Craftsman 137229170 User Manual 17 DRILL PRESS Manuals And Guides L0308059

CRAFTSMAN Drill Press Manual L0308059 CRAFTSMAN Drill Press Owner's Manual, CRAFTSMAN Drill Press installation guides

User Manual: Craftsman 137229170 137229170 CRAFTSMAN 17 DRILL PRESS - Manuals and Guides View the owners manual for your CRAFTSMAN 17 DRILL PRESS #137229170. Home:Tool Parts:Craftsman Parts:Craftsman 17 DRILL PRESS Manual

Open the PDF directly: View PDF .
Page Count: 25

Download
Open PDF In Browser	View PDF

Operator's Manual

CRAFTSMAN"
1-1/2 HP (Maximum Developed)
16 Speeds (200-3630 R.P.M.)
5/8 Inch Chuck

17-INCH DRILL PRESS
Model No.
137.229171

CAUTION:
Before using this Drill Press,
read this manual and follow
all its Safety Rules and
Operating Instructions

1400443-1682
I Customer
Help

Seam, Roebuck

•
•
•
•
•
•

Safety Instructions
Installation
Operation
Maintenance
Parts List
Espa5ol

Line

and Co., Hoffman Estates, IL 601_Td_Slalec,d

Visit our Craftsman webslte: www.sears.com/craftsman
Pa_ No. 137229171001

SECTION

PAGE

Warranty
...............................................................................................................
Product
Specifications
.............................................................................................
Safety Instructions
..................................................................................................
Accessories
and Attachments
..................................................................................
Carton Contents
......................................................................................................
Know Your Drill Press ..............................................................................................

2
2
3
6
6
8

Glossary
of Terms .......... . ........................................................................................
Assembly
and Adjustment
........................................................................................
Operation
..........................
:....................................................................................
Maintenance
...........................................................................................................

9
10
15
20

Troubleshooting
Guide ............................................................................................
Parts ......................................................................................................................

21
22

Espa[_ol

..................................................................................................................

FULL ONE YEAR WARRANTY
If this Driss Press fails due to a defect in material or workmanship
Sears will at its option repair or replace it free of charge•

within one year of date of purchase,

Return this Drill Press to a Sears Service Center for repair, or to place of purchase
This warranty gives you specific
state to state.
Sears, Roebuck

for replacement.

legal rights, and you may also have other rights which may vary from

and Co., Dept. 817 WA, Hoffrnan

Estates,

IL 60179

Some dust created by power sanding, sawing, grinding, drilling and other construction
activities contains
chemicals known to the state of California to cause cancer, birth defects or other reproductive
harm. Some
examples of these chemicals
are:
Lead from lead-based
paints
; Crystalline
silica from bricks, cement and other masonry products
•
• Arsenic and chromium from chemicallytreated
lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals,
work in a well-ventilated
area and work with approved safety equipmentsuch
as
dust masks that are specially designed to filter out microscopic
particles.

Chuck Si:_e ............................
Speed ...................................
Motor ....................................
Horsepower ...........................
Developed)
Built-in Light .........................
Table Size ............................
Table Tilt ...............................
Spindle Travel ........................
Throat .................................
Base Size .............................
Height ..................................

5/8"
16 (200 - 3,600 RPM)
120V, 60 Hz, 12 Amps
1-1/2 HP (Max.
60 Watt (Maximum)
(Bulb not included)
14-1/4" x 14-1/4"
45 ° Right or Left
3-1/4"
8-1/2"
11" x 20-3/8"
64-7/8"

_Tirl.J ;] _[[_e]
To avoid electdcal hazards, fire hazards, or damage to
the tool. use proper circuit protection
Your drill press is wired at the factory for 120V operation.
Connect to a 120V, 15 AMP branch circuit and use a 15
AMP time delay fuse or circuit breaker. To avoid shock or
fire, replace power cord immediately if it is worn, cut or
damaged in any way.

GENERAL SAFETY INSTRUCTIONS
BEFORE USING THE DRILL PRESS
Safety is a combination of common sense, staying alert
and knowing how to use your drill press.

14.REMOVE

ADJUSTING KEYS AND WRENCHES,
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning "ON"

15. NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN THE POWER "OFF". Don't leave the.tool until
it comes to a complete stop.

To avoid mistakes that could cause serious injury, do not
plug the drill press in until you have read and understood
the following:

16. NEVER STAND ON TOOL. Serious injurycould occur
if the tool is tipped or if the cuttingtool is unintentionally
contacted.

READ and become familiar with this entire instruction
manual. LEARN the tool'sapplications,limitations,and
possible hazards.

17. DON'T OVERREACH. Keep proper footing and
balance at all times.

KEEP GUARDS IN PLACE and in workingorder.

DON'T USE IN A DANGEROUS ENVIRONMENT.
Don't use power tools in damp or wet locations, or
expose them to rein. Keep work area well lighted.

DO NOT use power tools in the presence of flammable
liquids or gases.

KEEP WORK AREA CLEAN. Cluttered areas and
benches inviteaccidents.

KEEP CHILDREN AWAY.All visitorsshouldbe kept at
a safe distance from the work area.

DON'T FORCE THE TOOL. it will do the job better
and safer at the rate for which it was designed.

18. MAINTAIN TOOLS WITH CARE. Keep tools sharp
and clean for best and safest performance. Follow
instructionsfor lubricating and changing accessories
19. CHECK FOR DAMAGED PARTS. Beforefurther use of
the tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
propedy and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting and any other conditions
that may affect its operation.A guard or other part that
is damaged should be propedy repaired or replaced.
20. MAKE WORKSHOP KID PROOF with padlocks, master
switches, or by removing starter keys.

USETHE RIGHTTOOL. Don't force tool or the
attachment to do a job for which it was not designed.

21. DO NOT operate the tool if you are under the influence
of any drugs, alcohol or medication that could affect
your ability to use the tool properly.

WEAR PROPER APPAREL DO NOT wear loose
clothing; gloves, neckties, rings, bracelets, or other
jewelry which may get caught in moving parts.
Nonslip footwear is recommended. Wear protective
hair covering to contain long hair.

22. Dust generated from certain materials can be
hazardous to your health. Always operate the drill
press in a well-ventilated area and provide for proper
dust removal. Use dust collection systems whenever
possible.

10. WEAR A FACE MASK OR DUST MASK.
Drilling operation produces dust.
11. DISCONNECTTOOLS before servicing, and when
changing accessories, such as blades, bits, cutters,
and the like.
12. REDUCETHE RISK OF UNINTENTIONAL STARTING.
Make sure the switch is in "OFF" position before
plugging in.
13. USE RECOMMENDED ACCESSORIES. Consult the
owner's manual for the recommended accessories.
The use of improper accessories may cause risk of
injury to persons.

