Clarinox Technologies 1531 Koala Connect User Manual Module

Clarinox Technologies Pty Ltd Koala Connect Module

Contents

User Manual Module

Clarinox Technologies Pty. Ltd. ABN 89 062 954 170 28 / 296 Bay Rd Cheltenham VIC 3192 Tel (613) 9095 8088 www.clarinox.com KM-153103 koala® connect (aka Joey®) DATASHEET The information contained herein shall not be disclosed to unauthorized persons. This document remains the property of Clarinox Technologies Pty Ltd. It contains proprietary and confidential information and is considered to be a trade secret by Clarinox Technologies Pty Ltd. No information contained herein is to be shared, copied, disclosed, or otherwise compromised in any way without the written consent of Clarinox Technologies Pty Ltd. The contents of this document are subject to change without notice. Clarinox Technologies Pty Ltd reserves the right to make changes in this document as progress in planning, development, engineering or manufacturing warrants. All Rights Reserved, Copyright Clarinox Technologies Pty Ltd © 2018
KM-153103 Datasheet Page 1 Revision History Revision Date Designed by Approved by Description 1.0 08 May 2018 ND GT Initial draft 1.1 15 June 2018 ND GT FCC Certification warning details added
KM-153103 Datasheet Page 2 Table of Contents Highlights ................................................................................................................................ 4 Product Description ................................................................................................................ 4 Module Certification Details ........................................................................................... 5 1.2.1.1 Federal Communications Commission (FCC) Statement ............................................ 5 1.2.1.2 End Product Labelling ................................................................................................. 5 Important Notice to OEM Integrators ............................................................................ 5 Antenna Installation ........................................................................................................ 6 Manual Information to the End User .............................................................................. 6 Federal Communication Commission Interference Statement ...................................... 6 Radiation Exposure Statement ....................................................................................... 7 Product Selector ...................................................................................................................... 8 Module Pinouts ....................................................................................................................... 8 Hardware Interfaces ............................................................................................................... 9 Bluetooth Signals Hardware Details ..................................................................................... 10 WiFi Signals Hardware Details .............................................................................................. 10 Block Diagram ....................................................................................................................... 11 Features ................................................................................................................................ 11 Microcontroller ..................................................................................................................... 12 Software Features ................................................................................................................. 12 Package (Dimensions) ........................................................................................................... 14 Environmental Data, Quality & Reliability ............................................................................ 14 Electrical Characteristics ....................................................................................................... 14 Applications ........................................................................................................................... 15 Pin Compatible Wireless Variants ......................................................................................... 15 Supporting Products ............................................................................................................. 15 Placement Details ................................................................................................................. 16
KM-153103 Datasheet Page 3 List of Figures Figure 1: KM-153103 Koala® Connect Module ....................................................................................... 4 Figure 2: Module Pinouts ........................................................................................................................ 8 Figure 3: KM-153103 Module Block Diagram ....................................................................................... 11 Figure 4: Placement Details .................................................................................................................. 16 List of Tables Table 1: Product Selector ........................................................................................................................ 8 Table 2: Module Pinouts ......................................................................................................................... 9 Table 3: Bluetooth Signals Hardware Details ........................................................................................ 10 Table 4: WiFi Signals Hardware Details ................................................................................................. 10
KM-153103 Datasheet Page 4 Highlights • Complies with Part 15 of the FCC Rules • Wi-Fi & dual-mode Bluetooth • Supports custom Bluetooth Low Energy profiles and services • On-board Wi-Fi + Bluetooth antennas • Micro access point • High speed iAP & iAP2 support • Embedded Wi-Fi and Bluetooth stack • Use directly with final design or prototype on koala® evm with Clarinox Carrier boards. (KC-0181xx, KC-0081xx) Product Description Figure 1: KM-153103 Koala® Connect Module Joey® Wi-Fi® + Bluetooth® modules are compact all-in-one standalone modules featuring Wi-Fi WLAN / Wi-Fi Direct, Bluetooth Classic and Bluetooth Low Energy. When used in conjunction with koala® evm, the Joey® modules provide a stable environment to ease the integration of wireless technologies into a project. The modules feature Texas Instruments’ WL183xMOD variants with Wi-Fi and Bluetooth coexistence and STM32F412CG on-board processor to drive the user application in addition to supporting the wireless protocols. Flexibility of wireless technology is provided with version 4.1 Bluetooth Classic, Bluetooth Low Energy, WLAN and Wi-Fi Direct with IEEE802.11a/b/g/n standards supported. Joey® modules will help shorten the development time, reduce development costs and open the door to new possibilities for wireless device features. Joey® modules may be used stand-alone products with no additional hardware required; or used in conjunction with other hardware. Additional sensors can be connected directly to the module via GPIO, ADC, I2C, SPI and UART.
