Craftsman 315243000 User Manual 10 COMPOUND MITER SAW Manuals And Guides L0050127

CRAFTSMAN Miter Saw Manual L0050127 CRAFTSMAN Miter Saw Owner's Manual, CRAFTSMAN Miter Saw installation guides

DURA-GLAS IITM P4RAG6C-150 L0050127

User Manual: Craftsman 315243000 315243000 CRAFTSMAN 10 COMPOUND MITER SAW - Manuals and Guides View the owners manual for your CRAFTSMAN 10 COMPOUND MITER SAW #315243000. Home:Tool Parts:Craftsman Parts:Craftsman 10 COMPOUND MITER SAW Manual

Open the PDF directly: View PDF .
Page Count: 38

Download
Open PDF In Browser	View PDF

Owner's Manual

CRRFTSMRN'I
10 in.
COMPOUND MITER SAW
Double Insulated
Model No.
315.243000

Save this manual for
future reference

•
•
•
•
•
•

CAUTION:

Read and follow
all Safety Rules and Operating
Instructions before first use of
this product.
Customer
Sears,

Help Line: 1-800-932-3188
Roebuck

Visit the Craftsman
972000-710
1-00

and Co.,

Hoffman

web page:

Estates,

IL 60179

Safety
Features
Adjustments
Operation
Maintenance
Parts List

USA

www.sears.com/craftsman
NRTL/C

•

Table of Contents

...........................................................................................................................................

•

Warranty

•

Rules For Safe Operation

•

Glossary

•

Product

•

Labels .............................................................................................................................................................

•

Loose Parts and Tools Needed ......................................................................................................................

•

Features

•

Adjustments

•

Operation

•

Maintenance

•

Exploded

•

Parts Ordering / Service ...............................................................................................................................

and Introduction

..............................................................................................................................
...........................................................................................................................

2
3-6

.........................................................................................................................................................
Specifications

and Unpacking

..........................................................................................................

..................................................................................................................................................

10-12

.............................................................................................................................................

12-19

.................................................................................................................................................

20-26

............................................................................................................................................

27-28

View and Repair Parts List ......................................................................................................

30-37
38

FULL ONE YEAR WARRANTY
If this product fails due to a defect in material or workmanship within one year from the date of purchase,
Sears will repair it free of charge.
Contact a Sears Service Center for repair.
If this product is used for commercial or rental purposes, this warranty applies only for 90 days from the date
of purchase.
This warranty gives you specific legal rights, and you may also have other rightswhich vary from state to state.
Sears, Roebuck and Co., Dept. 817WA, Hoffman Estates, IL 60179

Your saw has many features for making cutting
operations more pleasant and enjoyable. Safety,
performance
and dependability
have been given top
priority in the design of this saw making it easy to
maintain and operate.

Look for this symbol to point out important
Your safety is involved.

_1,

safety

CAUTION: Carefully read through this entire
owner's manual before using your new saw. Pay
close attention to the Rules For Safe Operation,
and all Safety Alert Symbols including Danger,
Warning and Caution. If you use your saw
properly and only for what it is intended, you will
enjoy years of safe, reliable service.
precautions.

It means'attention!!!

WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes,
which can result in severe eye damage. Before beginning power tool operation, always
wear safety goggles or safety glasses with side shields and a full face shield when needed.
We recommend Wide Vision Safety Mask for use over eyeglasses or standard safety
glasses with side shields, available at Sears Retail Stores.

The purpose of safety symbols is to attract your attention to possible dangers, The safety symbols, and
the explanations
with them, deserve your careful attention and understanding.
The safety warnings do
not by themselves
eliminate any danger, The instructions or warnings they give are not substitutes for
proper accident prevention measures.

SYMBOL

MEANING
SAFETY

ALERT

SYMBOL:

Indicates danger, warning or caution. May be used in conjunction
graphs.

with other symbols

or picto-

DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others
Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.

,a,

WARNING:
Failure to obey a safety warning can result in serious injury to yourself or to others.
Always follow the safety precauttons to reduce the risk of fire, electric shock and personal iniury

CAUTION:
Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the esk of fire, electric shock
and personal injury,

NOTE:

Advises you of informatLon or instructions

DOUBLE

INSULATION

vital to the operation

or maintenance

of the equipment.

IMPORTANT

Double insulation =sa concept in safety, in electric
power tools, which eliminates the need for the usual
three-wire grounded power cord All exposed metal
parts are isolated from internal metal motor
components with protecting insulation Double
insulated tools do not need to be grounded.

Servicing requires extreme care and knowledge of the
system and should be performed only by a qualified
service technician. For service we suggest you return
the tool to your nearest Sears store for repair. Always
use original factory replacement parts when servicing.

•

KEEP THE WORK AREA CLEAN. Cluttered work
areas and work benches invite accidents. DO
NOT leave tools or pieces of wood on the saw
while it is in operation.

•

DO NOT USE IN DANGEROUS

WARNING:
Do not attempt to operate thrs tool
until you have read thoroughly and understand
completely all instructtons, safety rules, etc.
contained in this manual Failure to comply can
result in accidents involving fire. electric shock,
or serious personal injury. Save owner's manual
and review frequently for continuing safe
operation, and instructing others who may use
this tool.