23. ALWAYS WEAR EYE
PROTECTION. Any drill press
can throw foreign objects into
the eyes which could cause
permanent eye damage.
ALWAYS wear Safety Goggles
(not glasses) that comply with
ANSI safety standard Z87.1. Everyday eyeglasses
have only impact-resistant lenses. They ARE NOT
safety glasses. Safety Goggles are available at Sears.
NOTE: Glasses or goggles not in compliance with
ANSI Z87.1 could seriously hurt you when they break.

SAVE THESE INSTRUCTIONS

SPECIFIC SAFETY INSTRUCTIONS
FOR THE DRILL PRESS

For your own safety, do not try to usa your drillpress
or plug it in until it is completely assembled and installed
according to the instructions, and until you have read and
understood this instruction manual:
1,

YOUR DRILL PRESS MUST BE BOLTED securely
to a workbench. In addition, if there is any tendency
for your drill press to move during certain operations,
bolt the workbench to the floor.
THIS DRILL PRESS is intended for use in dry
conditions, indoor use only.
WEAR EYE PROTECTION. USE face or dust mask
along with safety goggles if drilling operation is dusty.
USE ear protectors, especiallydudng extended periods
of operation.

DO NOT wear gloves, neckties, or loose clothing.

DO NOT try to drill material too small to be securely
held.

ALWAYS keep hands out of the path of a drill bit.
Avoid awkward hand positions where a sudden slip
could cause your hand to move into the ddll bit,
DO NOT install or use any drill bit that exceeds
175 mm (7") in length or extends 150 mm (6") below
the chuck jaws. They can suddenly bend outward or
break.

14. SECURE WORK. Use clamps or a vise to hold the
work when practical. It's safer than using your hand
and it frees both hands to operate tool.
15. WHEN using a drill press vise, always fasten to the
table.
16. MAKE SURE all clamps and locks are firmly
tightened before drilling.
17. SECURELY LOCK THE HEAD and table support to
the column, and the table to the table support before
operating the drill press.
18. NEVER turn your drill press on before cleadng the
table of all objects (tools, scraps of wood, etc.)
19. BEFORE STARTING the operation, jog the motor
switch to make sure the ddll bit does not wobble or
vibrate.
20. LET THE SPINDLE REACH FULL SPEED before
starting to ddll. If your drill press makes an unfamiliar
noise or if it vibrates excessively, stop immediately,
turn the drillpress off and unplug.Do not restart until
the problem is corrected.
21. DO NOT perform layout assembly or set up work on
the table while the drill press is in operation.
22. USE RECOMMENDED SPEED for drill accessory and
wotkpiecematerial. SEE INSTRUCTIONS that come
with the accessory.

DO NOT USE wire wheels, router bits, shaper cutters,
circle (fly) cutters, or rotary planers on this ddll press.

23. WHEN DRILLING large diameter holes, clamp the
workpiece firmly to the table. Otherwise, the bit may
grab and spin the workpiece at high speed. DO NOT
USE fly cutters or multiple-part hole cutters, as they
can come apart or become unbalanced in use.

WHEN cutting a large piece of material make sure it
is fully SUldportedat the table height.

24. MAKE SURE the spindle has come to a complete
stop before touching the workpiece.

10. DO NOT perform any operation freehand. ALWAYS
hold the workpiece firmly against the table so it will
not rock or twist. Use clamps or a vise for unstable
workpieces.

25. TO AVOID INJURY from accidental starting, always
tum the switch "OFF" and unplugthe dnll press before
installing or removing any accessory or attachment
or making any adjustment.

1 f. MAKE SURE there are no nails or foreign objects in
the part of the workpiece to be drilled.

26. KEEP GUARDS IN PLACE and in working order.

12. CLAMPWORKPIECE OR BRACE against the I_t
side of the column to prevent rotation, ff it is too short
or the table is tilted, clamp solidly to the table and
use the fence provided.

27. USE ONLY SELF-EJECTING TYPE CHUCK.KEY as
provided with the drill press.

13. IFTHE WORKPIECE overhangs the table such that
it will fall or tip if not held, clamp it to the table or
provide auxiliary support.

SAVE THESE INSTRUCTIONS

GROUNDING

INSTRUCTIONS

IN THE EVENT OF A MALFUNCTION OR BREAKDOWN,
grounding provides a path of least resistance for electric
current and reduces the risk of electric shock. This tool
is equipped with an electdc cord that has an equipment.
grounding conductor and a grounding plug. The plug
MUST be plugged into a matching receptacle that is
properly installed and grounded in accordance with ALL
local codes and ordinances.
DO NOT MODIFYTHE PLUG PROVIDED. If it will not fit the
receptacle, have the proper receptacle installed by a
qualified electrician.
IMPROPER CONNECTION of the equipment grounding
conductor can result in risk of electric shock. The
conductor with the green insulation(with or without yellow
stripes) is the equipment grounding conductor. If repair
or replacement of the electric cord or plug is necessary,
DO NOT connect the equipment groundingconductor to
a live terminal.
CHECK with a qualified electrician or service personnel it
you do not completelyunderstandthe groundinginstructions,
or if you are not sure the tool is properly grounded.

This tool is intended for use on a cimuit that has a
receptacle like the one illustrated in FIGURE A
RGURE A shows a 3-prong electrical plug and receptacle
that has a grounding conductor. If a properly grounded
receptacle is not available, an adapter (FIGURE B) can
be used to temporarily connect this plug to a 2-contact
ungrounded receptacle. The adapter (FIGURE B) has a
rigid lug extending from it that MUST be connected to a
permanent earth ground, such as a properly grounded
receptacle box. THE TEMPORARY ADAPTER SHOULD
BE USED ONLY UNTIL A PROPERLY GROUNDED
OUTLET CAN BE INSTALLED BY A QUALIFIED
ELECTRICIAN. The Canadian Electrical Code prohibits
the usa of adapters.
CAUTION: In all cases, make certain the receptacle in
question is propedy grounded. If you are not sure have a
certified electriciancheck the receptacle.

This ddll press is for indoor use only. Do not expose to
rein or use in damp locations.
Fig. A
3-Prong Plug

USE ONLY 3-WIRE EXTENSION CORDS THAT HAVE
3-PRONG GROUNDING PLUGS AND 3-POLE
RECEPTACLES THAT ACCEPT THE TOOL'S PLUG.
REPAIR OR REPLACE DAMAGED OR WORN CORD
IMMEDIATELY.

GUIDELINES

FOR EXTENSION

CORDS

Prong
Properly Grounded
3-Prong Receptacle

Fig. B
Grounding Lug I_

Make sure your extension cord is in good condition.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will drew. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating.The table below shows
the correct size to usa according to cord length and
nameplate ampere rating.If in doubt, use the next heavier
gauge. The smaller the gauge number,the heavierfile cord.
Be sure your extension cord is properly wired and in
good condition. Always replace a damaged extension
cord or have it repaired by a qualified person before
using it. Protect your extension cords from sharp objects,
excessive heat and damp or wet areas.