KM-153103 Datasheet Page 5 Module Certification Details KM-153103 Koala® Connect module complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. Clarinox Technologies declares that the radio equipment type RF module is in compliance with Directive 2014/53/EU. The compliance has been verified in the operating frequency band of 2400-2483.5 MHz. Developers and integrators that incorporate the KM-153103 Module in any end products are responsible for obtaining applicable regulatory approvals for such end product. The KM-153103 has been tested in the 2400 MHz-2483.5 MHz ISM frequency band at 3.3 V with a maximum peak power of 19.7 dBm EIRP across the temperature range –40°C to +85°C and tolerance. 1.2.1.1 Federal Communications Commission (FCC) Statement This module complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure limits. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 1.2.1.2 End Product Labelling This module is designed to comply with the FCC statement, FCC ID: 2AN5P1531. The host system using this module must display a visible label indicating the following text: "Contains FCC ID: 2AN5P1531" Important Notice to OEM Integrators This module is limited to OEM installation ONLY. This module is limited to installation in mobile or fixed applications, according to FCC Part 2.1091(b). The separate approval is required for all other operating configurations, including portable configurations with respect to FCC Part 2.1093 and different antenna configurations For FCC Part 15.31 (h) and (k): The host manufacturer is responsible for additional testing to verify compliance as a composite system. When testing the host device for compliance with Part 15 Subpart B, the host manufacturer is required to show compliance with Part 15 Subpart B while the transmitter module(s) are installed and operating. The modules should be transmitting and the evaluation should confirm that the module's intentional emissions are compliant (i.e. fundamental and out of band emissions). The host manufacturer must verify that there are no additional unintentional emissions other than what is permitted in Part 15 Subpart B or emissions are complaint with the transmitter(s) rule(s).
KM-153103 Datasheet Page 6 Antenna Installation The antenna must be installed such that 20 cm is maintained between the antenna and users, The transmitter module may not be co-located with any other transmitter or antenna. The ATN016008LCD2442MA1 antenna with -1.41 dBi gain was verified in the conformity testing. Radiated transmit power must be equal to or lower than that specified in the FCC Grant of Equipment Authorization for FCC ID: 2AN5P1531. A separate approval is required for all other antenna type, or higher gain antenna. In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
KM-153103 Datasheet Page 7 Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body.
KM-153103 Datasheet Page 8 Product Selector Table 1: Product Selector Module Pinouts Figure 2: Module Pinouts Model Radio Interfaces Power Package Bluetooth Qualification Bluetooth Classic and Low Energy WiFi Antenna Type Max Number of Connections UART SPI and I2C GPIO Pins ADC Channels Power Supply: 3.3V Current Draw (Idle) Current Draw (TX) I/O Voltage: 1.8V Solder Pins Dimensions (W x L x H) mm Support KC-0181xx Joeyduino Carrier Board Support KC-0081xx WMI Carrier Board KM-153103 V4.1 ✓ ✓ I 6-10 1 1 21 10 ✓ 60mA 90mA ✓ 32 20x34x3 ✓ ✓ KM-141202 V4.1 ✓ x I 6-10 1 1 23 10 ✓ 30mA 50mA ✓ 32 20x30x3.5 ✓ ✓
