Codan Radio Communications VT-3A130-S-FSH Transmitter User Manual Frequency Select Handle Instruction Manual

Codan Radio Communications Transmitter Frequency Select Handle Instruction Manual

Frequency Select Handle Instruction Manual

Download: Codan Radio Communications VT-3A130-S-FSH Transmitter User Manual Frequency Select Handle Instruction Manual
Mirror Download [FCC.gov]Codan Radio Communications VT-3A130-S-FSH Transmitter User Manual Frequency Select Handle Instruction Manual
Document ID95211
Application ID02cHfrORDT97QOPv6xeQbg==
Document DescriptionFrequency Select Handle Instruction Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize9.7kB (121270 bits)
Date Submitted2000-04-10 00:00:00
Date Available2000-05-09 00:00:00
Creation Date2000-04-06 09:23:10
Producing SoftwareAcrobat Distiller 4.0 for Macintosh
Document Lastmod2000-04-06 09:41:59
Document TitleFrequency Select Handle Instruction Manual

DANIELS
TM
ELECTRONICS LTD.
MT-3 RADIO SYSTEMS
FREQUENCY SELECT
HANDLE
INSTRUCTION MANUAL
Covers the following:
Frequency Select Handle portion of
VR-3A130-SYD210 & VT-3A130-SYD410
Copyright © 2000 Daniels Electronics Ltd. All rights reserved. No part of this publication may be
reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic,
mechanical, photocopying, recording or otherwise, without the prior written consent of Daniels
Electronics Ltd.
DE™ is a registered trademark of Daniels Electronics Ltd. registered in the United States Patent and
Trademark Office.
Issue:
Issue Date:
Printing Date:
Part No.:
Feb 2000
Feb 2000
IM12-FSH3
Previous Issue:
N/A
Previous Issue Date: N/A
Daniels Electronics Ltd.
Victoria, BC.
PRINTED IN CANADA
Reviewed By:
Quality Assurance:
Claudia Boorman
Name
Signature
_________________
Date
NOTE:
The user's authority to operate this equipment could be revoked through any
changes or modifications not expressly approved by Daniels Electronics Ltd.
The design of this equipment is subject to change due to continuous development.
This equipment may incorporate minor changes in detail from the information
contained in this manual.
DANIELS
DE ELECTRONICS
ii
Frequency Select Handle Instruction Manual
TABLE OF CONTENTS
Page
GENERAL ......................................................................................... 1-1
1.1 Introduction .................................................................................. 1-1
1.2 Printed Circuit Board Numbering Convention........................................... 1-1
1.3 Performance Specifications................................................................. 1-1
THEORY OF OPERATION ..................................................................... 2-1
2.1 General........................................................................................ 2-1
2.2 Handle Operation. ........................................................................... 2-1
ALIGNMENT ..................................................................................... 3-1
3.1 General........................................................................................ 3-1
3.2 Repair Note................................................................................... 3-1
3.3 Recommended Test Equipment ............................................................ 3-1
ILLUSTRATIONS AND SCHEMATIC DIAGRAMS....................................... 4-1
4.1 VR-3A130 Receiver Front Panel .......................................................... 4-1
4.2 Frequency Select Handle Component Layout............................................ 4-2
4.3 Frequency Select Handle Schematic Diagram............................................ 4-3
PARTS LISTS..................................................................................... 5-1
5.1 Frequency Select Handle Electrical Parts List............................................ 5-1
5.2 Frequency Select Handle Mechanical Parts List ......................................... 5-2
REVISION HISTORY............................................................................ 6-1
DANIELS
DE ELECTRONICS
Frequency Select Handle Instruction Manual
iii
This Page Intentionally Left Blank
DANIELS
DE ELECTRONICS
iv
Frequency Select Handle Instruction Manual
1
1.1
GENERAL
Introduction
The Frequency Select Handle provides the ability to select and display the operating frequency of
the receiver or transmitter on the Front Panel. Power is provided from a regulated +9.5 Vdc supply
and draws typically less than 4.0 mA in sleep mode.