READ

ALL

INSTRUCTIONS

KEEP CHILDREN

KNOW YOUR POWER TOOL. Read the owner's
manual carefully. Learn the saw's applications
and limitations as well as the specific potential
hazards related to this tool
•

GUARD AGAINST ELECTRICAL
PREVENTING
BODY CONTACT

SHOCK
WITH

GROUNDED
SURFACES, For example; pipes,
radiators, ranges, refrigerator enclosures.
•

KEEP GUARDS
order.
REMOVE

IN PLACE

ADJUSTING

and in good working

KEYS AND

WRENCHES.
Get in the habit of checking to see
that hex keys and adjusting wrenches are
removed from tool before turning on saw

ENVIRON-

MENTS, Do not use power tools near gasoline or
other flammable liquids, in damp or wet locations,
or expose them to rain Keep the work area well
lit,
AND VISITORS

AWAY. All

visitors should wear safety glasses and be kept a
safe distance from work area Do not let visitors
contact

tool or extens=on cord whde operating.

MAKE WORKSHOP
CHILD-PROOF
w=th padlocks and master switches or by removrng starter
keys.
DO NOT FORCE THE TOOL. It will do the job
better and safer at the rate for which it was
designed.

USE THE RIGHT TOOL. Do not force the tool or
attachment to do a job it was not designed for.
Don't use it for a purpose not intended.

RULES

FOR SAFE

USE THE PROPER

OPERATION
EXTENSION

(Continued)

CORD.

Make

function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting and any other conditions that may
affect its operation. A guard or other part that is
damaged must be properly repaired or replaced
by a qualified service technician at a Sears store
to avoid risk of personal injury.

sure your extension cord is in good condition.
When using an extension cord, be sure to use
one heavy enough to carry the current your
product will draw. An undersized cord will cause
a drop in line voltage resulting in loss of power
and overheating. A wire gage size (A W.G ) of at
least 14 is recommended for an extension cord
25 feet or less in length. If in doubt, use the next
heavier gage. The smaller the gage number, the
heavier the cord
INSPECT
CALLY

EXTENSION

CORDS

NEVER LEAVE TOOL RUNNING UNATTENDED. TURN THE POWER OFF. Do not
leave tool until it comes to a complete stop.
FIRMLY

PERIODI-

and replace if damaged.

incorrect. The maximum
saw is 10 in.

PROTECT YOUR LUNGS. Wear a face or dust
mask if the cutting operation is dusty,

hip height.

blade capacity

of your

•

DO NOT REMOVE THE SAW'S BLADE
GUARDS. Never operate the saw with any guard
or cover removed. Make sure all guards are
operating properly before each use.

•

KEEP HANDS AWAY FROM CUTTING AREA.
Keep hands away from blades. Do not reach
underneath work or around or under the blade
while blade is rotating. Do not attempt to remove
cut material when blade is moving.

WARNING:

•

DO NOT ABUSE CORD. Never yank cord to
disconnect it from receptacle. Keep cord from
heat, oil, and sharp edges.

PROTECT YOUR HEARING. Wear hearing
protection during extended periods of operation.
SECURE WORK. Use clamps or a vise to hold
work when practical. It's safer than using your
hand and it frees both hands to operate tool,

Blade coasts after turn off.

Keep proper footing and

MAINTAIN TOOLS WITH CARE. Keep tools
sharp and clean for better and safer performance. Follow instructions for lubricating and
changing accessories.

INSPECT

TOOL

CORDS

PERIODICALLY

and if

DISCONNECT
ALL TOOLS. When not in use,
before servicing, or when changing attachments,
blades, bits, cutters, etc., all tools should be

damaged, have repaired by a qualified service
technician at a Sears store. Stay constantly
aware of cord location and keep it well away
from the rotating blade.

disconnected.

USE OUTDOOR

•

AVOID ACCIDENTAL
STARTING.
switch is off when plugging in.

•

USE RECOMMENDED

EXTENSION

CORDS.

When

tool is used outdoors, use only extension cords
with approved ground connection that are
intended for use outdoors and so marked.

Be sure

ACCESSORIES.

use of improper accessories
injury.

•

your miter saw to a

KEEP BLADES CLEAN, SHARP AND WITH
SUFFICIENT SET, Sharp blades minimize
stalling and kickback.

ALWAYS WEAR SAFETY GLASSES WITH
SIDE SHIELDS, Everyday eyeglasses have only
impact-resistant lenses; they are NOT safety
glasses,

•

OR BOLT

or table at approximately

USE ONLY CORRECT BLADES. Do not use
blades with incorrect size holes. Never use blade
washers or blade bolts that are defective or

DRESS PROPERLY. Do not wear loose clothing,
gloves, neckties, rings, bracelets, or other
jewelry. They can get caught and draw you into
moving parts Rubber gloves and nonslip footwear are recommended
when working outdoors.
Also wear protective hair covering to contain long
hair

DO NOT OVERREACH.
balance at all times.

