Clarion HGZ0024 Car equipment unit User Manual INSTRUCTION MANUAL OF UGZZ5 X02 FCC IC 2

Clarion Co., Ltd Car equipment unit INSTRUCTION MANUAL OF UGZZ5 X02 FCC IC 2

manual

㼄㼍㼚㼍㼢㼕㻌㻵㼚㼒㼛㼞㼙㼍㼠㼕㼏㼟㻌㻯㼛㼞㼜㼛㼞㼍㼠㼕㼛㼚㻯㻻㻺㻲㻵㻰㻱㻺㼀㻵㻭㻸INSTRUCTION MANUAL OF UGZZ5-X021. BLUETOOTH MODULE SPECIFICATION1-1. PRODUCT NAMEUGZZ5-X021-2. MANUFACTUREALPS ELECTRIC1-3. FEATURESBluetooth䉼Specification V1.2 supportComplete type of Bluetooth module, built-in various profileBuilt-in Link controller, Link Manager ProtocolOutput Power class2 compliantType with a chip antennaFull custom package with pwb can be fit to only navigation products made by XanaviBuilt-in Flash memory(8Mbit), system clock 26MHz(OSC)BtoBinterface1-4. SPECIFICATION1-4-1. MECHANICAL SPECIFICATION1-4-1-1. EXTERNAL DIMENSIONSRefer to the following page.1-4-1-2. MASS4.4 [g]1-4-2. ELECTRIC SPECIFICATION1-4-2-1. POWER-SUPPLY-VOLTAGEDC +3.1 to +3.5 [V]1-4-2-2. TEMPERATURE RANGE-30 to +85 [degree C]1-4-3. RF SPECIFICATION1-4-3-1. NORMAL TRANSMIT POWER(AVERAGED POWER)-6 to +4[dBm]1-4-3-2. REFERENCE SENSITIVITY LEVEL(BER=0.001%)MAX. -70 [dBm]Chip AntennaTAIYO YUDENAF216M245001Coaxial Connectors with SwitchMurata ManufacturingMM8430-2610BtoB ConnectorMatsushita ElectricAXK620347YBLUETOOTH MODULEALPS ELECTRICUGZZ5-611BINSTRUCTION MANUAL OF NAU-P8100EU - 1 / 5 -
㼄㼍㼚㼍㼢㼕㻌㻵㼚㼒㼛㼞㼙㼍㼠㼕㼏㼟㻌㻯㼛㼞㼜㼛㼞㼍㼠㼕㼛㼚㻯㻻㻺㻲㻵㻰㻱㻺㼀㻵㻭㻸1-5. LABEL INFORMATION1-5-1. LABEL LAYOUT1-5-2. CONTENTS OF LABEL1-6. CONNECTOR PIN ASSIGNMENT20 VCC I Power Supply 3.3V19 RESETP/IReset(Active Low)18 PTE5 O PCM_Mute17 BOOT_E IBOOT Enable16 PTA6 I MODE Select15 CLK11/12M I AV Master clock Input14 SIOF_RXD I AV/HF Input13 SIOF_SCK OAudio Clock12 SCIF0_TXD O UART_TX11 SCIF0_RXD IUART_RX10 SCIF0_CTS I UART_CTS9 SCIF0_RTS O UART_RTS8 GND - Ground7SIOF_TXDOAV/HF Output6 SIOF_SYNC O Audio Frame signal5PTA5OHF/AV Status signal4PTE0OPCM_Reset(Active Low)3 PTB1 O AV Master Clock Select(44.1kHz=Low, 48kHz=High)2 GND - Ground1 VCC I Power Supply 3.3VNO. PIN NAME NO. DESCRIPTIONUGZZ5-X02(Back View) LabelModel Number Rev. NumberXanavi Parts NumberLot NumberTELEC Mark & IDCompany NameFCC/IC IDBtoB Connector terminal NO.FCC ID: SJ2HGZ0024IC ID:5527A-HGZ0024FCC ID: SJ2HGZ0024IC ID:5527A-HGZ0024INSTRUCTION MANUAL OF NAU-P8100EU - 2 / 5 -
㼄㼍㼚㼍㼢㼕㻌㻵㼚㼒㼛㼞㼙㼍㼠㼕㼏㼟㻌㻯㼛㼞㼜㼛㼞㼍㼠㼕㼛㼚㻯㻻㻺㻲㻵㻰㻱㻺㼀㻵㻭㻸1-7. BLOCK DIAGRAM2. PROCEDURE TO BUILD IN2-1. PROCEDURE FOR UGZZ5-XO2(1)Install UGZZ5-X02 to BT-CAPAfter install UGZZ5-X02 to BT-CAP(BT-MODULE-AS)Slide to 4 points of Board-guide, and sandwich the module.(2)Connect BT-MODULE-AS to FRONT PCB by BtoB connectionTighten up a screw in order of one to two. After Connect BT-MODULE-AS to FRONT PCBby BtoB connection (FRONT-PCB-AS)SLIDEUGZZ5-X02BT-CAPFRONT PCBB to B connectionBOARD-GUIDEINSTRUCTION MANUAL OF NAU-P8100EU - 3 / 5 -
㼄㼍㼚㼍㼢㼕㻌㻵㼚㼒㼛㼞㼙㼍㼠㼕㼏㼟㻌㻯㼛㼞㼜㼛㼞㼍㼠㼕㼛㼚㻯㻻㻺㻲㻵㻰㻱㻺㼀㻵㻭㻸(3)Install FRONT-PCB-AS to Navigation-unitConnect FRONT-PCB-AS to Navi-boardby FCC cable connection.Tighten up a screw in order of one to four.(4)Install DVD-AS to Navigation-unit(5)Install UPPER-COVER to Navigation-unit(6)Install FRONT-COVER to Navigation-unit(7)Install REAR-COVER to Navigation-unitB to B connectionCONDUCTIVE SHEETChipAntennapositionUGZZ5-X02 installationpositionINSTRUCTION MANUAL OF NAU-P8100EU - 4 / 5 -
㼄㼍㼚㼍㼢㼕㻌㻵㼚㼒㼛㼞㼙㼍㼠㼕㼏㼟㻌㻯㼛㼞㼜㼛㼞㼍㼠㼕㼛㼚㻯㻻㻺㻲㻵㻰㻱㻺㼀㻵㻭㻸3. NOITCE-Operation is subject to the following two conditions:(1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation of the device.-Any changes or modifications not expressly approved by the party responsible for compliance could voidthe user's authority to operate the equipment.-Please note that this users manual should not beprovided to end-users.-The followingsentence has to be displayed on the outside of the device in which the module is installed:"Contains Transmitter Module FCC ID: SJ2HGZ0024", or "Contains FCC ID: SJ2HGZ0024"-This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.INSTRUCTION MANUAL OF NAU-P8100EU - 5 / 5 -

Navigation menu