1.2
Printed Circuit Board Numbering Convention
To ease troubleshooting and maintenance procedures, Daniels Electronics Limited has adopted a
printed circuit board (PCB) numbering convention in which the last two digits of the circuit board
number represent the circuit board version. For example:
• PCB number 43-912010 indicates circuit board version 1.0.
• PCB number 50002-02 indicates circuit board version 2.0.
All PCB's manufactured by Daniels Electronics are identified by one of the above conventions.
1.3
Performance Specifications
Temperature Range:
-30°C to +60°C. (Optional -40°C to +60°C)
Supply Voltage:
+9.5 Vdc,
Supply Current:
less 35 mA
less 4.0 mA standby mode.
DANIELS
DE ELECTRONICS
Frequency Select Handle Instruction Manual
1-1
This Page Intentionally Left Blank
DANIELS
DE ELECTRONICS
1-2
Frequency Select Handle Instruction Manual
2
THEORY OF OPERATION
2.1
General
The user interface consists of an 8 digit display and 3 pushbuttons, frequency increase Ø,
frequency decrease Œ, and options ¸. On power up or key press, the synthesizer is interrogated
for the current channel number and channel frequency. This information is used to generate the
display, and update the synthesizer itself.
The Frequency Select Handle communicates with the synthesizer using a standard 2 wire serial
interface (9600 Baud, 8 bits, no parity, 1 stop bit). The command protocols are simple ASCII,
both to and from the synthesizer. Another dedicated line allows the handle to temporarily wake up
the synthesizer if it has been powered down. (This is currently only used on the transmitters)
The Frequency Select Handle is built around a PIC microcontroller and is powered from regulated
9.5 Vdc.
2.2
Handle Operation.
1) On Power Up the following front panel indications will occur: (in order)
•
•
•
•
Daniels Banner ("Daniels Electronics Ltd") will scroll by.
The current Channel Number will be displayed (for about 2 sec).
The current Operating Frequency will be displayed ( for about 2 sec)
The display then does to sleep.
2) To display the Current Frequency:
a) Press either the Ø (Frequency increase) or Œ (Frequency decrease) buttons
This will display the current Channel Number (for about 2 sec), then the current frequency
(for about 3 sec) The display will then go back to sleep.
b) To keep the display awake, just press the Ø or Œ buttons again before the display has
gone back to sleep. This will display the frequency for another 2-3 sec.
3) To change the Programmable Channel operating frequency (channel 16 only)
a) Press either Ø or Œ buttons to wake up the display.
b) Then use Ø or Œ buttons to change the frequency. ( Note the buttons must be unlocked to
be used. See (4) below.
DANIELS
DE ELECTRONICS
Frequency Select Handle Instruction Manual
2-1
c) Both the Ø or Œ have two modes of operation.
i. Single press is for small changes. Single button presses corresponds to single channel
( 25 kHz) steps.
ii. Accelerated is for large steps. After 6 seconds of the button being pressed the
frequency will change by8 channels per step (200 kHz). After 9 seconds of the button
being pressed the frequency will change by 20 channels per step (500 kHz).
Note: The operating frequency is set to displayed value once the Ø or Œ buttons is released.
4) To Lock / Unlock the Buttons.
a) Press the ¸ button. The display will show the current lock status ("Locked" or
"Unlocked")
b) To lock the buttons, press the Ø button ( the display will then show "Locked")
c) To unlock the buttons, press the Œ button (the display will then show "Unlocked")
Note: To display the current channel and frequency, the display must be allowed to go to sleep.
DANIELS
DE ELECTRONICS
2-2
Frequency Select Handle Instruction Manual
3
3.1
ALIGNMENT
General
Under normal circumstances no alignment is required to the Frequency Select Handle.
3.2
Repair Note
The Frequency Select Handle employs a high percentage of surface mount components, which
should not be removed or replaced using an ordinary soldering iron. Removal and replacement of
surface mount components should be performed only with specifically designed surface mount
rework and repair stations complete with Electro Static Dissipative (ESD) protection.
