ethernet packets.Boot Loader ErrorsRed – Red DRAM memory test failure.– Red Red File system failure.Red Red – Ethernet failure during image recovery.Amber Green Amber Boot environment error.Red Green Red No Cisco IOS image file.Amber Amber Amber Boot failure.Operation Errors–GreenBlinking amberMaximum retries or buffer full occurred on the radio.Blinking amber– – Transmit/receive Ethernet errors. – Blinking amber– General warning.
4-6Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)Key FeaturesAntenna ConnectorOn the radio card, there are two ultra-miniature coaxial connectors (U.FL connector) that are used to connect the coax cables between the WMIC and the external antenna connectors. This low profile connector offers frequency performance up to 6-GHz. Two connectors are used to support antenna diversity. The cable should be as short as possible to minimize the loss in strength of the radio frequency (RF) signal. The cable carries the RF signal from the antenna to the low noise amplifier (LNA) on the receiver and transmits the RF signal from power amplifier (PA) to the antenna that radiates the RF signal.There are many antenna connector families. The Cisco RP-TNC antenna connector can be used to support standard antennas. Key FeaturesThis section lists the key features of the radios.2.4-GHz (802.11b/g) WMIC and the 4.9-GHz (US Only, Public Safety) FeaturesThe key features of the 2.4-GHz (802.11b/g) WMIC and the 4.9-GHz (US Only, Public Safety) WMIC are listed below.Configuration Reset– Amber – Resetting the configuration options to factory defaults.Failures Red Red Red Firmware failure; try disconnecting and reconnecting unit power.Blinking red – – Hardware failure. The wireless device must be replaced.Firmware Upgrade– Red – Loading new firmware image.Table 4-3 Indicator Signals (continued)Message typeEthernet indicatorStatusindicatorRadioindicatorMeaningTable 4-4 WMIC Key FeaturesWireless Medium Direct Sequence Spread Spectrum (DSSS) Orthogonal Frequency Division Multiplexing (OFDM)Media Access Protocol Carrier sense multiple access with collision avoidance (CSMA/CA)SNMP Compliance MIB I and MIB IIEncryption Key Length 128-bitVirtual LAN (VLAN) Support The segmentation of up to 16 user groups is allowed.Quality of Service (QoS) Support Prioritization of traffic for different requirements, such as voice and video.
4-7Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)Key FeaturesNote If no FESMIC is installed, the Cisco 3200 Series routers support a maximum of one WMIC on each router. The routers support a maximum of three WMICs on each router when a FESMIC is installed.MAC Address AllocationThe WMIC stores one unique MAC address for the BVI interface. Security Cisco Wireless Security Suite including:Authentication:•802.1X support including LEAP, PEAP, EAP-TLS, EAP-TTLS, and EAP-SIM to yield mutual authentication and dynamic, per-user, per-session WEP keys •MAC address and by standard 802.11 authentication mechanisms Encryption:•Support for static and dynamic IEEE 802.11 WEP keys of 40 bits and 128 bits •Pre-standard TKIP WEP enhancements: key hashing (per-packet keying), message integrity check (MIC), and broadcast key rotation Status Indicators LEDs provide information concerning association status, operation, error/warning, firmware upgrade, and configuration, network/modem, and radio statusMemory 8MB Flash32 MB DRAMAutomatic Configuration Support BOOTP and DHCPRemote Configuration Support Telnet, HTTP, FTP, TFTP, and SNMPUplink Auto-sensing 10/100BaseT EthernetLocal Configuration Console port Table 4-4 WMIC Key Features
