Clarion CM1001 Bluetooth Car Kit User Manual printing FH10
Clarion (M) Sdn Bhd Bluetooth Car Kit printing FH10
Clarion >
user manual
Note: Please check for the correct accessory before attempting to install CM-HS1 in your car. Please refer to Writing Diagram section for more details. What is CM-HS1? TM CM-HS1 is an In-Car hands free module offering a high-quality Bluetooth wireless TM communication solution for in-vehicles environment. The unit works with any Bluetooth mobile telephone supporting headset profile version 1.0B/1.1. After initial setup, Bluetooth connection between handphone and CM-HS1 is automatically established when the ignition is switched on **. Incoming calls are accepted by pressing the acceptance button. Muting the car stereo automatically, telephone sound is routed through car speaker. ** Depending on telephone features Getting started Main Cable Connector Acceptance Button Visor Clip Slot - Button Internal Microphone Window LETS START Installing CM-HS1 It is important that CM-HS1 is installed with the internal microphone facing towards the user (driver). Use the Visor Clip (included) to fix CM-HS1 to the car sun visor, and route the main cable properly. Use the special screw given to tighten CM HS1 to the Visor Clip if necessary. If installing CM-HS1 anywhere else, care must be taken so as not to damage the connector on the unit. Test for the microphone strength during normal conversation and adjust the location accordingly. Fix CM-HS1 To The Car Sun Visor Visor Clip Fix CM-HS1 To The Dashboard Screw Car Sun Visor Main Cable CM-HS1 CM-HS1 handsfree owners manual LED Window External Microphone Input + Button CM-HS1 handsfree owners manual Do not install CM-HS1 on or near air conditioner duct to avoid condensation. Condensation will result in some electronic component to malfunction, damaging the unit. Also, avoid installing the unit directly in the path of front speaker of the car stereo (voice route) to minimize echo. Pairing CM-HS1 Before you start using CM-HS1 for the first time, you must pair it to your handphone. Pairing activities differ from phone to phone. Please refer to handphone user documentation for pairing, and follow the steps below: 1. Power on CM-HS1 by powering the car stereo unit. A Blue LED is lighted to indicate power. 2. Simultaneously press the + and - buttons on CM-HS1. Blue and Red LEDs will blink to indicate readiness for pairing. 3. Initiate Bluetooth pairing in the handphone to pair it with CM-HS1. To do this, please refer to the user documentation for the handphone. 4. The default name is CM-HS1. 5. When asked, the passkey is 0000. If pairing is successful, CM-HS1 will stop blinking, and only the Blue LED is lighted again. 6. During usage (talking on the phone), both Blue and Red LEDs will be lighted (not blinking). CM-HS1 handsfree owners manual Adjusting the Listening Volume You can adjust the speaker output volume during a call through CM-HS1. · To increase the volume, press the + button. · To decrease the volume, press the - button. Features Transfer standard Bluetooth 1.0B/1.1, conforms to profile Frequency range 2.4022.495 GHz, ISM band, license-free Note: Use the + and - button to adjust volume, not the car stereo volume, to maximize echo cancellis circuit effectiveness. Radio channels Fast frequency hopping, 79 channels, 1600 frequency changes/second Receiving / Rejecting Calls Power on the car stereo. The unit works either when ACC on, or when the car stereo is turn on (please refer to Installation Guide for referance) to enable sound to be transferred to the speaker. Press the acceptance button on CM-HS1 to receive a call. You can end a call by pressing the same button, or reject a call by pressing the same button twice. Range Sending performance 0 dBm (Class 3)~approximately 10m Sensitivity 80 dBm Profile Headset profile Interface Main connector to car audio (Shielded 5 core cable. Voice Dialing Some phone allows for voice dialing through CM-HS1. To do so, activate voice-dialing feature in the handphone (consult your handphone documentation). Press the acceptance button to initiate voice dialing, and listen for the tone before starting. Say the voice tag name directly to CM-HS1. Power supply 5~6V Important Notes Features vary according to phone makes and models. Some phone allows the user to transfer voice to CM-HS1, or to the phone for personal conversation. Some phone reconnects directly to CM-HS1 every time you enter the car and start the engine. Please check for handphone features to make full use of CM-HS1 capability. CM-HS1 handsfree owners manual LEDs for display of the connection mode Package contents External microphone, control unit (Volume up/down, answer call button), interface box, Installation Guide, documentation CM-HS1 handsfree owners manual T.Nakazaki On behalf of Clarion Malaysia Position: R&D Director Name: 1/11/2002 Date : Signature : Following the provisions of Council Directive 1999/5/EC on radio equipment and telecommunications terminal equipment and the mutual recognition of their confirmity. EN60950: 2000 - Information technology equipment Safety Part 1 General requirements. EN301489-3 (2001-11) - Electromagnetic compatibility and radio spectrum (ERM); EMC Standard for radio Equipment and services. Part 3 specific conditions for SRDs operating on frequencies between 9kHz and 40GHz EN 300328-2 (2001-12) - Electromagnetic compatibility and radio spectrum matters (ERM); Wideband Transmission systems operation in the 2.4GHz ISM band. Part 2 Essential requirements under Article 3.2 of the RTTE directive. is (are) in conformity with the following relevent harmonised standards: CM-HS1 handsfree owners manual Bluetooth Car Hands free Kit CM-HS1 1. Please refer to the diagram given for the correct wiring of CM-HS1. Incorrect wiring might damage the unit, your car stereo, or even your car. Please consult a professional. 2. Check the features of the car stereo before installation. It is important to know the car stereo features, in order to choose the correct accessories. Approx. 22 grams Status display MODEL: Part No(s): Wiring Diagram Approx. 67 x 51 x 14mm Weight declare under our sole responsibility that the following Product(s) In accordance with the technical requirements of R&TTE for all EU countries and Switzerland Noise reduction, echo cancellation, full duplex telephony Dimensions Clarion (M) SDN BHD Phase 3, FIZ 11900 Bayan Lepas Penang, Malaysia. Mobile phone with BluetoothTM-supporting headset profile Approvals -40C 105C Telephony operation We : System requirements Storage temperature EC Declaration of Conformity CM-HS1 handsfree owners manual Operating temperature -20C 80C
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.4 Linearized : No Create Date : 2003:02:28 03:13:23Z Modify Date : 2003:02:28 11:14:25+08:00 Page Count : 2 Creation Date : 2003:02:28 03:13:23Z Mod Date : 2003:02:28 11:14:25+08:00 Producer : Acrobat Distiller 5.0.5 (Windows) Author : jllim Metadata Date : 2003:02:28 11:14:25+08:00 Creator : jllim Title : printing.FH10EXIF Metadata provided by EXIF.tools