._
//f_'-'_

_:_
_1 .._
_"'-¢"___1"_v

If
1 _'_L
_---_\
_
Adapter

is Connected toa

Known Ground
I["" 2-Prong
Receptacle

This tool must be grounded while in use to protect the
operator from electrical shock.

(whenusing120 voltso_y)

Use a separate electrical circuit for your tools.This cimuit
must not be less than #12 wire and should be protected
with a 15 Amp time lag fuse. Before connectingthe motor
to the power line, make sure the switch is in the "OFF"
position and the electdc current is rated the same as the
current stamped on the motor nameplate. Running at a
lower voltage will damage the motor.

Ampere R_Ing

Totallengthofcordln

m(_e _man

noqmore than

25'

50'

100'

150'

0
6
10
12

6
10
12
16

Notrecomrnended

SAVE THESE INSTRUCTIONS

feet

AVAILABLE ACCESSORIES

Use only accessories recommended for this drill press.
Follow instructions that accompany accessories. Use of
improper accessories may cause hazards.
Visit your Sears Hardware Department or see the Sears
Power and Hand Tool Catalog for the following
accessories:
•
•

Drill bits
Hold-Down and Guide
Drill Press Vises

•

Clamping Kit

UNPACKING AND CHECKING
CONTENTS

If any part is missing or damaged, do not plug the drill
press in until the missing or damaged part is replaced,
and assembly is complete.
Carefully unpack the drill press and all its parts, and
compare against the list below.
To protect the drill press from moisture, a protective
coating has been applied to the machined surfaces.
Remove this coating with a soft cloth moistened with
kerosene or WD-40.

To avoid fire or toxic reaction, never use gasoline, naphtha,
acetone, lacquer thinner or similar highly volatile solvents
to clean the drill press.

rT._kVlV/_,1-1
_II_It"..]
Use only accessories designed for this drill press to avoid
injury from thrown broken parts or workpieces.
Sears may recommend other accessories not listed in
this manual. See your nearest Sears store or Power and
Hand Tool Catalog for other accessories.
Do not use any accessory unless you have completely
read the instruction or owner's manual for that accessory.

ITEM

DESCRIPTION

QUANTITY

A.
B.
C.
D.

Head assembly
Table
Base
Column assembly

1
1
1
1

E.
E
G.
H.
I.
J.
K.
L.
M.
N.
O.

Loose parts bag:
Feed handles
Lock handle
Crank handle
Hex bolts
Fence assembly
Triangle knobs
T-Block
Washer
Hex wrenches
Wedge
Arbor

3
1
1
4
1
2
2
2
3
1
1

P.
Q.

Box:
Chuck key
Chuck

\ J

II
Jl

}

r4_ =,

Belt guard cover
Belt pulleys
Belt tension handle
Belt tension lock knob

Light switch

Bert tension knob

ON/OFF

set screws

-UPper stop nut
nut

Depth stop
nut
Motor
- Spring cap
Cord clamp

Table

Feed spring

Rack

Power cord

Bevel scale
Quill

,crank
Table lock

Table support lock
_

pindle

5/8"Threadeddrain

Table arm

Column
support

Bevel Lock
set screw

Fence backstop

BASE - Supports the drill press. For additional stability,.
holesare provided in the base to bolt the drill press to
U_efloor.(See "Specific Safety Instructionsfor DriUPresses".)

DRILLING SPEED -Changed by placing the belt in any
of the steps (grooves) in the pulleys. See the Spindle
Speed Chart inside the belt guard.

BACKUP MATERIAL - A piec_eof scrap wood placed
betweenthe workpiece and table. The backup board
preventswood in the workpiece from splintering when the
drillpasses through the backside of the workpiece. It also
preventsdrilling into the table top.

FEED HANDLE - Moves the chuck up or down. If
necessary, one or two of the handles may be removed
whenever the workpiece is of such unusual shape that it
interferes with the handles.

BELT GUARD ASSEMBLY -Covers the pulleys and belt
duringoperation of the drill press.

FENCE - Attaches to the table to align the workpiece or
for fast rape"tdivedrilling.Removable. Remove fence when
it interferes with other drill press accessories.

BELTTENSION - Refer to the =Assembly" Section,
"Installing and Tensioning Belt."

HEAD LOCKS - Leeks the head to the column. ALWAYS
lock the head in place while operating the drill press.

BELTTENSION HANDLE -Turn the handle clockwise to
applytension to belt, turn the handle counterclockwise
to release belt tension.

RACK - Combines with gear mechanism to provide easy
elevation of the table by the hand operated table crank.

BELTTENSION LOCK KNOBS -Tightening the knobs
locksthe motor bracket support and the belt tension
handle,maintaining correct belt distance and tension.
BEVEL SCALE - Shows the degree of table tilt for bevel
operations.The scale is mounted on the side of the arm.
CHUCK - Holds the drill bit or other recommended
accessoryto perform desired operations.
CHUCK KEY - A self-ejecting chuck key which will pop
out of the chuck when you let go of it.This action is
designed to help prevent throwing of the chuck key from
thechuck when the power is turned "ON". Do not use
anyother key as a substitute;order a new one if damaged
or lost.
COLUMN - Connects the head, table, and base on a
one-piece tube for easy alignment and movement.
COLUMN COLLAR - Holds the rack to the column.
Rack remains movable in the collar to permit table
supportmovements.
COLUMN SUPPORT -Supports the column, guides the
rackand provides mounting holes for column to base.

DEPTHSCALE STOP NUTS - Lockthespindleto the
selecteddepth.
DEPTH SCALE - Indicates depth of hole being drilled.
DRILL BIT - The cutting tool used in the drill press to
make holes in a workpiece.

REVOLUTION PER MINUTE (R.P.M.) -The number of
turns completed by a spinning object in one minute.
SPINDLE SPEED -The

R.P.M. of the spindle.

SPRING CAP -Adjusts the quill spring tension.
TABLE SUPPORT LOCK -Tightening locks the table
support to the column. Always have it locked in place
while operating the drill press.
TABLE - Provides a working surface to support the
workpiece.
TABLE ARM - Extends beyond the table support for
mounting and aligning the table.
TABLE BEVEL LOCK - Locks the table in any position
from 0° - 45 °.
TABLE CRANK - Elevates and lowers the table. Turn
clockwise to elevate the table. Support lock must be
released before operating the crank.
TABLE LOCK - Locks the table after it is rotated to
various positions.
TABLE SUPPORT - Rides on the column to support the
table arm and table.
THREADED DRAIN (5/8") - Attach a 5/8" (pipe threaded)
metal pipe to the threaded opening for draining excess oil
into container. For a non-drainingsurface attach a threaded
metal plug. Pipe and plug not included.
WORKPIECE - Material being drilled.

