Craftsman 11327521 User Manual BENCH SAW 10 INCH TILTING ARBOR. Manuals And Guides 1008043L

User Manual: Craftsman 11327521 11327521 CRAFTSMAN CRAFTSMAN BENCH SAW 10-INCH TILTING ARBOR. - Manuals and Guides View the owners manual for your CRAFTSMAN CRAFTSMAN BENCH SAW 10-INCH TILTING ARBOR. #11327521. Home:Tool Parts:Craftsman Parts:Craftsman CRAFTSMAN BENCH SAW 10-INCH TILTING ARBOR. Manual

Open the PDF directly: View PDF .
Page Count: 8

Download
Open PDF In Browser	View PDF

OPERATING
AND

INSTRUCTIONS

PARTS LIST FOR

|smqE

10-inch Tilting
,

, Model

Arbor

Number

113.27521
The
your
tion
your

above Model Number will be found on a plate attached to
saw, at the back, near the bottom of the base. Always menthe Model Number when communicating
with us regarding
saw or when ordering parts.

Instructions

for Ordering

Parts

All parts listed herein must be ordered through a Sears retail store
or mail order house. Parts are shipped prepaid.
When ordering
repair parts, always give the following information:
1. The part number.
2.

The part name.

The model number,

proper parts service. We suggest you keep it with other valuable
This
papers.list is valuable. It will assure your being able to obtain

...........
i

i •
i

CHECK

H O M
[
/
!

Figure

ARBOR

NUT-

Remove

two screws (B, fig. 1)
Check tightness
of

and lift out the insert (A, fig. 1).
saw arbor nut (part 6362, fig. 5),
using wrench (M, fig. 1).
Replace insert and screws.

""--_'I

ALIGN SAW BLADE WITH
TABLE GROOVESUsing elevation hand wheel (A, fig. 2),
set saw blade for deepest cut.
Make pencil mark on tooth that
is just above table top at front of
blade. Measure distance from this
tooth point to right-hand table
groove (L, fig. 1). Rotate blade by hand to place this
same tooth just above table top at rear
then again
measure distance from tooth point to right-hand groove.
The two measurements must be exactly equal.
If not,
loosen the three screws (part S-860, fig. 4) in each trunnion which secure the table trunnion (part 13, fig. 4) to
the table. Shift the two trunnions until the two measurements are equal, then retighten the screws. Again check
measurement.
INSTALL RIP FENCE-

Secure the rack (J, fig. 1) to

_our

examine

it carefully

for loose

rack parallel with the top of table. Pull the rip fence knob
(G, fig 1) out to pera_it the guide of the rip fence (F,
fig. 1 ) to slide over rack ( J, fig. 1 )
then place the. rip
fence on the saw table as shown in figure 2. A shght
pressure must be exerted on the rip fence to cause it to

Slide fence along
and table top.
If
sliding pad at the
clearance between
fenc( is
This

rack, noting clearance
between
fence
any part of the fence (other than the
rear) drags on the table top, or if the
fence and table varies apl_reciably as
(j, fig. 1) must then be readjusted.
again loosening
screws (D, fig. 1)

;PARALLEL
TO SAW
next to the right-hand
NOTICE
Fence
\

and
the

moving the motor support assembly towards or away from
the cradle.
Motor should be allowed to rest or hang
against the belt to obtain the automatic belt tightening
featureand belt should be snug. If adjustment is correct, clamp the motor support in place by tightening the
two square head set screws (part S-1267, fig. 4).
ADJUSTING
MOTOR
MOUNT
TENSION,
Tension
is adjusted
by tightening
the nut (part S-1215, fig. 4)
against the steel washer
(part S-1261)
and the spring
washer (part 6423). Nut should be tightened
just enough
to reduce motor vibration
when saw is operating.
Do
NOT tighten nut to a locked position,
or the stud will be
sheared off when blade is raised or lowered.
A sliding
action is necessary because mount
changes
position
as
blade is raised or lowered.
Operate
the saw by hand to
make certain that the belt has proper
tension and that
mount changes position
as it should.
If saw is to be driven by a large frame motor that cannot
be mounted
on the motor support
assembly, mount
the
motor on motor rails.
Use a 1/2-inch
wide belt with a
minimum length of 80 inches.
Adjust the position of the
motor until belt clears all obstructions
through all positions of the saw blade.
If saw is to be driven from a line shaft,
100 inches long.

use a belt at least

PLACEMENT OF MITER GAGEThe miter gage assembly (K, fig. 1) can be used in either one of the two
table grooves.

