Clarion 0608137 Car equipment unit User Manual manual

Download:
Mirror Download [FCC.gov]
Document ID	1632017
Application ID	dw2liBL1CU2XOvmXdPkIKg==
Document Description	manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	62.44kB (780534 bits)
Date Submitted	2012-02-07 00:00:00
Date Available	2012-02-10 00:00:00
Creation Date	2012-02-03 19:59:27
Producing Software	クセロPDF2 v2.10
Document Lastmod	2012-02-06 11:27:47
Document Title	manual
Document Creator	Xelo PDFLibrary

Clarion Co., Ltd.
Confidential
INSTRUCTION MANUAL OF UGZZ8-X02
1. BLUETOOTH MODULE SPECIFICATION
1-1. PRODUCT NAME
UGZZ8-X02
1-2. MANUFACTURER
ALPS ELECTRIC
1-3. FEATURES
Bluetoothâ„¢ Specification V2.0+EDR support
Complete type of Bluetooth module, built-in various profile
Built-in Link controller, Link Manager Protocol
Output Power class2 compliant
Type with a chip antenna
Full custom package with pwb can be fit to only navigation products made by Clarion
Built-in Flash memory(16Mbit), system clock 26MHz(OSC)
B to B connector interface
1-4. SPECIFICATION
1-4-1. MECHANICAL SPECIFICATION
1-4-1-1. EXTERNAL DIMENSIONS
Refer to the following page.
Chip Antenna
TAIYO YUDEN
AF216M245001
Coaxial Connectors with Switch
Murata Manufacturing
MM8430-2610
BtoB Connector
Matsushita Electric
AXK620347Y
BLUETOOTH MODULE
ALPS ELECTRIC
UGZZ8-752A
1-4-1-2. MASS
4.86 [g]
1-4-2. ELECTRIC SPECIFICATION
1-4-2-1. POWER-SUPPLY-VOLTAGE
DC +3.1 to +3.6 [V]
1-4-2-2. TEMPERATURE RANGE
-40 to +85 [degree C]
1-4-3. RF SPECIFICATION
1-4-3-1. NORMAL TRANSMIT POWER(AVERAGED POWER)
-6 to +4 [dBm]
1-4-3-2. REFERENCE SENSITIVITY LEVEL(BER=0.001%)
MAX. -70 [dBm]
INSTRUCTION MANUAL OF UGZZ8-X02 - 1 / 5 -
Clarion Co., Ltd.
Confidential
1-5. LABEL INFORMATION
1-5-1. LABEL LAYOUT
UGZZ8-X02A (Back
View)
UGZZ5-X02(Back
View)
Model: UGZZ8-X02
IC: 419C-0608137
Label
1-5-2. CONTENTS OF LABEL
Model Number
Clarion Parts Number
Model: UGZZ8-X02
Rev. Number
060-8137-01
TELEC Mark & ID
Lot Number
FCC ID & IC ID
SJ20608137
: 419C-0608137
001WWDA1606
Company Name
1-6. CONNECTOR PIN ASSIGNMENT
BtoB Connector terminal NO.
NO.
10
11
12
13
14
15
16
17
18
19
20
PIN NAME
VCC
GND
PIO[0] (PTB1)
PIO[1] (PTE0)
PDN
PCM_SYNC
PCM_OUT
GND
UART_RTS
UART_CTS
UART_RX
UART_TX
PCM_CLK
PCM_IN
NC
NC
NC
PIO[2] (PTE5)
RST#
VCC
NO.
DESCRIPTION
Power Supply 3.3V
Ground
AV Master Clock Select(44.1kHz=Low, 48kHz=High)
PCM_Reset(Active Low), DAC PwrDown(PwrDown Enable=Low)
HF/AV Status signal
Audio Frame signal
AV/HF Output
Ground
UART_RTS
UART_CTS
UART_RX
UART_TX
Audio Clock
AV/HF Input
NC
NC
NC
PCM_Mute
Reset(Active Low)
Power Supply 3.3V
INSTRUCTION MANUAL OF UGZZ8-X02 - 2 / 5 -
Clarion Co., Ltd.
Confidential
1-7. BLOCK DIAGRAM
2. PROCEDURE TO BUILD IN
2-1. PROCEDURE FOR UGZZ5-XO2
(1)Install UGZZ8-X02 to BT-CAP
BT-CAP
UGZZ8-X02
After install UGZZ5-X02 to BT-CAP
(BT-MODULE-AS)
BOARD-GUIDE
SLIDE
Slide to 4 points of Board-guide, and sandwich the module.
(2)Connect BT-MODULE-AS to FRONT PCB by BtoB connection
Tighten up a screw in order of one to two.
FRONT PCB
After Connect BT-MODULE-AS to FRONT PCB
by BtoB connection (FRONT-PCB-AS)
B to B connection
INSTRUCTION MANUAL OF UGZZ8-X02 - 3 / 5 -
Clarion Co., Ltd.
Confidential
(3)Install FRONT-PCB-AS to Navigation-unit
CONDUCTIVE SHEET
B to B connection
Connect FRONT-PCB-AS to Navi-board
by FCC cable connection.
Tighten up a screw in order of one to four.
(4)Install DVD-AS to Navigation-unit
(5)Install UPPER-COVER to Navigation-unit
(6)Install FRONT-COVER to Navigation-unit
(7)Install REAR-COVER to Navigation-unit
UGZZ8-X02 installation position
Chip Antenna position
INSTRUCTION MANUAL OF UGZZ8-X02 - 4 / 5 -
Clarion Co., Ltd.
Confidential
3. NOITCE
-Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
-Any changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
-Please note that this users manual should not be provided to end-users.
-The following sentence has to be displayed on the outside of the device in which the module is installed:
"Contains Transmitter Module FCC ID: SJ20608137", or "Contains FCC ID: SJ20608137"
-This equipment complies with FCC RF radiation exposure limits set for an controlled enviornment.
-The antenna used for this transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter.
INSTRUCTION MANUAL OF UGZZ8-X02 - 5 / 5 -

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Create Date                     : 2012:02:03 19:59:27+09:00
Creator Tool                    : Xelo PDFLibrary
Modify Date                     : 2012:02:06 11:27:47+09:00
Metadata Date                   : 2012:02:06 11:27:47+09:00
Producer                        : クセロPDF2 v2.10
Format                          : application/pdf
Document ID                     : uuid:ccef11ec-7d15-4989-9f95-7ba441096a34
Instance ID                     : uuid:7ea0e331-b940-4163-a4c4-31cb6dd79f5f
Page Count                      : 5
Creator                         : Xelo PDFLibrary

EXIF Metadata provided by EXIF.tools