CLAMP

workbench

The

DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by a qualified service technician at a
Sears store.

may cause risk of

NEVER STAND ON TOOL. Serious injury could
occur if the tool is tipped or if the blade is unintentionally contacted.

KEEP TOOL DRY, CLEAN, AND FREE FROM
OIL AND GREASE. Always use a clean cloth
when cleaning. Never use brake fluids, gasoline,
petroleum-based products, or any solvents to
clean tool.

CHECK DAMAGED PARTS. Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine that it
will operate properly and perform its intended

RULES
•

FOR SAFE

ALWAYS

SUPPORT

OPERATION

(Continued)

LONG WORKPIECES

•

NEVER reach to pick up a workpiece, a piece of
scrap, or anything else that is in or near the
cutting path of the blade.

•

AVOID AWKWARD

minimize risk of blade pinching and kickback.
Saw may slip, walk, or slide while cutting long or
heavy boards.
•

BEFORE MAKING A CUT, BE SURE ALL
ADJUSTMENTS
ARE SECURE.

•

GUARD AGAINST KICKBACK.
Kickback occurs
when the blade stalls rapidly and workpiece is
driven back towards the operator. It can pull your
hand into the blade resulting in serious personal
injury. Stay out of blade path and turn switch off
immediately if blade binds or stalls.

•

AVOID CUTTING NAILS. Inspect for and
remove all nails from lumber before cutting.

•

ALWAYS

USE A CLAMP

to secure the work-

NEVER TOUCH
during use.

BLADE

or other moving

•

NEVER START A TOOL WHEN THE BLADE IS
IN CONTACT WITH WORKPIECE.
Allow motor
to come up to full speed before starting cut.

•

MAKE SURE THE MITER TABLE

•

NEVER stand or have any part of your body in
line with the path of the saw blade.

•

ALWAYS release the power switch and allow the
saw blade to stop rotating before raising it out of
the workpiece.

•

DO NOT TURN THE MOTOR SWITCH ON AND
OFF RAPIDLY. This could cause the saw blade
to loosen and could create a hazard. Should this
ever occur, stand clear and allow the saw blade
to come to a complete stop. Disconnect your saw
from the power supply and securely retighten the
blade bolt.

parts

REPLACEMENT PARTS. All repairs, whether
electrical or mechanical, should be made by
qualified service technician at a Sears store.

AND SAW

ARM (BEVEL FUNCTION)
ARE LOCKED IN
POSITION BEFORE OPERATING
YOUR SAW.
Lock the miter table by securely tightening the
miter lock handle. Lock the saw arm (bevel
function) by securely tightening the bevel lock
knob.
•

NEVER
SCRAP

USE A LENGTH STOP ON THE FREE
END OF A CLAMPED WORKPIECE.

NEVER hold onto or bind the free scrap end of
the workpiece in any operation. If a work clamp
and length stop are used together, they must
both be installed on the same side ol the saw
table to prevent the saw from catching the loose
end and kicking up.
•

NEVER cut more than one piece at a time. DO
NOT STACK more than one workpiece on the
saw table at a time.
NEVER

PERFORM

ANY OPERATION

"FREE-

HAND". Always place the workpiece to be cut on
the miter table and position it firmly against the
fence as a backstop. Always use the fence.

NEVER hand hold a workpiece that is too small
to be clamped. Keep hands clear of the no hands
zone
NEVER reach behind, under, or within three
inches of the blade and its cutting path with your
hands and fingers for any reason.

AND HAND

POSITIONS where a sudden slip could cause
your hand to move into the blade. ALWAYS
make sure you have good balance. NEVER
operate your miter saw on the floor or in a
crouched position.

piece when possible.
•

OPERATIONS

WARNING: When servicing use only identical
Craftsman replacement parts. Use of any other
parts may create a hazard or cause product
damage.
NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could
ignite fumes.
NEVER leave the miter saw unattended while
connected to a power source.
POLARIZED

PLUGS.

To reduce the risk of

electric shock, this tool has a polarized plug (one
blade is wider than the other). This plug will fit in
a polarized outlet only one way. If the plug does
not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician to
install the proper outlet. Do not change the plug
in any way.
IF ANY PART OF THIS MITER SAW IS MISSING or should break, bend, or fail in any way, or
should any electrical component fail to perform
properly, shut off the power switch, remove the
miter saw plug from the power source and have
damaged, missing, or failed parts replaced
before resuming operation.
DO NOT OPERATE THIS TOOL WHILE UNDER THE INFLUENCE OF DRUGS, ALCOHOL,
OR ANY MEDICATION.

RULES
•

•

FOR SAFE

OPERATION

(Continued)

ALWAYS STAY ALERT! Do not allow familiarity
(gained from frequent use of your saw) to cause
a careless mistake. ALWAYS REMEMBER that
a careless fraction of a second is sufficientto

•

MAKE SURE THE WORK AREA HAS AMPLE
LIGHTING to see the work and that no obstructions will interfere with safe operation BEFORE
performing any work using your saw.

inflict severe injury.
STAY ALERT AND EXERCISE CONTROL.
Watch what you are doing and use common

•

ALWAYS TURN OFF SAW before disconnecting
it, to avoid accidental starting when re-connecting to power supply.

sense. Do not operate tool when you are tired.
Do not rush.