DRILL ON/OFF SWITCH - Has locking feature. This
feature is intended to help prevent unauthorized and
possiblehazardous use by children and others. Insert the
key into the switch to turn the drill press on.

ASSEMBLY

INSTRUCTIONS

For your own safety, never connect plug to power source
outlet until all assembly and adjustment steps are
completed, and you have read and understood the safety
and operating instructions.

INSTALUNG THE TABLE (FIG. B and C)
1. Locate the table crank (1) and support lock (2) from
the loose parts beg.
2. Insert the support lock handle into the hole (3) at the
rear of the table support assembly. Tighten by hand.
3. Install the table crank handle onto the small
shaft (4), aligningthe set screw (5) with the fiat surface
of the shaft. Tighten the set screw with a hex wrench.

TOOLS NEEDED

Fig. B

Slotted ,screwdriver

8" & 10" Adjustable v,l_mches

4
Combination wrench

Combinationsquare

L' '"
Framingsquare

Socketwrench
with23 mm.socket
4.

The Ddll Press is very heavy and MUSTbe lifted with
the help of 2 PEOPLE OR MORE, to safely assemble it.
COLUMN SUPPOFITTO

BASE (FIG. A)

Place the column (2) on the base, aligning the
holes in the column supportwith the holes in the base.
1. Posltion the base (1) on the floor.
3. Locate the four long hex bolts (3) from the loose
parts bag.
4, Place a bolt in each hole through the column
support and the base, Tighten with an adjustable
w:nch.

Fig. A

•

2
i

(RG, C) Loosen the support lock (2). Raise the
table arm assembly by tuming the crank handle (1)
clockwise. Tighten he support lock.
Place the table 6) in the table arm asse bly. Tighten
the table lock handle (7).

Fig.
C°

INSTALLING THE HEAD (FIG. D)

TheDrill Press head is very heavy and MUST be lifted
withthe help of 2 PEOPLE OR MORE, to safely
assemblethe Drill Press head on the column.
1. Carefully liftthe head (1) above the column (2) and
slide it onto the column. Make sure the head slides
down over the column as far as possible. Align the
head with the base.
2, Using the hex wrench, tighten the two head lock set
screws (3) on the right side of the head.

Fig. D

INSTALLING FEED HANDLES (FIG. E)
1. Locate three feed handles in the loose parts bag.
2. Screw the feed handles (1) into the threaded holss (2)
in the hub (3). Tighten.

Fig. E

2 3

FENCE ASSEMBLY (RG. F)
This drillpress has a channeled table top.
1. Determine the desired locationfor the fenco (1). Slide
the T-blocks(2) into_ appropriatechannels as
shown.
2. Align the mountingholes of the fence over the T-block's
threaded holes.
3. Place a washer (3) on the threaded end of the knob (4).
Insert the knobthrough the mounting hole of the fence
into the T-block,and tighten.
4. Repeat for the other knob and T-block.

Fig. F

INSTALLINGTHE
CHUCK(RG. G,H,andI
1, Cleanoutthetaperedholeinthechuck(1)witha
2.

7. Using a rubber mallet, plastic-tipped hammer, or a
block of wood and a hammer, firmly tap the chuck
upward into position on the spindle shaft.

clean cloth.
Clean tapered surfaceson the ad_or(2) and spindle(3).

Fig. I

CAUTION: Make sure there are no foreign particles
sticking to the surfaces. The slightest piece of dirt on
any of these surfaces will prevent the chuck from
seating properly.This will cause the drill chuck and
bit to wobble. If tapered hole is extremely dirty, use a
cleaning solvent.

Fig. G

3.
4.

(FIG. H) Push the chuck (1) onto the spindle
arbor (2). Tap gently to ensure seat.
Lower the spindle by turning the feed handles (3)
counterclockwise,,until the slot (4) appears on the
quill (5).
Push the chuck and spindle arbor up intothe spindle,
making sure the tang (6) (upper narrow end of the
spindle arbor shank) is engaged and locked in the
inner slot (7) of the spindle. This can be seen
through the outer slot (4) of the quill by rotating the
chuck and arbor until the two slots are aligned.
Open the jaws of the chuck (1) by rotating the chuck
sleeve clockwise. To prevent damage, make sure the
jaws are completely receded into the chuck.

Fig. H

n ST J.U Suc rreuus(RG.J)(not
1.

Install a light bulb (no larger than 60 watt) intothe
socket inside the head.

Fig. J

DRILL PRESS ADJUSTMENTS

Fig. L

CAUTION: All the adjustments for the operation of the
drillpress have been completed at the factory, Due to
normalwear and use, some occasional readjustments
may be nesessary.
IP_WkrlVl_,1-'l_l_'l
Topreventpe_scoalinjury, always disconnectthe plug from
• e powersourcewhen making any adjustments.
SQUARINGTABLE TO HEAD (FIG. K and L)
4

NOTE: The table arm and support has a predrilled hole
witha lockingset screw inserted for locking the tab_ to
s predetermined0° horizontalposition.It must be loosened
tochangethe angle of the table.
1. Inserts 114",or larger diameter, precision ground
steel:rod(1), approximately 3" long, into the chuck (2).
Tightenthe chuck jaws.
2. Raise table to working height and lock.
3. Using the combination square (3), place one edge
fiaton the table, and align the other edge vertically
besidethe rod (1).

Fig. K

BEVEL SCALE (RG. L and M)
NOTE: The bevel scale has been included to measure
approximate bevel angles. If precision is necessary,
a square or other msasudng tool should be used to
position the table. To use the bevel scale (7):
1. Loosen the lockingset screw (4) to RELEASE it from
the table support.
2. Loosen the large hex head bevel locking bolt (6).
n_krAvl_,1-1
_ll_el
To prevent injury, be sure to hold the table & table arm
assembly, so it will not swivel or tilt.
3.
4.
5.

6.
r| |i

i i i t l i | i l iii

i i i

Tilt the table, aligning the desired angle measurement
to the zero line opposite the scale (7).
Tighten the bevel locking bolt. (6).
To return the table to its original position, loosen the
bevel locking bolt (6). Realign the bevel scale (7) to
the 0° position.
Tighten the locking set screw (#,) until it is seated in
the horizontal 0 ° hole of the table support.

Fig. M
L_

III

4. If an adjustment is necessary, loosen the locking set
screw(4) with the 3 mm he)( key to RELEASE the
tablefrom the horizontal position.
5. Loosenthe large hex head bevel locking bolt (6).
_vH,_,]iiLql_[9
Topreventinjury, be sure to hold the table & table arm
mssmbly,so it will not swivel or tilt.
6. Nign the square to the rod by rotating the table until
the square and rod are in line.
7. Relightanthe large hex bolt. (6).

