Comtrend VR3060U Wireless Gateway User Manual UM VR3060 addingEMC 160909

Comtrend Corporation Wireless Gateway UM VR3060 addingEMC 160909

Contents

User Manual-1

261099-038 VR-3060u, VR-3060 Wireless Gateway User Manual Version A1.0, December 22, 2015
1 Preface This manual provides information related to the installation and operation of this device. The individual reading this manual is presumed to have a basic understanding of telecommunications terminology and concepts. If you find the product to be inoperable or malfunctioning, please contact technical support for immediate service by email at INT-support@comtrend.com For product update, new product release, manual revision, or software upgrades, please visit our website at http://www.comtrend.com Important Safety Instructions With reference to unpacking, installation, use, and maintenance of your electronic device, the following basic guidelines are recommended: • Do not use or install this product near water, to avoid fire or shock hazard. For example, near a bathtub, kitchen sink or laundry tub, or near a swimming pool. Also, do not expose the equipment to rain or damp areas (e.g. a wet basement). • Do not connect the power supply cord on elevated surfaces. Allow it to lie freely. There should be no obstructions in its path and no heavy items should be placed on the cord. In addition, do not walk on, step on, or mistreat the cord. • Use only the power cord and adapter that are shipped with this device. • To safeguard the equipment against overheating, make sure that all openings in the unit that offer exposure to air are not blocked. • Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightening. Also, do not use the telephone to report a gas leak in the vicinity of the leak. • Never install telephone wiring during stormy weather conditions. CAUTION:  To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord.  Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment. WARNING  Disconnect the power line from the device before servicing.  Power supply specifications are clearly stated in Appendix C - Specifications.
2 FCC & ISED User Information Any changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment. Aucune modification apportée à l’appareil par l’utilisateur, quelle qu’en soit la nature. Tout changement ou modification peuvent annuler le droit d’utilisation de l’appareil par l’utilisateur. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged totry to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected. —Consult the dealer or an experienced radio/TV technician for help. This Class B digital apparatus complies with Canadian ICES-003. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful communication. This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: 1. This device may not cause interference, and 2. This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil numérique de la classe B est conforme à la norme NMB-003 Canada. Pour réduire le risque d’interférence aux autres utilisateurs, le type d’antenne et son gain doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) ne dépasse pas ce qui est nécessaire pour une communication réussie. Cet appareil est conforme à la norme RSS Industrie Canada exempts de licence norme(s). Son fonctionnement est soumis aux deux conditions suivantes: 1. Cet appareil ne peut pas provoquer d’interférences et 2. Cet appareil doit accepter toute interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement du dispositif.
3 Radiation Exposure FCC ID: L9VVR3060U IC: 4013A-VR3060U US: 5SYDL01ANL3240U REN: 0.1A FCC 1. This Transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. ISED This device complies with the ISED radiation exposure limit set forth for an uncontrolled environment. This device should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cet équipement est conforme avec l'exposition aux radiations ISED définies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à une distance minimum de 20 cm entre le radiateur et votre corps. Cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec une autre antenne ou transmetteur. Operations in the 5.15-5.25Ghz band are restricted to indoor usage only. Le fonctionnement sur la bande 5,15–5,25Ghz est limité à une utilisation intérieure uniquement. This radio transmitter (identify the device by certification number) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Model Name: AN2450-64D02BBO Type: External Gain: 2.4G: 2.5 dBi 5G: 2.5 dBi Model Name: AN2450-64D03BBO Type: External Gain:
4 2.4G: 1.2 dBi 5G: 2.5 dBi The REN statement is the following: "The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to a telephone interface. The termination of an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed five." Copyright Copyright©2015 Comtrend Corporation. All rights reserved. The information contained herein is proprietary to Comtrend Corporation. No part of this document may be translated, transcribed, reproduced, in any form, or by any means without prior written consent of Comtrend Corporation. This program is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. This program is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see http://www.gnu.org/licenses/ NOTE: This document is subject to change without notice. Protect Our Environment This symbol indicates that when the equipment has reached the end of its useful life, it must be taken to a recycling centre and processed separate from domestic waste. The cardboard box, the plastic contained in the packaging, and the parts that make up this router can be recycled in accordance with regionally established regulations. Never dispose of this electronic equipment along with your household waste; you may be subject to penalties or sanctions under the law. Instead, please be responsible and ask for disposal instructions from your local government.
5 Table of Contents CHAPTER 1 INTRODUCTION ........................................................................................................... 8CHAPTER 2 INSTALLATION ............................................................................................................. 92.1 HARDWARE SETUP ........................................................................................................................... 92.2 LED INDICATORS .......................................................................................................................... 11CHAPTER 3 WEB USER INTERFACE ............................................................................................ 133.1 DEFAULT SETTINGS ....................................................................................................................... 133.2 IP CONFIGURATION ........................................................................................................................ 143.3 LOGIN PROCEDURE ........................................................................................................................ 16CHAPTER 4 DEVICE INFORMATION ........................................................................................... 184.1 WAN ............................................................................................................................................. 204.2 STATISTICS ..................................................................................................................................... 214.2.1LAN Statistics ................................................................................................................. 214.2.2WAN Service ................................................................................................................... 224.2.3XTM Statistics ................................................................................................................. 234.2.4xDSL Statistics ................................................................................................................ 244.3 ROUTE ........................................................................................................................................... 294.4 ARP............................................................................................................................................... 304.5 DHCP ........................................................................................................................................... 304.6 NAT SESSION ................................................................................................................................ 324.7 IGMP INFO .................................................................................................................................... 334.8 IPV6 .............................................................................................................................................. 344.8.1 IPv6 Info ................................................................................................................................ 344.8.2 IPv6 Neighbor ....................................................................................................................... 354.8.3 IPv6 Route ............................................................................................................................. 364.9 CPU & MEMORY ........................................................................................................................... 374.10 NETWORK MAP ........................................................................................................................... 384.11 WIRELESS .................................................................................................................................... 384.11.1 Station Info ........................................................................................................................... 384.11.2 Site Survey............................................................................................................................ 40CHAPTER 5 BASIC SETUP ............................................................................................................... 425.1 WAN SETUP ................................................................................................................................... 435.1.1 WAN Service Setup ................................................................................................................ 445.2 NAT .............................................................................................................................................. 455.2.1Virtual Servers ................................................................................................................ 455.2.2Port Triggering ............................................................................................................... 475.2.3DMZ Host ....................................................................................................................... 495.2.4 IP Address Map............................................................................................................... 505.2.5 ALG/Pass-Through ......................................................................................................... 515.3 LAN .............................................................................................................................................. 525.3.1 LAN IPv6 Autoconfig ............................................................................................................. 555.3.2 Static IP Neighbor ................................................................................................................. 585.3.3 UPnP ..................................................................................................................................... 595.4 WIRELESS ...................................................................................................................................... 605.4.1 Basic 5GHz ............................................................................................................................ 605.4.2 Security 5GHz ........................................................................................................................ 625.4.3 Basic 2.4GHz ......................................................................................................................... 655.4.4 Security 2.4GHz ..................................................................................................................... 675.5 PARENTAL CONTROL ..................................................................................................................... 705.5.1Time Restriction .............................................................................................................. 705.5.2URL Filter ....................................................................................................................... 715.6 HOME NETWORKING ...................................................................................................................... 735.6.1 Print Server ........................................................................................................................... 735.6.2 DLNA ..................................................................................................................................... 735.6.3 Storage Service ...................................................................................................................... 745.6.4 USB Speed ............................................................................................................................. 75
6 CHAPTER 6 ADVANCED SETUP ..................................................................................................... 766.1 AUTO-DETECTION SETUP ............................................................................................................... 766.2 SECURITY ...................................................................................................................................... 816.2.1IP Filtering ..................................................................................................................... 816.2.2 MAC Filtering ................................................................................................................. 856.3 QUALITY OF SERVICE (QOS) .......................................................................................................... 876.3.1QoS Queue ...................................................................................................................... 886.3.1.1QoS Queue Configuration .............................................................................................. 886.3.1.2Wlan Queue .................................................................................................................... 926.3.2 QoS Classification .......................................................................................................... 936.3.3 QoS Port Shaping ........................................................................................................... 956.4 ROUTING ....................................................................................................................................... 966.4.1Default Gateway ............................................................................................................. 966.4.2Static Route ..................................................................................................................... 976.4.3Policy Routing ................................................................................................................ 986.4.4RIP .................................................................................................................................. 996.5 DNS ............................................................................................................................................ 1006.5.1DNS Server ................................................................................................................... 1006.5.2Dynamic DNS ............................................................................................................... 1016.5.3 DNS Entries .................................................................................................................. 1026.5.4 DNS Proxy/Relay .......................................................................................................... 1036.6 DSL ............................................................................................................................................. 1046.7 INTERFACE GROUPING ................................................................................................................. 1066.8 IP TUNNEL ................................................................................................................................... 1096.8.1 IPv6inIPv4 ........................................................................................................................... 1096.8.2 IPv4inIPv6 ........................................................................................................................... 1106.9 CERTIFICATE ................................................................................................................................ 1116.9.1Local ............................................................................................................................. 1116.9.2Trusted CA .................................................................................................................... 1136.10 POWER MANAGEMENT .............................................................................................................. 1146.11 MULTICAST ................................................................................................................................ 1156.12 WIRELESS .................................................................................................................................. 1176.12.1 Basic 5GHz ........................................................................................................................ 1176.12.2 Security 5GHz .................................................................................................................... 1196.12.3 WPS 5GHz ......................................................................................................................... 1226.12.4 MAC Filter 5GHz .............................................................................................................. 1256.12.5 Wireless Bridge .................................................................................................................. 1266.12.6 Advanced 5GHz ................................................................................................................. 1276.12.7 Basic 2.4GHz ..................................................................................................................... 1316.12.8 Security 2.4GHz ................................................................................................................. 1336.12.9 WPS 2.4GHz ...................................................................................................................... 1366.12.10 MAC Filter 2.4GHz ......................................................................................................... 1396.12.11 Wireless Bridge 2.4GHz ................................................................................................... 1416.12.12 Advanced 2.4GHz ............................................................................................................ 142CHAPTER 7 DIAGNOSTICS ........................................................................................................... 1457.1 DIAGNOSTICS – INDIVIDUAL TESTS ............................................................................................. 1457.2 ETHERNET OAM ......................................................................................................................... 1467.3 UPTIME STATUS ........................................................................................................................... 1487.4 PING ............................................................................................................................................ 1497.5 TRACE ROUTE ............................................................................................................................. 150CHAPTER 8 MANAGEMENT ........................................................................................................ 1518.1 SETTINGS ..................................................................................................................................... 1518.1.1Backup Settings ............................................................................................................. 1518.1.2Update Settings ............................................................................................................. 1528.1.3Restore Default ............................................................................................................. 1528.2 SYSTEM LOG ............................................................................................................................... 1548.3 SNMP AGENT ............................................................................................................................. 1568.4 TR-069 CLIENT ........................................................................................................................... 1578.5 INTERNET TIME ........................................................................................................................... 159
7 8.6 ACCESS CONTROL ....................................................................................................................... 1608.6.1 Accounts ........................................................................................................................... 1608.6.2 Services ............................................................................................................................. 1628.6.3 IP Address ......................................................................................................................... 1638.7 WAKE-ON-LAN ........................................................................................................................... 1648.8 UPDATE SOFTWARE ..................................................................................................................... 1658.9 REBOOT ....................................................................................................................................... 166CHAPTER 9 LOGOUT ..................................................................................................................... 167APPENDIX A - FIREWALL ............................................................................................................. 168APPENDIX B - PIN ASSIGNMENTS .............................................................................................. 171APPENDIX C – SPECIFICATIONS ................................................................................................ 172APPENDIX D - SSH CLIENT .......................................................................................................... 174APPENDIX E - PRINTER SERVER ................................................................................................ 175APPENDIX F - CONNECTION SETUP .......................................................................................... 181
8 Chapter 1 Introduction VR-3060 is a Multi-DSL solution for high-performance Internet access. In addition, VR-3060 supports high power (400mw/26 dBm) dual bands (802.11n 2.4GHz & 802.11ac 5GHz) to create a large Wi-Fi footprint for the most seamless video experience as well as blazing fast data speed and a toll-quality voice experience.