•

SAVE THESE INSTRUCTIONS. Refer to them
frequently and use to instructother users. If you
Loan someone this tool, loan them these instroctions also.

SAVE THESE INSTRUCTIONS

Arbor
The shaft on which a blade or cutting tool is mounted.
Bevel Cut
A cutting operation made with the blade at any angle
other than 90" to the miter table,
Crosscut
A cutting or shaping operation made across the grain
of the workpiece.
Compound Miter Cut
A compound miter cut is a cut made using a miter
angle and a bevel angle at the same time.
Freehand
Performing a cut without using a fence, miter gage,
fixture, work clamp, or other proper device to keep the
workpiece from twisting or moving during the cut.
Gum
A sticky, sap based residue from wood products.
Miter Cut
A cutting operation made with the blade at any angle
other than 90" to the fence.
Resin
A sticky, sap base substance that has hardened.
Revolutions Per Minute (RPM)
The number of turns completed by a spinning object
in one minute.
Saw Blade Path
The area over, under, behind, or in front of the blade.
As it applies to the workpiece, that area which will be,
or has been, cut by the blade.

Set
The distance that the tip of the sawblada tooth is bent
(or set) outward from the face of the blade,
Throw-Back
Throwing of a workpiece in a manner similar to a
kickback. Usually associated with a cause other than
the kerf closing, such as a workpiece not being
against the fence, being dropped into the blade, or
being placed inadvertently in contact with the blade.
Through Sawing
Any cutting operation where the blade extends
completely through the thickness of the workpiece.

Workpiece
Theitem on whichthe cu_ing oper_ionis being done.
The surfaces ofa workpiece are commonlyreferredto
asfaces, ends, and edges.
Zero Clearance Throat Plate
A plastic throat plate inserted in the miter table that
allowsfor blade clearance. When you make your first
cut with your compound miter saw, the saw blade cuts
a slot through the throat plate the exact width of the
blade. This provides for a zero clearance kerr that
minimizes workpiece tear-out.
No Hands Zone
The area between the marked lines on the left and
right side of the miter table base. This zone is
identified by no hands zone labels placed inside the
marked lines on the miter table base.

Blade Diameter
Blade Arbor
No Load Speed
Rating
Input

i 0 in.

Cutting Capacity

5/8 in.
5000 RPM

Maximum

120 Volts, 60 Hz-AC Only

0°:

Cutting Capacity

with Miter at 45°/Bevel

0°:

3-15/16 in. wide X 2-9/32 in. thick

15 Amperes

Net Weight

with Miter at 0°/Bevel

5-9/16 in. wide X 2-9/32 in. thick
3-9/16 in. thick X 4 in. wide

Maximum

32 Ibs.

Cutting Capacity

with Miter at 0°/Bevel

45°:

5-9/16 in. wide X 1-9/16 in. thick
Maximum

Cutting Capacity

with Miter at 45°/Bevel

45°:

4 in. wide X 1-9/16 in. thick

Your Compound Miter Saw has been shipped
completely assembled except for the blade, miter lock
handle, and dust guide.

•

WARNING: If any parts are missing, do not
operate this tool until the missing parts are
replaced. Failure to do so could result in possible
serious personal injury.

•

Your saw has been shipped with the saw arm
locked in the down position. To release saw arm,
push down on top of saw arm and pull out the lock
pin. See Figure 4.

Remove all loose parts from the carton. Separate
and check with the list of loose parts. See Figure 2.

•

Lift the saw arm by the handle. Hand pressure
should remain on the saw arm to prevent sudden
rise upon release of the lock pin.

•

Examine all parts to make sure no breakage or
damage has occurred during shipping.

Do not discard the packing materials until you
have carefully inspected the saw, identified all
loose parts, and satisfactoriry operated your new
saw.

•
•

Remove the packing materials from around your
saw.

•

Carefully lift saw from the carton and place it on a
level work surface. This saw is heavy. To avoid
back injury, get help when needed.

If any parts are damaged or missing, do not attempt to
plug in the power cord and turn the switch on until the
damaged or missing parts are obtained and are
installed correctly.

The following labels are on the miter saw with locations indicated.

Restorelower blade guard
and securely tighten screw
before use

e Change. See Owner's Man

DANGER:

DO NOT REMOVE

ANY GUARD. USE OF SAW
WITHOUT THIS GUARD WILL
RESULT IN SERIOUS INJURY.

41WARNING/ ADVERTENCIA
• For your safety, read owners manual before operating
miter saw.
• Wear eye protection.
• Keep hands out of path of saw blade,
• Do not operate saw without guards in place,
• Do not perform any operation freehand.
• Never reach around the saw blade.
• Turn off tool and wait for saw blade to stop before
moving workpiece or changing settings.
• Disconnect the saw from the power source before
changing blade or servicing,
• Do not expose to rain or usa in damp places.
• Psra su saguridad, lea el manual del usuario antes
de usar la sierra ingletadora.