6
7

Fig. O
To prevent personalinjury, always disconnectplug from the
power source when making any adjustments.
SPINDLE/QUILL (FIG. N)
Rotate the feed handles counterclockwise to lower
spindle to its lowest position. Hand support the spindle
securely and move it back and forth around its axis.
If there is too much play, do the following:
1. Loosen the lock nut (1).
2. Turn the screw (2) clockwise to eliminate the play, but
Without obstructingthe upward movement of the
spindle.(A littleplay in the spindle is normal.)
3. Tighten the lock nut (1).

Fig. N
mlW_Kql_
To avoidinjuryfrom an accidentalstart, ALWAYS make sure
the switchis in the "OFF" position,the sw#chkey m removed,
and the plug is not connestad to the powersource outlet
hence rce_
t_ ad]tmCmants.

QUILL RETURN SPRING (RG. O)
The quill return spring may need adjustment if the tension
causes the quill to return too rapidly or too slowly.
1. Lower the table for additional clearance.
2. Place a screwdriver in the lower front notch (1) of the
spring cap (2). Hold it in place while loosening and
removing only the outer jam nut (3).
3, With the screwdriver still engaged in the notch,
loosen the inner nut (4) just until the notch (5)
disengages from the boas (6) on the ddll press head.
CAUTION: DO NOT REMOVETHIS INNER NUT,
because the spring will forcibly unwind.
4.
5,

Carefully turn the spring cap (2) counterclockwisewith
the screwdriver, engaging the next notch.
Lower the quill to the lowest position by rotating the
feed handle in a counterclockwise direction while
holding the spring cap (2) in po6ition.
If the quill moves up and down as easily as you
desire, tighten the standard nut (4) with the adjustable
wrench. If too loose, repeat steps 2 through 5 to
tighten. If too tight, perform step 4, then 5.
DO NOT OVERTIGHTEN and restr_ quill movement.

Replace the jam nut (3) and tighten against the
standard nut (4) to prevent the standard nut from
reversing.

BELTTENSION (RG. P)
Make sure pulleys are aligned properly as shown in
Figure R on page 15.
1. To unlock the belt tension, turn the belt tension lock
knobs (1) on each side of the ddll press head
counterclockwise.
2. T'_fen the bolts by tuming the belt tensmn handle (2)
clockwise.
3. loosen the bolts by tuming the belt tension handle (2)
counterclockwise. Set belts on pulley steps for
desired speed.
4. Lock the belt tension lock knobs (1) by turning
clockwise.
NOTE: Belt tension is correct if the belt deflects
approximately 1/2 inch when pressed at its center.

Fig. P

To avoid injury from an accidental start, ALWAYS make
sure the switch is in the =OFF" position, the switch key is
removed,and the plug is not connected to the power
sourceoutlet before making belt adjustments
ALIGNINGTHE BELT PULLEYS (RG. Q)
Open the head cover of the Drill Press Check alignment
ofthe pulleys with a straight edge (5) such as a framing
square, a level, or a piece of wood Lay the straight edge
across the top of the pulleys If all three pulleys are NOT
aligned:
1 Release belt pressure by loosening the belt tension
lock knobs (4) on either side of the head, unlocking
the belt tension handle (1)
2 Loosen the motor mount nuts (2) Lift or lower the
motor (3) until the pulleys are in line.
3 Tighten the motor mount nuts (2) using an adjustable
wrench.
NOTE: To avoid rattles or other noise, the motor
housing should not touch the lower belt guard
housing.
Retighten the belts by turning the belt tension
handle (1) clockwise, until the belt deflects
approximately1F2inch when pressed in the center.

BASIC DRILL PRESS OPERATIONS
SPEEDS AND BELT PLACEMENT (FIG. R)
This drill press has 16 speeds, as listed below:
200 RPM
500 RPM
800 RPM
1820
290 RPM
580 RPM
870 RPM
2380
350 RPM
640 RPM
1440 RPM
2540
430 RPM
720 RPM
1630 RPM
3630

RPM
RPM
RPM
RPM

See inside of the belt guard for specific placement of the
belts on the pulleys to change speeds

To avoidpossible injury,keep guard closed, in place, and in
proper workingorder while tool is in operation

Fig. R
9

200 RPM

290 RPM

350 RPM

NOTE: Refer t;othe chart inside the belt guard
cover for recommended drilling speeds and
belt / pulley positions.
.

Lock the belt tens=onlock knobs (4) by tuming
clockwise

430 RPM

500 RPM

580 RPM

NOTE: When the belts are new, it may be difficultto
move the belts As the machine is used, the belts will
gain more elasticity and will be easier to adjust

64O RPM

Fig. Q

O
870 RPM

1820 RPM

0
1

72O RPM

800 RPM

1441) RPM

9
1630 RPM

2380 RPM

2540 RPM

ON / OFF SWITCH PANEL (FIG. S)
The "ON / OFF" switch has a removable, yellow plastic key.
With the key removed from the switch, unauthorized and
hazardous use by children and others is minimized.
1. To turn the drill press "ON", insert key (1) into the slot of
the switch (2), and move the switch upward to the "ON"
position.
2. To turn the drill press "OFF", move the switch downward.
3. To lock the switch in the =OFF" position, grasp the end,
or yellow part, of the switch toggle, and pull it out.
4. W=ththe switch key removed, the switch will not operate.
5. If the switch key is removed while the ddit press is
running, it can be turned =OFF" but cannot be restarted
without inserting the switch key.
6. To turn the worklight "ON", press the rocker switch (3).
7. Never leave the drill press unattended. "rumthe light
switch and power switch "OFF" and wait until it comes
to a complete stop.

Fig. S

@ =.
=-_3

_2
B1

@
tRg_
ALWAYSlock the switch=OFF"when the drillpress is not in use.
Remove the key and keep it in a safe place. In the event of a
power failure, blown fuse, or tripped circuit breaker, turn the
switch =OFF" and remove the key,preventing an accidental
sfartup when the power comes on.
INSTALLING DRILL BIT IN CHUCK (RG. 1")
1. With the switch "OFF" and the yellow switch key
removed, open the chuck jaws (1) using the chuck
key (2). Turn the chuck key counterclockwise to open
the chuck jaws (1).
2, Insert the drill bit (3) into the chuck far enough to obtain
maximum gripping by the jaws, but not far enough to
touch the spiral grooves (flutes) of the drill bit when the
jaws are tightened.
3. Make sure that the drill is centered in the chuck.
4. Turn the chuck key clockwise to tighten the jaws.