This saw is designed to be used with a 3450 rpm motor.
Motor should be 3/4 hp (for light duty) or one hp (for
heavy duty)in either an AC motor of a repulsioninduction or capacitor type, or a compound-wound
DC.
The motor shaft center siaould be approximately 4 inches
above the bottom of the motor base. If this dimension
varies appreciably from 4 inches, it may be necessary to
obtain a belt of a different length. If a 1750 rpm motor
with a 4-5/8-inch shaft center height is used, a 5-inch
motor pulley and a 46-inch belt must be purchased.
If
the motor shaft center height varies greater or smaller
than the above dimension, a correspondingly
greater or
smaller belt length should be used. _hese may be ordered
through any Sears Retail Store or Mail Order House.

Figure
ELEVATION
HAND
the saw, controls

WHEEL
elevation

(A)on the front
of the blade.

CLAMP SCREW HANDLE (D)
on front of saw, locks
the tilt mechanism in any desired position.
The
clamp screw handle operates like a socket wrench.
Tilt mechanism should always be locked before starting work
and should always be unlocked before
attempting to change the angle of tilt.
TILT HAND WHEEL (B)
on left side of saw, controis the angle of tilt. The saw blade can be tilted
from 0° to 45 °, as indicated on the TILT GAGE
(C).
If the angle of cut (tilt) must be extremely_
accurate, the angle of the saw blade should be
checked with a protractor or with a board which is
known to be cut at the exact angle required.
RIP FENCE (E) -- is operated by pushing in the FENCE
KNOB (F) so that it engages a pinion gear with
the teeth on RACK (H).
Turning the knob (F),
after pushing it in, will cause the rip fence to move
accurately across the table. When the knob (F) is
pulled out to disengage pinion gear, the rip fence
can be moved across the table by hand. Keep the
saw table and rip fence clean. Dirt may prevent the
rip fence from obtaining
proper
alignment.
Tapping
the fence lightly to assist the mechanism to find its
natural position, will help to maintain alignment of
the fence with the blade.
CAM

CLAMP LEVER (G)m
is used to clamp the rip
fence in place after it has been moved to the position
desired.

MITER GAGE (J) w is used in table grooves as a guide
for the workpiece when the fence is not used. The
angle of the gage can be adjusted by loosening
CLAMP KNOB (K) and positioning gage as indi-

CAUTION
Under no circumstances should a 5-inch motor
pulley be used with a 3450 rpm motor. The saw
blade speed resulting from such a pulley ratio
would be dangerous.
Do not use a 2fi_-inch
motor pulley _Tith a 1750 rpm motor --_is
will
not g ive satisfactory saw P erformance,

cated by the dial and pointer on (J).
MITER GAGE STOP ROD (L)--can
be adjusted in
length by loosening WING NUT (M). TI_ rod is
useci as a positioning guide for the end of the workptece.

CAUTION
The

their uses.

See figure 2.
_3_

Under no circumstances sh_d
a blade with a
diameter greater than 10 inches: be _
with
this saw.

ADJUSTING

TILT

GAGE

an accurate square, set saw blade at
right angles tO table top. Then adjust
the pointer on the tilt gage (C, fig. 2)
to

ADJUSTIMITER
O
Using an accurate

so that it touches
of the saw blade-

Using

_-L_

cator at

ADJUSTING
i_

LEVER
lever
too

check this cut with the square. If cut
is accurate, set the pointer on the miter
gage scale (J, fig. 2)to "90".

