Craftsman 137218070 User Manual TABLE SAW/STAND Manuals And Guides L0810542

CRAFTSMAN Saw Table Manual L0810542 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

User Manual: Craftsman 137218070 137218070 CRAFTSMAN TABLE SAW/STAND - Manuals and Guides View the owners manual for your CRAFTSMAN TABLE SAW/STAND #137218070. Home:Tool Parts:Craftsman Parts:Craftsman TABLE SAW/STAND Manual

Open the PDF directly: View PDF .
Page Count: 56

Download
Open PDF In Browser	View PDF

Operator's lVlanual

ERRFrSNRN°
10-in. TABLE SAW WiTH LEG SET
Model No. 137.218070

CAUTION:
Before using this Table Saw,
read this manual and follow
all its Safety Rules and
Operating Instructions
Customer
Help Line
For Technical
Support
1-800-843-1682

®
®
®
®
®

Safety Instructions
Installation
Operation
Maintenance
Parts List

Sears Parts &
Repair Center
1-800-488-1222

Sears, Roebuck

and Co., Hoffman Estates, IL 60179 USA

Visit our Craftsman

website:

Part No. 137218070001

www.sears.comlcraftsman

Printed in Taiwan

SECTION
Warranty .................................................................................................
Product Specifications ............................................................................
Symbols ..................................................................................................
Power Tool Safety ..................................................................................
Table Saw Safety ....................................................................................
Electrical Requirements and Safety ........................................................
Accessories and Attachments ................................................................
Tools Needed for Assembly ....................................................................
Carton Contents .....................................................................................
Know Your Table Saw ............................................................................
Glossary of Terms ..................................................................................
Assembly .................................................................................................
Adjustments ............................................................................................
Operation ................................................................................................
Maintenance ...........................................................................................
Troubleshooting Guide ...........................................................................
Parts List .................................................................................................

CRAFTSMAN

ONE YEAR

PAGE
2
3
4
5
8
10
12
12
13
15
16
18
28
34
43
45
48

FULL WARRANTY

If this Craftsman tool fails due to a defect in material or workmanship within
one year from the date of purchase, call 1-800-4-MY-HOME®to
arrange for
free repair (or replacement if repair proves impossible).
This warranty applies for only 90 days from the date of purchase if this product
is ever used for commercial or rental purposes.
This warranty does not include expendable parts, such as lamps, batteries,
bits or blades.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179

WARNING

]

Some dust created by using power tools contains chemicals known to the state
of California to cause cancer and birth defects or other reproductive harm.
Some examples of these chemicals are:
o Lead from lead-based paints
o Crystalline silica from bricks, cement and other masonry
products
•
Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do
this type of work. To reduce your exposure to these chemicals, work in a
well ventilated area and work with approved safety equipment such as dust
masks that are specially designed to filter out microscopic
particles.
2008/05

2 ..........................................................................................................................

MOTOR
Type .............................................................................
Amperes .......................................................................
Voltage ........................................................................
Hz ................................................................................

Universal
15 Amp
120V AC
60Hz

RPM (no load) ............................................................
Overload Protection ....................................................

5000 RPM (No load)
Yes

BLADE SIZE
Diameter ......................................................................
Arbor size ....................................................................

10 in.
5/8 in.

SAW
Rip fence ......................................................................
Miter gauge ..................................................................
Rip Capacity ................................................................
Maximum Cut Depth @ 90° .........................................
Maximum Cut Depth @ 45 ° .........................................
Maximum Diameter Dado ............................................
Maximum Dado Cut Width ...........................................

Yes
Yes
24 in. Right & Left
3 in.
2-1/2 in.
6 in. (Stackable only)
1/2 in.

{,,i_ WARNING]
To avoid electrical hazards, fire hazards or damage to the tool, use proper
circuit protection.
This tool is wired at the factory for 110-120 Volt operation, it must be
connected to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker.
To avoid shock or fire, replace power cord immediately if it is worn, cut or
damaged in any way.
Before using your tool, it is critical that you read and understand these
safety rules. Failure to follow these rules could result in serious injury to
you or damage to the tool.

WARNING iCONS
Your power tool and its Operator's Manual may contain "WARNING iCONS"
(a picture symbol intended to alert you to, and/or instruct you how to avoid,
a potentially hazardous condition). Understanding
and heeding these
symbols will help you operate your tool better and safer. Shown below are
some of the symbols you may see.
SAFETY ALERT:

Precautions that involve your safety.

PROHiBiTiON

WEAR EYE PROTECTION: Always wear safety goggles or safety
glasses with side shields.
READ AND UNDERSTAND

OPERATOR'S

MANUAL: To reduce

the risk of injury, user and all bystanders must read and understand
operator's manual before using this product.
KEEP HANDS AWAY FROM BLADE: Failure to keep your hands away
from the blade will result in serious personal injury.
SUPPORT AND CLAMP WORK

i,_

DANGER

WARNING

DANGER: indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.

]

WARNING: indicates a potentially hazardous situation
which, if not avoided, could result in death or serious injury.

indicates a potentially hazardous situation which.
IA CAUTION]CAUTION:
if not avoided, may result in minor or moderate injury.

[ CAUTION

]

CAUTION: used without the safety alert symbol indicates
a potentially hazardous situation which, if not avoided,
may result in property damage.

GENERALSAFETY

iNSTRUCTiONS
BEFORE USING THiS POWER TOOL

Safety is a combination of common
sense, staying alert and knowing how
to use your power tool.

,A WARNING
To avoid mistakes

I
that could cause

serious injury, do not plug the tool in
until you have read and understood
the following.
.

READ and become familiar
with the entire Operator's
Manual. LEARN the tool's
application, limitations and
possible hazards.

2. KEEP GUARDS iN PLACE and in
working order.
3. REMOVE ADJUSTING KEYS
AND WRENCHES. Form the habit
of checking to see that keys and
adjusting wrenches are removed
from the tool before turning ON.
4. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.

6. KEEP CHILDREN AWAY. All
visitors and bystanders should be
kept a safe distance from work area.
7. MAKE WORKSHOP

CHILD PROOF

with padlocks, master switches or by
removing starter keys.
8. DO NOT FORCE THE TOOL. It will
do the job better and safer at the
rate for which it was designed.
9. USE THE RIGHT TOOL. Do not
force the tool or an attachment to do
a job for which it was not designed.
10.USE PROPER EXTENSION
CORDS. Make sure your extension
cord is in good condition. When
using an extension cord, be sure to
use one heavy enough to carry the
current your product will draw. An
undersized cord will result in a drop
in line voltage and in loss of power
which will cause the tool to overheat.
The table on page 11 shows the
correct size to use depending on
cord length and nameplate ampere
rating. If in doubt, use the next
heavier gauge. The smaller the
gauge number, the heavier the cord.
11 .WEAR PROPER APPAREL.

5. DO NOT USE iN DANGEROUS
ENVIRONMENTS. Do not use
power tools in damp locations, or
expose them to rain or snow. Keep
work area well lit.

not wear loose clothing, gloves,
neckties, rings, bracelets or other
jewelry which may get caught in
moving parts. Nonslip footwear is
recommended. Wear protective hair
covering to contain long hair.

12.ALWAYS
WEAR

EYE

tool can throw foreign
PROTECTION.
Any power
objects into the eyes
and
could cause permanent
eye damage. ALWAYS wear Safety
Goggles (not glasses) that comply
with ANSI Safety standard Z87.1.
Everyday eyeglasses have only
impact-resistant lenses. They
ARE NOT safety glasses. Safety
Goggles are available at Sears.
NOTE: Glasses or goggles not in
compliance with ANSI Z87.1 could
seriously injure you when they break.
13.WEAR A FACE MASK OR DUST
MASK. Sawing operation produces
dust.
14.SECURE WORK. Use clamps or
a vise to hold work when
practical. It is safer than
using your hand and
it frees both hands to

17.USE RECOMMENDED
ACCESSORIES. Consult
this Operator's Manual for
recommended accessories. The use
of improper accessories may cause
risk of injury to yourself or others.
18.NEVER STAND ON THE TOOL.
Serious injury could occur if the
tool is tipped or if the cutting tool is
unintentionally contacted.
19.CHECK FOR DAMAGED

PARTS.

Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate
properly and perform its intended
function - check for alignment of
moving parts, binding of moving
parts, breakage of parts, mounting
and any other conditions that may
affect its operation. A guard or other
part that is damaged should be
properly repaired or replaced.

operate the tool.
20.NEVER LEAVE THE TOOL
1&DISCONNECT

TOOLS FROM

POWER SOURCE before servicing,
and when changing accessories
such as blades, bits and cutters.
16.REDUCE THE RISK OF
UNINTENTIONAL STARTING.
Make sure switch is in the OFF
position before plugging the tool in.

RUNNING UNATTENDED. TURN
THE POWER "OFF". Do not walk
away from a running tool until the
blade comes to a complete stop
and the tool is unplugged from the
power source.
21 .DO NOT OVERREACH. Keep
proper footing and balance at all
times.

22.MAINTAIN
TOOLSWITHCARE.
Keeptoolssharpandcleanforbest
andsafestperformance.
Follow
instructions
forlubricating
and
changingaccessories.
23.WARNING:
Dustgenerated
from
certainmaterials
canbehazardous
toyourhealth.Alwaysoperatesaw
inwell-ventilated
areaandprovide
forproperdustremoval.
24"[,A

DANGER

People with electronic devices, such
as pacemakers, should consult
their physician(s) before using this
product. Operation of electrical
equipment in close proximity to
a heart pacemaker could cause
interference or failure of the
pacemaker.

1.ALWAYSUSESAWBLADE
GUARD,rivingknifeandantikickbackpawlsfor every throughsawing operation. Through-sawing
operations are those in which the
blade cuts completely through
the workpiece when ripping or
crosscutting. Always be sure blade
guard is tightened securely.
2. ALWAYS HOLD WORK FIRMLY

6. NEVER REACH behind or over the
cutting tool for any reason.
7. REMOVE the rip fence when
crosscutti ng.
8. DO NOT USE a molding head with
this saw.
9. FEED WORK INTO THE BLADE
against the direction of rotation only.

against the miter gauge or rip fence.
3. ALWAYS USE a push stick or
push block, especially when ripping
narrow stock. Refer to ripping
instructions in this Operator's Manual
where the push stick is covered in
detail. A pattern for making your own
push stick is included on page 47.
4. NEVER PERFORM ANY
OPERATION FREEHAND, which
means using only your hands to
support or guide the workpiece.
Always use either the fence or the
miter gauge to position and guide
the work.

DANGER[

FREEHAND CUTTING IS THE
MAJOR CAUSE OF KICKBACK AND
FINGER/HAND AMPUTATIONS.
NEVER USE THE MITER GAUGE
AND FENCE SIMULTANEOUSLY.
5. NEVER STAND or have any part of
your body in line with the path of the
saw blade. Keep your hands out of
the saw blade path.