9 Chapter 2 Installation 2.1 Hardware Setup Follow the instructions below to complete the hardware setup. Non-stackable This device is not stackable – do not place units on top of each other, otherwise damage could occur. BACK PANEL The figure below shows the back panel of the device. Power ON Press the power button to the OFF position (OUT). Connect the power adapter to the power port. Attach the power adapter to a wall outlet or other AC source. Press the power button to the ON position (IN). If the Power LED displays as expected then the device is ready for setup (see section 2.2 LED Indicators). Caution 1: If the device fails to power up, or it malfunctions, first verify that the power cords are connected securely and then power it on again. If the problem persists, contact technical support. Caution 2: Before servicing or disassembling this equipment, disconnect all power cords and telephone lines from their outlets. Reset Button Restore the default parameters of the device by pressing the Reset button for 10 seconds. After the device has rebooted successfully, the front panel should display as expected (see section 2.2 LED Indicators for details). NOTE: If pressed down for more than 60 seconds, the VR-3060 will go into a firmware update state (CFE boot mode). The firmware can then be updated using an Internet browser pointed to the default IP address.
10 ETH WAN PORT This port has the same features as the LAN ports described below with additional Ethernet WAN functionality. Ethernet (LAN) Ports Use 1000-BASE-T RJ-45 cables to connect up to four network devices to a Gigabit LAN, or 10/100BASE-T RJ-45 cables for standard network usage. These ports are auto-sensing MDI/X; so either straight-through or crossover cable can be used. USB Host Port (Type A) This port can be used to connect the router to a printer, or supported USB devices. DSL Port Connect to an ADSL2/2+ or VDSL with this RJ11 Port. This device contains a micro filter which removes the analog phone signal. If you wish, you can connect a regular telephone to the same line by using a POTS splitter. FRONT PANEL 2.4G WiFi On/Off & WPS Button Press and release the WiFi-WPS button to activate WPS for the 2.4GHz WiFi interface (make sure the WPS is enabled in Wireless->2.4GHz->Security page).Press and hold WiFi-WPS button more than 10 seconds to enable/disable 2.4GHz WiFi. 5G WiFi On/Off & WPS Button Press and release the WiFi-WPS button to activate WPS for the 5GHz WiFi interface (make sure the WPS is enabled in Wireless->5GHz->Security page).Press and hold WiFi-WPS button more than 10 seconds to enable/disable 5GHz WiFi.
11 2.2 LED Indicators The front panel LED indicators are shown below and explained in the following table. This information can be used to check the status of the device and its connections. LED Color Mode Function POWER GREEN On The device is powered up. Off The device is powered down. RED On POST (Power On Self Test) failure or other malfunction. A malfunction is any error of internal sequence or state that will prevent the device from connecting to the DSLAM or passing customer data. ETH WAN GREEN On WAN is connected in 1000 Mbps. Off Ethernet WAN is not connected. Blink In TX/RX over 1000 Mbps ORANGE On Ethernet is connected in 10/100 Mbps. Off Ethernet WAN is not connected. Blink In TX/RX over 10/100 Mbps. ETH 4 to 1 GREEN On Ethernet is connected at 1000 Mbps. Off Ethernet is not connected. Blink In TX/RX over 1000 Mbps. ORANGE On Ethernet is connected at 10/100 Mbps. Off Ethernet is not connected. Blink In TX/RX over 10/100 Mbps. WPS GREEN On WPS(2.4G) WPS enabled and client connected to WLAN. Off WPS(2.4G) WPS disabled. Blink WPS(2.4G) WPS connection in progress, 120 seconds or until client connected. ORANGE On WPS(5G WPS enabled and client connected to WLAN. Off WPS(5G) WPS disabled. Blink WPS(5G) WPS connection in progress, 120 seconds or until client connected. WiFi 2.4G GREEN On The wireless module is ready. (i.e. installed and enabled). Off The wireless module is not ready. (i.e. either not installed or disabled). Blink Data transmitting or receiving over WLAN.
12 WiFi 5G GREEN On The wireless module is ready. (i.e. installed and enabled). Off The wireless module is not ready. (i.e. either not installed or disabled). Blink Data transmitting or receiving over WLAN. DSL GREEN On xDSL Link is established. Off xDSL Link is not established. Blink The xDSL link is training or some traffic is passing through xDSL. INTERNET GREEN On IP connected and no traffic detected. If an IP or PPPoE session is dropped due to an idle timeout, the light will remain green if an ADSL connection is still present. Off Modem power off, modem in bridged mode or ADSL connection not present. In addition, if an IP or PPPoE session is dropped for any reason, other than an idle timeout, the light is turned off. Blink IP connected and IP Traffic is passing thru the device (either direction) RED On Device attempted to become IP connected and failed (no DHCP response, no PPPoE response, PPPoE authentication failed, no IP address from IPCP, etc.)
13 Chapter 3 Web User Interface This section describes how to access the device via the web user interface (WUI) using an Internet browser such as Internet Explorer (version 5.0 and later). 3.1 Default Settings The factory default settings of this device are summarized below. • LAN IP address: 192.168.1.1 • LAN subnet mask: 255.255.255.0 • Administrative access (username: root, password: 12345) • User access (username: user, password: user) • Remote (WAN) access (username: support, password: support) • WLAN access: enabled Technical Note During power on, the device initializes all settings to default values. It will then read the configuration profile from the permanent storage section of flash memory. The default attributes are overwritten when identical attributes with different values are configured. The configuration profile in permanent storage can be created via the web user interface or telnet user interface, or other management protocols. The factory default configuration can be restored either by pushing the reset button for more than ten seconds until the power indicates LED blinking or by clicking the Restore Default Configuration option in the Restore Settings screen.
14 3.2 IP Configuration DHCP MODE When the VR-3060 powers up, the onboard DHCP server will switch on. Basically, the DHCP server issues and reserves IP addresses for LAN devices, such as your PC. To obtain an IP address from the DCHP server, follow the steps provided below. NOTE: The following procedure assumes you are running Windows. However, the general steps involved are similar for most operating systems (OS). Check your OS support documentation for further details. STEP 1: From the Network Connections window, open Local Area Connection (You may also access this screen by double-clicking the Local Area Connection icon on your taskbar). Click the Properties button. STEP 2: Select Internet Protocol (TCP/IP) and click the Properties button. STEP 3: Select Obtain an IP address automatically as shown below. STEP 4: Click OK to submit these settings. If you experience difficulty with DHCP mode, you can try static IP mode instead.
15 STATIC IP MODE In static IP mode, you assign IP settings to your PC manually. Follow these steps to configure your PC IP address to use subnet 192.168.1.x. NOTE: The following procedure assumes you are running Windows. However, the general steps involved are similar for most operating systems (OS). Check your OS support documentation for further details. STEP 1: From the Network Connections window, open Local Area Connection (You may also access this screen by double-clicking the Local Area Connection icon on your taskbar). Click the Properties button. STEP 2: Select Internet Protocol (TCP/IP) and click the Properties button. STEP 3: Change the IP address to the 192.168.1.x (1<x<255) subnet with subnet mask of 255.255.255.0. The screen should now display as shown below. STEP 4: Click OK to submit these settings.
