Clarion 0608137 Car equipment unit User Manual manual

Clarion Co., Ltd Car equipment unit manual

manual

Clarion Co., Ltd.ConfidentialINSTRUCTION MANUAL OF UGZZ8-X021. BLUETOOTH MODULE SPECIFICATION1-1. PRODUCT NAMEUGZZ8-X021-2. MANUFACTURER ALPS ELECTRIC1-3. FEATURESBluetooth™ Specification V2.0+EDR supportComplete type of Bluetooth module, built-in various profileBuilt-in Link controller, Link Manager ProtocolOutput Power class2 compliantType with a chip antennaFull custom package with pwb can be fit to only navigation products made by ClarionBuilt-in Flash memory(16Mbit), system clock 26MHz(OSC)B to B connector interface1-4. SPECIFICATION1-4-1. MECHANICAL SPECIFICATION1-4-1-1. EXTERNAL DIMENSIONS Refer to the following page.1-4-1-2. MASS4.86 [g]1-4-2. ELECTRIC SPECIFICATION1-4-2-1. POWER-SUPPLY-VOLTAGE DC +3.1 to +3.6 [V]1-4-2-2. TEMPERATURE RANGE-40 to +85 [degree C]1-4-3. RF SPECIFICATION1-4-3-1. NORMAL TRANSMIT POWER(AVERAGED POWER)-6 to +4 [dBm]1-4-3-2. REFERENCE SENSITIVITY LEVEL(BER=0.001%)MAX. -70 [dBm]Chip AntennaTAIYO YUDENAF216M245001Coaxial Connectors with SwitchMurata ManufacturingMM8430-2610BtoB ConnectorMatsushita ElectricAXK620347YBLUETOOTH MODULEALPS ELECTRICUGZZ8-752AINSTRUCTION MANUAL OF UGZZ8-X02 - 1 / 5 -
Clarion Co., Ltd.Confidential1-5. LABEL INFORMATION1-5-1. LABEL LAYOUT1-5-2. CONTENTS OF LABEL1-6. CONNECTOR PIN ASSIGNMENTNO.PIN NAMENO.2GND-1VCCI4PIO[1] (PTE0)O3PIO[0] (PTB1)O6PCM_SYNCO5PDNO8GND-7PCM_OUTO10UART_CTSI9UART_RTSO12UART_TXO11UART_RXI14PCM_INI13PCM_CLKO16NCI15NCI18PIO[2] (PTE5)O17NCI20VCCI19RST#IDESCRIPTIONPower Supply 3.3VGroundAV Master Clock Select(44.1kHz=Low, 48kHz=High)PCM_Reset(Active Low), DAC PwrDown(PwrDown Enable=Low)HF/AV Status signalAudio Frame signalAV/HF OutputGroundUART_RTSUART_CTSUART_RXUART_TXAudio ClockAV/HF InputNCPower Supply 3.3VNCNCPCM_MuteReset(Active Low)UGZZ5-X02(Back View)BtoB Connector terminal NO.LabelModel: UGZZ8-X02IC: 419C-0608137UGZZ8-X02A (Back View)Model Number Rev. NumberClarion Parts NumberLot NumberTELEC Mark & IDCompany NameFCC ID & IC IDASJ20608137001WWDA1606060-8137-01Model: UGZZ8-X02: 419C-0608137INSTRUCTION MANUAL OF UGZZ8-X02 - 2 / 5 -
Clarion Co., Ltd.Confidential1-7. BLOCK DIAGRAM2. PROCEDURE TO BUILD IN2-1. PROCEDURE FOR UGZZ5-XO2(1)Install UGZZ8-X02 to BT-CAPAfter install UGZZ5-X02 to BT-CAP(BT-MODULE-AS)Slide to 4 points of Board-guide, and sandwich the module.(2)Connect BT-MODULE-AS to FRONT PCB by BtoB connectionTighten up a screw in order of one to two. After Connect BT-MODULE-AS to FRONT PCB by BtoB connection (FRONT-PCB-AS)SLIDEUGZZ8-X02BT-CAPFRONT PCBB to B connectionBOARD-GUIDEINSTRUCTION MANUAL OF UGZZ8-X02 - 3 / 5 -
Clarion Co., Ltd.Confidential(3)Install FRONT-PCB-AS to Navigation-unitConnect FRONT-PCB-AS to Navi-board by FCC cable connection.Tighten up a screw in order of one to four.(4)Install DVD-AS to Navigation-unit(5)Install UPPER-COVER to Navigation-unit(6)Install FRONT-COVER to Navigation-unit(7)Install REAR-COVER to Navigation-unitB to B connectionCONDUCTIVE SHEETChip Antenna positionUGZZ8-X02 installation positionINSTRUCTION MANUAL OF UGZZ8-X02 - 4 / 5 -
Clarion Co., Ltd.Confidential3. NOITCE-Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.-Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.-Please note that this users manual should not be provided to end-users.-The following sentence has to be displayed on the outside of the device in which the module is installed: "Contains Transmitter Module FCC ID: SJ20608137", or "Contains FCC ID: SJ20608137"-This equipment complies with FCC RF radiation exposure limits set for an controlled enviornment.-The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.INSTRUCTION MANUAL OF UGZZ8-X02 - 5 / 5 -

Navigation menu