10 inch Compound

Miter Saw

DOUBLE
INSULATED
5,OOO
RPM120VOLTS
60Hz ACONLY
15A

WARNING: WHEN SERVICING,

USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS,
MODEL

315,243000

MADE iNROEBUCKAND
TArWAN
SEARS,
CO.

SER NO
[

_i
]

v,m_c
rrA_ON_W¢
_

• Customer Help Line 1-800-932-3188
Fig. 1

The following items are included with your Compound Miter Saw:
•

Saw Blade - 10 in.

•

5 mm Hex Key Wrench

•

Miter Lock Handle

•

6 mm Hex Key Wrench

D_:tt Gui:e

•
•

8 mm Hex Key Wrench
Owner's Manual

•

Blade Wrench
BLADEWRENCH

__HEX

SAWBLADE

KEY

_KEY
MITERLOCKHANDLE

DUST BAG
Fig. 2
_,

WARNING:

The use o! attachments or accessories not listed might be hazardous and could
cause serious personal injury,

The following tools (not included) are needed for checking adjustments of your saw or for installing the blade:

17 mm COMBINATION
WRENCH
10 mm COMBINATION
WRENCH
SQUARE

FRAMINGSQUARE
PHILLIPS SCREWDRIVER

KNOW
SAW

YOUR

COMPOUND

MITER

ELECTRIC

BRAKE

See Figure 3.

An electric brake has been provided to quickly stop
blade rotation after the switch is released.

Before attempting to use your saw, familiarize yourself
with all operating features and safety requirements.

FENCE

The fence on your compound miter saw has been
provided to hold your workpiece securely against
when making all cuts.

WARNING: Do not allow familiarity with your
saw to make you careless. Remember that a
careless fraction of a second is sufficient to inflict
severe injury.

SELF-RETRACTING
GUARD

15 AMP MOTOR

LOWER

BLADE

The lower blade guard is made of shock-resistant,
see-through plastic that provides protection from each
side of the blade. It retracts over the upper blade
guard as the saw is lowered into the workpiece.

Your saw has a powerful 15 amp motor with sufficient
power to handle tough cutting jobs. It is made with all
ball bearings, and has externally accessible brushes
for ease of servicing.

MITER

LOCK

HANDLE

See Figure 4.

10 in. BLADE

The miter lock handle securely locks your saw at
desired miter angles.

A 10 in. saw blade is included with your compound
miter saw. It will cut materials up to 2-5/8 in. thick or
5-3/4 in. wide, depending upon the thickness of the
material and the setting at which the cut is being
made.
SWITCH
LOCK-OFFLEVER
DUSTBAG

UPPER
BLADE GUARD

SWITCHTRIGGER

BLADEGUARD
BEVEL

MITERTABLE
ZONE LABEL
"NO HANDS ZONE"
LINE

FEN

ZEROCLEARANCE

LOCK PLATE

MITER

CONTROLARM

LOCKHANDLE

POSITIVESTOP(S)
Fig. 3
10

CARRYING

HANDLE

LOCK-OFF
LEVER

See Figure 4.

SPINDLE
LOCK BUTTON

For convenience when carrying or transporting your
miter saw from one place to another, a carrying
handle has been provided on top of the saw arm as
shown in figure 4. To transport, turn off and unplug
your saw, then lower the saw arm and lock it in the
down position. Lock saw arm by depressing the lock
pin.
CARRYING
HANDLE

SWITCH
TRIGGER
LOCK
PIN

SAW
ARM

Fig. 5
SPINDLE
LOCK
See Figure 5

BUTTON

A spindle lock button has been provided for locking
the spindle which stops the rotation of the blade in
your saw. Depress and hold the lock button while
installing, changing, or removing blade.

MITERLOCK
HANDLE
SAW ARM
LOCKED IN DOWN POSITION

POSITIVE

STOPS

ON MITER

SWITCH
TRIGGER
Fig. 4

TABLE

Positive stops have been provided at 0°, 22-1/2 ° and
45° . The 22-1/2 ° and 45 ° positive stops have been
provided on both the left and right side of the miter
table.
BEVEL

LOCK

KNOB
Fig. 6

The bevel lock knob securely locks your compound
miter saw at desired bevel angles. Positive stop
adjustment screws have been provided on each side
of the saw arm. These adjustment screws are for
making fine adjustments at 0° and 45 °. See pages 18
and 19.
LOCK-OFF

TRIGGER

LOCK

See Figure 6
To prevent unauthorized use of your compound miter
saw, we suggest that you disconnect it from the power
supply and lock the switch in the off position To lock
the switch, install a padlock through the hole in the
switch trigger A lock with a shackle up to 13/64 in
diameter may be used. When the lock is installed and
locked, the switch is inoperable. Store the padlock key
in another location.