10.NEVER use the rip fence as a cutoff gauge when crosscutting.
11 .NEVER ATTEMPT TO FREE A
STALLED SAW BLADE without
first turning the saw OFF. Turn
power switch OFF immediately to
prevent motor damage.
12.PROVIDE ADEQUATE SUPPORT
to the rear and the sides of the saw
table for long or wide workpieces.
13.AVOID KICKBACKS (work thrown
back towards you) by keeping the
blade sharp, the rip fence parallel
to the saw blade and by keeping
the riving knife, antFkickback pawls
and guards in place, aligned and
functioning. Do not release work
before passing it completely beyond
the saw blade. Do not rip work that
is twisted, warped or does not have
a straight edge to guide it along the
fence. Do not attempt to reverse out
of a cut with the blade running.
14.AVOID AWKWARD OPERATIONS
and hand positions where a sudden

slipcouldcauseyourhandto move
intothesawblade.
15.NEVER
USESOLVENTS
to
cleanplasticparts.Solventscould
possiblydissolveor otherwise
damagethematerial.Onlya soft
dampclothshouldbeusedtoclean
plasticparts.
16.MOUNT
yourtablesawona
benchor standbeforeperforming
anycuttingoperations.
Referto
ASSEMBLY
onpage20.
17"1,_ WARNING

]

Never cut metals or masonry
products with this tool. This table
saw is designed for use on wood
and wood-like products.
18.ALWAYS USE IN A WELL=
VENTILATED AREA. Remove
sawdust frequently. Clean out
sawdust from the interior of the saw
to prevent a potential fire hazard.
19.NEVER LEAVE THE SAW
RUNNING UNATTENDED. Do not
leave the saw until the blade comes
to a complete stop.
20.For proper operation follow the
instructions in this Operator's Manual
entitled OPERATION (Page 34).
NOTE: On machines with no stand
or if stand is not being used, a hole
approximately 11 in. square must
be cut under saw to allow sawdust
to fall through. Failure to cut this
hole will allow sawdust to build up
in the motor area, resulting in a fire
hazard and potential motor damage.

21 .USE ONLY saw blades recommended with warning that the riving
knife shall not be thicker than the
width of the groove cut by the saw
blade and not thinner than the body
of the saw blade.
22.USE PUSH-STICK

OR PUSH

BLOCK to feed the workpiece past
the saw blade. The push-stick or
push block should always be stored
with the machine when not in use.
23.Use and correct adjustment of the
riving knife.

GROUNDING

iNSTRUCTiONS

IN THE EVENT OF A MALFUNCTION
OR BREAKDOWN, grounding provides
a path of least resistance for electric
currents and reduces the risk of electric
shock. This tool is equipped with an
electrical cord that has an equipmentgrounding conductor and a grounding
plug. The plug must be plugged into
a matching receptacle that is properly
installed and grounded in accordance
with all local codes and ordinances.
DO NOT MODIFY THE PLUG
PROVIDED. If it will not fit the
receptacle, have the proper receptacle
installed by a qualified electrician.
iMPROPER CONNECTION of the
equipment grounding conductor can
result in risk of electric shock. The
conductor with the green insulation
(with or without yellow stripes) is the
equipment grounding conductor. If
repair or replacement of the electrical
cord or plug is necessary, do not
connect the equipment grounding
conductor to a live terminal.
CHECK with a qualified electrician or
service person if you do not completely
understand the grounding instructions,
or if you are not certain the tool is
properly grounded.
USE only three-wire extension cords
that have three-pronged grounding
plugs with three-pole receptacles that
accept the tool's plug. Repair or replace
damaged or worn cords immediately.

GUiDELiNES

FOR EXTENSION

CORDS
USE THE PROPER EXTENSION
CORD. Make sure your extension cord
is in good condition. Use an extension
cord heavy enough to carry the current
your product will draw. An undersized
cord will cause a drop in line voltage
resulting in loss of power, overheating
and burning out of the motor. The
table on the right shows the correct
size to use depending on cord length
and nameplate ampere rating. If in
doubt, use the next heavier gauge. The
smaller the gauge number, the heavier
the cord.
Make sure your extension cord is
properly wired and in good condition.
Always replace a damaged extension
cord or have it repaired by a qualified
technician before using it. Protect your
extension cords from sharp objects,
excessive heat and damp or wet areas.
Use a separate electrical circuit for
your tool. This circuit must not be less
than #12 wire with a 20 A time-lag fuse
or a #14 wire with a 15 A time-lag
fuse. NOTE: When using an extension
cord on a circuit with a #14 wire, the
extension cord must not exceed 25 feet
in length. Before connecting the motor
to the power line, make sure the switch
is in the off position and the electric
current is rated the same as the current
stamped on the motor nameplate.
Running at a lower voltage will damage
the motor. This tool is intended for use
on a circuit that has a receptacle like
the one illustrated in Fig. 1.

Fig.1 showsa three-pronged
electrical
plugandreceptacle
thathasa
grounding
conductor.Ifa properly
groundedreceptacle
isnotavailable,
anadapter(Fig.2)canbeusedto
temporarily
connectthisplugtoa
two-contact
groundedreceptacle.
Theadapter(Fig.2) hasa rigidlug
extending
fromit thatMUSTbe
connected
toa permanent
earth
ground,suchasa properlygrounded
receptacle
box.

CAUTION
This tool must be grounded
while
in use to protect the operator from
electric shock.
O"

CAUTION
This tool is for indoor use only. Do
not expose to rain or use in damp
locations.
Fig. 1
Plug

g Prong
Properly Grounded
Three-Pronged Receptacle
Fig. 2
Grounding Lug _
/ _'_
_b_-,./ I_.

Make sure this
] is connected
to a known

,_"_.__!_
_zrt.J

Adapter '_

II ground.

Two-Pronged
Receptacle

O=t

Ampere Rating
Total length of Cord
More Than Not More Than 25ft. 50ft. 100ft. 150ft.

CAUTION
In all cases, make certain the
receptacle is properly grounded. If
you are not sure, have a qualified
electrician check the receptacle.

Three-Pronged

(When using 120 volts only)

:::::::::::::::::::::::::::::::

RECOMMENDED

ACCESSORIES

]

WARNING

SUPPLIED

Visit your Sears Hardware
Department or see the
Craftsman Power and Hand Tools
Catalog to purchase recommended
accessories for this power tool.

Blade wrench

WARNING]

To avoid the risk of personal injury:
o Do not use adjustable (wobble)
type dadoes or carbide tipped
dado blades.
e Only use stackable dadoes.
e Maximum dado width is 1/2 in.
e Do not use a dado with a diameter
larger than 6 in.
• Do not use molding head set with
this saw.
e Do not modify this power
tool or use accessories not
recommended by Sears.

NOT SUPPLIED

Flat bladed
screwdriver

#2 Phillips screwdriver

!!!!!!!!!!!

Straight edge
4 mm Hex
wrench
Adjustable wrench
and/or 8 mm, 13 mm,
14 mm wrench

Combination square

Separate all parts from packing
materials. Check each part with the
illustration on the next page and the
"Table of Loose Parts" to make certain
all items are accounted for, before
discarding any packing material.

I,A WARNING

]

if any part is missing or damaged,
do not attempt to assemble the
table saw, plug in the power
TABLE
ITEM
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
STAND
U
V
W
X
Y
Z
AA
BB
CC

cord, or turn the switch ON until
the missing or damaged part is
obtained and is installed correctly.
Call 1=800-843-1682 for missing or
damaged parts.
NOTE: To make assembly easier, keep
contents of box together. Apply a coat
of automobile wax to the table. Wipe all
parts thoroughly with a clean dry cloth.
This will reduce friction when pushing
the workpeice.

OF LOOSE PARTS
DESCRIPTION
Table saw assembly
Blade guard assembly
Anti-kickback pawls assembly
Handwheel handle
Riving knife hardware bag assembly
Rip fence
Miter gauge
Blade wrench
Push stick
Push stick storage holder
Rear table extension
Rear table extension tube
Table insert
Table extension wing hardware bag assembly
Hex wrench
Blade
Left and right extension table
Dust ba,q
Extension table hardware bag assembly
AAA Battery
Locking lever hardware bag assembly
Stand hardware bag assembly
Leq bracket
Bottom Ionq support bracket
Top long support bracket
Bottom support bracket for roller wheel
Bottom short support bracket
Top short support bracket
Roller wheel hardware bag assembly

QUANTITY
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1 each
1
1
2
1
1
4
2
2
1
1
2
1

UNPACKING

YOUR TABLE

SAW

%
J
F

N
L

S
T

Blade guard
Miter gauge

_ip fence

Left extension table

wing
locking lever
elevation and
tilting handwheet

Overload reset switch
Miter gauge-rip
fence-push stick storac

ON/OFF switch with
safety key

Lock

Footpad
Dustbag

switch
Blade

Riving knife

Table insert

pawls

Hand
Rear table extension wing
Right extension
wrap

Blade storac

Roller wheel

ANTI-KICKBACK

PAWLS - Prevents

the workpiece from being kicked
upward or back toward the front of the
table saw by the spinning blade.
ARBOR - The shaft on which the
blade or dado is mounted.

the workpiece from twisting during the
cutting operation.
GUM - A sticky sap from wood
products.
HEEL - Misalignment of the blade.

BEVEL CUT - An angle cut made
through the face of the workpiece.

JAMB NUT - Nut used to lock another

BLADE BEVEL SCALE - Measures

KERF - The amount of material

the angle the blade is tilted when set
for a bevel cut.

removed by the blade cut.

BLADE ELEVATION AND TiLTiNG
HANDWHEEL = Raises and lowers
the blade or tilts the blade to angle
between 0° and 45 ° for bevel cuts.
BLADE GUARD - Clear plastic cover
that positions itself over the blade while

nut in place on a threaded rod or bolt.

MITER CUT - An angle cut made
across the width of the workpiece.
MITER GAUGE - A guide used for
crosscutting operations that slides
in the table top channels (grooves)
located on either side of the blade. It

cutting.

helps make accurate straight or angle
crosscuts.

COMPOUND CUT - A simultaneous

OVERLOAD RESET SWITCH -

bevel and miter cut.

Protects the motor if it overloads during
operation, provides a way to restart the

CROSSCUT - A cut made across the

saw.

width of the workpiece.
PUSH STICK-

Used to push

DADO - Special cutting blades that are
used to cut grooves in a workpiece.

workpieces when performing ripping
operations.

FREEHAND - Performing a cut without
using a rip fence, miter gauge, hold
down or other proper device to prevent

PUSH BLOCK - Used for ripping
operation when the workpiece is too
narrow to use a push stick. Always use
a push block for rip widths less than 2 in.

FEATHERBOARD
- Whenripping
a workpiece
onyourtablesaw,this
keepsitfirmlyandsafelyagainstthe
ripfence.It alsohelpspreventchatter,
gouging,anddangerous
kickback.

TABLE INSERT - Insert that is
removed from the table to install/
remove blades. It is also removed for

REVOLUTIONS
PER

- The number of turns completed by a
spinning object in one minute.

THROUGH SAWING - Making a cut
completely through the length or width
of a workpiece.

RIP FENCE - A guide used for rip

WORKPIECE - Material to be cut.

dado cutting. When dado cutting, a
dado insert plate must be used.