(G,
or

CLAMP
action

tight

is too

be adjusted

decreasing

length

6407,

fig.

clamp

readjusting

properly

in a horizontal

lid!

effec-

the

rod (part
clamp

on the end of the clamp

When
lock

'_!ili

by in-

the

of the rip fence

is done

should

it can

This

fence.

-T

fig.

loose,

tive

CAM

If clamping

creasing

ADJUSTING
FENCE II_
_Adjust
right-hand
fence indicator
(part 135, fig. 4) by positioning fence

Figure

. Move fence to left

qtO_S

side of blade and adjust left-hand
indicator in like manner.

SCALE

square, block the _

the right side
then set indi-

adjusted,
position

6409,
rod

nut

fig. 4)
(part

rod in back of the
the

clamping

or slightly

lever

lower.

quire no additional lubrication.
Other parts requiring
lubrication should be oiled frequently with SAE No. 20
or No. 30 Automobile Engine Oil. See figure 3.
1N Table trunnions m in which cradle tilts.
P
Lift screw block, lift screw threads, and lift nut.
Q -- Tilt screw block, tilt screw threads, and tilt nut.
R--Friction
points in saw guard.
S--Spindle
arm pin and saw arbor housing guide
bosses.
T--Saw
tilt clamp screw.
AII other points where there is friction
between two
or more moving
surfaces
or where
a slip fit is
necessary for adjustment
purposes.
Special attention
should be given to the moving parts
in the rip fence and miter gage.

PUSH STICK

enters the work at an angle more nearly
parallel with the direction of feed. ancl
there
work

iS better opportunity
against
kicf_back.

to hold

the

.,NO. SOUARES,

/
I

RESAWmNG

RiPPiNG
Ripping is the sawing of wood with the grain. It is
generally done with the help of a fence as a guide to
position and maintain the work at the correct width for
the cut. Because the work is pushed along the fence, it
must have a reasonably straight edge to make sliding contact with the fence. Also, work must make solid contact
with the table, so that it will not wobble. Provide a
straight edge, even if this means temporary nailing of an
auxiliary straight edge board to the work. If workpiece
is warped, turn the hollow side down.
Use of the saw guard is recommended; and the splitter
should always be used in ripping operations. Wood cut
with the grain tends to spring the kerr closed and bind
the blade. If for any reason, splitter is not used, stop and
insert a wedge in the kerf just as soon as cut has passed
back of blade.
Set fence to desired width of cut, either by using the
scale on the fence guide bar, or by measuring the distance
between blade and fence. Fence is almost always used
on right-hand side of blade. Stand a little to the right
of center to avoid being sprayed with sawdust and to be
clear of work in case of a kickback.
Start saw and advance work, using left hand to hold it down and right
hand to push it forward. AS cut nears completion, move
left hand to safe distance from blade, and push work
through with right hand alone. Never reach in back of
blade with either hand to hold work down.
When there is less than the

saw.

and

mSm

Resawing is the cutting of thick
boards into thinner ones. It is
a ripping operation. Small boards
up to 3_8-inch maximum width
--can
be resawed in one pass;
but !arger boards up to 6l/_-inch
maximum require two passes, one
pass along each edge of the board.
When two cuts from opposite
edges are required, these should
be made to overlap 1/2 inch from the approximate center
of the board. If the first cut is too deep, the kerr will
close and bind the saw on the second cut, with danger of
kickback. Also, when the kerr closes, the two sides of
the cut are no longer parallel to the saw blade, and the
saw will cut into them to spoil their appearance.
Keep
same face of board against fence when making both cuts.