LEVER

See Figure 5
The switch trigger is equipped with a lock-off lever to
reduce the possibility of accidental starting. The lockoff lever must be pressed down with the palm of your
hand to turn saw on. Once the saw is on, the lock-off
lever can be released. The spring loaded lever will
spring back into the lock-oft position when the switch
trigger is released.
11

MOUNTING

HOLES

1O_-

341/4"

See Figure 7.
Your compound miter saw should be permanently
mounted to a firm supporting surface such as workbench. Four 7/16 in. bolt holes have been provided in
the saw base for this purpose. Each of the tour
mounting holes should be bolted securely using
3/8 in. machine bolts, lock washers, and hex nuts (not
included). Bolts should be of sufficient length to
accommodate the saw base, lock washers, hex nuts,
and the thickness of the workbench.

-9I"

Tighten all four bolts securely.

The hole pattern for an 18 in. x 24 in. workbench is
shown in Figure 7. Carefully check the workbench
after mounting to make sure that no movement can
occur during use. If any tipping, sliding, or walking is
noted, secure the workbench to the floor before
operating.

Fig. 7
The operation of any saw can
,& WARNING:
result in foreign objects being thrown into your

_IL WARNING: Always make sure your compound
miter saw is securely mounted to a workbench or
an approved workstand. Failure to do so could
result in an accident resulting in possible serious
personal injury.

ELECTRICAL

eyes, which can result in severe eye damage.
Before starting power tool operation, always
wear safety goggles or safety glasses with side
shields and a full face shield when needed. We
recommend wide vision safety mask for use over
eyeglasses or standard safety glasses with side
shields.

CONNECTION

Your saw has a precision built electric motor. It should
be connected to a power supply that is 120 volts,
60 Hz, AC only (normal household current). Do not
operate this tool on direct current (DC). A substantial
voltage drop will cause a loss of power and the motor
will overheat. If your tool does not operate when
plugged into an outlet, double-check the power
supply.

WARNING: Do not attempt to modify this tool or
create accessories not recommended for use
with this tool. Any such alteration or modification
is misuse and could result in a hazardous
condition leading to possible serious personal
injury.

MITER

WARNING: To prevent accidental starting that
could cause possible serious personal injury,
assemble all parts to your saw before connecting
it to power supply. Saw should never be
connected to power supply when you are
assembling parts, making adjustments, installing
or removing blades, or when not in use.

LOCK HANDLE

See _gure 8.
To install the miter lock handle, place the threaded
stud on the end of the miter lock handle into the
threaded hole in the control arm. Turn clockwise to
tighten.

As mentioned previously your saw has been factory
assembled and adjusted. The miter lock handle, dust
guide, and blade are the only parts that have to be
installed.

TO INSTALL

BLADE

See Figures 10, 11, and 12.

LOOSEN

TIGHTEN
CONTROL
ARM
MITER
LOCKHANDLE
DUST

•
MITER
TABLE

WARNING: A 10 in. blade is the maximum
blade capacity of your saw. Never use a blade
that is too thick to allow outer blade washer to
engage with the flats on the spindle. Larger
blades will come in contact with the blade
guards, while thicker blades will prevent the
blade screw from securing the blade on the
spindle. Either of these situations could result in
a serious accident and can cause serious
personal injury.
Unplug your saw.

_1, WARNING: Failure to unplug your saw could
result in accidental starting causing possible
serious personal injury.

Fig. 8

GUIDE

See Figure 9.

Push down on the saw arm and pull out the lock
pin to release saw arm. Raise saw arm to its full
raised position. Be cautious, saw arm is spring
loaded to raise.

To install the dust guide, place the end marked
INSERT over the exhaust port in the upper blade
guard. Turn the guide so that the open end is facing
down or toward the rear of the saw.

Loosen the phillips screw on the blade bolt
cover until blade bolt cover can be raised.
See Figure 10 and 11.

EXHAUST
PORT
DUSTGUIDE

Gently raise the lower blade guard bracket,
releasing lower blade guard from notch so that
lower blade guard and blade bolt cover can be
rotated up and back to expose the blade bolt. See
Figures lO and 11.

DUSTBAG

PHILLIPSSCREW

LOWER
BLADEGUARD

Fig. 9
DUST

BAG

See Figure

The dust bag fits over the exhaust port on the upper
blade guard. To install the dust bag, remove the dust
guide from the exhaust port. Then, squeeze the two
metal clips to open the mouth of the bag and slide the
bag on the exhaust port. Release the clips. The metal
ring in the bag should lock in between the grooves on
the exhaust port. For more efficient operation, empty
the dust bag when no more than half full. This will
permit better air flow through the bag.

LOWERBLADE
GUARDBRACKET
Fig. 10
13

LOWER
BLADEGUARD

PHILLIPS
SCREW

•

B
BOLTCOVER

•
FLAT(S)
ONSPINDLE

INNERBLADE
DOUBLE"D"FLATS
TO
LOOSEN

TIGHTEN
BLADEBOLT

BLADE

•

Depress the spindle lock button and rotate the
blade bolt until the spindle locks. See Figure 12.

•

Using the btade wrench provided, _oosen and
remove the blade bolt.

Fit saw blade inside lower blade guard and onto
spindle. The blade teeth point downward at the
front of saw as shown in figure 11.
CAUTION: Always install the blade with the
blade teeth and the arrow printed on the side of
the blade pointing down at the front of the saw.
The direction of b_ade rotation is a_so stamped
with an arrow on the upper blade guard.
Replace outer blade washer. The double "D" flats
on the blade washers align with the flats on the
spindle.

