Cooper Wiring Devices RF9642Z Z-Wave Plus Accessory Dimmer User Manual

Cooper Wiring Devices Inc Z-Wave Plus Accessory Dimmer

User Manual

ACCESSORYACCESSORYACCESSORYWhiteWhiteMaster Control AccessoryDisconnect SwitchRedBlack BlackGreen GreenSwitch IdentificationDisconnect SwitchPull out to change bulbs (Master Dimmer only)Press to DIMLight level may be adjusted with lightsON or OFFPress to BRIGHTENON/OFF ButtonLight level indicators (blue)LED ON/OFF indicator (amber) HotNeutral120VGreenGroundWhite WhiteWhiteBlackACCESSORYDIMMERLight FixtureBlack RedNeutral120VGreenGroundWhiteWhiteMASTERDIMMERNeutralHotSingle Location Control Installation (requires one Master dimmer)Identify existing wiring (This switch will be a single-pole) and tag “Hot” wire. Use voltage tester as necessary to confirm “Hot” wire (Voltage will be present at the “Hot” wire when the lights are off).Disconnect existing switch and remove. Connect master dimmer as shown by connecting black wire of dimmer to tagged “Hot” wire. Red wire must be connected to the wire that goes to the light.Gently push dimmer into place and secure with mounting screws. Make sure disconnect switch at bottom of master is fully pushed inBlack1.3WhiteBlackBare1.1 1.41.21.5MasterBlackBlackGreenRedBlackWhiteWhite1.31.6 TOP1.4Tag -To LightTag- HotTroubleshooting GuideSymptom Possible Cause SolutionNo Function. All LEDs are OFF A) Light bulb(s) burned outB) Circuit breaker is off or trippedC) Disconnect switch on the dimmer is pulled out to the OFF positionD) Improper wiringE) Defective dimmerA) Replace light bulbB) Turn on the circuit breakerC) Push in the disconnect switch on the dimmerD) Check and correct wiringE) Replace dimmerErratic operation or flickering LEDsA) Loose wiring connectionsB) Low dim setting (RF9640-N)A) Check and correct wiringB) Set minimum brightness to a higher level (RF9640-N)Lights turns on after long delayA) Rapid start feature is disabled (RF9640-N)B) Low dim setting (RF9640-N)A) Enable rapid start feature (RF9640-N)B) Set minimum brightness to a higher level (RF9640-N)Functions normally using the dimmer push buttons but not from Z-Wave controller and one of the blue LEDs blinks ON and OFF about once per secondDimmer is not included in Z-Wave networkInclude dimmer in a Z-Wave network using a Z-Wave controller. Refer to Z-Wave controller user manual for detailsFunctions normally using the Master dimmer control but not from Z-Wave controller and no LEDs are blinkingProblem with RF communica -tion on dimmerReplace dimmerFunctions normally both locally and from a Z-Wave controller but can’t be controlled from a dimmer accessory switch (RF9642-Z) or other Z-Wave deviceThe dimmer accessory or other Z-Wave device is not associated with the dimmer you wish to controlCreate an association between the dimmer acces -sory or other device and the dimmer. Refer to your Z-Wave controller user manual for detailsDimmer is warm to touch after a period of timeThis is normal No action required
FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.—Increase the separation between the equipment and receiver.—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF exposure statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment.This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés.Installation et mise en œuvre de ce matériel devrait avec échangeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.

Navigation menu