4-8Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)Key FeaturesDifferences Between 2.4-GHz (802.11b/g) and 4.9-GHz (US Only, Public Safety) RadiosTable 4-5 Differences between 2.4-GHz WMIC and 4.9-GHz WMIC2.4-GHz (802.11b/g) 4.9-GHz (US Only, Public Safety) CommentPower Maximum OFDM power level is 15dbm (30mw), but the power level might vary by country.Maximum OFDM power level is 17dbm (50mw).power client Command Supported Not supported. Use the power command.Concatenation Supported. Not supported.Fragmentation Maximum threshold is 4000 bytes. Maximum threshold is 2346 bytes. Fragment counter is in units of fragmented packets.distance Command (to minimize delay propagation)Supported up to 99 kilometers. Supported up to 3 kilometers (1.8 miles).World Mode Supported. Not supported.HTML-Based User Interface Supported Not supportedVLANs 16 unencrypted VLANs, 16 static key VLANs, or 16 dynamic key VLANs, 16 unencrypted VLANs, 1 static key VLAN, or 4 dynamic key VLANs.Wireless encryption/cipher suitesWEP-40, WEP-128, TKIP, CKIP, CMIC and CKIP-CMICWEP-40, WEP-128, TKIP and AES-CCMMax Number of Stations with WEP 255 116Max Number of Stations with TKIP 256 26Max Number of Stations with AES-CCM256 116WDS server Not supported. The 4.9-GHz WMIC can be configured to act as WDS server.WDS client The 2.4-GHz WMIC acting as root device can auto discover and work with a subnet WDS server.The 4.9-GHz WMIC acting as root device can auto discover and work within a subnet WDS server. If IP address of a WDS server is statically configured on a 4.9-GHz WMIC acting as root device, the WMIC can also work with a central WDS server located anywhere on the network.EAP-TLS, EAP-TTLS Supported Not SupportedWDS Server related MIBS N/A Supported
4-9Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)Key Features2.4-GHz (802.11b/g) FeaturesThe key features of the 2.4-GHz (802.11b/g) WMIC are listed below.Data Rates Supported 1, 2, 5.5, 6, 9, 11, 12, 18, 24, 36, 48, and 54 MbpsNetwork Standard IEEE 802.11b and IEEE 802.11gFrequency Band 2.400-GHz to 2.497-GHzModulation BPSK 1Mbps and 6MbpsQPSK 2 Mbps and 12 MbpsCCK 5.5 MbpsBPSK 9.6 MbpsCCK2 11 MbpsQPSK 18 Mbps16 QAM 24 Mbps and 36 Mbps64 QAM 48 Mbps and 54 MbpsOperating Channels North America: 11; ETSI: 13; Japan: 14Receive Sensitivity 1Mbps: -94dBm2Mbps: -91dBm5.5 Mbps: -89 dBm11 Mbps: -85 dBmAvailable Transmit Power Settings 100 mW (20 dBm)50 mW (17 dBm)30 mW (15 dBm)20 mW (13 dBm)5mW (7dBm)1mW (0dBm)Maximum power setting will vary according to individual country regulations.Range (typical @ 1000-mW transmit power setting with 6 dBi diversity dipole antenna) Outdoor:0.5 mile (804 m) @ 45 Mbps1 mile (1609 m) @ 11 Mbps3 miles (4,827 m) @ 1 MbpsCompliance 2.4-GHz (802.11b/g) operates license free under FCC Part 15 and complies as a Class B device; complies with DOC regulations; complies with ETS 300.328, FTZ 2100, and MPT 1349 standards; rugged version complies with UL 2043
4-10Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)Key Features4.9-GHz (US Only, Public Safety) FeaturesThe key features of the 4.9-GHz (US Only, Public Safety) WMIC are listed below.4.9 -GHz ChannelsTable 4-6 shows the channel options for the 4.94-GHz to 4.99-GHz band for the United States regulatory domain.Data Rates Supported 5-MHz channelization: 1.5, 2.25, 3, 4.5, 6, 9, 12, and 13.5 Mbps10-MHz channelization: 3, 4.5, 6, 9, 12, 18, 24, and 27 Mbps20-MHz channelization: 6, 9, 12, 18, 24, 36, 48, and 54 MbpsNetwork Standard Currently there is no IEEE 4.9-GHz (US Only, Public Safety) standard; however, it is similar to the IEEE 802.11a standard.Frequency Band 4.940-GHz to 4.990-GHzOperating Channels North America: 11Available Transmit Power Settings 40 mW (16 dBm)30 mW (15 dBm)20 mW (13 dBm)10 mW (10 dBm)5mW (7dBm)Compliance 4.9-GHz (US Only, Public Safety): •Operation restricted to operators meeting requirements of CFR47 Part 90.20 of the technical rules for qualification as a Public Safety operator.•Requires a FCC license to operate under this part of the Part 90 RegulationTable 4-6 FCC 4.9 Operational Channels as per TIA TR-8 specificationOperating Channel NumbersChannel Center 5-MHz Channel SpacingChannel Center 10-MHz Channel SpacingChannel Center 20-MHz Channel Spacing135 4942.57910 4945.015 4947.520 4950.0 4950.025 4952.5