•

Depress spindle lock button and replace blade
bott.
Note: The blade belt has left hand threads. Turn
blade belt counterclockwise to tighten.

Note: The blade bolt has left hand threads. Turn
blade bolt clockwise to loosen.
•

WARNING: If inner blade washer has been
removed, replace it before placing blade on
spindle. Failure to do so could cause an accident
since blade will not tighten properly.

•
OUTER BLADE WASHER
WITH DOUBLE "D" FLATS
Fig. 11

Wipe a drop of oil onto inner blade washer and
outer blade washer where they contact the blade,

Remove outer blade washer. Do not remove
inner blade washer.

SPINDLE
LOCK'_
BUTTON

•
•

Tighten b_ade bott securely.
Remove the blade wrench and store it in a safe
place for future use.

•

Replace the lower blade guard and blade bolt
cover.

•

Retighten phillips screw securing blade bolt cover.
Tighten screw securely, See Figure 11.

WARNING: Make sure the spindle lock button is
not engaged before reconnecting saw into power
source. Never engage spindle lock button when
blade is rotating,

Your compound miter saw has been adjusted at the
factory for making very accurate cuts. However, some
of the components might have been jarred out of
alignment during shipping. Also, over a period of time,
readjustment will probably become necessary due to
wear. After unpacking your saw, check the following
adjustments before you begin using saw. Make any
readjustments that are necessary and periodically
check the parts a_ignment to make sure that your saw
is cutting accurately.
_,
Fig. 12

WARNING: Your saw should never be
connected to power supply when you are
assembling parts, making adjustments, installing
or removing blades, or when not in use.
DisconnectLng your saw will prevent accidental
starting that could cause serious injury.

Note:Manyoftheillustrations
inthismanual
show
onlyportionsofyourcompound
mitersaw.Thisis
intentional
sothatwecanclearryshowpointsbeing
madeintheillustrations.
Neveroperateyoursaw
withoutallguardssecurelyinplaceandingood
operating
condition.

FRAMING
SQUARE

MITERTABLE

CUTTING
A SLOT IN THE ZERO
CLEARANCE
THROAT
PLATE
In order to use your compound miter saw, you must
cut a slot through the zero clearance throat plate to
allow for blade clearance. To cut the slot, set your
saw at O degrees miter, turn saw on and allow the
blade to reach full speed, then carefully make a
straight cut as far as it will go through the throat plate.
Turn your saw off and allow the blade to come to a
complete stop before raising the saw arm.

MITER
LOCK PLATE

MITER
LOCK HANDLE
VIEW OF MITER TABLE SQUARE WITH FENCE
AND CORRECTLY ADJUSTED
Fig. 13

Next, adjust the bevel angle to 45 degrees, turn your
saw on and allow the blade to reach full speed, then
carefully make another cut through the zero clearance
throat plate. The throat plate will then be wide enough
to allow the blade to pass through it at any angle from
0 to 45 degrees.
SQUARING
THE
TO THE FENCE

MITER

THROAT PLATE

FENCE

//!

_]MIT_/R

TABLE

See Figures 13 - 16.
•
_l,

Unplug your saw.
WARNING: Failure to unplug your saw could
result in accidental starting causing possible
serious personal injury.

•

Push down on the saw arm and pull out the lock
pin to release the saw arm.

•

Raise saw arm to its furl raised position.

•

Loosen the miter lock handle approximately
half turn.

•

VIEW OF MITER TABLE NOT SQUARE WITH
FENCE, ADJUSTMENTS ARE REQUIRED

one-

Fig. 14

Depress the miter lock plate and rotate the miter
table until the pointer on the control arm is positioned at 0°.

•

Release the miter lock plate and securely
the miter lock handle.

•

Lay a framing square flat on the miter table. Place
one leg of the square against the fence. Place the
other leg of the square beside the zero clearance
throat plate in the miter table. The edge of the
square and the zero clearance throat plate in
the miter table should be parallel as shown in
figure 13.

•

If the edge of the framing square and the zero
clearance throat plate in the miter table are not
parallel as shown in figures 14 and 15, adjustments are needed.

FENCE
MITER TABLE

tighten

FRAMING
SQUARE

ZERO CLEARANCE
THROAT PLATE

VIEWOFMITERTABLENOTSQUAREWITH
FENCE,ADJUSTMENTS
AREREQUIRED
Fig. 15
15

•

Using an 6 mm key, loosen the socket head
screws securing the fence. See Figure 16, Adjust
the fence left or right until the framing square and
zero clearance throat plate are parallel.

•

Retighten the screws securely and recheck the
fence-to-table alignment.
6 mmSOCKETHEAD
SCREW(S)

FENCE

6 mmSOCKETHEAD
SCREW(S)

LOCK PLATE

MITER
TABLE

FRAMING
SQUARE
MITER
LOCKHANDLE

VIEW OF BLADE
SQUARE WITH FENCE

Fig. 17

FENCE
Fig. 16
SQUARING
FENCE

THE

SAW

BLADE

TO THE

See Figures 17- 20.
•

Unplug your saw,
BLADE

WARNING: Failure to unplug your saw could
result in accidental starting causing possible
serious personal injury.
MITER FRAMING
TABLE SQUARE

Pull the saw arm all the way down and engage
the lock pin to hold the saw arm in transport
position.