To avoid injury or accident by the chuck key ejecting
forcibly from the chuck when the power is turned "ON", use
only the self-ejecting chuck key supplied with this ddll press.
ALWAYS recheck and remove the chuck key before turning
the power "ON".

Fig. T

To prevent the workpiece or backup material from beingtorn
from your bands while drilling,you MUST positionthe
workpiece against the LEFT side of the column. If the
workpiece or the backup material is not long enough to reach
the column, clamp it to the table, oruse the fence provided
with the drill press to brace the workpiece.Failureto secure
the workpisca could result in personal injury.
USING THE FENCE (FIG. U)
The fence provides a way of accurately and quicklysetting
up the workpiece for more precision or for repetitive drilling
operations.
1. Using a centerpunch or sharp nail, make an
indentation in the workpiece where you want to drill.
2. Lower the drill bit to align with the indentationon the
workpiece. See =HOLDING A DRILLING LOCATION"
page 19.
3. Loosen the knobs (1) and slide the fence back stop (2)
firmly against the long side of the workpiece.Tighten
the knobs when in position.
4. Loosen the wing nut (3) and slide the end stop (4) along
the fence until it is firmly against the left side of the
workpiece. Tighten the wing nut.
5. Check the accuracy by drilling a scrap workpiece.
Adjust if needed.
6. Hold with your hand or clamp the top surface of the
workpiece firmly to prevent it from liftingoff the table
when the bit is raised.

Fig. U

234

DRILLING TO A SPECIRC DEPTH (RG. V)
Drilling a blind hole (not all the way through workpiece)
to a given depth can be done two ways:
Workplece method
1.
2.
3.
4.
5.
6.

Mark the depth (1) of the hole on the side of the
workpiece.
With the switch "OFF", bring the drill bit down until the
tip is even with the mark.
Hold the feed handle (2) at this position.
Spin the lowernut (3) down to contactthe depthstop (4)
on the head.
Spin the upper nut (5) down and tighten against the
lower nut (3).
The drill bit will now stop after travelingthe distance
marked on the workpiece.

LOCKING THE CHUCK AT THE DESIRED DEPTH
(RG. W)
1. With the switch "OFF', turn the feed handles until the
chuck (1) is at the desired depth. Hold the feed handles
at this position.
2. Turn the stop nut (2), located under the depth stop (3),
ceunterclockwise and upwards until it is against the
depth stop.
3. The chuck will now be held at this position when the
feed handles are released.

Depth scale method
NOTE: With the chuck up the tip of the ddll bit must be
just slightly above the top of the workpiece.
1.

With the switch "OFF', tum the feed handle (2) until the
depth stop (4) points to the desired depth on the depth
scale (6) and hold the feed handle in that position.
2. Spin the lower nut (3) down to contact the depth
stop (4).
3. Spin the upper nut (5) againstthe lower nut (3) and

tighten.
4.

The drill bit will stop after travelingthe distanceselected
on the depth scale.

Fig. V

REMOVING CHUCK AND ARBOR (FIG. X)
1. With the switchOFF, edjust the dopth stop nut (1) to
holdthe drillat a depth of three inches.(See instructions
for =LOCKING CHUCK AT DESIRED DEPTH").
2. Align the key holes in the spindle (2) and quill (3) by
rotating the chuck by hand.
3. Insert the key wedge (4) into the key holes (2 & 3).
4. Tap the key wedge (4) lightlywith a plastic tipped
hammer, until the chuck and arbor fall out of the
spindle.
NOTE: Place one hand below the chuck to catch it
when it falls out.

Fig. X

BASIC OPERATION INSTRUCTIONS

Use the SPINDLE SPEED recommended for the
specific operation and workpiece material. Check
the panel on the inside pulley cover or the chart
belowfor drillingspeed information. For accessories,
refer to the instructions provided with each
accessory.
5.
Never climb or*the drill press table, it could break or
pull the entire drill press down on you.
6. Turn the motor switch =OFF', and put away the
switch key when leaving the drill press.
7. To avoid injury from thrown work or tool contact, do
not perform layout, assembly, or set up work on the
table while the cutting tool is rotating.

To get the best results and minimize the likelihood of
personal injury, follow these instructionsfor operating your
drill press.

For your own safety, always observe the SAFETY
INSTRUCTIONS listed here and on pages 3, 4, and 5
of the instruction manual.

YOUR PROTECTION

To avoid being pulled into the power t0ol, do not wear
loose clothing, gloves, neckties, or jewelry. Always tie back
long hair,
1,

If any part of yourdrill press is missing,maffunctioning,
damaged or broken, stop operation immediately until
that part is propedy repaired or replaced,
2. Never place your fingers in a position where they
could contact the drill bit or other cutting tool. The
workpiece may unexpectedly shift, or your hand
could slip.
.
To avoid injury from parts thrown by the spring, follow
instructionsexactly when adjusting the springtension
of the quill.
4. To prevent the workpiece from being tom from your
hands, thrown, spun by the tool, or shattered, always
properly support your workpiece as follows:
a. Always position BACKUP MATERIAL (used
beneath workpiece) so that it contacts the left
side of the column, or use the fence provided and
a clamp to brace a smaller workpiece.
b.

DrillBit
Diam.
i (inches) Wood
1132

Material
num

Plastic

M|!d
Steel

Stainless

3630

363O

3630

1630
2830

1630
283O
87O
1440

870
1440

580
8OO

1/8
2'38O
2540
1630
2380

3/16
114
5/16

7/16
1/2

2380
2540
1630
2380

238O
254O
870
1440

3/8

or the table is tilted, use the fence provided or
clamp solidly to the table, using the table slots.
c. When using a drill press vise, always fasten it to
the table.
d. Never do any work freehand (hand-holding the
workpiece rather than supporting it on the table),
except when polishing.
e. Securely lock the head and support to the
column, the table arm to the support, and the table
to the table arm, before operating the drill press.
f.
Never move the head or the table while the tool
is running.
g. Before starting an operatico, _og the motor switch
to make sure the drill or other cutting tool does
not wobble or cause vibration.
h. If a workpiece overhangs the table so it will fall
or tip if not held, clamp it to the table or provide
auxiliary support.
L Use fixtures for unusual operations to adequately
hold, guide, and position workpiece.

.....

3630

SPEED TABLE (rpm)

1/16

Whenever possible, position the WORKPIECE to
contact the left side of the column. If it is too short

............................

DRILLING

350
5OO

35O
50O

200
290

870
1440

1630
2380
580
8OO

58O
8O0

580
800

9/16
5/8

___

......

POSITIONING THE TABLE ANDWORKPIECE
(FIG.Y,
and Z)
1. Lock the table (I) to the column (2) at a position so
the tip of the drill bit (3) is just above the top of the
workpiece (4).
2.