MINUTE (RPM)

cutting which allows the workpiece to
cut straight.
Leadinc

Saw blade path

RIPPING - Cutting with the grain of
the wood or along the length of the
workpiece.
Trailing
edge

RIVING KNIFE - A metal piece of the
guard assembly located behind and
moves with the blade. Slightly thinner

Workpiece

than the saw blade, it helps keep the
kerf open and prevents kickback.
SAW BLADE PATH - The area of the
workpiece or table top directly in line
with the travel of the blade or the part
of the workpiece that will be cut.
SET - The distance between two saw
blade tips, bent outward in opposite
directions to each other. The further
apart the tips are, the greater the set.

ASSEMBLE STAND (FIG. A, B, C)
1. Unpack all parts and group by type
and size. Refer to the parts list for
correct quantities.
2. Attach four hooks (10) to the top
corner of the four legs (2) as shown.
The hooks (10) are used to hold the
dust bag.
NOTE: Make sure the hook (10) is
securely fastened to the corner of
the leg (2).
Fig. A

_. ....

3. Attach one long upper support with
label (1) to top of leg (2) using one
bolt (3) and nut (4).
NOTE:
o Align detents (8) in stand leg
with support brackets to ensure
proper fit.
o Do not tighten bolts until stand is
properly aligned.
o Position all supports to the
INSIDE of the leg assembles.
4. Attach short upper supports (6) to
other hole of leg (2) using one bolt
and nut.
Fig. B

5. Assemble the other upper supports
in exactly the same manner.
6. Attach one bottom support (5) to the
center of the leg using bolt (3) and
nut (4). This completes the front
frame section.
7. Assemble rear frame section in
exactly the same manner.
8. Join front-bottom and rear-bottom
frame assemblies using the bottom
support (7), bolts and nuts.
Fig. C

Front
ASSEMBLE THE ROLLER WHEEL
TO STAND (FIG. D, E)
1. Place stand upside down on level
surface or floor.
2. Place bottom support bracket for roller
wheel (18) inner of the front leg (2).
3. Insert the bolt (12) through the roller
wheel bracket (11), front leg (2),
bottom support bracket (18) and nut
(13) as shown. Tighten the nut.
4. Attach the roller wheel (14) to roller
wheel bracket (11), bolt (15) and lock
nut (16) using square neck bolt (15)
and lock nut (16) as shown.
NOTE: Do not overtighten nut as
this will not allow the wheels to turn.

Fig.D

Fig. F

11
.

Repeat steps 1-4 for left rear leg (17)
and roller wheel assembly.
NOTE: The roller wheel assemblies
and bottom support bracket (18)
can be installed on either the righthand side or left-hand side. Always
install the roller wheel assemblies
and the bottom support bracket (18)
at the same time. The illustration
shows the roller wheels on the lefthand side.
Fig. E

Front

6. Carefully set the saw in its upright
position on a clean level surface.
ASSEMBLE THE FOOT PAD TO
STAND (FIG. F)
1. Place all four foot pads (9) onto
each leg.
2. Place stand on level surface and
adjust so all legs are contacting the
floor and are at similar angles to the
floor, and detents in stand leg align
with support brackets, then tighten
all bolts.
NOTE: Stand should not rock after
all bolts are tightend.

ASSEMBLE TABLE SAW TO STAND
USING LEVER LOCK (FIG. G)
1. Attach the locking lever assembly (18)
to the top of the leg (2).
2. Lift up the locking lever (19).
3. Thread the two screws (20) into the
holes (21) of the locking bracket (24)
and stand.
NOTE: You may need to loosen
the two short support brackets if the
two mounting holes are not lined up
correctly. Retighten these bolts once
you have added the lever locks.
4. Attach the lock nuts (22) and tighten
with a 8 mm or adjustable wrench.
5. Install the other locking lever
assemblies in exactly the same
manner.
6. Position the saw base on the stand.
7. Line up the lever lock cover (23) to
the saw base and push down the
locking lever (19).
8. Fasten saw to stand using four
locking lever assemblies (18).
NOTE: The four locking lever
assemblies (18) are provided for
quick releasing the table saw to the
stand.

I,'_ WARNING]
All four levers must be locked in the
down position before operating saw.
Fig. G _
1

19 23
._2

MOUNTING BASE TO STAND USING
BOLTS (FIG. H)
You can also attach the saw base to the
stand using standard bolts.
,

Fasten the base to the stand using
the four long bolts (25), flat washers
(26), and nuts (27).
Place a washer on the bolt and insert
thru the hole in saw base and slot
in stand. Attach the nut and tighten
using a 13 mm wrench. Repeat for
other three corners.
Fig. H
25

5. Mark an 11 in. square (2) centered
between the four mounting holes (1).
6. Cut out and remove the square.
7. This opening will allow sawdust to
fall through the saw base.
8. Place the saw on the work surface,
and align the mounting holes of the
saw with those drilled through the
surface.
9. Fasten the saw to the work surface.

l_k WARNING

Do not operate this machine on the
floor. This is very dangerous and
may cause serious injury.
Fig. I
i

•

2
J

I_/SQUARE

co,oo,

JJJJJJ
•

jl
Ir

ASSEMBLING THE HANDWHEEL
SAW MOUNTED TO WORK
SURFACE (FIG. I)
1. If the leg set will not be used, the
saw must be properly secured to
a sturdy workbench using the four
mounting holes at the base of the
saw.

2. The surface of the table where the
saw is to be mounted must have
a hole large enough to facilitate
sawdust fall-through and removal.
3. Square the saw on the mounting
surface and mark the location of the
four 3/8 in. mounting holes (1).
4. Drill 3/8 in. hole into the mounting
surface.

HANDLE (FIG. J)
Thread the handwheel handle (1) into
the handwheel hole, and then tighten
the nut against the handwheel with a
14 mm or adjustable wrench.
Fig. J

RiP FENCE (FIG. K)
1. Lift upward on the rip fence handle
(1) so the rear holding clamp (2) is
fully extended.
2. Place the rip fence on the saw table,
and attach the set plate (3) under
the fence handle (1) to the rail first.
3. Push down on the fence handle (1)
to lock.
Fig. K

Fig. L

1
INSTALLING THE BLADE
(FIG. M, N, O)

WARNING]

To avoid injury from an accidental
start, make sure the switch is in the
OFF position and the plug is not
connected to the power source outlet.
1. Raise the blade arbor to the
maximum height by turning the blade
elevation handwheel clockwise.
2. Remove the arbor nut (2) and outer
blade flange (3). (Fig. M)
iNSTALLiNG THE DUST BAG (FIG. L)

WARNING]

o Do not use this saw to cut and/or
sand metals. The hot chips or
sparks may ignite sawdust or the
bag material.
o To prevent hazard, clean and
remove sawdust from under the
saw frequently.
1. The hooks (2) located inside of the
four legs are used to hold the dust
bag (1).
2. Attach the dust bag (1) to the four
hooks located inside of four legs.

Fig. M

3. Place the blade onto the arbor
(4) with the blade teeth pointing
forward to the front of the saw. (Fig. N)
4. Make sure the blade fits flush
against the inner flange.
5. Clean the outer blade flange (3)
and install it onto the arbor (4) and
against the blade. (Fig. N)

6.Threadthearbornut(2)ontothe
REMOVING THE BLADE (FIG. N, O)
arbor,makingsuretheflatsideof
I,A WARNING i
the nutis againsttheblade,then
hand-tighten.
(Fig.N)
To avoid injury from an accidental
7.Totightenthearbornut(2),place
start, make sure the switch is in
theopen-endwrench(5)ontheflats the OFF position and the plug is
ofthesawarborto keepthearbor
disconnected from the power source
fromturning(Fig.N).
outlet.
8. Placethebox-endwrench(6)onthe
arbornut(2)andturnclockwise(to
1. Remove the table insert by snapping
the rearofthesawtable).(Fig.N)
out from the hole (8). (Fig. O)
2. Raise the blade to the maximum
height by turning the blade elevation
handwheel clockwise.
3. Adjust the blade to the 90 ° vertical
position by unlocking the blade tilting
lock knob and turning the bevel
tilting handwheel counterclockwise,
and then lock into position.
4. Place the blade wrench (6) on the
arbor nut (2) (Fig. N).
5. Loosen the arbor nut (2), place the
open-end wrench (5) on the flats of
the saw arbor to keep the arbor from
turning (Fig. N).
6. Then remove the blade (7). Clean
but do not remove the inner blade
flange before reassembling the
blade (Fig. N).

10.Lower
thebladetoitsminimum
heightpositionandplaceinsert(1)
intoposition.(Fig.O)
Fig. O

RIVING KNIFE ASSEMBLY (FIG. P,
P-I, Q)

[_,
8

[,_L, WARNING]
To avoid possible injury and damage
to the workpiece, be sure to INSTALL
THE BLADE WITH THE TEETH
POINTING TOWARD THE FRONT OF
TABLE in the direction of the rotation
arrow on the blade guard.

WARNING]

o To avoid injury from an accidental
start, make sure the switch is in
the OFF position and the plug
is disconnected
from the power
source outlet.
o Never operate this saw without
the riving knife in the correct
position.

Installingthe riving knife assembly
(Fig. P, P=I)
1. Remove the table insert
2. With the blade elevation handwheel
(1), raise the blade arbor to the
maximum height.
3. Loosen the blade lock handle (2).
Just turn and move the handwheel
(1) to 45 ° on the bevel scale.
4. Tighten the bevel lock handle.
Fig. P

5. Take the lock knob (6) and insert
thru the washer (5), middle hole in
the set plate (4) and slot in riving
knife (7).
6. Place this assembly through the
mounting bracket (3) located behind
the saw blade. Please note that the
two pins on the bracket must be
engaged in the riving knife slot and
the two holes in the set plate.
7. Make sure the riving knife (7) is in
its highest position. Tighten the lock
knob (6).
8. Return the blade to 0 ° and place the
table insert in position.
9. Before using the saw, please follow
the instructions on aligning the

riving knife,

Fig. P-1 3 _54
6

\h__,

Aligning the riving knife (Fig. Q)

I,A WARNING

o To avoid injury from an accidental
start, make sure the switch is in
the OFF position and the plug
is disconnected
from the power
source outlet.
o Never operate this tool without the
riving knife in the correct position.
o Never operate this tool without
the blade guard in place for all
through sawing operations.
o This adjustment was made
at the factory, but it should
be rechecked and adjusted if
necessary.
1. Remove the table insert and raise
the blade to the maximum height
by turning the blade elevation
handwheel clockwise.
2. Remove the blade guard and antikickback pawl assembly.
3. Adjust the blade to the 0° vertical
position by unlocking the blade tilting
lock knob and turning the bevel tilting
handwheel counterclockwise, and
then lock into position.
4. To see if the blade (1) and riving
knife (2) are correctly aligned, lay a
combination square along the side
of the blade and against the riving
knife (making sure the square is
between the teeth of the blade).
5. Tilt the blade to the 45 ° position and
check the alignment again.
6. If the blade and riving knife are not
correctly aligned:
a. Loosen the locking knob (3) from
the mounting bracket (4).
b. Insert the washer (5) between the
riving knife and bracket (4) and

retighten the locking knob (3).