16 3.3 Login Procedure Perform the following steps to login to the web user interface. NOTE: The default settings can be found in section 3.1 Default Settings. STEP 1: Start the Internet browser and enter the default IP address for the device in the Web address field. For example, if the default IP address is 192.168.1.1, type http://192.168.1.1. NOTE: For local administration (i.e. LAN access), the PC running the browser must be attached to the Ethernet, and not necessarily to the device. For remote access (i.e. WAN), use the IP address shown on the Device Information screen and login with remote username and password. STEP 2: A dialog box will appear, such as the one below. Enter the default username and password, as defined in section 3.1 Default Settings. Click OK to continue. NOTE: The login password can be changed later (see section 8.6.1 Accounts).
17 STEP 3: After successfully logging in for the first time, you will reach this screen. You can also reach this page by clicking on the following icon located at the top of the screen.
18 Chapter 4 Device Information You can reach this page by clicking on the following icon located at the top of the screen. The web user interface window is divided into two frames, the main menu (on the left) and the display screen (on the right). The main menu has several options and selecting each of these options opens a submenu with more selections. NOTE: The menu items shown are based upon the configured connection(s) and user account privileges. For example, user account has limited access to configuration modification. Device Info is the first selection on the main menu so it will be discussed first. Subsequent chapters will introduce the other main menu options in sequence. The Device Info Summary screen displays at startup.
19 This screen shows hardware, software, IP settings and other related information.
20 4.1 WAN Select WAN from the Device Info submenu to display the configured PVC(s). Heading Description Interface Name of the interface for WAN Description Name of the WAN connection Type Shows the connection type VlanMuxId Shows 802.1Q VLAN ID IPv6 Shows WAN IPv6 status Igmp Pxy Shows Internet Group Management Protocol (IGMP) proxy status Igmp Src Enbl Shows the status of WAN interface used as IGMP source MLD Pxy Shows Multicast Listener Discovery (MLD) proxy status MLD Src Enbl Shows the status of WAN interface used as MLD source NAT Shows Network Address Translation (NAT) status Firewall Shows the status of Firewall Status Lists the status of DSL link IPv4 Address Shows WAN IPv4 address IPv6 Address Shows WAN IPv6 address
21 4.2 Statistics This selection provides LAN, WAN, ATM and xDSL statistics. NOTE: These screens are updated automatically every 15 seconds. Click Reset Statistics to perform a manual update. 4.2.1 LAN Statistics This screen shows data traffic statistics for each LAN interface. Heading Description Interface LAN interface(s) Received/Transmitted: - Bytes - Pkts - Errs - Drops Number of Bytes Number of Packets Number of packets with errors Number of dropped packets
22 4.2.2 WAN Service This screen shows data traffic statistics for each WAN interface. Heading Description Interface WAN interfaces Description WAN service label Received/Transmitted - Bytes - Pkts - Errs - Drops Number of Bytes Number of Packets Number of packets with errors Number of dropped packets
23 4.2.3 XTM Statistics The following figure shows ATM (Asynchronous Transfer Mode)/PTM (Packet Transfer Mode) statistics. XTM Interface Statistics Heading Description Port Number ATM PORT (0-1) In Octets Number of octets received over the interface Out Octets Number of octets transmitted over the interface In Packets Number of packets received over the interface Out Packets Number of packets transmitted over the interface In OAM Cells Number of OAM Cells received over the interface Out OAM Cells Number of OAM Cells transmitted over the interface In ASM Cells Number of ASM Cells received over the interface Out ASM Cells Number of ASM Cells transmitted over the interface In Packet Errors Number of packets in Error In Cell Errors Number of cells in Error
24 4.2.4 xDSL Statistics The xDSL Statistics screen displays information corresponding to the xDSL type. The two examples below (VDSL & ADSL) show this variation. VDSL
25 ADSL Click the Reset Statistics button to refresh this screen. Field Description Mode VDSL, VDSL2 Traffic Type ATM, PTM Status Lists the status of the DSL link Link Power State Link output power state phyR Status Shows the status of PhyR™ (Physical Layer Re-Transmission) impulse noise protection
26 Field Description Line Coding (Trellis) Trellis On/Off SNR Margin (0.1 dB) Signal to Noise Ratio (SNR) margin Attenuation (0.1 dB) Estimate of average loop attenuation in the downstream direction Output Power (0.1 dBm) Total upstream output power Attainable Rate (Kbps) The sync rate you would obtain Rate (Kbps) Current sync rates downstream/upstream In VDSL mode, the following section is inserted. MSGc Number of bytes in overhead channel message B Number of bytes in Mux Data Frame M Number of Mux Data Frames in a RS codeword T Number of Mux Data Frames in an OH sub-frame R Number of redundancy bytes in the RS codeword S Number of data symbols the RS codeword spans L Number of bits transmitted in each data symbol D The interleaver depth I The interleaver block size in bytes N RS codeword size Delay The delay in milliseconds (msec) INP DMT symbol Super Frames Total number of super frames Super Frame Errors Number of super frames received with errors RS Words Total number of Reed-Solomon code errors RS Correctable Errors Total Number of RS with correctable errors RS Uncorrectable Errors Total Number of RS words with uncorrectable errors OH Frames Total number of OH frames OH Frame Errors Number of OH frames received with errors RS Words Total number of Reed-Solomon code errors RS Correctable Errors Total Number of RS with correctable errors RS Uncorrectable Errors Total Number of RS words with uncorrectable errors HEC Errors Total Number of Header Error Checksum errors OCD Errors Total Number of Out-of-Cell Delineation errors LCD Errors Total number of Loss of Cell Delineation Total Cells Total number of ATM cells (including idle + data cells) Data Cells Total number of ATM data cells Bit Errors Total number of bit errors
27 Total ES Total Number of Errored Seconds Total SES Total Number of Severely Errored Seconds Total UAS Total Number of Unavailable Seconds xDSL BER TEST Click xDSL BER Test on the xDSL Statistics screen to test the Bit Error Rate (BER). A small pop-up window will open after the button is pressed, as shown below. Click Start to start the test or click Close to cancel the test. After the BER testing is complete, the pop-up window will display as follows.
28 xDSL TONE GRAPH Click Draw Graph on the xDSL Statistics screen and a pop-up window will display the xDSL statistics graph, including SNR, Bits per tone, QLN and Hlog of the xDSL line connection, as shown below.
29 4.3 Route Choose Route to display the routes that the VR-3060 has found. Field Description Destination Destination network or destination host Gateway Next hop IP address Subnet Mask Subnet Mask of Destination Flag U: route is up !: reject route G: use gateway H: target is a host R: reinstate route for dynamic routing D: dynamically installed by daemon or redirect M: modified from routing daemon or redirect Metric The 'distance' to the target (usually counted in hops). It is not used by recent kernels, but may be needed by routing daemons. Service Shows the WAN connection label Interface Shows connection interfaces
30 4.4 ARP Click ARP to display the ARP information. Field Description IP address Shows IP address of host PC Flags Complete, Incomplete, Permanent, or Publish HW Address Shows the MAC address of host PC Device Shows the connection interface 4.5 DHCP Click DHCP to display all DHCP Leases. Field Description Hostname Shows the device/host/PC network name MAC Address Shows the Ethernet MAC address of the device/host/PC IP Address Shows IP address of device/host/PC Expires In Shows how much time is left for each DHCP Lease
31 Field Description IPv6 Address Shows IP address of device/host/PC MAC Address Shows the Ethernet MAC address of the device/host/PC Duration Shows leased time in hours Expires In Shows how much time is left for each DHCP Lease
32 4.6 NAT Session This page displays all NAT connection session including both UPD/TCP protocols passing through the device. Click the “Show All” button to display the following. Field Description Source IP The source IP from which the NAT session is established Source Port The source port from which the NAT session is established Destination IP The IP which the NAT session was connected to Destination Port The port which the NAT session was connected to Protocol The Protocol used in establishing the particular NAT session Timeout The time remaining for the TCP/UDP connection to be active
33 4.7 IGMP Info Click IGMP Info to display the list of IGMP entries broadcasting through IGMP proxy enabled wan connection. Field Description Interface The Source interface from which the IGMP report was received WAN The WAN interface from which the multicast traffic is received Groups The destination IGMP group address Member The Source IP from which the IGMP report was received Timeout The time remaining before the IGMP report expires
34 4.8 IPv6 4.8.1 IPv6 Info Click IPv6 Info to display the IPv6 WAN connection info. Field Description Interface WAN interface with IPv6 enabled Status Connection status of the WAN interface Address IPv6 Address of the WAN interface Prefix Prefix received/configured on the WAN interface Device Link-local Address The CPE's LAN Address Default IPv6 Gateway The default WAN IPv6 gateway IPv6 DNS Server The IPv6 DNS servers received from the WAN interface / configured manually
35 4.8.2 IPv6 Neighbor Click IPv6 Neighbor to display the list of IPv6 nodes discovered. Field Description IPv6 Address Ipv6 address of the device(s) found Flags Status of the neighbor device HW Address MAC address of the neighbor device Device Interface from which the device is located
36 4.8.3 IPv6 Route Click IPv6 Route to display the IPv6 route info. Field Description Destination Destination IP Address Gateway Gateway address used for destination IP Metric Metric specified for gateway Interface Interface used for destination IP
37 4.9 CPU & Memory Displays the system performance graphs. Shows the current loading of the CPU and memory usage with dynamic updates. Note: This graph is unavailable for Internet Explorer users.