ALWAYS place a SACK-UP MATERIAL (scrap wood)
on the table beneath the workpiece. This will prevent
splintering or heavy burring on the underside of the
workpiece. To keep the beck-up material from
spinning out of control, it MUST contact the LEFT
side of the column.
For small pieces that cannot be clamped to the table,
use a drill press vise (optional accessory).

fRgf/_qK_
To prevent the workpiece or beckup material from being
tom from your hands while drilling, you MUST position it
against the LEFT side of the column, ff the workpisce or the
beckup matedal is not long enough to reach the column,
use the fence provided with the ddUpress to brace the
workpiece, or clamp it to the table. Failure to do this could
result in personal injury.

HOLDING A DRILLING LOCATION
1. Using a centerpunch or sharp nail, make an indentation
in the workpiece where you want the hole.
2. Using the feed handles, bang the ddll down to align
with the indentation before turning the drill ON,
TILTING THETABLE

(FIG. AA)

NOTE: The table arm and support (1) has a predrilled hole
with a locking set screw inserted for lockingthe table into a
predetermined 0° horizontal position.
1.

To use the table in a bevel (tilted) position,turn the
lockingset screw (2) with the hex key counterclockwise
to release it from the table support.
Loosen the large hex head bevel locking bolt (3).

To prevent injury, be sure to hold the table & table arm
assembly, so it will not swivel or tilt.
Fig. AA

Fig.Y

3
2
4

R_gf/i1_Kqi_e
The drill press vise MUST be clamped or bolted to the
table to avoid injury from a spinningworkpiece, or damaged
vise or bit parts.
Remove the ddll press fence when it interferes with other
drill press accessories.

Fig. Z

Tilt the table, aligningthe desired angle measurement
to the zero line opposite the ,scale (4). Tighten the bevel
locking bolt.
To return the table to its original position, loosen the
bevel locking bolt (3). Realign the bevel scale (4) to
the 0° position.
Using the hex key, turn the locking set screw (2)
clockwise to seat into the hole.

To avoid injury from spinning work or tool breakage,
always clamp workpieco end backup material securely to
the table before operating the ddU press with the table
tilted.
FEEDING
1. Pull down the feed handles with only enough effort to
allow the ddll bit to cut.
2. Feeding too slowly might cause the drill bit to burn.
Feeding too rapidly might stop the motor, cause the
belt or ddll to slip, or tear the workpiece loose and
break the ddll bit.
3, When ddlling metal, it may be necessary to lubricate
ttm drill bit tip with motor oil, to prevent burningthe tip.

MAINTAINING

YOUR DRILL PRESS

m L_ri1_]_qlLEe]
For your own safety, turn the switch "OFF' and remove
the plug from the power source outlet before maintaining
or lubricating your drill press.
Frequently blow out, using an air compressor or dust
vacuum, any dust that accumulates inside the motor.
A coat of automotive paste wax applied to the table and
column will help to keep the surfaces clean.

To avoid shock or fire hazard, if the power cord is worn
or cut in any way, have it replaced immediately.

LUBRICATION
All of the drill press ball bearings are packed with grease
at the factory. They require no further lubrication.
Periodically lubricate the gear and rack, table elevation
mechanism of the spindle and the rack (teeth) of the quill.

TROUBLESHOOTING

GUIDE

To avoid injury from an accidental start, turn the switch "OFF" and always remove the plug from the power source before
making any adjustments.
• Consult your local Sears Service Center if for any reason the motor will not run.
PROBLEM

PROBABLE CAUSE

REMEDY

Noisy operation.

1. Incorrect belt tension.

1. Adjust tension. See Section
"ASSEMBLY - TENSIONING BELT"
2. Lubricate spindle. See Section "LUBRICATION".
3. Check tightness of retaining nut on pulley, and
tighten if necessary.
4. Tighten set screw in motor pulley.

2. Dry spindle.
3. Loose spindle pulley.
4. Loose motor pulley.
Ddll bit burns.

2.
3.
4.
5.

Run out of ddll bit point drilled hole not round.

1. Change speed. See Section "BASIC DRILL
PRESS OPERATION - SPINDLE SPEEDS"
Chips not coming out of hole. I 2. Retract drillfrequently to clear chips.
Dull drill bit.
3. Resharpen drill bit.
Feeding too slowly.
4. Feed fast enough - allow drill to cut.
Not lubricated.
5. Lubricate drill. See Section "BASIC
DRILL PRESS OPERATION-FEEDING"

1. Incorrect speed.

1. Hard grain in wood or
lengths of cutting flutes
and/or angles not equal.
2. Bent drill bit.

1. Resharpen drill bit correctly.

2. Replace drill bit.

Wood splinters on
underside.

1. No backup material
under workpiece.

1. Use backup material. See Section
"BASIC DRILL PRESS OPERATION".

Workpiece torn
loose from hand.

1. Not supported or
clamped properly.

1. Support workpiece or clamp it. See Section
"BASIC DRILL PRESS OPERATION".

Drill bit binds in workpiece.

1, Workpiece pinching ddll bit,
or excessive feed pressure.
2. improper belt tension.

1. Support workpiece or clamp it. See Section
"BASIC DRILL PRESS OPERATION".
2. Adjust tension. See Section
"ASSEMBLY - TENSIONING BELT"

Excessive drill bit
runoutor wobble.

1. Bent drill bit.
2. Worn bearings.
3. Drill bit not propedy
installed in chuck.
4. Chuck not propedy installed.

1. Use a straight drill bit.
2. Replace bearings.
3. Install ddll properly. See Section "BASIC DRILL
PRESS OPERATION" and "ASSEMBLY".
4. Install chuck properly. See Section
"ASSEMBLY -INSTALLING THE CHUCK".

Quill returns
too slow or too fast.

1. Spring has improper tension.

1. Adjust spdng tension. See Section "ASSEMBLYADJUSTMENTS - QUILL RETURN SPRING".

Chuck will not stay
attachedto spindle.
It falls off when
trying to install.

1. Dirt, grease, or oil on the
tapered inside surface of
chuck or on the spindle's
tapered surface.

Using a household detergent, clean the
tapered surface of the chuck and spindle to
remove all dirt, grease and oil. See Section
"ASSEMBLY - INSTALLING THE CHUCK"

17" DRILL PRESS PARTS LIST

MODEL NO. 137.229171

When servicing use only CRAFTSMAN replacement parts. Use of any other parts may create a HAZARD or cause
product damage,

Any attempt to repair or replace electrical parts on this Drill Press may create a HAZARD unless repair is done by a
qualified service technician. Repair service is available at your nearest Sears Service Center.
Always order by PART NUMBER, not by key number.
Key

Description

0SUE

BASE

0SGB

COLUNM

Size

Qty.

ASS'Y

0JQO

HEX.

06RY

TABLE

HD.