NOTE:
o Thewashers(1/4"1/2-3/32)
(5)are
notincludedwiththistablesaw.It
mustbepurchased
separately.
o Rivingknifethicknessis 0.09in.
o Themaximumradialdistance
betweentherivingknifeandthe
toothedrimofthesawbladeis 0.12
in- 0.31in.(3 mm- 8 mm)
o Thetipoftherivingknifeshallnot
belowerthan0.04in._ 0.2in.(1
mm_ 5 mm)fromthetoothpeak.
o Therivingknifeisthinnerthanthe
widthofthe kerfbyapproximately
1/64inoneachside.
8. Checktherivingknifeandblade
alignmentagainatboth0° and45°.
9. Addor removethewashersuntilthe
alignmentiscorrect.
10.Replace
thetableinsert,bladeguard
andanti-kickback
pawlassembly.
Fig.Q

installing the blade guard and anti=
kickback pawl assembly (Fig. R, S, T)
1. Make sure the blade is elevated to
its maximum height and the bevel is
set at 0 °. Make sure the bevel lock
handle is tight.
2. Take the anti-kickback pawl
assembly and lift up the locking
lever (1) located on top. (Fig R)
3. Place the front of assembly into slot
(2-Fig R) and push down making
sure the assembly is engaged in the
slots. There should be no movement
of the assembly. Push down on the
locking lever (1). (Fig S)

BLADEGUARDASSEMBLY
(FIG.B,S,T)
i_

o When installing the blade guard,
cover the blade teeth with a piece
of folded cardboard to protect
yourself from possible injury.
o Never operate this machine
without the blade guard in place
for all through sawing operations.

WARNING]

To avoid injury from an accidental
start, make sure the switch is in
the OFF position and the plug is
disconnected
from the power source
outlet.

Tighten

Take the blade guard assembly and
locate the black sliding locking knob
(4) on the back of assembly. (Fig. T)
Fig. T

5. Insert the blade guard assembly
onto the riving knife so that the pin
(5) engages into slot (6) completely.
(Fig T-I)
6. Slide the locking knob (4) up and
press the guard assembly down so
that the entire assembly is flat on
the riving knife. Release the locking
knob (4).
7. Make sure that the assembly is locked
in place both in front and back.
Fig. T-1

2. Loosen the blade lock handle do not
pull on handle just turn and move the
handwheel to 90 ° on the bevel scale.
3. Tighten the bevel lock handle.
4. Remove the anti-kickback pawl
assembly (3) by pressing the antikickback pawls lever (1). (Fig. R)
5. Removing the blade guard assembly
(7) by pulling out the locking pin (4).
(Fig. T-l)
AVOID KICKBACKS (FIG. U)
(Work thrown back towards you) by
keeping the blade sharp, the rip fence
parallel to the saw blade and by keeping
the riving knife, anti-kickback pawls and
guards in place, aligned and functioning.
Do not release work before passing it
completely beyond the saw blade. Do not
rip work that is twisted, warped or does
not have a straight edge to guide it along
the fence. Do not attempt to reverse out
of a cut with the blade running.

I,_

WARNING

Improper riving knife alignment can
cause "kickback" and serious injury.
Fig. U

Removing the blade guard and antikickback pawl assembly (Fig. R, T-l)

WARNING]

To avoid injury from an accidental
start, make sure the switch is in
the OFF position and the plug is
disconnected
from the power source
outlet.
1. With the blade elevation handwheel
raise the blade to the maximum
height:

Anti- kickback pawl

iNSTALLING TABLE SIDE
EXTENSIONS (FIG. V)
1. Identify the right hand table extension.
NOTE: For illustration purposes the
view in Fig. V looks "through" the
saw table to the under side of the
table. The right hand table extension
is the one with the measuring scale
visible from the front of the saw
when it is installed to the right hand
side of the saw table.

2. Unlockbothfrontandrearcam
lockinglevers(1)ontherighthand
sideofthesawbasebyflippingthe
leverover.
3. Insertthetableextensionmounting
tubes(2)intothetwomatching
holesinthecamleverassemblies.
NOTE:Makesurethefrontmounting
tubehasthemeasuring
scalevisible
fromthefrontofthesaw.
4. Slidethetableextensiontowardthe
tableuntilit restsagainstthesaw
table.
5. Lockbothcamlockingleversby
pushingthemintowardthecam
lockingleverassemblies.
6. Iftheextensionis notleveltothe
table,adjustbyinsertingthespacers
(CartonContentsS)betweenthe
extension
andthetubeit mounts
onto.Seepage35.
Fig. V

7. Make sure the screw (3) into the
matching hole (4) of the extension
mounting tube (2).
8. Install the left hand table extension
the same manner.
INSTALLING THE REAR TABLE
EXTENSION (FIG. W, X)
1. Insert the two rear table extension
tubes (2) into the rear table
extension (1).
NOTE: They must be inserted into
the back of the extension with the
bent end last so that the bar will

Snap two black plastic stops (3)
over the two rear table extension
tubes (2). Make sure the locating
pin in the black plastic stops fits into
the matching hole in the extension
tube. This will 'lock' the tube into the
extension. (Fig. W)
Fig. W
Bend End

3. Insert the rear table extension
tubes (2) into the two holes in the
rear of the saw table, and into the
extension tube brackets under the
table. Position the rear table support
so that the instruction labels are
facing up. (Fig. X)
4. Tighten one extension wing stop
screw (4) on the end of the left rear
table extension tubes (2). Verify that
the screw is fully inserted into the
corresponding hole in the extension
tube. (Fig. X)
Fig. X

ADJUSTING THE REAR TABLE
EXTENSION (FIG. X)
1. The rear table extension (1) should
be positioned as close as possible
to the rear of the table when ripping
short material.
2. The rear table extension (1) should
be fully extended when ripping longer
materials that require extra support.
iNSTALLING THE BATTERIES
THE LASER LINE (FIG. Y)

the left side of the body shell. The
bracket will snap into place.
Fig. Z
\

FOR
3
STORAGE (FIG. Z, AA, BB)
Rip fence, miter gauge (Fig. Z)
Storage brackets for the rip fence (2)
and miter gauge (3) are located on the
left side of the saw housing.
NOTE: Adjust the miter gauge to
45°-60 ° before putting away in storage.

[,_ WARNING]
Failure to unplug your saw could
result in accidental starting causing
possible serious personal injury.
1. Remove the locking screw (1) on the
cover of the battery compartment
with a Phillips screwdriver, and
open the battery compartment.
2. Install two "AAA" batteries.
3. Close the cover (2), and replace the
locking screw and tighten it securely.
4. Turn the switch (3) to the ON
position in order to activate the laser
cutting guide.
NOTE: See instructions on Adjusting
The Laser Line on page 33.
Fig. Y

Blade Wrench (Fig. AA)
Insert the blade wrench into the slot
(4) located to the back side of the saw
housing.
Fig. AA

1
3

4
Blade (Fig. BB)
1. Loosen and remove the knob (1) on
the left side of the saw housing.
2. Place extra blades (not included)
onto the arbor. Replace the knob
and tighten.
Fig. BB

INSTALLING

THE PUSH-STICK

STORAGE HOLDER (FIG. Z)
Attach the metal push-stick storage
bracket (1) into the provided slots on
27

MOVE THE TABLE SAW (FIG. CC)
1. Slide the table extension toward
the table until it rests against the
saw table and tighten the two camlocking levers.
2. Hold the table saw firmly, pull the
table saw toward you until the saw
is balanced on the wheels.
3. Move the saw to the desired
location for operation or store the
saw in a dry environment.
Fig. CC

4. if adjustment is needed to make the
fence parallel to the groove, do the
following:
o Loosen the two bolts (3) and lift
up on the handle (2).
o Hold the fence bracket (4) firmly
against the front of the saw table.
Move the fence until it is parallel
with the miter gauge groove.
o Push the handle down and
tighten both bolts.
5. if fence is loose when the handle is
in the locked (downward) position,
do the following:
o Move the handle (2) upward
and turn the adjusting nut (5)
clockwise until the rear clamp is
snug.
o Over-tightening the adjusting
bolts will cause the fence to come
out of alignment.

I,A WARNING
Failure to properly
cause "kickback"
RiP FENCE ADJUSTMENT (FIG. DD)
1. The fence (1) is moved by lifting
up on the handle (2) and sliding
the fence to the desired location.
Pushing down on the handle locks
the fence in position.
2. Position the fence on the right side
of the table and along the edge
miter gauge groove.
3. Lock the fence handle. The fence
should be parallel with the miter
gauge groove.

Fig. DD

I
align fence can
and serious

injury.

RiP FENCE iNDiCATOR
ADJUSTMENT (FIG. EE)
1. The rip fence indicator (6) points to
the measurement scale. The scale
shows the distance from the side of
the fence to nearest side of the blade.
2. Measure the actual distance with a
rule. if there is a difference between
the measurement and the indicator,
adjust the indicator (6).
3. Loosen the screw (7) and slide the
indicator to the correct measurement
on the scale. Tighten the screw and
remeasure with the rule.
Fig. EE

3. To change angles on the miter gauge,
loosen the lock handle (1) and rotate
the miter body to the desired angle
as indicated by the scale. Secure in
position by tightening the lock handle.
Fig. FF

ADJUSTING THE TABLE iNSERT
(FIG. GG)

WARNING]

To avoid serious injury, the table
insert (2) must be level with the
table, if the table insert is not flush
with the table, adjust the two bolts
(1) with a 4 mm hex wrench until it is
parallel with the table.

WARNING]

To avoid injury from an accidental
start, make sure the switch is in the
OFF position and the plug is not
connected to the power source outlet.
ADJUSTING THE MITER GAUGE
(FIG. FF)
1. Loosen the lock handle (1) to allow
the miter body (2) to rotate freely.
Position the miter body at 90 ° so the
positive detent secures its position.
Tighten the lock handle to hold the
miter body in position.
2. If the pointer (3) requires adjustment,
loosen the screw under the pointer
with a screwdriver. Adjust the pointer
to 90 ° on the scale, then firmly
tighten the adjustment screw.