3.3
Recommended Test Equipment
• Power supply - Regulated +9.5 Vdc at 0.1 A. Phillips PM 2811
DANIELS
DE ELECTRONICS
Frequency Select Handle Instruction Manual
3-1
This Page Intentionally Left Blank
DANIELS
DE ELECTRONICS
3-2
Frequency Select Handle Instruction Manual
4
ILLUSTRATIONS AND SCHEMATIC DIAGRAMS
4.1
VR-3A130 Receiver Front Panel
RECE I VER
MADE IN CANADA
RECEIVER
MODEL IDENTIFIER
MADE IN CANADA
VR-3A130-SYD210
SQUELCH DISABLE
SQ . DI SABLE
ON / OFF SWITCH
N O RM
O FF
RF IN
REFERENCE
TYPE N RF
INPUT JACK
SMA REFERENCE
INPUT JACK
INPUT
Daniels Electronics Ltd
FREQUENCY
INDICATOR
FREQUENCY
INCREASE BUTTON
OPTIONS BUTTON
FREQUENCY
DECREASE BUTTON
AM3RXM1A
DANIELS
DE ELECTRONICS
Frequency Select Handle Instruction Manual
4-1
4.2
Frequency Select Handle Component Layout
U2
PDSP 1881
R8
10K
SW3
C5
100nF
R9
10K
C3
22uF
U3
78L05
C4
100nF
R7
10K
R1
10K
SW2
R6
475
D5
BAS16
R4
6K8
C2
22pF
D6
BAS16
SW1
D4
BAS16
C1
22pF
U1
16C63A
X1
8MHz
R5
10K
D3
BAS16
R2
10K
R3
10K
D1
BAS16
D2
BAS16
PCB 50088-04
FSH3M1
DANIELS
DE ELECTRONICS
4-2
Frequency Select Handle Instruction Manual
4.3
Frequency Select Handle Schematic Diagram
+5Vdc
U2
PDSP1881
15
16
Vcc
D7
D0
18
GND
A4
30 29 28 27 26 25 21 20
/RD /FL
/WR /CE /RST CLS CLK
A0
10 6
13 19 14 2
11
12
+5Vdc
R8
10K0
A0
A1
A2
A3
A4
D0
D1
D2
D3
D4
+5Vdc
D5
D6
+5Vdc
R5
10K0
D3
BAS16
+5Vdc
D4
BAS16
U1
16C63A
+5Vdc
20
Vcc
R2
10K0
R3
10K0
/CE
11
/RD
12
/WR
13
14
15
SW1
Up
SW2
Down
SW3
Option
16
17
18
D1
BAS16
D2
BAS16
10
Rc0
Rb0
Rc1
Rb1
Rc2
Rb2
Rc3
Rb3
Rc4
Rb4
Rc5
Rb5
Rc6
Rb6
Rc7
21
Rb7
Ra0
OSC1
Ra1
Ra2
OSC2
Ra3
X1
8 MHz
C1
22pF
Ra4
C2
22pF
Gnd
D0
23
D1
24
D2
25
D3
26
D4
27
D5
28
D6
A0
A1
A2
A3
A4
Ra5
MCLR
22
Gnd
19
+5Vdc
R1
10K0
+5Vdc
R4
6K81
+5Vdc
C5
100nF
U3
78L05
+5Vdc
+5Vdc
R9
10K0
C3
22uF
R7
10K0
IN
OUT
GND
C4
100nF
J1
J2 Sin
J3 Sout
J4 Power Up
R6
0R0
D5
BAS16
D6
BAS16
J5
HIGHEST REFERENCE DESIGNATORS
-----
-----
-----
-----
-----
-----
-----
-----
-----
UNUSED REFERENCE DESIGNATORS
DANIELS
VICTORIA B.C.
ELECTRONICS LTD.