38 4.10 Network Map The network map is a graphical representation of router’s wan status and LAN devices. Note: This graph is unavailable for Internet Explorer users. 4.11 Wireless 4.11.1 Station Info This page shows authenticated wireless stations and their status. Click the Refresh button to update the list of stations in the WLAN.
39 Consult the table below for descriptions of each column heading. Field Description MAC Lists the MAC address of all the stations. Associated Lists all the stations that are associated with the Access Point, along with the amount of time since packets were transferred to and from each station. If a station is idle for too long, it is removed from this list. Authorized Lists those devices with authorized access. SSID Lists which SSID of the modem that the stations connect to. Interface Lists which interface of the modem that the stations connect to.
40 4.11.2 Site Survey The graph displays wireless APs found in your neighborhood by channel. 5GHz
41 2.4GHz
42 Chapter 5 Basic Setup You can reach this page by clicking on the following icon located at the top of the screen. This will bring you to the following screen.
43 5.1 Wan Setup Add or remove ATM, PTM and ETH WAN interface connections here. Click Add to create a new Layer 2 Interface (see Appendix F - Connection Setup). NOTE: Up to 8 ATM interfaces can be created and saved in flash memory. To remove a connection, click the Remove button.
44 5.1.1 WAN Service Setup This screen allows for the configuration of WAN interfaces. Click the Add button to create a new connection. For connections on ATM or PTM or ETH WAN interfaces see Appendix F - Connection Setup. To remove a connection, select its Remove column radio button and click Remove. Heading Description Interface Name of the interface for WAN Description Name of the WAN connection Type Shows the connection type Vlan8021p VLAN ID is used for VLAN Tagging (IEEE 802.1Q) VlanMuxId Shows 802.1Q VLAN ID VlanTpid VLAN Tag Protocol Identifier IGMP Proxy Shows Internet Group Management Protocol (IGMP) Proxy status IGMP Source Shows the status of WAN interface used as IGMP source NAT Shows Network Address Translation (NAT) status Firewall Shows the Security status IPv6 Shows the WAN IPv6 address MLD Proxy Shows Multicast Listener Discovery (MLD) Proxy status Mld Source Shows the status of WAN interface used as MLD source Remove Select interfaces to remove Edit Click the Edit button to make changes to the WAN interface. To remove a connection, select its Remove column radio button and click Remove. NOTE: Up to 16 PVC profiles can be configured and saved in flash memory.
45 5.2 NAT For NAT features under this section to work, NAT must be enabled in at least one PVC. 5.2.1 Virtual Servers Virtual Servers allow you to direct incoming traffic from the WAN side (identified by Protocol and External port) to the internal server with private IP addresses on the LAN side. The Internal port is required only if the external port needs to be converted to a different port number used by the server on the LAN side. A maximum of 32 entries can be configured. To add a Virtual Server, click Add. The following will be displayed. Click Apply/Save to apply and save the settings.
46 Consult the table below for field and header descriptions. Field/Header Description Choose All InterfaceVirtual server rules will be created for all WAN interfaces. Choose One Interface Use Interface Select a WAN interface from the drop-down menu. Select a Service Or Custom Service User should select the service from the list. Or User can enter the name of their choice. Server IP Address Enter the IP address for the server. Enable NAT Loopback Allows local machines to access virtual server via WAN IP Address External Port Start Enter the starting external port number (when you select Custom Server). When a service is selected, the port ranges are automatically configured. External Port End Enter the ending external port number (when you select Custom Server). When a service is selected, the port ranges are automatically configured. Protocol TCP, TCP/UDP, or UDP. Internal Port Start Enter the internal port starting number (when you select Custom Server). When a service is selected the port ranges are automatically configured Internal Port End Enter the internal port ending number (when you select Custom Server). When a service is selected, the port ranges are automatically configured.
47 5.2.2 Port Triggering Some applications require that specific ports in the firewall be opened for access by the remote parties. Port Triggers dynamically 'Open Ports' in the firewall when an application on the LAN initiates a TCP/UDP connection to a remote party using the 'Triggering Ports'. The Router allows the remote party from the WAN side to establish new connections back to the application on the LAN side using the 'Open Ports'. A maximum 32 entries can be configured. To add a Trigger Port, click Add. The following will be displayed. Click Save/Apply to save and apply the settings. Consult the table below for field and header descriptions.
48 Field/Header Description Use Interface Select a WAN interface from the drop-down menu. Select an Application Or Custom Application User should select the application from the list. Or User can enter the name of their choice. Trigger Port Start Enter the starting trigger port number (when you select custom application). When an application is selected, the port ranges are automatically configured. Trigger Port End Enter the ending trigger port number (when you select custom application). When an application is selected, the port ranges are automatically configured. Trigger Protocol TCP, TCP/UDP, or UDP. Open Port Start Enter the starting open port number (when you select custom application). When an application is selected, the port ranges are automatically configured. Open Port End Enter the ending open port number (when you select custom application). When an application is selected, the port ranges are automatically configured. Open Protocol TCP, TCP/UDP, or UDP.
49 5.2.3 DMZ Host The DSL router will forward IP packets from the WAN that do not belong to any of the applications configured in the Virtual Servers table to the DMZ host computer. To Activate the DMZ host, enter the DMZ host IP address and click Save/Apply. To Deactivate the DMZ host, clear the IP address field and click Save/Apply. Enable NAT Loopback allows PC on the LAN side to access servers in the LAN network via the router’s WAN IP.
50 5.2.4 IP Address Map Mapping Local IP (LAN IP) to some specified Public IP (WAN IP). Field/Header Description Rule The number of the rule Type Mapping type from local to public Local Start IP The beginning of the local IP Local End IP The ending of the local IP Public Start IP The beginning of the public IP Public End IP The ending of the public IP Remove Remove this rule Click the Add button to display the following. Select a Service, then click the Save/Apply button. One to One: mapping one local IP to a specific public IP Many to one: mapping a range of local IP to a specific public IP Many to many(Overload): mapping a range of local IP to a different range of public IP Many to many(No Overload): mapping a range of local IP to a same range of public IP
51 5.2.5 ALG/Pass-Through Support ALG Pass-through for the listed protocols. To allow/deny the corresponding ALG protocol, select Enable / Disable and then click the Save button. After reboot, the protocol will be added/removed from the system module.
52 5.3 LAN Configure the LAN interface settings and then click Apply/Save. Consult the field descriptions below for more details. GroupName: Select an Interface Group. 1st LAN INTERFACE IP Address: Enter the IP address for the LAN port. Subnet Mask: Enter the subnet mask for the LAN port.
53 Enable IGMP Snooping: Standard Mode: In standard mode, multicast traffic will flood to all bridge ports when no client subscribes to a multicast group even if IGMP snooping is enabled. Blocking Mode: In blocking mode, the multicast data traffic will be blocked and not flood to all bridge ports when there are no client subscriptions to any multicast group. Enable IGMP LAN to LAN Multicast: Select Enable from the drop-down menu to allow IGMP LAN to LAN Multicast forwarding Enable Enhanced IGMP: Enable by ticking the checkbox . IGMP packets between LAN ports will be blocked. Enable LAN side firewall: Enable by ticking the checkbox . DHCP Server: To enable DHCP, select Enable DHCP server and enter Start and End IP addresses and the Leased Time. This setting configures the router to automatically assign IP, default gateway and DNS server addresses to every PC on your LAN. Setting TFTP Server: Enable by ticking the checkbox . Then, input the TFTP server address or an IP address. Static IP Lease List: A maximum of 32 entries can be configured. To add an entry, enter MAC address and Static IP address and then click Apply/Save. To remove an entry, tick the corresponding checkbox  in the Remove column and then click the Remove Entries button, as shown below.
54 Select Enable DHCP Server Relay (not available if NAT enabled), and enter the DHCP Server IP Address. This allows the Router to relay the DHCP packets to the remote DHCP server. The remote DHCP server will provide the IP address. 2ND LAN INTERFACE To configure a secondary IP address, tick the checkbox  outlined (in RED) below. IP Address: Enter the secondary IP address for the LAN port. Subnet Mask: Enter the secondary subnet mask for the LAN port. Ethernet Media Type: Configure auto negotiation, or enforce selected speed and duplex mode for the Ethernet ports.
55 5.3.1 LAN IPv6 Autoconfig Configure the LAN interface settings and then click Save/Apply. Consult the field descriptions below for more details.
56 LAN IPv6 Link-Local Address Configuration Heading Description EUI-64 Use EUI-64 algorithm to calculate link-local address from MAC address User Setting Use the Interface Identifier field to define a link-local address Static LAN IPv6 Address Configuration Heading Description Interface Address (prefix length is required): Configure static LAN IPv6 address and subnet prefix length IPv6 LAN Applications Heading Description Stateless Use stateless configuration Refresh Time (sec): The information refresh time option specifies how long a client should wait before refreshing information retrieved from DHCPv6 Stateful Use stateful configuration Start interface ID: Start of interface ID to be assigned to dhcpv6 client End interface ID: End of interface ID to be assigned to dhcpv6 client Leased Time (hour): Lease time for dhcpv6 client to use the assigned IP address Static IP Lease List: A maximum of 32 entries can be configured. To add an entry, enter MAC address and Interface ID and then click Apply/Save.