NOTE: To raise the insert, turn the hex
screws counterclockwise, to lower the
insert, turn the hex screws clockwise.
Do not remove the insert, adjustments
need to be made with the insert in
place to get the proper level.
Fig. GG

ADJUSTING THE 90 ° AND 45 °
POSiTiVE STOPS (FIG. HH, ii)
Your saw has positive stops that will
quickly position the saw blade at 90 °
and 45 ° to the table. Make adjustments
only if necessary.
90 ° Stop
1. Disconnect the saw from the power
source.
2. Raise the blade to the maximum
elevation.
3. Loosen the blade bevel lock handle
and move the blade to the maximum
vertical position and tighten the
bevel lock handle.
4. Place a combination square on the
table and against the blade (1) to
determine if the blade is 90 ° to the
table. (Fig. HH)
5. If the blade is not 90 ° to the table,
loosen or tighten (depending on
whether you are increasing or
decreasing the degrees) the hex bolt
(3) with a 5 mm hex wrench until you
achieve 90 °. (Fig. II)
6. Loosen the bevel lock handle and
reset the blade at the maximum

45 ° Stop
1. Disconnect the saw from the power
source.
2. Raise the blade to the maximum
elevation.
3. Loosen the blade bevel lock handle
and move the blade to the maximum
bevel position (45°)and tighten the
bevel lock handle.
4. Place a combination square on the
table and against the blade (2) to
determine if the blade is 45 ° to the
table. (Fig. HH)
5. If the blade is not 45 ° to the table,
loosen or tighten (depending on
whether you are increasing or
decreasing the degrees) the hex bolt
(4) with a 5 mm hex wrench until you
achieve 45 °. (Fig. II)
6. The, loosen the bevel lock handle
and reset the blade at the maximum
bevel position (45°), then tighten the
bevel lock handle.
7. Check again to see if the blade is
45 ° to the table. If not, repeat step 5.

vertical position, then tighten the
bevel lock handle.
7. Check again to see if the blade is
90 ° to the table. If not, repeat step 5.
8. Lastly, check the bevel angle scale. If
the pointer does not read 90 °, loosen
the screw holding the pointer and
move the pointer so it is accurate at
0° and retighten the pointer screw.
Fig. HH

900

450

BLADE TiLT POINTER
1. When the blade is positioned at 90 °,
adjust the blade tilt pointer to read 0°
on the scale.
2. Loosen the holding screw, position the
pointer over 0 ° and tighten the screw.
NOTE: Make a trial cut on scrap wood
before making critical cuts. Measure for
exactness.

BLADEPARALLEL TO THE MITER
GAUGE GROOVE (FIG. JJ, KK)
I_

WARNING]

This adjustment was made at the
factory, but it should be rechecked
and adjusted if necessary.

WARNING]

To prevent personal injury:
o Always disconnect plug from the
power source when making any
adjustments.
o This adjustment must be correct
or accurate cuts can not be made.
Also inaccurate adjustment can
result in kickback and serious
personal injury.
1. Remove the safety switch key and
unplug the saw.
2. Remove the blade guard for this
procedure but reinstall and realign
after adjustment.
3. Raise the blade to the highest
position and set at the 0 ° angle
(90 ° straight up).
4. Select and mark, with a felt tip maker,
a blade tooth having a "right set" and
rotate the blade so the marked tooth
is 1/2 in. above the table.
5. Place the combination square base
(1) into the right side miter gauge
groove (2). (Fig. JJ)
6. Adjust the rule so it touches the front
marked tooth and lock ruler so it holds
its position in the square assembly.
7. Rotate the blade bringing the
marked tooth to the rear and about
1/2 in. above the blade.
8. Carefully slide the combination
square to the rear until the ruler
touches the marked tooth.

If the ruler touches the marked tooth
at the front and rear position, no
adjustment is needed at this time.
If not or the base of the rule is no
longer parallel with the edge of
the miter gauge groove, perform
adjustment procedure described in
next section.
Fig. JJ

iiiiiiiiiiiiii?iiiiiii!ii:iiii;iiiiii
j2
211

_aUI

ADDITIONAL

BLADE

ADJUSTMENTS

(FIG. KK)

NOTE: The adjusting mechanism
is located above the blade height
adjusting hand wheel under the
tabletop. If the front and rear
measurements are not the same.
if the blade is partial to right side:
1. Turn the left adjustment screw (2)
counterclockwise and adjust the
right side adjustment screw (3)
clockwise.
2. Remeasure, as described in steps 4
to 9 in the prior section.
3. When alignment is achieved, turn
the left adjustment screw (2) until it
touches the pivot rod (4).

If the bladeis partial

to left side:
1. Turn the right adjustment screw (3)

o Do not perform any adjustments
that are intended to increase the

counterclockwise and adjust the left
side adjustment screw (2) clockwise.
2. Remeasure, as described in steps 4
to 9 in the prior section.

power of the laser.
o When using the laser line, do not
point the laser beam at people and/
or reflecting surfaces. Even a lowintensity laser beam can cause eye
damage. Do not look directly into
the laser beam.
o If the Laser Line will not be used for

3. When alignment is achieved, turn
the right adjustment screw (3) until it
touches the pivot rod (4).

more than three months, remove
the batteries in order to avoid

Fig. KK

damage from possible leakage.
o The laser line does not include any
user-serviceable components. Do
not open the housing in an attempt
to repair it.
o Repairs should only be carried out at
a service center or by an authorized
service technician.

THE LASER LINE
This tool is equipped with the Laser
Trac®, which is a battery-powered

o NOTE: All the adjustments for the
operation of this machine have
been completed at the factory.
Due to normal wear and use, some
occasional readjustments may be

laser cutting guide. The laser line
allows the operator to anticipate the
path of the saw blade on the workpiece
before cutting begins.

necessary.
o CAUTiON-Use

i,_. WARNING]

of controls or

adjustments or performance of
procedures other than those
specified herein may result in
hazardous radiation exposure.
o CAUTiON-The use of optical
instruments with this product will
increase eye hazard.
o Do not attempt to repair or
disassemble the laser. If unqualified
persons attempt to repair this laser
product, serious injury may result.
Any repair required on this laser
product should be performed by
authorized service center personnel.

The laser beam is emitted when the
laser line is turned on. Do not stare
into the beam or view it directly
using optical instruments.
Do not
remove the warning label that is
affixed to the blade guard. Avoid
aiming the laser beam directly into
the eyes.
A laser beam is not a toy, and it
should not be used by children.
Misuse of this laser line can lead to
irreparable eye damage.
32

LASER RADIATION.
Do not stare into the beam or view it
directly using optical instruments.
Maximum output: < 1 mW
Wavelength: 630-670 nm
Complies with 21 CFR 1040.10 and
1040.11 Class II Laser Product.
Laser Warning Label:

3. If the laser line is not flush, loosen
the two set screws (1) using a small
flat bladed screwdriver that is not
provided, but do not remove them.
4. Use the 5 mm hex wrench that is not
provided, adjust the laser unit (2) until
the laser line is parallel with the blade.
NOTE: Be careful not to over-rotate
the laser unit. Do not rotate the laser
more than 1/8 of a turn in either
direction.

LASER
oo

MAX

OUTPUT

NOT

RAOIATION
STARE

< ImW

INTO

OlOOE

_and

5. Adjust the set screws (1) on the left

BEAM

LASER

630_670nrn
104011

_50

CLASS

LASER

PROOUCTj

ADJUSTING THE LASER LINE

or right side in order to shift the laser
line until it is flush with the right side
of the blade. Once proper alignment
has been achieved, tighten the set

(FIG. LL)

screw on the other side slowly, until
it touches the laser, in order to lock

the laser into position. Turn the laser
line off.

WARNING]

The laser beam is emitted when the
laser line is turned on. Do not stare
into beam or look directly at it using
optical instruments. Do not remove
the warning label that is affixed to the
blade guard. Do not direct the laser
into the eyes.

NOTE: If additional alignment is
required, use thin flat washers (not
provided) by placing them between the
riving knife and the mounting bracket.
Refer to the section of "Aligning the
riving knife" on page 23.

NOTE: All of the adjustments for the
operation of this machine have been
carried out at the factory. Occasional
readjustments may be necessary as a
result of normal wear and use.
1. Turn the laser line on. Place a
straight edge or ruler against the
right side of the blade.
2. Verify whether the laser line is flush
against the right side of the blade,
and against the straight edge or
ruler.

Fig. LL

BASIC SAW OPERATIONS
RAISE THE BLADE (FIG. MM)
To raise or lower the blade, turn the
blade elevation handwheel (1) to the
desired blade height, and then tighten
the bevel lock handle (2) to maintain
the desired blade angle.
Fig. MM

2. To turn the saw OFF, move the
switch downward.
3. To lock the switch in the OFF position,
grasp the end (or yellow part) of the
safety switch key (1), and pull it out.
4. With the safety removal key
removed, the switch will not operate.
5. if the safety removal key is removed
while the saw is running, it can be
turned OFF but cannot be restarted
without inserting the switch key (1).
Fig. NN

TiLTiNG THE BLADE
Two methods are available for tilting
the saw blade.
Rapid blade tilting:
Loosen the bevel lock handle (2), move
the handwheel (1) to the desired angle,
then tighten the bevel lock handle.
Fine adjustment blade tilting:
Loosen the bevel lock handle (2), push
in the handwheel (1) and at the same
time turn the handwheel (1) to tilt the
saw blade. When the saw blade is at
the desired angle, tighten the bevel
lock handle (2).
ON/OFF SWITCH (FIG. NN)
The ON / OFF switch has a safety
removal key. With the key removed from
the switch, unauthorized and hazardous
use by children and others is minimized.
1. To turn the saw ON, insert the safety
switch key (1) into the slot in the
switch (2). Move the switch upward
to the ON position.

OVERLOAD PROTECTION (FIG. NN)
This saw has an overload reset button
(3) that resets the motor after it shuts off
due to overloading or low voltage, if the
motor stops during operation, turn the
ON / OFF switch to the OFF position.
Wait about five minutes for the motor to
cool, the push the reset button (3) and
turn the switch to the ON position.

WARNING]

To avoid injury, the ON / OFF switch
should be in the OFF position and
the plug removed from the power
source while the cool down takes
place, to prevent accidental starting
when the reset button is pushed.
Overheating may be caused by
misaligned parts or a dull blade or
undersized extensing cord. inspect
your saw for proper setup before
using it again.

USINGTHE TABLE EXTENSION
(FIG. OO, PP)
If the table extension is not parallel
with the table, remove the bolts (1) and
position the extension leveling spacers
(2) between the table extension and
tube until it is parallel with the table,
then tighten the bolts.
NOTE: See page 14 for table of loose
parts ITEM: S
Fig. OO
J

1. Release the extension cam locking
levers (3).
2. Slide the extension (4) out until the
correct measurement is displayed
on the tube scale. The user sights
the scale off the edge of the table.
3. Tighten all extension cam locking
levers.
Fig. PP

CUTTING OPERATIONS
There are two basic types of cuts:
ripping and crosscutting. Ripping is
cutting along the length and the grain of
the workpiece. Crosscutting is cutting
either across the width or across the

grain of the workpiece. (It is not safe to
rip or crosscut by freehand). Ripping
requires the use of the rip fence, and
crosscutting requires the miter gauge.
NEVER USE THE TWO AT THE
SAME TIME.

WARNING]

Before using the saw each time,
check the following:
1. The blade is tightened to the arbor.
2. The bevel angle lock knob is
tightened.
3. If ripping, make sure the fence
is locked into position and
is parallel to the miter gauge
groove.
4. The blade guard is in place and
working properly.
5. Safety glasses are worn.
The failure to adhere to these
common safety rules, and those
printed in the front of this manual,
can greatly increase the likelihood
of injury.
RIPPING (FIG. QQ, RR)

WARNING

To prevent serious injury:
o Never use a miter gauge when
ripping.
o Never use more than one rip fence
during a single cut.
o Do not allow familiarity or frequent
use of your table saw to cause
careless mistakes. Remember
that even a careless fraction of
a second is enough to cause a
severe injury.
• Keep both hands away from the
blade and clear from the path of
the blade.

o The

workpiece must have a
straight edge against the fence
and must not be warped, twisted,
or bowed when ripping.