KM-153103 Datasheet Page 9 PIN FUNCTION SOURCE/TARGET PORT DETAILS P1 AUD_IN WL1831 AUD_IN (PCM) P2 AUD_OUT WL1831 AUD_OUT (PCM) P3 AUD_CLK WL1831 AUD_CLK (PCM) P4 AUD_FSYNC WL1831 AUD_FSYNC (PCM) P5 JTAG_TMS STM32F412 PA13 (JTAG) P6 JTAG _TCK STM32F412 PA14 (JTAG) P7 JTAG _TDI STM32F412 PA15 (JTAG) P8 JTAG _TDO STM32F412 PB3 (JTAG) P9 JTAG _JNRST STM32F412 PB4 (JTAG) P10 JTAG _NRST STM32F412 NRST (JTAG) P11 USB_FS_DP STM32F412 PA12 (USB FS/OTG) P12 USB_FS_DM STM32F412 PA11 (USB FS/OTG) P13 USB_FS_ID STM32F412 PA10 (USB FS/OTG) P14 USB_FS_VBUS STM32F412 PA9 (USB FS/OTG) P15 USB_FS_SOF STM32F412 PA8 (USB FS/OTG) P16 VBAT STM32F412 VDD (1V8) P17 GND STM32F412 VSS (GND) P18 GND STM32F412 VSS (GND) P19 3V3 Power Supply 3V3 P20 3V3 Power Supply 3V3 P21 GPIO_1 STM32F412 PB0 (GPIO) P22 GPIO_2 STM32F412 PB1 (GPIO) P23 NC P24 SPI1_MOSI STM32F412 PA7 (SPI) P25 SPI1_MISO STM32F412 PA6 (SPI) P26 SPI1_SCK STM32F412 PA5 (SPI) P27 SPI1_NSS STM32F412 PA4 (SPI) P28 I2C1_SMBA STM32F412 PB5 (I2C) P29 I2C1_SCL STM32F412 PB8 (I2C) P30 I2C1_SDA STM32F412 PB9 (I2C) P31 USART1_TX STM32F412 PB6 (USART) P32 USART1_RX STM32F412 PB7 (USART) Table 2: Module Pinouts Hardware Interfaces SPI 1 (4 pins) I2C 1 (3 pins) UART 1 (2 pins) PCM 1 (4 pins) GPIO pins 16* ADC channels 6
KM-153103 Datasheet Page 10 Bluetooth Signals Hardware Details WiLink8 Bluetooth module Microcontroller STM32F412 port BT EN (Bluetooth Enable) PC13 (Output) HCI RTS PA0 HCI CTS PA1 HCI RX PA2 HCI TX PA3 Table 3: Bluetooth Signals Hardware Details WiFi Signals Hardware Details Table 4: WiFi Signals Hardware Details WiLink8 WiFi module Microcontroller STM32F412 port WL_EN (Wi-Fi Enable) PB2 (Output) WL_IRQ (Wi-Fi IRQ) PB10 (Interrupt) SPI MISO PB14 SPI CLK PB13 SPI MOSI PB15 SPI CS PB12
KM-153103 Datasheet Page 11 Block Diagram Figure 3: KM-153103 Module Block Diagram Features Wi-Fi & Bluetooth module TI WL1831MOD Wi-Fi standards IEEE 802.11a/b/g/n, Wi-Fi Direct Concurrent Operation (Multichannel, Multirole) Wi-Fi bands 2.4 GHz Wi-Fi roles STA, AP, Wi-Fi Direct Wi-Fi maximum throughput TCP: 80 Mbps UDP: 100 Mbps Wi-Fi MIMO 2x2 MIMO Bluetooth modes V4.1 BR + EDR (Classic Bluetooth with EDR)
KM-153103 Datasheet Page 12 v4.1 LE (Bluetooth Low Energy) Output power Wi-Fi: +17.3 dBm (@ 1 Mbps DSSS) Classic Bluetooth: BR: +11.7 dBm (GFSK) EDR: +7.2 dBm Bluetooth LE: +7.0 dBm Sensitivity Wi-Fi: -96.3 dBm (@ 1 Mbps DSSS) Classic Bluetooth: -92.2 dBm (GFSK) Bluetooth LE: -92.2 dBm Antenna Internal antenna Microcontroller STM32F412CG Core: ARM® 32-bit Cortex®-M4 Package: UFQFPN48 CPU: 100 MHz SRAM: 256 Kbytes Flash: 1 Mbyte Software Features Embedded software ClarinoxBlue Bluetooth Stack ClarinoxBlue Bluetooth Low Energy Stack ClarinoxWiFi WLAN Stack (all combinations of the above three are possible) Combined IPv4 and limited IPv6 stack Supported Interfaces: ➢ UART ➢ I2C ➢ SPI ➢ USB Wi-Fi Security WEP 64/128 WPA and WPA2 TKIP and AES/CCMP hardware accelerator LEAP, PEAP, EAT-TLS Wi-Fi operational modes Access Point(AP) mode Station mode P2P (Wi-Fi Direct) Bluetooth Classic Profiles & Protocols Profiles: ➢ AVRCP Controller 1.5 ➢ A2DP Source | Sink 1.3 ➢ DID 1.3 ➢ FTP Client | Server 1.1 ➢ GAVDP Initiator | Acceptor | Delay Reporting Initiator 1.3 ➢ GOEP 1.1 ➢ HDP Source | Sink 1.1 ➢ HFP AG | HF 1.7 ➢ HID 1.1 General HID Host ➢ HSP AG | HS 1.2
KM-153103 Datasheet Page 13 ➢ IOP ➢ MAP 1.1 Messaging Client Equipment (MCE) ➢ MPS 1.0 ➢ OPP Client | Server 1.1 ➢ PAN User ➢ PBAP Client 1.2 ➢ Report Protocol | HID Device Role 1.1 ➢ SPP DevA| DevB 1.2 Protocols: ➢ AVCTP Controller 1.4 ➢ AVDTP Source | Sink | Initiator | Acceptor 1.3 ➢ BNEP ➢ GAP (Generic Access Profile)– BR/EDR/LE ➢ MCAP Source | Sink ➢ OBEX 1.1 ➢ OBEX over RFCOMM 1.1 ➢ RFCOMM 1.1 ➢ SDP (Service Discovery Protocol) Server | Client Bluetooth Low Energy Profiles & Protocols Profiles: ➢ ANP Server | Client 1.0 ➢ BAS Profile over LE ➢ BLP Sensor (Server) | Collector (Client) ➢ CPP