57 To remove an entry, tick the corresponding checkbox  in the Remove column and then click the Remove Entries button, as shown below. Heading Description Enable RADVD Enable use of router advertisement daemon RA interval Min(sec): Minimum time to send router advertisement RA interval Max(sec): Maximum time to send router advertisement Reachable Time(ms): The time, in milliseconds that a neighbor is reachable after receiving reachability confirmation Default Preference: Preference level associated with the default router MTU (bytes): MTU value used in router advertisement messages to insure that all nodes on a link use the same MTU value Enable Prefix Length Relay Use prefix length receive from WAN interface Enable Configuration Mode Manually configure prefix, prefix length, preferred lifetime and valid lifetime used in router advertisement Enable ULA Prefix Advertisement Allow RADVD to advertise Unique Local Address Prefix Randomly Generate Use a Randomly Generated Prefix Statically Configure Prefix Specify the prefix to be used Preferred Life Time (hour) The preferred life time for this prefix Valid Life Time (hour) The valid life time for this prefix Enable MLD Snooping Enable/disable IPv6 multicast forward to LAN ports Standard Mode Blocking Mode In standard mode, IPv6 multicast traffic will flood to all bridge ports when no client subscribes to a multicast group even if MLD snooping is enabled In blocking mode, IPv6 multicast data traffic will be blocked and not flood to all bridge ports when there are no client subscriptions to any multicast group Enable MLD LAN To LAN Multicast Enable/disable IPv6 multicast between LAN ports
58 5.3.2 Static IP Neighbor This page is used to configure a static IPv4 or IPv6 Neighbor entry. Static ARP entries will be created for these neighbor devices. Click the Add button to display the following. Click Apply/Save to apply and save the settings. Heading Description IP Version The IP version used for the neighbor device IP Address Define the IP Address for the neighbor device MAC Address The MAC Address of the neighbor device Associated Interface The interface where the neighbor device is located
59 5.3.3 UPnP Select the checkbox  provided and click Apply/Save to enable UPnP protocol.
60 5.4 Wireless 5.4.1 Basic 5GHz The Basic option allows you to configure basic features of the wireless LAN interface. Among other things, you can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and configure the channel setting for the wireless LAN interface. Click the Apply/Save button to apply the selected wireless options. Consult the table below for descriptions of these options. Option Description Enable Wireless A checkbox  that enables or disables the wireless LAN interface. When selected, a set of basic wireless options will appear. Enable Wireless Hotspot2.0 Enable Wireless Hotspot 2.0 (Wi-Fi Certified Passpoint) on the wireless interface.
61 Option Description Hide Access Point Select Hide Access Point to protect the access point from detection by wireless active scans. If the access point is hidden, it will not be listed or listed with empty SSID in the scan result of wireless stations. To connect a client to a hidden access point, the station must add the access point manually to its wireless configuration. Clients Isolation When enabled, it prevents client PCs from seeing one another in My Network Places or Network Neighborhood. Also, prevents one wireless client communicating with another wireless client. Disable WMM Advertise Stops the router from ‘advertising’ its Wireless Multimedia (WMM) functionality, which provides basic quality of service for time-sensitive applications (e.g. VoIP, Video). Enable Wireless Multicast Forwarding Select the checkbox  to enable this function. SSID [1-32 characters] Sets the wireless network name. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that user will not be granted access. BSSID The BSSID is a 48-bit identity used to identify a particular BSS (Basic Service Set) within an area. In Infrastructure BSS networks, the BSSID is the MAC (Media Access Control) address of the AP (Access Point); and in Independent BSS or ad hoc networks, the BSSID is generated randomly. Country A drop-down menu that permits worldwide and specific national settings. Local regulations limit channel range: US= worldwide, Japan=1-14, Jordan= 10-13, Israel= 1-13 Country RegRev Wireless country code for transmit power limit. Max Clients The maximum number of clients that can access the router. Wireless - Guest / Virtual Access Points This router supports multiple SSIDs called Guest SSIDs or Virtual Access Points. To enable one or more Guest SSIDs select the checkboxes  in the Enabled column. To hide a Guest SSID, select its checkbox  in the Hidden column. Do the same for Isolate Clients and Disable WMM Advertise. For a description of these two functions, see the previous entries for “Clients Isolation” and “Disable WMM Advertise”. Similarly, for Enable WMF, Max Clients and BSSID, consult the matching entries in this table. NOTE: Remote wireless hosts cannot scan Guest SSIDs.
62 5.4.2 Security 5GHz The following screen appears when Wireless Security is selected. The options shown here allow you to configure security features of the wireless LAN interface. Click Apply/Save to implement new configuration settings. Please see 6.12.3 for WPS setup instructions. WIRELESS SECURITY Setup requires that the user configure these settings using the Web User Interface (see the table below). Select SSID Select the wireless network name from the drop-down menu. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that client will not be granted access. Network Authentication This option specifies whether a network key is used for authentication to the wireless network. If network authentication is set to Open, then no authentication is provided. Despite this, the identity of the client is still verified.
63 Each authentication type has its own settings. For example, selecting 802.1X authentication will reveal the RADIUS Server IP address, Port and Key fields. WEP Encryption will also be enabled as shown below. The settings for WPA2-PSK authentication are shown next. WEP Encryption This option specifies whether data sent over the network is encrypted. The same network key is used for data encryption and network authentication. Four network keys can be defined although only one can be used at any one time. Use the Current Network Key list box to select the appropriate network key. Security options include authentication and encryption services based on the wired equivalent privacy (WEP) algorithm. WEP is a set of security services used to protect 802.11 networks from unauthorized access, such as eavesdropping; in this case, the capture of wireless network traffic. When data encryption is enabled, secret shared encryption keys are generated and used by the source station and the destination station to alter frame bits, thus avoiding disclosure to eavesdroppers.
64 Under shared key authentication, each wireless station is assumed to have received a secret shared key over a secure channel that is independent from the 802.11 wireless network communications channel. Encryption Strength This drop-down list box will display when WEP Encryption is enabled. The key strength is proportional to the number of binary bits comprising the key. This means that keys with a greater number of bits have a greater degree of security and are considerably more difficult to crack. Encryption strength can be set to either 64-bit or 128-bit. A 64-bit key is equivalent to 5 ASCII characters or 10 hexadecimal numbers. A 128-bit key contains 13 ASCII characters or 26 hexadecimal numbers. Each key contains a 24-bit header (an initiation vector) which enables parallel decoding of multiple streams of encrypted data. Please see 6.12 for MAC Filter, Wireless Bridge and Advanced Wireless features.
65 5.4.3 Basic 2.4GHz The Basic option allows you to configure basic features of the wireless LAN interface. Among other things, you can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements. Click the Apply/Save button to apply the selected wireless options. Consult the table below for descriptions of these options. Option Description Enable Wireless A checkbox  that enables or disables the wireless LAN interface. When selected, a set of basic wireless options will appear. Enable Wireless Hotspot2.0 Enable Wireless Hotspot 2.0 (Wi-Fi Certified Passpoint) on the wireless interface.
66 Option Description Hide Access Point Select Hide Access Point to protect the access point from detection by wireless active scans. If the access point is hidden, it will not be listed or listed with empty SSID in the scan result of wireless stations. To connect a client to a hidden access point, the station must add the access point manually to its wireless configuration. Clients Isolation When enabled, it prevents client PCs from seeing one another in My Network Places or Network Neighborhood. Also, prevents one wireless client communicating with another wireless client. Disable WMM Advertise Stops the router from ‘advertising’ its Wireless Multimedia (WMM) functionality, which provides basic quality of service for time-sensitive applications (e.g. VoIP, Video). Enable Wireless Multicast Forwarding Select the checkbox  to enable this function. SSID [1-32 characters] Sets the wireless network name. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that user will not be granted access. BSSID The BSSID is a 48-bit identity used to identify a particular BSS (Basic Service Set) within an area. In Infrastructure BSS networks, the BSSID is the MAC (Media Access Control) address of the AP (Access Point); and in Independent BSS or ad hoc networks, the BSSID is generated randomly. Country A drop-down menu that permits worldwide and specific national settings. Local regulations limit channel range: US= worldwide, Japan=1-14, Jordan= 10-13, Israel= 1-13 Country RegRev Wireless country code for transmit power limit. Max Clients The maximum number of clients that can access the router. Wireless - Guest / Virtual Access Points This router supports multiple SSIDs called Guest SSIDs or Virtual Access Points. To enable one or more Guest SSIDs select the checkboxes  in the Enabled column. To hide a Guest SSID, select its checkbox  in the Hidden column. Do the same for Isolate Clients and Disable WMM Advertise. For a description of these two functions, see the previous entries for “Clients Isolation” and “Disable WMM Advertise”. Similarly, for Enable WMF, Max Clients and BSSID, consult the matching entries in this table. NOTE: Remote wireless hosts cannot scan Guest SSIDs.
67 5.4.4 Security 2.4GHz The following screen appears when Wireless Security is selected. The options shown here allow you to configure security features of the wireless LAN interface. Click Apply/Save to implement new configuration settings. Please see 6.12.9 for WPS setup instructions. WIRELESS SECURITY Setup requires that the user configure these settings using the Web User Interface (see the table below). Select SSID Select the wireless network name from the drop-down menu. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that client will not be granted access. Network Authentication This option specifies whether a network key is used for authentication to the wireless network. If network authentication is set to Open, then no authentication is provided. Despite this, the identity of the client is still verified.
68 Each authentication type has its own settings. For example, selecting 802.1X authentication will reveal the RADIUS Server IP address, Port and Key fields. WEP Encryption will also be enabled as shown below. The settings for WPA2-PSK authentication are shown next. WEP Encryption This option specifies whether data sent over the network is encrypted. The same network key is used for data encryption and network authentication. Four network keys can be defined although only one can be used at any one time. Use the Current Network Key list box to select the appropriate network key. Security options include authentication and encryption services based on the wired equivalent privacy (WEP) algorithm. WEP is a set of security services used to protect 802.11 networks from unauthorized access, such as eavesdropping; in this case, the capture of wireless network traffic. When data encryption is enabled, secret shared encryption keys are generated and used by the source station and the destination station to alter frame bits, thus avoiding disclosure to eavesdroppers.