1. Remove the miter gauge and store it
in the "storage" compartment in the
base of the saw.
2. Secure the rip fence to the table.
3. Raise the blade so it is about 1/8 in.
higher than the top of the workpiece.
4. Place the workpiece flat on the table
and against the fence. Keep the
workpiece away from the blade.
5. Turn the saw ON and wait for the
blade to come to full speed.
6. Slowly feed the workpiece into the
blade by pushing forward only on the
workpiece section (1) that will pass
between the blade and the fence.
(Fig. QQ)
7. Keep your thumbs off the table top.
When both of your thumbs touch the
front edge of the table (2), finish the
cut with a push stick (3). To make an
additional push stick, use the pattern
on page 47. (Fig. QQ)

Fig. RR
4

8. Continue pushing the workpiece (6)
with the push stick (3-Fig. QQ) or
push block until it passes through
the blade guard and clears the rear
of the table. (Fig. RR)
9. Never pull the piece back when the
blade is turning. Turn the switch
OFF. When the blade completely
stops, you can then remove the
workpiece.

WARNING]

AVOID KICKBACK by pushing
forward on the section of the
workpiece that passes between the
blade and the fence. Never perform
any freehand operations.
Fig. QQ

2
;*

WARNING
i

When width or rip narrower than
2 in. the push stick cannot be
used because the blade guard will
interfere. Use the auxiliary fence (4)
and push block (5) as shown.

WARNING]

Never attempt to pull the workpiece
backwards during a cutting
operation. This will cause kickback
and serious injury to the user can
occur. When the blade completely
stops, raise the anti=kickback pawls
(7) on each side of the riving knife
and slide the workpiece out.

1
36

BEVEL RIPPING
This cut is the same as ripping except
the blade bevel angle is set to an angle
other than "0°''.

MAKE A FEATHERBOARD (FIG. SS)
Select a solid piece of lumber
approximately 3/4 in thick, 4 in wide and
18 in long. To make a featherboard, cut
one end of the lumber at 60 degrees,
then cut 8 in-long slots 1/4 in apart on
the angled end as shown in Fig. SS.

RIPPING SMALL PIECES
To avoid injury from the blade contact,
never make cuts narrower than 3/4 in.
wide.
1. It is unsafe to rip small pieces.
Instead, rip a larger piece to obtain
the size of the desired piece.
2. When a small width is to be ripped,
your hand cannot be safely put

Fig. SS
__]-

.=--

between the blade and the rip fence,

_J_

use push stick or push block to pass
the workpiece completely through
and past the blade.

-i-i,

•

FEATHERBOARD (FIG. SS, TT)
A featherboard is a device used to
help control the workpiece by guiding
it securely against the table or fence.
Featherboards are especially useful
when ripping small workpieces and for
completing non-through cuts. The end
is angled with a number of short kerfs
to give a friction hold on the workpiece
and locked in place on the table
with C-clamps. Test that it can resist
kickback.

personal

, ,

, , ,

i iiiii]f_flfN
_'l

Fig. TT

]

Place the featherboard against the
uncut portion of the workpiece to
avoid kickback that could cause
serious

J i
18in

USE A FEATHERBOARD (FIG. TT)
1. Lower the saw blade (1).
2. Position the rip fence (2) to the
desired adjustment and lock the rip
fence.
3. Place the workpiece (3) against the
fence and over the saw blade area.
4. Adjust the featherboard (4) to resist
the workpiece forward of the blade.
5. Attached the C-clamps (5) to secure
the featherboard to the edge of the
table.

HELPFUL DEVICES
In order to make some of cuts, it is
necessary to use the devices like, push
block, featherboard and auxiliary fence,
which you can make yourself. Here are
some templates for your reference.

[,_ WARNING

3
4

injury.
37

AUXILIARY FENCE (FIG. UU)
Making the base:
o Start with a piece of 3/8 in. plywood
at least 5-1/2 in. wide or wider and
21 in. long or longer.
o Cut the piece to shape and size
shown:
Making the side:
o Start with a piece of 3/4 in.
hardwood at least 1-3/4 in. wide or
wider and 21 in. long or longer.
o Cut the piece to shape and size
shown:
Putting it together:
o Fasten the pieces together with glue
and woodscrews.

WARNING]

Make sure the screw heads do
not stick out from the bottom of
the base, they must be flush or
recessed. The bottom must be flat
and smooth enough to rest on the
saw table without rocking.

MAKE A PUSH BLOCK (FIG. VV)
Making the base:
o Start with a 3/8 in. plywood at least
5-1/2 in. wide or wider and 12 in.
long or longer.
o Cut the piece to shape and size as
shown.
Making the handle:
o Start with a 3/4 in. hardwood at
least 5 in. wide or wider and 7 in.
long or longer.
o Cut the piece to shape and size as
shown.
Making the bracket:
o Start with a 3/8 in. wood at least 3/8
in. wide or wider and 2-1/2 in. long
or longer.
o Cut the piece to shape and size as
shown.
Putting it together:
o Fasten the base and handle
together with glue and woodscrews.

l_,

WARNING]

Make sure the screw heads do not
stick out from the bottom of the base,
they must be flush or recessed.

Fig. UU
3/8 in. thick plywood base

o Fasten the base and bracket
together with glue.

-'Tl

WARNING]

To avoid injury, do not use the screws
to fasten the base and bracket.
Fig. VV
The edge must be
parallel with

_I
l

PUSH BLOCK
Use for ripping operation when the
workpiece is too narrow to use a push
stick. Always use a push block for rip
widths less than 2 inches.

_1 II

=-I

TV I

I i _-_'2_°
i

CROSSCUTTING

(FIG. WW)

WARNING]

To prevent serious injury:
o Do not allow familiarity or frequent
use of your table saw to cause
careless mistakes. Remember
that even a careless fraction of
a second is enough to cause a
severe injury.
o Keep both hands away from the
blade and the path of the blade.
o Never attempt to pull the
workpiece backwards during a
cutting operation. This will cause
kickback and serious injury to the
user

can

occur.

1. Remove the rip fence and place
the miter gauge in the miter gauge
groove on the table.
2. Adjust the blade height so that it
is 1/8 in. higher than the top of the
workpiece.
3. Hold the workpiece firmly against
the miter gauge with the blade path
in line with the desired cut location.
Move the workpiece to a 1 in.
distance from the blade.
4. Start the saw and wait for the blade
(1) to come up to full speed. Never
stand directly in line of the saw blade
path, always stand to the side of the
blade that you are cutting on.
5. Keep the workpiece (2) against the
face of the miter gauge (3) and flat
against the table. Then slowly push
the workpiece through the blade.
6. Do not try to pull the workpiece back
with the blade turning. Turn the
switch OFF, and carefully slide the
workpiece out when the blade has
completely stopped.

I WARNING
i
Always position the larger surface
of the workpiece on the table
when crosscutting
and/or bevel
crosscutting
to avoid instability.
Fig. WW
3

2
\

_/1

USING THE WOOD FACING ON THE
MITER GAUGE (FIG. XX)
Slots are provided in the miter gauge
for attaching an auxiliary facing (1)
to make it easier to cut very long or
short pieces. Select a suitable piece of
smooth wood, drill two holes through
it and attach it to the miter gauge with
screws. Make sure the facing does not
interfere with the proper operation of
the saw blade guard. When cutting long
workpieces, you can make a simple
outfeed support by clamping a piece of
plywood to a sawhorse.
Fig. XX

BEVELCROSSCUTTING
(FIG.YY)
0°-45° BLADEBEVEL& 90° MITER
ANGLEThiscuttingoperationis the
same as crosscutting except the blade
is at a bevel angle other than 0°.

[_]_ WARNING]
Always work to the right side of the
blade during this type of cut. The
miter gauge must be in the right side
groove because the bevel angle may
cause the blade guard to interfere
with the cut if used on the left side
groove.
1. Lower the blade to the down position.
2. Adjust the blade (1) to the desired
angle, and tighten the blade bevel
lock knob.
3. Tighten the miter lock handle (2) at
90 °"
4. Hold workpiece (3) firmly against the
face of the miter gauge throughout
the cutting operation.
Fig. YY

COMPOUND MITER CROSSCUTTING
(FIG.ZZ)
00~45 ° BLADE BEVEL & 00~45 °
MITER ANGLE
This sawing operation combines a
miter angle with a bevel angle.

j,d_WARNING

]

Always work to the right side of the
blade during this type of cut. The
miter gauge must be in the right side

groove because the bevel angle may
cause the blade guard to interfere
with the cut if used on the left side
groove.
1. Set the miter gauge (3) to the
desired angle.
2. Place the miter gauge in the right
side groove of the table.
3. Set the blade (1) bevel to the
desired bevel angle and tighten the
blade bevel lock knob.
4. Hold workpiece (2) firmly against the
face of the miter gauge throughout
the cutting operation.
Fig. ZZ

MITERING (FIG. aa)
00~45° MITER ANGLE
This sawing operation is the same as
crosscutting except the miter gauge is
locked at an angle other than 90 °.
1. Set the blade (1) to 0° bevel angle
and tighten the blade bevel lock knob.
2. Set the miter gauge (3) at the
desired miter angle and lock in
position by tightening the miter
gauge locking handle.
3. Hold the workpiece (2) firmly
against the face of the miter gauge
throughout the cutting operation.
Fig. aa

USINGTHEWOOD

FACING ON THE

RiP FENCE (FIG. bb)

To avoid the risk of personal
injury. Always use push block,

When performing some special cutting
operations, you can add a wood facing
to either side of the rip fence (2).
1. Use a smooth straight 3/4 in. thick

auxiliary fence and featherboard
when making non-through cut.
1. Before starting the table saw, lower

wood board (1) that is as long as the
rip fence.
2. Attach the wood facing to the

the blade and riving knife assembly
to the down position.
2. Remove the blade guard assembly

fence with wood screws (3) (not
included) through the holes in the
fence. A wood fence should be used

and anti-kickback pawls assembly
for non-through cut.
3. Use the featherboard (1) with

when ripping material such as thin
paneling to prevent the material from
catching between the bottom of the
fence and the table.

C-clamps (3) to fasten the
workpiece securely.
4. Mount the auxiliary fence (4) with
C-clamps.

Fig. bb

5. Use the push block (2) to move the
workpiece.
NOTE:
o Mount the featherboard to table
as shown, so the leading edges of
featherboard will help workpiece
complete cutting.
Fig. cc

NON=THROUGH CUT (FIG. cc)
A non-through cut is used to cut
\

grooves and rabbets in the workpiece
without exposed the blade.

Non-through Cut

i,A WARNING]

o Only this type cut is made without
install the blade assembly, antikickback pawls assembly.
o To avoid injury from an accidental
start, make sure the switch is in
the OFF position and the plug
is disconnected
source outlet.

from the power
3

DADOCUTS(FIG.

dd, ee)

chippers as shown in the dado set's
instruction manual. Blade/chippers
must not exceed 1/2 in. total in
width.

1,,_, WARNING]
o Only Stackable dado blades can
be used on this saw.
o DO NOT use Adjustable or Wobble
type dadoes.
o The maximum
1/2 in.