Collector 1.0 ➢ CSCP Sensor (Server) | Collector (Client) ➢ CTS Profile over LE 1.0 ➢ DIS profile over LE 1.1 ➢ FMP Target (Server) | Locator (Client) ➢ GLP Sensor (Server) | Collector (Client) ➢ HIDS Profile over LE ➢ HOGP Device (Server) 1.0 ➢ HRP Sensor (Server) | Collector (Client) ➢ HRS Profile over LE ➢ HTP Thermometer (Server) | Collector (Client) ➢ IAS Profile over LE ➢ LNP Sensor (Server) | Collector (Client) 1.0 ➢ PASP Server ➢ PXP Reporter (Server) 1.0 ➢ RSCP Sensor (Server) ➢ TIP Server Protocols: ➢ ATT (Attribute Protocol) Client ➢ BPP (Basic Printing Profile) 1.2 Printer | Sender ➢ BIP (Basic Imaging Profile) 1.2 Image Push Initiator | Image Push Responder | Image Pull Initiator | Image Pull Responder ➢ CTN (Calendar, Tasks and Notes Profile) ➢ GAP (Generic Access Profile)– BR/EDR/LE ➢ GATT (Generic Attribute Profile) over LE Client | Server ➢ HCRP (Hardcopy Cable Replacement Profile) 1.2
KM-153103 Datasheet Page 14 Bluetooth Security Secure Simple Pairing 128-bit AES encryption BLE Secure Connection Max. number of connections Wi-Fi 2.4 GHz: Up to 8 connections Classic Bluetooth: Up to 7 connections Bluetooth LE: Up to 10 connections Single/Dual processor Approach User applications can be implemented on koala® connect with Clarinox WiFi / Bluetooth classic and low energy protocol stacks running on the same single CPU. Dual CPU approach is also possible by having Clarinox stacks implemented on koala® connect and user application running on a separate CPU. Using Joey® in both these approaches enhances IO capability in the system. Simultaneous Wireless usage Classic Bluetooth, Bluetooth Low Energy and Wi-Fi technologies can be used simultaneously and gateway functionality (simultaneous roles) amongst these technologies are possible API Interface Host to module connection supports Request-Response based implementation UART, I2C, SPI interfaces supported Applications can be simulated using a desktop environment Supported Wi-Fi modes AP, Station and P2P modes are supported Simultaneous nodes such as AP and Station are supported iOS connectivity iAP & iAP2 Package (Dimensions) Dimensions (W × L × H) 20 mm x 34 mm x 3 mm Weight < 2.0 g Mounting Solder edge pins with castellation (visually inspectable) Environmental Data, Quality & Reliability Operating temperature -10 °C to +60 °C Storage temperature -40 °C to +85 °C Electrical Characteristics Supply voltage 3.3 V I/O voltage 1.8 V Average Power consumption 0.15W Current draw (Bluetooth) Idle* 33mA Bluetooth Stack initialization 33mA Searching for devices 60mA Current draw (Wi-Fi) WiFi Stack initialization 90mA Start interface as Station 90mA Idle as Station 60mA Connect to Wi-Fi network as Station 110mA Start interface as Access Point (AP) 95mA
KM-153103 Datasheet Page 15 Idle as Access Point 60mA Connect to device as AP 160mA *Idle current is measured after Bluetooth is initialized while no any other functions are carried out. The current draw values in above table are the total current drawn by the Joey® module when connected to Clarinox Joeyduino Carrier. Applications Internet of Things (IoT) Consumer Electronics, Home Automation, Wearables Industrial IoT Industrial Automation Health Medical/Health devices Pin Compatible Wireless Variants KM-153103-1831 2.4 GHz Wi-Fi and Bluetooth KM-153103-1837 5 GHz and 2.4 GHz Wi-Fi and Bluetooth KM-153103-1801 2.4 GHz Wi-Fi only KM-153103-1807 5 GHz and 2.4 GHz Wi-Fi only Supporting Products KC-0181xx Joeyduino Carrier / Breakout Board for Joey® modules KC-0081xx WMI Carrier / Breakout Board for Joey® modules KM-9805xx Sensor Board with 9D sensor and haptic driver
KM-153103 Datasheet Page 16 Placement Details Figure 4: Placement Details

Navigation menu