TITLE:
FREQUENCY SELECT HANDLE SCHEMATIC DIAGRAM
-----
-----
-----
DATE: 01 December 99
-----
-----
-----
DWG No: FSH3M2B
DWN BY: Paul Ellis
DWG REV DATE:
-----
-----
-----
BOARD No: 50088-04
BOARD REV: V 04
APRVD:
DANIELS
ELECTRONICS LTD.
Frequency Select Handle Instruction Manual
4-3
This Page Intentionally Left Blank
DANIELS
DE ELECTRONICS
4-4
Frequency Select Handle Instruction Manual
5
PARTS LISTS
5.1
Frequency Select Handle Electrical Parts List
Ref.
Desig
Description
Part No.
C1, C2
C3
C4, C5
CAP., SM, 22pF CER., 0805, C0G
CAP., 22uF DIP. TANT., 20%,20V
CAP., SM,100nF CER,0805,X7R,50
1008-1A220J1G
1054-6G226M20
1008-5A104K5R
D1-D6
DIODE, BAS16, SWITCHING, SOT23
2100-BAS16000
PCB
PCB, FREQUENCY SELECT HANLE
4312-90500884
R1-R3
R4
R5
R6
R7-R9
RES.,
RES.,
RES.,
RES.,
RES.,
SM, 10K0 0805, 1%,100ppm
SM, 6K81 0805, 1%,100ppm
SM, 10K0 0805, 1%,100ppm
SM., ZERO OHM JUMPER.
SM, 10K0 0805, 1%,100ppm
1150-4A1002FP
1150-3A6811FP
1150-4A1002FP
1150-0A0R0000
1150-4A1002FP
SW1-SW3
SWITCH, SM/PB, SPST/MOM,SEALED
5238-309J05NW
U1
U2
U3
IC, PIC16C63A-20I,M/CTR,SSOP28
DISPLAY, 8CHAR,5x7 DOT MTX,YEL
IC, 78L05AB, +5.OV REG., TO-92
2380-16C63S28
2018-D857330Y
2205-78053T92
X1
RESONATOR, SM, 8.0MHz, CERAMIC
1575-8001816A
DANIELS
DE ELECTRONICS
Frequency Select Handle Instruction Manual
5-1
5.2
Frequency Select Handle Mechanical Parts List
Description
Part No.
Qty.
HOUSING, 0.1",5 POS.,MALE TERM
HOUSING, 0.1",5 POS.,FEM. TERM
5021-HM05L001
5021-HF05L002
LABEL,
3537-40121010
SHIELD,
3702-67201305
TERMINAL, CRIMP, MALE,22-24,Au
TERMINAL, CRIMP, FEM.,22-24,Au
5021-TM22B001
5021-TF22B002
WIRE, PVC/STRAND., 22AWG,BLACK
WIRE, PVC/STRAND., 22AWG, RED
WIRE, PVC/STRAND., 22AWG, ORG.
WIRE, PVC/STRAND.,22AWG,YELLOW
WIRE, PVC/STRAND., 22AWG, VIO.
7110-22S07300
7110-22S07302
7110-22S07303
7110-22S07304
7110-22S07307
18 cm
18 cm
18 cm
18 cm
18 cm
DANIELS
DE ELECTRONICS
5-2
Frequency Select Handle Instruction Manual
6
REVISION HISTORY
ISSUE DATE
DESCRIPTION AND (REASON)
• Issue 1
Feb 00
DANIELS
DE ELECTRONICS
Frequency Select Handle Instruction Manual
6-1
This Page Intentionally Left Blank
DANIELS
DE ELECTRONICS
6-2
Frequency Select Handle Instruction Manual

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : No
Create Date                     : 2000:04:06 09:23:10
Producer                        : Acrobat Distiller 4.0 for Macintosh
Modify Date                     : 2000:04:06 09:41:59-07:00
Page Count                      : 18
EXIF Metadata provided by EXIF.tools
FCC ID Filing: H4JVT-3A130-S-FSH

Navigation menu