Fig. dd
2

dado cut width is

1. Remove the table insert, saw blade,
anti-kickback pawl assembly, blade
guard assembly and riving knife
assembly for dado cuts ONLY.
Reinstall and realign blade guard
for all through-sawing operations.

7. Check the saw to ensure that the

Install a dado not exceeding 6 in. in
diameter and 1/2 in. in width

dado will not strike the housing,
insert, or motor when in operation.

2. Install the dado table insert making
sure that the rear of the insert is
flush with the table. If the dado insert

i.,_L.WARNING]
For your own safety, always replace
the blade, blade guard assembly,
anti=kickback pawl assembly,
riving knife assembly and table

is not flush with the table, adjust the
two bolts on the insert with a 4 mm
hex wrench until it is parallel with the
table.

insert when you finished
operation.

3. Instructions for operating the dado
is packed with the separately
purchased dado set.
4. The arbor (1) on this saw restricts
the maximum width of the cut to 1/2
in.

the dado

Fig. ee
Dado cut

5. It is not necessary to install the
outside flange (2) before threading
on the arbor nut (3) for the maximum
1/2 in. dado cuts. Make sure that the
arbor nut (3) is tight, and that at least
one thread of the arbor sticks out
past the nut.
6. Use only the correct number of
round outside blades and inside
_2

MAINTAINING YOUR TABLE SAW
GENERAL MAINTENANCE

{,,A WARNING]
For your own safety, turn the switch
OFF and remove the switch key.
Remove the plug from the power
source outlet before maintaining or
lubricating your saw.
1. Clean out all sawdust that has
accumulated inside the saw cabinet
and the motor.
2. Polish the saw table with an
automotive wax to keep it clean and to
make it easier to slide the workpiece.
3. Clean cutting blades with pitch and
gum remover.
4. A worn, cut, or damaged power cord
should be replaced immediately.

1. With the saw disconnected from the
power source, turn the saw upside
down and pull up and push down on
the motor unit.
2. Observe any movement of the
motor mounting mechanism.
3. Loosen or tighten the four hex
screws (1) by hex wrench for smooth
operation. Only 1/8 turn at a time.
NOTE: Do not adjust the screw
more than 1/2 turn as this may
damage the mechanism.
Fig. ff
1

{,,_, WARNING]
All electrical or mechanical repairs
should be attempted only by a
trained repair technician. Contact
customer service for assistance. Use
only identical replacement parts. Any
other parts may create a hazard.
5. Use liquid dishwashing detergent
and water to clean all plastic parts.
NOTE: Certain cleaning chemicals
can damage plastic parts.
6. Avoid use of cleaning chemicals or
solvents, ammonia and household
detergents containing ammonia.
BLADE RAISING AND TILTING
MECHANISM (FIG. ff, gg)
After every five hours of operation,
the blade raising mechanism and
tilting mechanism should be checked
for looseness, binding, or any other
abnormalities.

Place a small amount of dry
lubricant on the bevel gear (2). The
worm gear (3) must be kept clean
and free of sawdust, gum, pitch,
and other contaminants for smooth
operations.
Fig. gg

NOTE:If excessivelooseness
isobservedinanypartofthe
bladeraisingmechanism
ortilting
mechanism,
takethecompleteunitto a
ServiceCenter.
LUBRICATION
Allmotorbearingsarepermanently
lubricated
atthefactoryandrequireno
additionallubrication.
Onallmechanical
partsofyourtablesawwherea pivot
or threadedrodarepresent,lubricate
usinggraphiteorsilicone.Thesedry
lubricants
willnotholdsawdustas
wouldoilor grease.
REPLACING
THECARBON
BRUSHES
(FIG. hh, ii)
[_)_ WARNING]
Always disconnect the plug from the
power source before inspecting the
brushes.
The carbon brushes included with the
unit will last approximately 50 hours
of running time, or 10,000 ON/OFF
cycles. Replace both carbon brushes
when either has less than 1/4 in. length
of carbon remaining, or if the spring or
wire is damaged or burned.
1. Remove the blade guard, blade,
rip fence, miter gauge and stand
assembly from the table saw.
2. Lower the blade height to its
minimum setting. This will make the
brushes's location easier to access.
3. Place cardboard or an old blanket
on the floor to protect the saw table
surface.
4. Place the saw upside down on the
protective material.
5. Tilt the blade elevation/tilting
handwheel (1) to the 45 ° position.

6. Remove the black plastic cap (2)
from the side of the motor (3).
7. Carefully remove the spring-loaded
cap, and then pull out the brush and
replace.
8. Replace the other side.
9. The ears on the metal end of the
assembly go in the same hole
the carbon part fits into. Do not
overtighten the plastic cap.
10. Carefully set the saw in a upright
position on a clean level surface.
11 .Replace the blade guard, blade,
rip fence, miter gauge and stand
assembly to the table saw.
NOTE: To reinstall the same brushes,
first make sure the brushes go back in
the way they came out. This will avoid
a break-in period that reduces motor
performance and increases wear.
Fig. hh

Fig. ii
\\\\\
\\\

\
2

i,A WARNING

]

To avoid injury from accidental starting, always turn switch OFF and unplug
the tool before moving, replacing the blade or making adjustments.
PROBLEM

POSSIBLE CAUSES

CORRECTIVE ACTION

Saw will not
start.

1. Saw is not plugged in.
2. Fuse blown or circuit breaker
tripped.
3. Cord is damaged.
4. Debris in on/off switch

1. Plug in saw.
2. Replace fuse or reset circuit
breaker.
3. Replace power cord.
4. Remove switch from saw
and separate in half. Clean
any debris accumulated
within.

Does not make
accurate 45 °
and
90 ° rip cuts.

1. Positive stop not adjusted
correctly.
2. Tilt angle pointer not set
accurately.

1. Check blade with square
and adjust positive stop.
2. Check blade with square
and adjust to zero.

Material pinched 1. Rip fence not aligned with
blade when
blade.
ripping.
2. Warped wood, edge against
fence is not straight.

1. Check and adjust rip fence.
2. Select another piece of
wood.

Material binds
on riving knife.

1. Check and align riving knife
with blade.

Saw makes
unsatisfactory
cuts.

1. Riving knife not aligned
correctly with blade.
1. Dull blade.
2. Blade mounted backwards.
3. Gum or pitch on blade.
4. Incorrect blade for work being
done.
5. Gum or pitch on blade
causing erratic feed.

1. Replace blade.
2. Turn the blade around.
3. Remove blade and clean
with turpentine and coarse
steel wool.
4. Change the blade.
5. Clean table with turpentine
and steel wool.

1,_ WARNING

]

To avoid injury from accidental starting, always turn switch OFF and unplug
the tool before moving, replacing the blade or making adjustments.
Material kicked 1. Rip fence out of adjustment.
back from blade. 2. Riving knife not aligned with
blade.
3. Feeding stock without rip
fence.
4. Riving knife not in place.
5. Dull blade.
6. The operator letting go of
material before it is past saw
blade.
7. Miter angle lock knob is not
tight.
Blade does
1. Sawdust and dirt in elevation/
not raise or tilt
tilting mechanisms.
freely.

1. Align rip fence with miter
gauge slot.
2. Align riving knife with blade.
3. Install and use rip fence.
4. Install and use riving knife.
(with guard)
5. Replace blade.
6. Push material all the way
past saw blade before
releasing work.
7. Tighten knob.

Blade does

1. Replace with adequate size
cord.
2. Contact your electric
company.

not come up to
speed. Reset
trips too easily.
Machine
vibrates
excessively.

1. Extension cord too light or
too long.
2. Low house voltage.

1. Brush or blow out loose dust
and dirt.

1. Saw not mounted securely to 1. Tighten all mounting
workbench.
hardware.
2. Reposition on flat level
2. Bench on uneven floor.
3. Damaged saw blade.
surface.
3. Replace blade.

Does not make 1. Miter gauge out of
accurate 45 ° and
adjustment.
90 ° crosscuts.

1. Adjust miter gauge.

PUSH STICK CONSTRUCTION
®
®
®

Use good quality plywood or solid wood
Use 1/2 in. or 3/4 in. material
Push stick MUST be thinner than the width of
material being cut

/
/
/
/
/

/
Drill Hole
For Hanging

Notch To
Prevent Hand
/
/"

From Slipping

/
/
/
/

/
/
/"
/
/
/
/
/
/
/
/

Cut Here To

//900
200 /

Push 1/2 in. Wood

Cut Here To
Push 3/4 in. Wood

10 in. TABLE SAW

WARNING

MODEL NO. 137.218070

]

When servicing use only CRAFTSMAN replacement parts. Use of any other
parts many create a HAZARD or cause product damage. Any attempt to
repair or replace electrical parts on this Table Saw may create a HAZARD
unless repair is done by a qualified service technician. Repair service is
available at your nearest Sears Service Center.
PARTS LiST FOR TABLE SAW SCHEMATIC A
I.D,

Description

Size

0B6V

CLAMP

M6_1.0

2FTB

EXTENSION WiNG

0J5L

FLAT WASHER

cp5_10-0 3

2GYV

SLiDiNG BASE ASS'Y

0J6V

FLAT WASHER

3/163/8

2JHQ

SLiDiNG BASE ASS'Y

0J76

FLAT WASHER

1/4"3/4-1/16

2NE3

NEEDLE POINTER

0J78

FLAT WASHER

1/4_1/2-3/32

2NE4

NEEDLE POINTER

0JAF

EXTERNAL TOOTH LOCK WASHER

2NRD

EXTENSION WiNG ROD

0JVY

HEX SOC. HD. CAP BOLT

M6_1.0-16

2NRE

EXTENSION WiNG ROD

0K6Y

CR. RE. TRUSS HD. SCREW

M4_0.7-10

2NRF

EXTENSION WiNG ROD

0K7E

CR. RE. ROUND WASHER HD. SCREW

M5_0.8-6

2NRG

EXTENSION WiNG ROD

0K9T

HEX HD. TAPPING

SCREW

M5_16-16

2NSC

REAR OUT-FEED SUPPORT ROD

0K9U

HEX, HD. TAPPING

SCREW

M5_16-25

2RV8

REAR OUT-FEED SUPPORT

0KAE

CR. RE. PAN HD. TAPPING

SCREW

M5_0.8-10

2RVE

iNSERT

0KBA

CR. RE. PAN HD. TAPPING

SCREW

M5_16-12

2RVP

BETPLATE

0KBQ

CR. RE. PAN HD. TAPPING

SCREW

M5_16-10

2RVQ

RiViNG

0KCX

CR. RE. PAN HD PLAIN WASHER
TAPPING SCREW

M5_0.8_10

2RVX

BLADE GUARD

0KCY

CR. RE. PAN HD PLAIN WASHER
TAPPING SCREW

M5_0.8_12

2RW4

NEEDLE POINTER

0SZY

SLiDiNG

BASE ASS'Y

2RW6

BETPLATE

0SZZ

SLiDiNG

BASE ASS'Y

2RWG

EXTENTION WiNG

10K5

HEX SOC. HD CAP BOLT

2RXQ

SPACER

2RXS

RIP FENCE ASS'Y

2SUU

SCALE(RIGHT)

2SUV

SCALE (LEFT)

HANDLE

10LB

BOLT CLAMP

10LE

CR. RE. TRUSS HD. ROUND
SCREW

212M

LEAD WIRE ASS'Y

QTY I.D.