69 Under shared key authentication, each wireless station is assumed to have received a secret shared key over a secure channel that is independent from the 802.11 wireless network communications channel. Encryption Strength This drop-down list box will display when WEP Encryption is enabled. The key strength is proportional to the number of binary bits comprising the key. This means that keys with a greater number of bits have a greater degree of security and are considerably more difficult to crack. Encryption strength can be set to either 64-bit or 128-bit. A 64-bit key is equivalent to 5 ASCII characters or 10 hexadecimal numbers. A 128-bit key contains 13 ASCII characters or 26 hexadecimal numbers. Each key contains a 24-bit header (an initiation vector) which enables parallel decoding of multiple streams of encrypted data. Please see 6.12 for MAC Filter, Wireless Bridge and Advanced Wireless features.
70 5.5 Parental Control This selection provides WAN access control functionality. 5.5.1 Time Restriction This feature restricts access from a LAN device to an outside network through the device on selected days at certain times. Make sure to activate the Internet Time server synchronization as described in section 8.5 Internet Time, so that the scheduled times match your local time. Clicking on the checkbox in the Enable field allows the user to select all / none entries for Enabling/Disabling. Click Add to display the following screen. See below for field descriptions. Click Apply/Save to add a time restriction. User Name: A user-defined label for this restriction. Browser's MAC Address: MAC address of the PC running the browser. Other MAC Address: MAC address of another LAN device. Days of the Week: The days the restrictions apply. Start Blocking Time: The time the restrictions start. End Blocking Time: The time the restrictions end.
71 5.5.2 URL Filter This screen allows for the creation of a filter rule for access rights to websites based on their URL address and port number. Select URL List Type: Exclude or Include. Tick the Exclude radio button to deny access to the websites listed. Tick the Include radio button to restrict access to only those listed websites. Then click Add to display the following screen. Enter the URL address and port number then click Apply/Save to add the entry to the URL filter. URL Addresses begin with “www”, as shown in this example.
72 A maximum of 100 entries can be added to the URL Filter list.
73 5.6 Home networking 5.6.1 Print Server This page allows you to enable or disable printer support. Please reference Appendix E to see the procedure for enabling the Printer Server. 5.6.2 DLNA Enabling DLNA allows users to share digital media, like pictures, music and video, to other LAN devices from the digital media server. Insert the USB drive into the USB host port on the back of the router. Click Enable on-board digital media server, a dropdown list of directories found on the USB driver will be available for selection. Select media path from the drop-down list or manually modify the media library path and click Apply/Save to enable the DLNA media server.
74 5.6.3 Storage Service Enabling Samba service allows the user to share files on the storage device. Different levels of user access can be configured after samba security mode is enabled. This page also displays storage devices attached to the USB host. Display after storage device attached (for your reference).
75 5.6.4 USB Speed This page allows you to enable / disable USB 3.0 device support. Note: Enabling USB 3.0 can cause interference with the built-in 2.4GHz wireless radio. It is advised leaving the default value as USB 2.0
76 Chapter 6 Advanced Setup You can reach this page by clicking on the following icon located at the top of the screen. 6.1 Auto-detection setup The auto-detection function is used for CPE to detect WAN service for either ETHWAN or xDSL interfaces. The feature is designed for the scenario that requires only one WAN service in different applications. The Auto Detection page simply provides a checkbox allowing users to enable or disable the feature. Check the checkbox to display the following configuration options.
77 Enter the PPP username/password given by your service provider for PPP service detection. Select a LAN-as-WAN Ethernet port for auto-detect: Select the Ethernet Port that will be used as ETH WAN during auto-detection. For models with ETH WAN port, only ETH WAN port is available to be used as WAN port.
78 WAN services list for ATM mode: A maximum of 7 WAN services with corresponding PVC are required to be configured for ADSL ATM mode. The services will be detected in order. Users can modify the 7 pre-configured services and select disable to ignore any of those services to meet their own requirement and also reduce the detection cycle. WAN services list for PTM mode: A maximum of 7 WAN services with corresponding VLAN ID (-1 indicates no VLAN ID is required for the service) are required to be configured for ADSL/VDSL PTM mode and ETHWAN. The services will be detected in order. Users can modify the 7 pre-configured services and select disable to ignore any of the services to meet their own requirements and also reduce the detection cycle.
79 Click "Apply/Save" to activate the auto-detect function. Options for each WAN service: These options are selectable for each WAN service. Users can pre-configure both WAN services and other provided settings to meet their deployed requirements. Auto Detection status and Restart The Auto-detection status is used to display the real time status of the Auto-detection feature. The Restart button is used to detect all the WAN services that are either detected by the auto-detection feature or configured manually by users. The following window will pop up upon clicking the Restart button. Click the OK button to proceed.
80 Auto Detection notice Note: The following description concerning ETHWAN is for multiple LAN port devices only. 1) This feature will automatically detect one WAN service only. If customers require multiple WAN services, manual configuration is required. 2) If a physical ETHWAN port is detected, the Auto Detection for ETHWAN will be fixed on the physical ETHWAN port and cannot be configured for any LAN port; if the physical ETHWAN port is not detected, the Auto Detection for ETHWAN will be configured to the 4th LAN port by default and allows it to be configured for any LAN port as well. 3) For cases in which both the DSL port and ETHWAN port are plugged in at the same time, the DSL WAN will have priority over ETHWAN. For example, the ETHWAN port is plugged in with a WAN service detected automatically and then the DSL port is plugged in and linked up. The Auto Detection feature will clear the WAN service for ETHWAN and re-detect the WAN service for DSL port. 4) If none of the pre-configured services are detected, a Bridge service will be created.
81 6.2 Security For detailed descriptions, with examples, please consult Appendix A - Firewall. 6.2.1 IP Filtering This screen sets filter rules that limit IP traffic (Outgoing/Incoming). Multiple filter rules can be set and each applies at least one limiting condition. For individual IP packets to pass the filter all conditions must be fulfilled. NOTE: This function is not available when in bridge mode. Instead, MAC Filtering performs a similar function. OUTGOING IP FILTER By default, all outgoing IP traffic is allowed, but IP traffic can be blocked with filters. To add a filter (to block some outgoing IP traffic), click the Add button. On the following screen, enter your filter criteria and then click Apply/Save. Consult the table below for field descriptions.
82 Field Description Filter Name The filter rule label. IP Version Select from the drop down menu. Protocol TCP, TCP/UDP, UDP, or ICMP. Source IP address Enter source IP address. Source Port (port or port:port) Enter source port number or range. Destination IP address Enter destination IP address. Destination Port (port or port:port) Enter destination port number or range. INCOMING IP FILTER By default, all incoming IP traffic is blocked, but IP traffic can be allowed with filters. To add a filter (to allow incoming IP traffic), click the Add button. On the following screen, enter your filter criteria and then click Apply/Save. Consult the table below for field descriptions.
83 Field Description Filter Name The filter rule label. IP Version Select from the drop down menu. Protocol TCP, TCP/UDP, UDP, or ICMP. Policy Permit/Drop packets specified by the firewall rule. Source IP address Enter source IP address. Source Port (port or port:port) Enter source port number or range. Destination IP address Enter destination IP address. Destination Port (port or port:port) Enter destination port number or range. At the bottom of this screen, select the WAN and LAN Interfaces to which the filter rule will apply. You may select all or just a subset. WAN interfaces in bridge mode or without firewall enabled are not available.
84 Denial of Service Denial of Services currently provides Syn-flood protection, furtive port scanner protection and Ping of death protection. This web page allows you to activate/de-activate them and to set the maximum average limit (packet per second) and the maximum burst (packet amount) for each protection. Click the Apply/Save button to save and (de)activate the protection.
85 6.2.2 MAC Filtering NOTE: This option is only available in bridge mode. Other modes use IP Filtering to perform a similar function. Each network device has a unique 48-bit MAC address. This can be used to filter (block or forward) packets based on the originating device. MAC filtering policy and rules for the VR-3060 can be set according to the following procedure. The MAC Filtering Global Policy is defined as follows. FORWARDED means that all MAC layer frames will be FORWARDED except those matching the MAC filter rules. BLOCKED means that all MAC layer frames will be BLOCKED except those matching the MAC filter rules. The default MAC Filtering Global policy is FORWARDED. It can be changed by clicking the Change Policy button. Choose Add or Remove to configure MAC filtering rules. The following screen will appear when you click Add. Create a filter to identify the MAC layer frames by specifying at least one condition below. If multiple conditions are specified, all of them must be met.
86 Click Save/Apply to save and activate the filter rule. Consult the table below for detailed field descriptions. Field Description Protocol Type PPPoE, IPv4, IPv6, AppleTalk, IPX, NetBEUI, IGMP Destination MAC Address Defines the destination MAC address Source MAC Address Defines the source MAC address Frame Direction Select the incoming/outgoing packet interface WAN Interfaces Applies the filter to the selected bridge interface
87 6.3 Quality of Service (QoS) NOTE: QoS must be enabled in at least one PVC to display this option. (See Appendix F - Connection Setup for detailed PVC setup instructions). To Enable QoS tick the checkbox and select a Default DSCP Mark. Click Apply/Save to activate QoS. QoS and DSCP Mark are defined as follows: Quality of Service (QoS): This provides different priority to different users or data flows, or guarantees a certain level of performance to a data flow in accordance with requests from Queue Prioritization. Default Differentiated Services Code Point (DSCP) Mark: This specifies the per hop behavior for a given flow of packets in the Internet Protocol (IP) header that do not match any other QoS rule.