RHT

CROSSCUTTING
Crosscutting is the sawing of wood across r_ie grain.
Planks are milled with the grain running the length of
the plank. In crosscutting the long edge of the work is
placed across the table top. Therefore. the miter gage is
used as a guide instead of the fence. Most operators prefer to use the left-hand table groove. In this case, the
left hand is used to hold the work in contact with the
gage and to push work and gage toward the blade. The
right hand is free to assist, as required. If right-hand
groove is used, hand positions are reversed.
Ordinarily the gage is placed in the table groove with the
bar in front. When work is so wide that it completely

CROSSCUTTING

Continued

inch wide can be cut.
chippers cannot.

covers table in front of blade, the
gage should be reversed. Square

__f,_,_
_-'_
_
_ii',iUlltl

(phonograph needles are excellent) or sandpaper, the extension
will help prevent side creep of
the work. If workpiece overhangs
table enough to sag at each end,
provide.
.
supports the same as in
rtppmg operations. The stop rod
_/:
on the miter gage, or a stop block _/_
fastened to _e _ension,
is used ___,
to fix position of left-hand edge __/_/

luIlt_
tlllll_

/_fw_
:
//_
€
_/}(I
\_
'_ '_----"
_/_
t\
_._'

:_i
I"

BEVEL AND MITER CUTS
Bevels from 1° to 45 ° are cut by tilting the saw blade
Operations are me"same as for ripping'
" or crosscutu'ng_"
but work should be extra well sup_ortecl to prevent creep,
Miters are crosscuts at an angle
to the edge of the workpiece. The _
miter gage is set at the required
angle to make the cut. Here also,
•"
-- "- ' n r
precauuons must De rage to p event creep.
_
.i:
_:

HEAD

The dado saw or head, as it is

chippers are used, stagger the swaged ends as evenly as
possible around the circumference.
Fractional
adjustments in thickness of the head can be made by using
paper washers between the outside blades and chippers.
Dado head operations are much
the same as those with a standard
blade _ but the dado head takes
a bigger bite, so that workpiece
should be held more firmly. It is
good practice to use a hold-down
jig like the one illustrated.

of work for measuring length of

USE OF THE DADO

blades can be used alone,

A dado insert (part 9-2212, fig. 4) must be used to replace the standard table insert. Whenever two or more

cr scuttlng
isdone
with
the;niter
gage set at "90" (at a right angle
to the slide and groove).
"l-'he
splitter need not im removed, but
is not needed for this operation.
Start_ the cut slowly and hold work
firmly to table to prevent kickback or Chatter.
(Loosely held
workpieces will sometimes vibrate
against table when crosscutting.
tends to bind blade and dull
teeth.)
An auxiliary wooden extension bolted to miter gage
greatly improves the gage as a
sup p oft • If fitted with pin points

Outside

When a groove wider than the
dado head is needed, make two
or more passes. Best method is
to use a notched stop block to position each successive cut. Block

is fastened to edge of table where
it can be used to position work
before starting the cut; but in such a position that it will
not contact work during the cutting operation.
cuts so that they overlap a trifle.

Space

When cutting a gain _ a groove that is closed at one
end
use a stop block to fix the end of the cut. To locate the stop, place work alongside dado head in position
in wh ...............
mn It wm De when cut Is nmsneo, then rig the stop
at the end of the work. When
cutting a stopped groove---which
is closed at both ends--also use
a starting block, as shown in the I
•.....
_._ ......
umstratlon.

£111S

same manner

as the stop block.

locatea

SANDING
A sanding
mounted
'forfine

instructions

for Ordering

All parts illustrated in Figures No. zi and No. 5
and listed on the following pages under part numbers must be ordered through a Sears Retail Store
or Mail Order House. Many screws, nuts, washers,
etc., are standard items and may be purchased locally by noting the specifications listed for these parts.

Parts

In several instances part numbers are listed for
COMPLETE ASSEMBLIES.
The part numbers of
the COMPLETE ASSEMBLIES, however, do not
appear on the illustrations.
All parts are shipped prepaid within the limits
of the continental United States.

6461

S-1267-N_

S- 1274----_

9-2212

FIGURE 4 PARTS LIST
Part NO.
64[03
87
88
91
92
93
126

Part No.

NAME OF PART
MITRE
Mitre
Mitre
Mitre
Mitre
Mitre
Mitre

NAME OF PART

Part

No.