4-11Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)Key FeaturesNote Channel Center Frequencies (MHz) 1-MHz Channel Spacing is documented in the TIA TR-8 specification, but it is not supported by the 4.9-GHz (US Only, Public Safety) WMIC.ThroughputThe throughput is a minimum of:•4 Mbps half-duplex at one mile line-of-sight for a 5-MHz-wide channel•8 Mbps half-duplex at one mile line-of-sight range for a 10-MHz-wide channel. •16 Mbps half-duplex at one mile line-of-sight range for a 20-MHz-wide channel. 30 4955.0 4955.035 4957.540 4960.0 4960.045 4962.550 4965.0 4965.055 4967.560 4970.0 4970.065 4972.570 4975.0 4975.075 4977.580 4980.0 4980.085 4982.590 4985.0919395 4987.59799Table 4-6 FCC 4.9 Operational Channels as per TIA TR-8 specification (continued)Operating Channel NumbersChannel Center 5-MHz Channel SpacingChannel Center 10-MHz Channel SpacingChannel Center 20-MHz Channel Spacing
4-12Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)Power RequirementsModulationTable 4-7 shows the modulation.Receive SensitivityTable 4-8 shows the receive sensitivity.Power RequirementsAdditional cards and components provide power and link interfaces to the WMIC. The exact configuration of your router will vary, depending on how it was configured by the vendor.The WMIC draws power from the PCI and the ISA connectors. Table 4-9 shows the estimated power consumption. Note that these are theoretical maximum wattages.Table 4-7 ModulationModulation 5 Mbps 10 Mbps 20 MbpsBPSK 1.5 Mbps and 2.25 Mbps 3 Mbps and 4.5 Mbps 6 Mbps and 9 MbpsQPSK 3 Mbps and 4.5 Mbps 6 Mbps and 9 Mbps 12 Mbps and 18 Mbps16 QAM 6 Mbps and 9 Mbps 12 Mbps and 18 Mbps 24 Mbps and 27 Mbps64 QAM 12 Mbps and 13.5 Mbps 24 Mbps and 27 Mbps 48 Mbps and 54 MbpsTable 4-8 Receive Sensitivity5-MHz 10-MHz 20-MHz1.5 Mbps -89 dBm 3 Mbps -87 dBm 6 Mbps -85 dBm2.25 Mbps -89 dBm 4.5 Mbps -87 dBm 9 Mbps -85 dBm3Mbps -89 dBm 6 Mbps -87 dBm 12 Mbps -85 dBm4.5 Mbps -85 dBm 9 Mbps -87 dBm 18 Mbps -82 dBm6 Mbps -82 dBm 12 Mbps -85 dBm 24 Mbps -79 dBm9 Mbps -79 dBm 18 Mbps -79 dBm 36 Mbps -76 dBm12 Mbps -74 dBm 24 Mbps -74 dBm 48 Mbps -71 dBm13.5 Mbps -72 dBm 27 Mbps -72 dBm 54 Mbps -69 dBmTable 4-9 WMIC Power RequirementVoltage Current Draw Power Source+5.0 V 0.4 amps 2.0 W ISA and PCI connectors+3.3 V 1.7 amps 5.6 W PCI connectors
4-13Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)Related DocumentationRelated DocumentationThese documents provide detailed information regarding the configuration of the wireless card:•Cisco IOS Switching Services Configuration Guide. Click this link to browse to this document:http://www.cisco.com/univercd/cc/td/doc/product/software/ios122/122cgcr/fswtch_c/index.htm•Cisco Internetwork Design Guide. Click this link to browse to this document:http://www.cisco.com/univercd/cc/td/doc/cisintwk/idg4/index.htm•Cisco Internetworking Technology Handbook. Click this link to browse to this document:http://www.cisco.com/univercd/cc/td/doc/cisintwk/ito_doc/index.htm•Cisco Internetworking Troubleshooting Guide. Click this link to browse to this document:http://www.cisco.com/univercd/cc/td/doc/cisintwk/itg_v1/index.htm