88 6.3.1 QoS Queue 6.3.1.1 QoS Queue Configuration Configure queues with different priorities to be used for QoS setup. In ATM mode, a maximum of 16 queues can be configured. In PTM mode, a maximum of 8 queues can be configured. For each Ethernet interface, a maximum of 8 queues can be configured. For each Ethernet interface, a maximum of 8 queues can be configured. (Please see the screen on the following page).
89
90 To remove queues, check their remove-checkboxes (for user created queues), then click the Remove button. The Enable button will scan through every queue in the table. Queues with the enable-checkbox checked will be enabled. Queues with the enable-checkbox un-checked will be disabled. The enable-checkbox also shows status of the queue after page reload. Note that if WMM function is disabled in the Wireless Page, queues related to wireless will not take effect. This function follows the Differentiated Services rule of IP QoS. You can create a new Queue entry by clicking the Add button. Enable and assign an interface and precedence on the next screen. Click Save/Reboot on this screen to activate it. Click Add to display the following screen. Name: Identifier for this Queue entry. Enable: Enable/Disable the Queue entry. Interface: Assign the entry to a specific network interface (QoS enabled). After selecting an Interface the following will be displayed.
91 The precedence list shows the scheduler algorithm for each precedence level. Queues of equal precedence will be scheduled based on the algorithm. Queues of unequal precedence will be scheduled based on SP. Shaping Rate: Specify a shaping rate limit to the defined queue. Click Apply/Save to apply and save the settings.
92 6.3.1.2 Wlan Queue Displays the list of available wireless queues for WMM and wireless data transmit priority.
93 6.3.2 QoS Classification The network traffic classes are listed in the following table. Click Add to configure a network traffic class rule and Enable to activate it. To delete an entry from the list, click Remove. This screen creates a traffic class rule to classify the upstream traffic, assign queuing priority and optionally overwrite the IP header DSCP byte. A rule consists of a class name and at least one logical condition. All the conditions specified in the rule must be satisfied for it to take effect. Click Apply/Save to save and activate the rule.
94 Field Description Traffic Class Name Enter a name for the traffic class. Rule Order Last is the only option. Rule Status Disable or enable the rule. Classification Criteria Ingress Interface Select an interface: (i.e. LAN, WAN, local, ETH1, ETH2, ETH3, wl0) Ether Type Set the Ethernet type (e.g. IP, ARP, IPv6). Source MAC Address A packet belongs to SET-1, if a binary-AND of its source MAC address with the Source MAC Mask is equal to the binary-AND of the Source MAC Mask and this field. Source MAC Mask This is the mask used to decide how many bits are checked in Source MAC Address. Destination MAC Address A packet belongs to SET-1 then the result that the Destination MAC Address of its header binary-AND to the Destination MAC Mask must equal to the result that this field binary-AND to the Destination MAC Mask. Destination MAC Mask This is the mask used to decide how many bits are checked in the Destination MAC Address. Classification Results Specify Egress Interface Choose the egress interface from the available list. Specify Egress Queue Choose the egress queue from the list of available for the specified egress interface. Mark Differentiated Service Code Point The selected Code Point gives the corresponding priority to packets that satisfy the rule. Mark 802.1p Priority Select between 0-7. - Class non-vlan packets egress to a non-vlan interface will be tagged with VID 0 and the class rule p-bits. - Class vlan packets egress to a non-vlan interface will have the packet p-bits re-marked by the class rule p-bits. No additional vlan tag is added. - Class non-vlan packets egress to a vlan interface will be tagged with the interface VID and the class rule p-bits. - Class vlan packets egress to a vlan interface will be additionally tagged with the packet VID, and the class rule p-bits. Set Rate Limit The data transmission rate limit in kbps.
95 6.3.3 QoS Port Shaping QoS port shaping supports traffic shaping of the Ethernet interface.Input the shaping rate and burst size to enforce QoS rule on each interface. If "Shaping Rate" is set to "-1", it means no shaping and "Burst Size" will be ignored. Click Apply/Save to apply and save the settings.
96 6.4 Routing The following routing functions are accessed from this menu: Default Gateway, Static Route, Policy Routing and RIP. NOTE: In bridge mode, the RIP menu option is hidden while the other menu options are shown but ineffective. 6.4.1 Default Gateway The default gateway interface list can have multiple WAN interfaces served as system default gateways but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected. Priority order can be changed by removing all and adding them back in again. Click Apply/Save to apply and save the settings.
97 6.4.2 Static Route This option allows for the configuration of static routes by destination IP. Click Add to create a static route or click Remove to delete a static route. After clicking Add the following will display. IP Version: Select the IP version to be IPv4 or IPv6. Destination IP address/prefix length: Enter the destination IP address. Interface: Select the proper interface for the rule. Gateway IP Address: The next-hop IP address. Metric: The metric value of routing. After completing the settings, click Apply/Save to add the entry to the routing table.
98 6.4.3 Policy Routing This option allows for the configuration of static routes by policy. Click Add to create a routing policy or Remove to delete one. On the following screen, complete the form and click Apply/Save to create a policy. Field Description Policy Name Name of the route policy Physical LAN Port Specify the port to use this route policy Source IP IP Address to be routed Use Interface Interface that traffic will be directed to Default Gateway IP IP Address of the default gateway
99 6.4.4 RIP To activate RIP, configure the RIP version/operation mode and select the Enabled checkbox  for at least one WAN interface before clicking Save/Apply.
100 6.5 DNS 6.5.1 DNS Server Select DNS Server Interface from available WAN interfaces OR enter static DNS server IP addresses for the system. In ATM mode, if only a single PVC with IPoA or static IPoE protocol is configured, Static DNS server IP addresses must be entered. DNS Server Interfaces can have multiple WAN interfaces served as system DNS servers but only one will be used according to the priority with the first being the highest and the last one the lowest priority if the WAN interface is connected. Priority order can be changed by removing all and adding them back in again. Click Apply/Save to save the new configuration.
101 6.5.2 Dynamic DNS The Dynamic DNS service allows you to map a dynamic IP address to a static hostname in any of many domains, allowing the VR-3060 to be more easily accessed from various locations on the Internet. To add a dynamic DNS service, click Add. The following screen will display. Click Apply/Save to save your settings. Consult the table below for field descriptions. Field Description D-DNS provider Select a dynamic DNS provider from the list Hostname Enter the name of the dynamic DNS server Interface Select the interface from the list Username Enter the username of the dynamic DNS server Password Enter the password of the dynamic DNS server
102 6.5.3 DNS Entries The DNS Entry page allows you to add domain name and IP address pairs desired to be resolved by the DSL router. Choose Add or Remove to configure a DNS Entry. The entries will become active after save/reboot. Enter the domain name and IP address that needs to be resolved locally, and click the Add Entry button.
103 6.5.4 DNS Proxy/Relay DNS proxy receives DNS queries and forwards DNS queries to the Internet. After the CPE gets answers from the DNS server, it replies to the LAN clients. Configure DNS proxy with the default setting, when the PC gets an IP via DHCP, the domain name, Home, will be added to PC’s DNS Suffix Search List, and the PC can access route with “Comtrend.Home”. Click Apply/Save to apply and save the settings.
104 6.6 DSL The DSL Settings screen allows for the selection of DSL modulation modes. For optimum performance, the modes selected should match those of your ISP. DSL Mode Data Transmission Rate - Mbps (Megabits per second) G.Dmt Downstream: 12 Mbps Upstream: 1.3 Mbps G.lite Downstream: 4 Mbps Upstream: 0.5 Mbps T1.413 Downstream: 8 Mbps Upstream: 1.0 Mbps ADSL2 Downstream: 12 Mbps Upstream: 1.0 Mbps AnnexL Supports longer loops but with reduced transmission rates ADSL2+ Downstream: 24 Mbps Upstream: 1.0 Mbps AnnexM Downstream: 24 Mbps Upstream: 3.5 Mbps VDSL2 Downstream: 100 Mbps Upstream: 60 Mbps
105 VDSL Profile Maximum Downstream Throughput- Mbps (Megabits per second) 8a Downstream 50 8b Downstream 50 8c Downstream: 50 8d Downstream: 50 12a Downstream: 68 12b Downstream: 68 17a Downstream: 100 30a Downstream: 100 Mbps Upstream: 100 Mbps Options Description US0 Band between 20 and 138 kHz for long loops to upstream Bitswap Enable Enables adaptive handshaking functionality SRA Enable Enables Seamless Rate Adaptation (SRA) G997.1 EOC xTU-R Serial Number Select Equipment Serial Number or Equipment MAC Address to use router’s serial number or MAC address in ADSL EOC messages
106 6.7 Interface Grouping Interface Grouping supports multiple ports to PVC and bridging groups. Each group performs as an independent network. To use this feature, you must create mapping groups with appropriate LAN and WAN interfaces using the Add button. The Remove button removes mapping groups, returning the ungrouped interfaces to the Default group. Only the default group has an IP interface. To add an Interface Group, click the Add button. The following screen will appear. It lists the available and grouped interfaces. Follow the instructions shown onscreen.
107 Automatically Add Clients With Following DHCP Vendor IDs: Add support to automatically map LAN interfaces to PVC's using DHCP vendor ID (option 60). The local DHCP server will decline and send the requests to a remote DHCP server by mapping the appropriate LAN interface. This will be turned on when Interface Grouping is enabled. For example, imagine there are 4 PVCs (0/33, 0/36, 0/37, 0/38). VPI/VCI=0/33 is for PPPoE while the other PVCs are for IP set-top box (video). The LAN interfaces are ETH1, ETH2, ETH3, and ETH4.