0022

M5_0.8-8

NECK

M5_0.8-16

M6_1.0-25

Description

Size
(LEFT)

#AW

QTY
1

#23

KNIFE

1
(RIGHT)

#AW

25AP

HEX, SOC. HD, CAP BOLT

2SUW

SCALE (LEFT)

26LU

WARNING

LABEL

2SUX

SCALE(RIGHT)

275F

LOCATION

SEAT

2SUY

SCALE

28N2

AAA

2SV2

WARNING

290M

CAUTION

2SUS

INSTRUCTIONS MANUAL

29R2

WARNING

2T6B

HARDWARE

29WT

LASER SETASS'Y

2T6C

BLADE GUARD ASS'Y

2AZ7

CR. RE PAN HD PLAIN WASHER
TAPPING SCREW

M2.6_24_8

2T6D

ANTPKICKBACK

2DUB

CR. RE, ROUND WASHER HD. SCREW

M5_0.8-12

2T6F

HANDLE

2EUO

TiLTiNG SCALE

2T87

LABEL(LASER)-LEFT

2EVJ

MITER GAUGE

2TB9

LABEL(LASER)-RIGHT

2FSV

TABLE

BATTERY
LABEL
LABEL

ASS'Y
#AW

1
48

LABEL

BAG ASS'Y

PAWL ASS'Y

0
I

o
5'

2TB9

rm
>

]

10K54

OKCX4

02J A F

12M
_0KBQ

o
2SUS

m
r-

o
'-4

co
o
.,4
o

10 in. TABLE SAW

MODEL NO. 137.218070

PARTS LiST FOR SAW SCHEMATIC
I.D.

Description

0901

BUSH

08VH

CORD

08VN
090Q

Size

QTY I.D.

Size

Description

QTY

OKSM

STRAIN RELIEF

OKTH

STRAIN RELIEF

POINTER BRACKET

OKUX

TERMINAL

PLUNGER HOUSING

OKWU

LEAD WIRE ASS'Y

09JK

WRENCH

OLSL

CIRCUIT BREAKER SWITCH

0AW8

SEGMENT GEAR

OLVJ

SWITCH KEY

0B3R

WRENCH

OLWG

ON/OFF

0B9P

CLAMP

OSGC

HANDLE BAR

0BA1

COMPRESSION

10J9

CAP HD. SQ. NECK BOLT

0BA4

SPACER

2149

KNOB

0BA9

SPACER

23PP

BLADE

0BAC

SET NUT

26E8

FLAT WASHER

0BAE

ARBOR COLLAR

275R

LOCATION

0BPA

LOCK KNOB

27JR

HEX. SOC. SET SCREW

0J3P

HEX. WRENCH

29R6

STICKER

0J4F

FLAT WASHER

cp8_16-2.5

2A47

0J5C

FLAT WASHER

@13.8_10-2.85

0J6K

FLAT WASHER

cp6_30-4

0J6T

FLAT WASHER

0J70

FLAT WASHER

0J74

FLAT WASHER

0J77

CLAMP

SPRING

ROCKER SWITCH ASSEMBLY

M6_1.0-40

cp5_9.5-1.2

SEAT
M5_0.8-6

HEX. HD. SCREW AND WASHER

M6_1.0-12

2A48

HEX. HD. SCREW AND WASHER

M5_0.8 -16

2BUY

BODY SHELL

3/16_3/4-1/16

2CBS

PUSH BLOCK

1/4_3/4-7/64

2EJX

POWER CABLE ASS'Y

1/4_5/8-3/32

2RVH

WHEEL

FLAT WASHER

1/4_9/16-3/64

2RVJ

CLAMPER

0J8D

FLAT WASHER

3/8_3/4-5/64

2RVK

BODY

0JAE

EXTERNAL TOOTH LOCK WASHER

2RVM

GEAR

0JAF

EXTERNAL TOOTH LOCK WASHER

2RVN

SPLITTERBRACKET

0JB2

WAVE WASHER

WW-12

2RVR

GUIDE CLAMP

0JC9

SPRING PIN

2RVW

RETAINING CLIP

0JD1

SPRING PIN

2RW3

RETAINING CLIP

0JPJ

HEX, HD. BOLT

M6_1.0-40

2RW5

NEEDLE POINTER

0JZY

HEX, SOC. TRUSS HD. SCREW

M6_1.0-12

2RW8

SHIM

0KOY

HEX, HD. SCREW AND

WASHER

M6_1.0-20

2RWA

ANGLE

0K1G

HEX. HD. SCREW AND

WASHER

M6_1.0-12

2RWC

HEIGHT REGULATING

0K45

CR. RE. PAN HD. SCREW &
WASHER

M6_1,0-12

2S15

MOTOR ASS'Y

0K8C

CR. RE. COUNT
SCREW

M4_18_10

2SEO

ANCHOR

0K9T

HEX. HD. TAPPING

SCREW

M5_16-16

2SE9

SAFETY PLATE

0K9U

HEX. HD. TAPPING

SCREW

0KA4

CR. RE. PAN HD. TAPPING

0KCA

HD. TAPPING

BRACKET

ROD
BOLT

PLATE

M5_16-25

2SJU

SPACER

SCREW M4_16-16

2SUZ

WARNING

CR. RE. TRUSS HD. TAPPING
SCREW

M5_12-12

2SV1

LABEL

0KDK

CR. RE. PAN HD. SCREW

M5_0.8-16

2SV3

LABEL

0KF7

CR. RE. PAN HD. SCREW

M4_0.7-12

2T69

SPECIAL BOLT

0KJ7

CAP HD. SQ.NECK

M8_1.25-16

2T6E

CLAMP ASS'Y

0KMY

HEX. NUT

M8_1.25

2TD0

COLLAR

0KNE

HEX. NUT

M6_1.0 T=5

2TDD

WORM

0KQW

LOCK NUT

M5_0.8 T=5

2TDL

FLAT WASHER

0KQX

NUT

M6_1.0 T=6

2TDS

SWITCH BOX ASS'Y

0KQY

LOCK NUT

M8_1.25

BOLT

T=6.5

T=8

LABEL

OJ6K
/

OK J7

OBPA

\
09018D_OJ

2TDL

"_ _O_o_v_
OJAF

26E8

29R6
)J4F

2RVR4

2815

o
o
m
ff-

08VH/_
OKA4_
OB3R
_0KUX

0KTH

2
"q

0KWU

2TDS_
Co
O
_4
O

10 in. TABLE SAW

MODEL NO, 137.218070

PARTS LiST FOR MOTOR
Description

OHX9

NEEDLE BEARLNG

OJX3

HEX. SOC. SETSCREW

M5"0.8-8

OK3Y

CR. RE. PAN HD. SCREW & WASHER

M5"0.8-50

OKTA

STRAIN RELIEF

OQM2

BRUSH HOLDER ASS'Y

@27"26,5

OQQT

BRUSH ASS'Y

OQR0

BRUSH COVER

110A

CR. RE. PAN HD. TAPPING

2DW9

WAVE WASHER

2RPP

FLOW GULDE

2RPS

MOTOR

2RRD

CUTTER SHAFT ASS'Y

2RT8

ARMATURE ASS'Y

2RUY

BALL BEARLNG

2RWF

BRACKET

2RWS

CR. RE. COUNTER-SUNK

2RXC

LABEL

2SDK

BALL BEARLNG

2TDF

FIELD ASS'Y

zf
J

J
J
%..
\

Size

QTY

I.D.

2
2
SCREW & WASHER

M5"12-55

COVER

6002ZLU
1
HEAD SCREW

M5"0.8-10

2
1

608ZZ

1
1

10 in. TABLE SAW

MODEL NO. 137.218070

PARTS LiST FOR STAND
Description

Size

I.D.

Description

0J4F

FLAT WASHER

@8_16-2.5

2SB2

PLUNGER HOUSING

0JPS

HEX. HD. BOLT

M8_1.25-45

2SB3

CLAMP

0KJ7

CAP HD. SQ. FLECK BOLT

M8_1.25-16

2SBX

HANDLE

0KHX

CAP HD. SQ. NECK BOLT

M5_0.8-10

2SE1

ROLLING

0KQW

LOCK NUT

M5_0.8 T=5

2SE2

DUST BAG

0KQY

LOCK NUT

M8_1.25 T=8

2SK6

LOCKING

0KRR

SERRATED TOOTHED HEXAGON
FLANGE NUT

M8 _1.25 T=7.5

2SK7

ROLLING

0Z1G

CAP HD. SQ. NECK BOLT

M8_1.25-12

2SK8

HARDWARE

22FZ

CAP HD. SQ. NECK BOLT

M8_1.25-45

2SK9

STAND ASS'Y

2A92

SPRING PIN

2SKC

SPRING PIN

2BUD

BOTTOM SUPPORT BRACKET

# AW

2SV0

TRADE-MARK

2BUE

BOTTOM SUPPORT BRACKET

# AW

2SXP

UPPER SUPPORT

# AW

2BV2

CUSHION

2SXQ

UPPER SUPPORT

# AW

2RVD

MAIN

# AW

2T5A

BOTTOM SUPPORT BRACKET

# AW

2RW1

BRACKET

# AW

2TDW

CAUTION

2RWE

DUST BAG HOOK

LEG BRACKET

QTY

Size

QTY

I.D,

HANDLE

WHEEL

HANDLE ASS'Y

WHEEL ASS'Y

BAG ASS'Y

LABEL

_2SE2

2RVD4

Your Home
For expert troubleshooting and home solutions advice:

www.managemyhome.com

For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.

1-800-4-MY-HOME ® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)

www.sears,oom www.sears,ca
Our Home

For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest

Sears Parts & Repair Service Center

1-800-488-1222 (u.s.A.)

1-800-469-4663

www,sears.com

TO purchase a protection
1-800-827-6655

agreement

(U.S.A.)

Para pedir servicio de reparacion
a domicitio, y para ordenar piezas:

on a product serviced by Sears:
1-800-361-6665

(1-800-,33-6937/

(1- 888- 784- 6427)

Trademark
/ TM Trademark
/ s M Service
Mark of Sears
Brands,
® Marca
Registrada
/ TM Marca de F&brica
/ sM Marca de Servicio
de Sears
MO
MD
Marque
de commerce
/
Marque
deposee
de Sears
Brands,
LLC

(Canada)

Au Canada pour service en frangais:
1 800 LE FOYER Mc

1-888-SU-HOGAR®

® Registered

!_!i

(Canada)

www,sears,ca

www. sea rs. ca

LLC
Brands,

LLC
© Sears

Brands,

LLC

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 56
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 4, 0, 0, 13
Create Date                     : Fri Nov 07 04:19:13 2008
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 137218070 User Manual TABLE SAW/STAND Manuals And Guides L0810542

CRAFTSMAN Saw Table Manual L0810542 CRAFTSMAN Saw Table Owner's Manual, CRAFTSMAN Saw Table installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation