Cooper Wiring Devices RF9642Z Z-Wave Plus Accessory Dimmer User Manual
Cooper Wiring Devices Inc Z-Wave Plus Accessory Dimmer
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 4045916 |
| Application ID | HM+ySPI2nuoReEFynUZy+w== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 207.01kB (2587567 bits) |
| Date Submitted | 2018-10-23 00:00:00 |
| Date Available | 2018-10-23 00:00:00 |
| Creation Date | 2018-10-19 10:03:49 |
| Producing Software | Adobe PDF Library 10.0.1 |
| Document Lastmod | 2018-10-23 19:02:40 |
| Document Title | User Manual |
| Document Creator | Adobe InDesign CS6 (Windows) |
Troubleshooting Guide ON/OFF Button Press to BRIGHTEN Light level indicators (blue) Light level may be adjusted with lights ON or OFF LED ON/OFF indicator (amber) Symptom Possible Cause Solution No Function. All LEDs are OFF A) Light bulb(s) burned out B) Circuit breaker is off or tripped C) Disconnect switch on the dimmer is pulled out to the OFF position D) Improper wiring E) Defective dimmer A) Replace light bulb B) Turn on the circuit breaker Erratic operation or flickering LEDs A) Loose wiring connections B) Low dim setting (RF9640-N) A) Check and correct wiring B) Set minimum brightness to a higher level (RF9640-N) Lights turns on after long delay A) Rapid start feature is disabled (RF9640-N) B) Low dim setting (RF9640-N) A) Enable rapid start feature (RF9640-N) B) Set minimum brightness to a higher level (RF9640-N) Functions normally using the dimmer push buttons but not from Z-Wave controller and one of the blue LEDs blinks ON and OFF about once per second Dimmer is not included in Z-Wave network Include dimmer in a Z-Wave network using a Z-Wave controller. Refer to Z-Wave controller user manual for details Functions normally using the Master dimmer control but not from Z-Wave controller and no LEDs are blinking Problem with RF communica tion on dimmer Functions normally both locally and from a Z-Wave controller but can’t be controlled from a dimmer accessory switch (RF9642-Z) or other Z-Wave device The dimmer accessory or other Z-Wave device is not associated with the dimmer you wish to control Create an association between the dimmer acces sory or other device and the dimmer. Refer to your Z-Wave controller user manual for details Dimmer is warm to touch after a period of time This is normal No action required Press to DIM Disconnect Switch Pull out to change bulbs (Master Dimmer only) Hot Red Black MASTER DIMMER 120V Green White Light Fixture Ground Neutral Neutral White Hot Green Black ACCESSORY DIMMER 120V White Ground Neutral White C) Push in the disconnect switch on the dimmer D) Check and correct wiring E) Replace dimmer Replace dimmer White Single Location Control Installation (requires one Master dimmer) 1.1 1.3 1.4 1.2 White Green Tag White Red ACCESSORY Black To Light Green Disconnect Switch Black Master Control Black Accessory Identify existing wiring (This switch will be a single-pole) and tag “Hot” wire. Use Disconnect existing switch and remove. voltage tester as necessary to confirm “Hot” wire (Voltage will be present at the “Hot” wire when the lights are off). 1.4 1.6 Tag White White ACCESSORY Green Black White Bare ACCESSORY Black Black - Hot Switch Identification Master 1.5 1.3 TOP Gently push dimmer into place and secure with mounting screws. Make sure disconnect switch at bottom of master is fully pushed in Red Black Connect master dimmer as shown by connecting black wire of dimmer to tagged “Hot” wire. Red wire must be connected to the wire that goes to the light. FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. ISED RSS Warning: This device complies with Innovation, Science and Economic Development Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'ISED applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. ISED RF exposure statement: This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Le rayonnement de la classe b repecte ISED fixaient un environnement non contrôlés.Installation et mise en œuvre de ce matériel devrait avec échangeur distance minimale entre 20 cm ton corps.Lanceurs ou ne peuvent pas coexister cette antenne ou capteurs avec d’autres.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Create Date : 2018:10:19 10:03:49+08:00 Creator : Adobe InDesign CS6 (Windows) Modify Date : 2018:10:23 19:02:40-07:00 Has XFA : No XMP Toolkit : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26 Metadata Date : 2018:10:23 19:02:40-07:00 Creator Tool : Adobe InDesign CS6 (Windows) Thumbnail Width : 256 Thumbnail Height : 168 Thumbnail Format : JPEG Thumbnail Image : (Binary data 17176 bytes, use -b option to extract) Instance ID : uuid:9bd97d0f-3d49-437b-a517-3428fbae0367 Original Document ID : xmp.did:6F7577EEFEBAE111B1B5EF88202884DC Document ID : xmp.id:60455DA241D3E8118DFF853B4EF33AA8 Rendition Class : proof:pdf Derived From Instance ID : xmp.iid:0185d9bd-cebc-e043-a1d7-69bd018a9d73 Derived From Document ID : xmp.did:5F455DA241D3E8118DFF853B4EF33AA8 Derived From Original Document ID: xmp.did:6F7577EEFEBAE111B1B5EF88202884DC Derived From Rendition Class : default History Action : converted History Parameters : from application/x-indesign to application/pdf History Software Agent : Adobe InDesign CS6 (Windows) History Changed : / History When : 2018:10:19 10:03:49+08:00 Format : application/pdf Producer : Adobe PDF Library 10.0.1 Trapped : False N Pages : 1 Has Visible Transparency : False Has Visible Overprint : True Max Page Size W : 412.750000 Max Page Size H : 279.400000 Max Page Size Unit : Millimeters Font Name : Myriad-Roman, Univers-CondensedLight, Univers-Condensed, Univers-CondensedBold, Univers-Bold, UniversCondensed-Medium, UniversCondensed-Bold, UniversLTStd-Cn, UniversLTStd-BoldCn, AvantGarde-CondBold Font Family : Myriad, Univers, Univers, Univers, Univers, Univers Condensed, Univers Condensed, Univers LT Std, Univers LT Std, AvantGarde CondBold Font Face : Roman, 47 Light Condensed, 57 Condensed, 67 Bold Condensed, 65 Bold, Medium, Bold, 57 Condensed, 67 Bold Condensed, CondBold Font Type : Open Type, Type 1, Type 1, Type 1, Type 1, TrueType, TrueType, Open Type, Open Type, Unknown Font Version : Version 001.000, 001.000, 001.000, 001.000, 001.001, Version 1.3 (Hewlett-Packard), Version 1.3 (Hewlett-Packard), OTF 1.029;PS 001.003;Core 1.0.33;makeotf.lib1.4.1585, OTF 1.029;PS 001.002;Core 1.0.33;makeotf.lib1.4.1585, Version 2.102;PS 2.000;hotconv 1.0.67;makeotf.lib2.5.33168 Font Composite : False, False, False, False, False, False, False, False, False, False Font File Name : Myriad-Roman.otf, Univers0_0.PFB; Univers0_0.pfm, Universp.PFB; Universp.pfm, Universg.PFB; Universg.pfm, Univers0.PFB; Univers0.pfm, unvr57w.TTF, unvr67w.TTF, UniversLTStd-Cn.otf, UniversLTStd-BoldCn.otf, MyriadPro-Regular.otf Plate Names : Cyan, Magenta, Yellow, Black, medium grey Swatch Group Name : Default Swatch Group Swatch Group Type : 0 Swatch Colorant Swatch Name : medium grey Swatch Colorant Type : SPOT Swatch Colorant Tint : 100.000000 Swatch Colorant Mode : RGB Swatch Colorant Red : 147 Swatch Colorant Green : 149 Swatch Colorant Blue : 151 Page Count : 2 AI Creator Version : 16.0.0 For : He, John, Title : IS9640.pdf Bounding Box : 27 34 1144 765 AI Build Number : 682 AI Color Usage : Color AI Ruler Units : Millimeters AI Color Model : RGB AI Target Resolution : 800 AI Num Layers : 1 Container Version : 11 Creator Version : 16 Image Height : 731 Image Width : 1117 Image Size : 1117x731 Megapixels : 0.817EXIF Metadata provided by EXIF.tools