4-14Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Chapter 4 Wireless Mobile Interface Card (WMIC)Related Documentation
IN-1Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04INDEXNumerics10/100 Fast Ethernetauto-negotiation 2-2signals 1-1, 2-1, 4-12.4-GHz (802.11b/g) WMIC 4-13rd-party devices 1-24.9-MHz (public safety) WMIC 4-1802.1D 2-1802.1P 2-1802.1Q 2-1AasynchronousAUX 1-1, 1-5baud rates 1-4data transfer 3-1DTE 1-5GPS 1-1audience iiAuto-MDIX 2-1, 2-2, 4-3auto negotiation 1-1auto-negotiation 2-2AUX interfacesignals 1-4specifications 1-5Bbaud rate, serial 1-4bridge packet data unit (BPDU) 2-2bridging 2-1broadcast key rotation 4-9bus communication 1-2, 2-3, 3-1, 4-1bus keying feature 1-2, 2-4, 3-1, 4-2CcardsCisco FESMIC 2-1Cisco MARC 1-1Cisco SMIC 3-1Cisco WMIC 4-1CCITT V.35 3-1Cisco FESMIC 2-1Cisco MARC 1-4Cisco SMIC 3-1Cisco WMIC 4-4, 4-6, 4-7, 4-9class of service (CoS) 2-1console portMARC signals 1-4WMIC signals 4-4console port interfaceCisco MARC 1-4Cisco WMIC 4-4crossover cable 2-2DDCE mode 3-1disabling auto-negotiation 2-2DRAM 1-1DTEasynchronous 1-5mode 3-1
IndexIN-2Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04EEIA/TIA-232 3-1EIA/TIA-449 3-1EIA/TIA-530 3-1EIA/TIA-530A 3-1EIA/TIA-X.21 3-1enabling auto-negotiation 2-2Ethernetheader 1-3indicator 4-5FFast Ethernetheader pin locationsCisco FESMIC 2-5Cisco MARC 1-3Cisco WMIC 4-3interfaceCisco FESMIC 2-4Cisco MARC 1-3Cisco WMIC 4-3router port 1-4signalsCisco FESMIC 2-1Cisco MARC 1-1Cisco WMIC 4-1switch port 1-4, 2-5Flash memory 1-1flow control 1-5GGPSmodem 1-5power 1-6HHDLC 3-1header keying 1-2, 2-4, 3-1, 4-2header locationsCisco FESMIC 2-3Cisco MARC 1-2Cisco SMIC 3-2Cisco WMIC 4-2Iindustry-standard architecture (ISA) 1-2interface identificationFast EthernetCisco FESMIC 2-4Cisco MARC 1-3Cisco WMIC 4-3serialCisco MARC 1-4Cisco SMIC 3-4interfacesAUX 1-5Cisco FESMIC 2-4Cisco MARC 1-3Cisco SMIC 3-1Cisco WMIC 4-2, 4-3console port 1-4, 4-4Fast EthernetCisco FESMIC 2-4Cisco MARC 1-3Cisco WMIC 4-2, 4-3serialCisco MARC 1-1Cisco SMIC 3-4inter-VLAN routing 2-2ISA bussignals 1-2, 2-3, 4-1
IndexIN-3Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Kkey hashing 4-9keying feature 1-2, 2-4, 3-1, 4-2LLEAP 4-9LEDCisco FESMIC 2-4Cisco MARC 1-3Cisco SMIC 3-4Cisco WMIC 4-2LED indicatorsEthernet 4-5radio traffic 4-5status 4-5MMAC address 2-2, 4-10MDIX 2-2media dependent interface (MDI) 2-2medium-dependent interface crossover 2-1memoryFlash 1-1PC system requirements viimessage integrity check 4-9Mobile Access Router Card 1-1modemAUX connection 1-5control signals 1-4DTR, DSR, RTS, and CTS signals 1-4GPS modem 1-5multifunction header 1-3, 1-4Nnon-Cisco cardsbus communication 1-2, 2-3, 3-1, 4-1PPC-104-Plus 1-2PCI bus 1-2, 2-3, 4-1PCI bus version 1-1PEAP 4-9per-VLAN spanning tree (PVST) 2-2portsAUX signals 1-4console signals 1-4, 4-4Fast Ethernet interface signals 1-1, 2-1, 4-1serial interface signals 1-1power consumptionCisco FESMIC 2-1Cisco MARC 1-6Cisco SMIC 3-1Cisco WMIC 4-10PPP modes 3-1processor 1-1QQoS 4-9Rradioindicator 4-5range 4-7rotary switch 3-3Cisco FESMIC 2-7Cisco SMIC 3-4router cards
IndexIN-4Cisco 3200 Series Mobile Access Router Hardware GuideOL-5816-04Cisco FESMIC 2-1Cisco MARC 1-1Cisco SMIC 3-1Cisco WMIC 4-1RS232 transceiver 1-4Sserialasynchronous port 1-5baud rates 1-4signals 1-1, 3-1serial interfaceCisco MARC 1-1Cisco SMIC 3-4signalsCisco FESMIC 2-4Cisco MARC 1-3Cisco SMIC 3-3Cisco WMIC 4-2Fast Ethernet 1-3, 2-1, 4-1ISA bus 1-2, 2-3, 4-1PCI bus 1-2, 2-3, 4-1serial 1-3, 3-3Spanning Tree Protocol (STP) 2-2status indicators 4-5switch, rotary 2-7synchronous 3-1system requirements viiTthird-party devices 2-4, 4-2TKIP 4-9trunking 2-1VVLAN routing 2-2WWEP 4-9WMICs 4-1Zzeroization 1-1

Navigation menu