Clarion CM1001 Bluetooth Car Kit User Manual printing FH10

Clarion (M) Sdn Bhd Bluetooth Car Kit printing FH10

user manual

CM-HS1 handsfree owners manualDo not install CM-HS1 on or near air conditioner duct to avoid condensation. Condensationwill result in some electronic component to malfunction, damaging the unit. Also, avoidinstalling the unit directly in the path of front speaker of the car stereo (voice route) tominimize echo.Pairing CM-HS1Before you start using CM-HS1 for the first time, you must pair it to your handphone. Pairingactivities differ from phone to phone. Please refer to handphone user documentation forpairing, and follow the steps below:1. Power on CM-HS1 by powering the car stereo unit. A Blue LED is lighted to indicate power.2. Simultaneously press the + and - buttons on CM-HS1. Blue and Red LEDs will blink to indicate readiness for pairing.3. Initiate Bluetooth pairing in the handphone to pair it with CM-HS1. To do this,please refer to the user documentation for the handphone.4. The default name is CM-HS1.5. When asked, the passkey is 0000. If pairing is successful, CM-HS1 will stop blinking, and only the Blue LED is lighted again.6. During usage (talking on the phone), both Blue and Red LEDs will be lighted(not blinking).Installing CM-HS1It is important that CM-HS1 is installed with the internal microphone facing towards the user(driver). Use the Visor Clip (included) to fix CM-HS1 to the car sun visor, and route the maincable properly. Use the special screw given to tighten CM HS1 to the Visor Clip if necessary.If installing CM-HS1 anywhere else, care must be taken so as not to damage the connectoron the unit. Test for the microphone strength during normal conversation and adjust thelocation accordingly.CM-HS1 handsfree owners manualFix CM-HS1 To The Car Sun Visor Fix CM-HS1 To The DashboardCM-HS1ScrewVisorClipCarSunVisor Main CableNote: Please check for the correct accessory before attempting to install CM-HS1 in your car. Please refer to Writing Diagram section for more details.What is CM-HS1?CM-HS1 is an In-Car hands free module offering a high-quality BluetoothTM wirelesscommunication solution for in-vehicles environment. The unit works with any BluetoothTMmobile telephone supporting headset profile version 1.0B/1.1.After initial setup, Bluetooth connection between handphone and CM-HS1 is automaticallyestablished when the ignition is switched on **. Incoming calls are accepted by pressingthe acceptance button. Muting the car stereo automatically, telephone sound is routedthrough car speaker.** Depending on telephone featuresGetting startedCM-HS1 handsfree owners manualVisor Clip Slot- ButtonInternal Microphone WindowMain CableConnectorAcceptance ButtonLED WindowExternal Microphone Input+ ButtonLETS START
1. Please refer to the diagram given for the correct wiring of CM-HS1. Incorrectwiring might damage the unit, your car stereo, or even your car. Please consulta professional.2. Check the features of the car stereo before installation. It is important to knowthe car stereo features, in order to choose the correct accessories.Wiring DiagramSystem requirements Mobile phone with BluetoothTM-supporting headset profileApprovals In accordance with the technical requirements of R&TTE for all EU countries and SwitzerlandCM-HS1 handsfree owners manual CM-HS1 handsfree owners manualWe : Clarion (M) SDN BHDPhase 3, FIZ11900 Bayan LepasPenang, Malaysia.declare under our sole responsibility that the following Product(s)MODEL: Bluetooth Car Hands free KitPart No(s): CM-HS1is (are) in conformity with the following relevent harmonised standards:EN 300328-2 (2001-12) - Electromagnetic compatibility and radio spectrum matters (ERM); Wideband Transmission systems operationin the 2.4GHz ISM band. Part 2 Essential requirements under Article3.2 of the RTTE directive.EN301489-3 (2001-11) - Electromagnetic compatibility and radio spectrum (ERM); EMC Standard for radio Equipment and services.Part 3 specific conditions for SRDs operating on frequencies between9kHz and 40GHzEN60950: 2000 - Information technology equipment Safety Part 1 General requirements.Following the provisions of Council Directive 1999/5/EC on radio equipmentand telecommunications terminal equipment and the mutual recognitionof their confirmity.Signature : Date : 1/11/2002Name: T.Nakazaki Position: R&D DirectorOn behalf of Clarion MalaysiaEC Declaration of ConformityFeaturesCM-HS1 handsfree owners manualTransfer standard Bluetooth 1.0B/1.1, conforms to profileFrequency range 2.4022.495 GHz, ISM band, license-freeRadio channels Fast frequency hopping, 79 channels, 1600 frequency changes/secondRange Sending performance 0 dBm (Class 3)~approximately 10mSensitivity 80 dBmProfile Headset profileInterface Main connector to car audio (Shielded 5 core cable.Power supply 5~6VOperating temperature -20C  80CStorage temperature -40C  105CTelephony operation Noise reduction, echo cancellation, full duplex telephonyDimensions Approx. 67 x 51 x 14mmWeight Approx. 22 gramsStatus display LEDs for display of the connection modePackage contents External microphone, control unit (Volume up/down, answercall button), interface box, Installation Guide,documentationAdjusting the Listening VolumeYou can adjust the speaker output volume during a call through CM-HS1.· To increase the volume, press the + button.· To decrease the volume, press the - button.Note: Use the + and - button to adjust volume, not the car stereo volume, to maximize echo cancellis circuit effectiveness.Receiving / Rejecting CallsPower on the car stereo. The unit works either when ACC on, or when the car stereo is turnon (please refer to Installation Guide for referance) to enable sound to be transferred tothe speaker. Press the acceptance button on CM-HS1 to receive a call. You can end acall by pressing the same button, or reject a call by pressing the same button twice.Voice DialingSome phone allows for voice dialing through CM-HS1. To do so, activate voice-dialingfeature in the handphone (consult your handphone documentation). Press the acceptancebutton to initiate voice dialing, and listen for the tone before starting. Say the voice tagname directly to CM-HS1.Important NotesFeatures vary according to phone makes and models. Some phone allows the user totransfer voice to CM-HS1, or to the phone for personal conversation. Some phone reconnectsdirectly to CM-HS1 every time you enter the car and start the engine. Please check forhandphone features to make full use of CM-HS1 capability.CM-HS1 handsfree owners manual

Navigation menu