BOLT

M10"1.5_40

05UW

WORM

05UY

CRANK

HANDLE
SCALE

BRACKET

0SVB

TILT)NG

06RZ

CENTER(NG

OSGF

COLUMN

OBVD

TABLE

(_$1

ASS'Y

SCALE
LOCK

Description

C_SY

SWITCH

OKDK

CR.

Size

Qty.

BOX

RE.

PAN

HD.

OSG4

PULLEY

OSGL

CENTER

OJHK

V-BELT

OJSF

FLAT

WASHER

0KPX

HEX.

NUT

04A4

CLAMP-CORD

SCREW

COVER

iS'O.8-1B

ASS'Y

PULLEY

ASS'Y

1
1

1/2"20

T=6.5

2
3

CR.

061R

CHUCK

TABLE

0JHH

V-BELT

05VQ

RACK

CBTS

SWITCH

06K1

RACK

RiNG

0Kg4

O6S9

HEAD

ASS'Y

CBKV

MOTOR

ROD

0JXL

HEX,

OJCM

SPRING

062X

WARNING

22B1

MOTOR

LABEL

22AY

SPEED

DIAGRAM

04Q4

STICKER

OSGY

TRADE-MARK

0KgX

DRIVE

SCREW

OK9X

DRIVE

SCREW

OSG3

HARDWARE

SOC

HANDLE

ASS'Y

SET

SCREW

072B

HANDLE

05WL

MOTOR

BAR

06K9

MOTOR

ROD

OSGN

SHIFTER

05WV

MOTOR

BASE

OJ9M

SPRING

WASHER

M10"1

5-12

SHIFTER
SHIFTER

ASS'Y

BOLT

OKMX

HEX.

NUT

OSGP

HUB

ASS'Y

OSGG

HANDLE

"_1/'Z'
M12"1.75

BAR

T=I

ASS'Y

RE.

OKDH

LOCK

HANDLE

Key

PAN

HD.

KEY

HOLDER

RE,

0J7J

FLAT

WASHER

0712

PARALLEL

0713

SLIDE

M10"1.5-28

OKJO

CAP

M10*I.BT---8

0714

PLATE

OKQS

WING

OBSK

BULB

OKFF

DR.

SPRING

CAP

SPR(NG

RETAINER

0_Y2

QUILL

OKMV

HEX.

BSB8

SPINDLE

ASS"(

OSGK

DRIVING

SLEEVE

CBYS

PULLEY

CBSR

SPINDLE

PULLEY

OJAF

EXTERNAL

OHY8

DRILLING

ARBOR

OKDZ

0J28

CHUCKS

KEY

06HB

PLUNGER

OKMU

HEX.

NUT

OSGE

SET

BOLT

0eCR

NUT

OSGZ

CHUCK

OSHO

CHUCK

0_7-2

WEDGE

0Q4B

MOTOR

0K18

HEX.

HD.

0J7F

FLAT
HEX.

OKMY

NUT

KEY
SHIFTER

RE.

5/16"7/8-5/64

0715

SET

NUT

M8"I

MOTOR

0JG4

PARALLEL

(_SV

PULLEY
KEy

ASB'Y

_ 2.3_5

2
1

AES'Y

2
5/32-7/_

2
1
2

SQ.NECK

BOLT

M6"1.0-16

MBX1.0

PAN

HD.

SCREW

TOOTH
PAN

ASS'Y

LOCK

M5*O.8_

WASHER

SCREW

2
(- " +) M6"1 0"35

M10"1.5

HOUSING

ASS'Y

T=8

1
M16"2.0

WASHER

06ST

348"1

SOCKET

HEX.

, T-_

_p2.3-5

WASHER

.25

NUT

0JUY

WASHER

BRACKET

HD.

0_3G
AND

M5"12-16

PLATE

M*1,25

SCREW

SCREV

BAG

05Y1

SET

TAPPING

LABEL

KNOB

ASS'Y

HD,

0VJK

NUT

LABEL

SCALE

SCREW

TRUSS

0GXK

SET

5.8

LOCK

ASS'Y

MB'O

COVER

0711

RING

SCREW

2
1

SOC.

HD.

CAP

BOLT

M8"1

RING

1
1

06HG

CIRCULAR

NUT

OKDU

CR.

RE.

PAN

OKTK

CR.

RE.

ROUND

HD.

1
SCREW
WASHER

HD.

SCRE'I

M6"1.0-12

CLAMp-CORD

0J3M

WRENCH

HEX.

OKUW

TERMINAL

OJ:30

WRENCH

HEX.

0LWG

ROCKER

0J3R

WRENCH

HE,X.

OKYN

LEAD

OKSG

STRAIN

SWITCH

WIRE

ASS_(

RELIEF

1
1

17" DRILL PRESS

PARTS

LIST

MODEL

NO. 137.229171

05YS

22AY

OSGG

05XK
/

072B

0°TS

OWK

OIGPV
OKPX

05Z2

0SGF
O.13M

05YD

OIQO

0714
0KQ5

Get it fixed, at your home or ours!
Your Home
For repair-in your home-of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
Operator's Manuals that you need to do-it-yourself
For Sears professional installation of home apphances
and items hke garage door openers and water heaters.

1-800-4-MY-HOME ® (1-800-469-4663)
Call anytime, day or mght (U S A. and Canada)
www.sears.com

www.sears.ca

Our Home
For repair of carry-m items like vacuums, lawn equspment,
and electromcs, call or go on-hne for the location of your nearest
Sears Parts & Repair Center.

1-800-488-1222
Call anytime, day or night (U S A only)
www.sears.com

To purchase a protection agreement (U.S.A)
or maintenance agreement (Canada) on a product serviced by Sears
1-800-827-6655
(u S A )
1-800-361-6665
(Canada)
Para pedlr servIC!O de reparaclon
a dOmlclho, y para ordenar plezas
1-888-SU-HOGAR
sM

Au Canada pour service en fran_:a=s

1-800-LE-FOYER

(1-800-533-6937)
www sears ca

(1-888-784-6427)

SEARS
® Registered
® Marca
uc Marque

Trademark

/ TM Trademark

Reglstrada / Te Marca
de commerce

I _M Service Mark of Sears

de Fabric2, / s_, Marca de Serwclo

/ Mo Marque deposee

ae Sears

Roebuck and Co

de Sears

Roebuck and Co

Roebuck and Co
_, Sears

Roebuck and CO

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 25
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Tue Apr 03 14:39:39 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 137229170 User Manual 17 DRILL PRESS Manuals And Guides L0308059

CRAFTSMAN Drill Press Manual L0308059 CRAFTSMAN Drill Press Owner's Manual, CRAFTSMAN Drill Press installation guides

Navigation menu

Versions of this User Manual:

Views

Navigation