108 The Interface Grouping configuration will be: 1. Default: ETH1, ETH2, ETH3, and ETH4. 2. Video: nas_0_36, nas_0_37, and nas_0_38. The DHCP vendor ID is "Video". If the onboard DHCP server is running on "Default" and the remote DHCP server is running on PVC 0/36 (i.e. for set-top box use only). LAN side clients can get IP addresses from the CPE's DHCP server and access the Internet via PPPoE (0/33). If a set-top box is connected to ETH1 and sends a DHCP request with vendor ID "Video", the local DHCP server will forward this request to the remote DHCP server. The Interface Grouping configuration will automatically change to the following: 1. Default: ETH2, ETH3, and ETH4 2. Video: nas_0_36, nas_0_37, nas_0_38, and ETH1.
109 6.8 IP Tunnel 6.8.1 IPv6inIPv4 Configure 6in4 tunneling to encapsulate IPv6 traffic over explicitly-configured IPv4 links. Click the Add button to display the following. Click Apply/Save to apply and save the settings. Options Description Tunnel Name Input a name for the tunnelMechanism Mechanism used by the tunnel deployment Associated WAN Interface Select the WAN interface to be used by the tunnelAssociated LAN Interface Select the LAN interface to be included in the tunnelManual/Automatic Select automatic for point-to-multipoint tunneling / manual for point-to-point tunneling IPv4 Mask Length The subnet mask length used for the IPv4 interface6rd Prefix with Prefix Length Prefix and prefix length used for the IPv6 interfaceBorder Relay IPv4 Address Input the IPv4 address of the other device
110 6.8.2 IPv4inIPv6 Configure 4in6 tunneling to encapsulate IPv4 traffic over an IPv6-only environment. Click the Add button to display the following. Click Apply/Save to apply and save the settings. Options Description Tunnel Name Input a name for the tunnelMechanism Mechanism used by the tunnel deployment Associated WAN Interface Select the WAN interface to be used by the tunnelAssociated LAN Interface Select the LAN interface to be included in the tunnelManual/Automatic Select automatic for point-to-multipoint tunneling / manual for point-to-point tunneling AFTR Address of Address Family Translation Router
111 6.9 Certificate A certificate is a public key, attached with its owner’s information (company name, server name, personal real name, contact e-mail, postal address, etc) and digital signatures. There will be one or more digital signatures attached to the certificate, indicating that these entities have verified that this certificate is valid. 6.9.1 Local CREATE CERTIFICATE REQUEST Click Create Certificate Request to generate a certificate-signing request. The certificate-signing request can be submitted to the vendor/ISP/ITSP to apply for a certificate. Some information must be included in the certificate-signing request. Your vendor/ISP/ITSP will ask you to provide the information they require and to provide the information in the format they regulate. Enter the required information and click Apply to generate a private key and a certificate-signing request. The following table is provided for your reference.
112 Field Description Certificate Name A user-defined name for the certificate. Common Name Usually, the fully qualified domain name for the machine. Organization Name The exact legal name of your organization. Do not abbreviate. State/Province Name The state or province where your organization is located. It cannot be abbreviated. Country/Region Name The two-letter ISO abbreviation for your country. IMPORT CERTIFICATE Click Import Certificate to paste the certificate content and the private key provided by your vendor/ISP/ITSP into the corresponding boxes shown below. Enter a certificate name and click the Apply button to import the certificate and its private key.
113 6.9.2 Trusted CA CA is an abbreviation for Certificate Authority, which is a part of the X.509 system. It is itself a certificate, attached with the owner information of this certificate authority; but its purpose is not encryption/decryption. Its purpose is to sign and issue certificates, in order to prove that these certificates are valid. Click Import Certificate to paste the certificate content of your trusted CA. The CA certificate content will be provided by your vendor/ISP/ITSP and is used to authenticate the Auto-Configuration Server (ACS) that the CPE will connect to. Enter a certificate name and click Apply to import the CA certificate.
114 6.10 Power Management This screen allows for control of hardware modules to evaluate power consumption. Use the buttons to select the desired option, click Apply and check the response.
115 6.11 Multicast Input new IGMP or MLD protocol configuration fields if you want modify default values shown. Then click Apply/Save. Multicast Precedence: Select precedence of multicast packets. Multicast Strict Grouping Enforcement: Enable/Disable multicast strict grouping. Field Description Default Version Define IGMP using version with video server.
116 Field Description Query Interval The query interval is the amount of time in seconds between IGMP General Query messages sent by the router (if the router is the querier on this subnet). The default query interval is 125 seconds. Query Response Interval The query response interval is the maximum amount of time in seconds that the IGMP router waits to receive a response to a General Query message. The query response interval is the Maximum Response Time field in the IGMP v2 Host Membership Query message header. The default query response interval is 10 seconds and must be less than the query interval. Last Member Query Interval The last member query interval is the amount of time in seconds that the IGMP router waits to receive a response to a Group-Specific Query message. The last member query interval is also the amount of time in seconds between successive Group-Specific Query messages. The default last member query interval is 10 seconds. Robustness Value The robustness variable is a way of indicating how susceptible the subnet is to lost packets. IGMP can recover from robustness variable minus 1 lost IGMP packets. The robustness variable should be set to a value of 2 or greater. The default robustness variable value is 2. Maximum Multicast Groups Setting the maximum number of Multicast groups. Maximum Multicast Data Sources (for IGMPv3) Define the maximum multicast video stream number. Maximum Multicast Group Members Setting the maximum number of groups that ports can accept. Fast Leave Enable When you enable IGMP fast-leave processing, the switch immediately removes a port when it detects an IGMP version 2 leave message on that port.
117 6.12 Wireless 6.12.1 Basic 5GHz The Basic option allows you to configure basic features of the wireless LAN interface. Among other things, you can enable or disable the wireless LAN interface, hide the network from active scans, set the wireless network name (also known as SSID) and restrict the channel set based on country requirements. Click Apply/Save to configure the basic wireless options. Consult the table below for descriptions of these options.
118 Option Description Enable Wireless A checkbox  that enables or disables the wireless LAN interface. When selected, a set of basic wireless options will appear. Enable Wireless Hotspot2.0 Enable Wireless Hotspot 2.0 (Wi-Fi Certified Passpoint) on the wireless interface. Hide Access Point Select Hide Access Point to protect the access point from detection by wireless active scans. If the access point is hidden, it will not be listed or listed with empty SSID in the scan result of wireless stations. To connect a client to a hidden access point, the station must add the access point manually to its wireless configuration. Clients Isolation When enabled, it prevents client PCs from seeing one another in My Network Places or Network Neighborhood. Also, prevents one wireless client communicating with another wireless client. Disable WMM Advertise Stops the router from ‘advertising’ its Wireless Multimedia (WMM) functionality, which provides basic quality of service for time-sensitive applications (e.g. VoIP, Video). Enable Wireless Multicast Forwarding Select the checkbox  to enable this function. SSID [1-32 characters] Sets the wireless network name. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that user will not be granted access. BSSID The BSSID is a 48-bit identity used to identify a particular BSS (Basic Service Set) within an area. In Infrastructure BSS networks, the BSSID is the MAC (Media Access Control) address of the AP (Access Point); and in Independent BSS or ad hoc networks, the BSSID is generated randomly. Country A drop-down menu that permits worldwide and specific national settings. Local regulations limit channel range: US= worldwide, Japan=1-14, Jordan= 10-13, Israel= 1-13 Country RegRev Wireless country code for transmit power limit. Max Clients The maximum number of clients that can access the router. Wireless - Guest / Virtual Access Points This router supports multiple SSIDs called Guest SSIDs or Virtual Access Points. To enable one or more Guest SSIDs select the checkboxes  in the Enabled column. To hide a Guest SSID select its checkbox  in the Hidden column. Do the same for Isolate Clients and Disable WMM Advertise. For a description of these two functions, see the previous entries for “Clients Isolation” and “Disable WMM Advertise”. Similarly, for Enable WMF, Max Clients and BSSID, consult the matching entries in this table. NOTE: Remote wireless hosts cannot scan Guest SSIDs.
119 6.12.2 Security 5GHz The following screen appears when Wireless Security is selected. The options shown here allow you to configure security features of the wireless LAN interface. Please see 6.12.3 for WPS setup instructions. Click Apply/Save to implement new configuration settings. WIRELESS SECURITY Setup requires that the user configure these settings using the Web User Interface (see the table below). Select SSID Select the wireless network name from the drop-down menu. SSID stands for Service Set Identifier. All stations must be configured with the correct SSID to access the WLAN. If the SSID does not match, that client will not be granted access. Network Authentication This option specifies whether a network key is used for authentication to the wireless network. If network authentication is set to Open, then no authentication is provided. Despite this, the identity of the client is still verified. Each authentication type has its own settings. For example, selecting 802.1X authentication will reveal the RADIUS Server IP address, Port and Key fields. WEP Encryption will also be enabled as shown below.
120 Different authentication type pops up different settings requests. Choosing 802.1X, enter RADIUS Server IP address, RADIUS Port, RADIUS key and Current Network Key. Also, enable WEP Encryption and select Encryption Strength. Select the Current Network Key and enter 13 ASCII characters or 26 hexadecimal digits for 128-bit encryption keys and enter 5 ASCII characters or 10 hexadecimal digits for 64-bit encryption keys. Choosing WPA2-PSK, you must enter WPA Pre-Shared Key and Group Rekey Interval. WEP Encryption This option specifies whether data sent over the network is encrypted. The same network key is used for data encryption and network authentication. Four network keys can be defined although only one can be used at any one time. Use the Current Network Key list box to select the appropriate network key.

Navigation menu