17
18
19
55
54
55
56

GAGE ASSEMBLY
Gage Washer
Clamp Knob
Exten. Rod (S_aight)
F,xten. Rod
Rod Clamp
Thumb Screw

6_;05
6506
6511
6461

, Rod

S-298

Front
Table
ot
parts

included

the

three

the

complete

blocks

are

pare
not

NAME

PART

Clamp
Screw
Clamp
Screw
Handle
Clan_p
Screw
Spring
Tilt Lift
Pointer
Tilt Bearing
Bracket.
Tilt Bearing
Plate
Tilt
Screw
Block

Fence
Sfide
Gear
Extension
Rack
Table
Extension
Table
380

x 7/8

Rack

x I/t6

Steel

Washer

Panel
Tnmnion
_cetumed

furnished

to the
with

the

manufacturer
saw.

See

for

repairs.

page

:8 for

ordering

l_rmc_ien

these

items.

S- 1289

Figure

FIGURE 5 PARTS LIST

Part

No.

6392

NAME
SAW

ARBOR

PART

HOUSING

27
3508
3509
3513
6362

Loose
Collar
Arbor
Bearing
Retaivex
Saw
Arbor
Bearing
Saw Arbor
Key
Saw
Arbor
Nut

6383
6393
6380

Saw
Saw
Saw

S-I211
5570
14

Spring
CRADLE
Cradle

Arbor
Arbor
Arbor

Shaft
Snap
Assembly
Housing

Arm

The following

PART

Fil.

Hd.

S-203

5/16---18
x 3/4
Screw

5 / i6"/-18X
_crew
5/16

SAE

Arbor

Hex.

7/8
Med.

Part

PART

Retaining

Spindle
.Arm
Retaining
Washer,
Lift Screw
Block
Lift Nut
Tilt
Nut
Splitter
Blade
Clamp
Washer

* 70
3540
3557

Splitter
Blade
Clamp
Arbor
Wrench
Lift Nut
Washer

6084

Tilting

6085

Saw

Screw
Arbor

Spring

* S-970
* S-1066
S.1212
S-1262
8-1271
S-1283

Spacer
Retaining

Stud

Hex.

Hd.
Hd.

Part No.

NAME

standard
OF

Mach.

* S-1090

Cap

S-1156

9/16

S-1204

1/2...-13

13/16

S-1205
S-1206

1/2--13
5/16--18

15/16
x 7/32

Cap

Lockwashe_

x 1-3/8
Washer

x 7/16

NAME

7/16
7/16

x 3/4
x 3/4

Hex.

x .0239
x .0299

Steel
Steel

Washer
Washer

NAME
x
Hd.

locally:
OF

PART

S-1266

8---32

S-1267
S*1268

5/16--18
5/16--18

Nut

S-1272

8---32 Cap
x 5/16Screw
Pan

Hd.

Math.

Screw

Nut

S-1274
S-1275

10--32
10---32

1/8
Hd.

Hex.
Math.

Nut
Screw

Steel

x 5/16
Jam
Hex. Nut

PART

Spring
Washer
Spring
Washer
.758 x 1 x 1/32
Fibre
Washer
.695 x 15/16
x 1/64
Steel
Washer

Part I_o.

Flat

Tilt
Lift Nut
Bracket
Lift Screw
Collar
Lift
Screw
Retaining
Ring
Saw
Base
Assembly
Stop
Collar
Tilt
Screw

and can be purchased

PART

7/64

No.

6302
6326
6328
6331
6355
6451
6459

Stud

30
38
39
58
* 69

parts shown on Figures 4 and 5 are

NAME

....

NAME
Saw

Washer

10---32
x 1/2
Screw

_2_1

S-112

S-275

Ring

Washer
h_SSEMBLY

Spindle

Part No.

Part No.
ASSY.

5/16
Pan
Hd.
Mach.
Screw
x 5/8
Sq.
x 1-3/16

x 3/8
x
x 1/2 Rd.

Rd.

Hd. Set Screw
Her.
Hd.

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 8
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Fri Mar 28 21:24:16 2014
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 11327521 User Manual BENCH SAW 10 INCH TILTING ARBOR. Manuals And Guides 1008043L

Navigation menu

Versions of this User Manual:

Views

Navigation