VIEWOF BLADENOTSQUAREWITH
FENCE,ADJUSTMENTS
AREREQUIRED

Loosen the miter lock handle approximately
one-half turn.

Fig. 18

Depress the miter lock plato and rotate the miter
table until the pointer on the control arm is
positioned at 0 °.
Release the miter lock plate and securely tighten
the miter lock handle.
Lay a framing square flat on the miter table. Place
one leg ofthe square against the fence. S_{dethe
other leg of the square against the flat part of saw
blade.

BLADE

Note: Make sure that the square contacts the flat
part of the saw blade, not the blade teeth.
MITER
TABLE

FRAMING
SQUARE

VIEW OF BLADE NOT SQUARE WITH
FENCE, ADJUSTMENTS ARE REQUIRED
Fig. 19

•
•
•

Theedgeofthesquareandthesawbladeshould
beparallelasshowninfigure17.
If thefrontor backedgeofthesawbladeangles
awayfromthesquareasshowninfigures18and
19,adjustments
areneeded.
Usingthe8 mmhexkeyprovided,
loosenthe
socketheadscrewsthatsecurethemounting
brackettothemitertable.See Figure 20.

•

Loosen bevel lock knob and set saw arm at 0°
bevel (blade set 90° to miter table). Tighten bevel
lock knob.

•

Place a combination square against the miter
table and the flat part of saw blade.
Note; Make sure that the square contacts the flat
part of the saw blade, not the blade teeth.

•

Rotate the blade by hand and check the blade-totable alignment at several points.

•

The edge of the square and the saw blade should
be parallel as shown in figure 21.

FENCE

8 mm SOCKET
HEAD€

MITER

8 mmHEXKEY
WRENCH

MITER
TABLE

MOUNTING
BRACKET

Rotate the mounting bracket left or right until the
saw blade is parallel with the square.

•

Retighten the screws securely and recheck the
blade-to-fence alignment.

BLADE

COMBINATION
SQUARE

MITER
LOCKHANDLE
CORRECTVIEWOF BLADE
SQUAREWITHMITERTABLE
Fig. 21

Fig. 20

•

SQUARING
THE
MITER TABLE

MITER
TABLE

•

TO THE

If the top or bottom of the saw blade angles away
from the square as shown in figures 22 and 23,
adjustments are needed.

FENCE

See Figures 21-24.
•
_,

Unplug your saw.
WARNING: Failure to unplug your saw could
result in accidental starting causing possible
serious personal injury.
Pull the saw arm all the way down and engage
the lock pin to hold the saw arm in transport
position.
Loosen the miter lock handle approximately onehalf turn.

!R
TABLE

Depress the miter lock plate and rotate the miter
table until the pointer on the control arm is positioned at 0°.

COMBINATION
SQUARE

VIEWOFBLADENOTSQUAREWITHMITER
TABLE,ADJUSTMENTS
AREREQUIRED
Fig. 22

Release the miter lock plate and securely tighten
the miter lock handle.

FENCE

PIVOT

ADJUSTMENTS

Note: These adjustments were made at the factory
and normally do not require readjustment.
TRAVEL
•

MITER
TABLE

PIVOT

ADJUSTMENT

The saw arm should rise completely to the up
position by itself.
If the saw arm does not raise by itself or if there is
play in the pivot joints, have saw repaired by a
qualified service technician at your nearest Sears
store to avoid risk of personal injury.

COMBINATION
SQUARE

BEVEL
•

VIEW OF BLADE NOT SQUARE WITH MITER
TABLE, ADJUSTMENTS ARE REQUIRED
Fig. 23

•

Using a 10 mm wrench or adiustable wrench,
loosen the lock nut securing positive stop adjustment screw. Also loosen bevel lock knob.

•

Adjust positive stop adjustment screw to bring
saw blade into alignment with the square. See
Figure 24.

PIVOT

ADJUSTMENT

Your compound miter saw should bevel easily by
loosening the bevel lock knob and tilting the saw
arm to the left.
If movement is tight or if there is play in the pivot,
have saw repaired by a qualified service technician at your nearest Sears store to avoid risk of
personal injury.

DEPTH

STOP

The depth stop limits the blade's downward travel, It
allows the blade to go below the miter table enough to
maintain full cutting capacities. The depth stop positions the blade 1/4 in. from the miter table support.
Note: The miter table support is located inside miter
table.
The depth stop is factory set to provide maximum
cutting capacity for the 10 in. saw blade provided with
your saw. Therefore, the saw blade provided should
never need adjustments.
However, when the diameter of the blade has been
reduced due to sharpening, it may be necessary to
adjust the depth stop to provide maximum cutting
capacity. Also, when a new blade is installed, it is
necessary to check the clearance of the blade to the
miter table support before starting the saw. Make
adjustments if needed.

POSITIVESTOP
ADJUSTMENT
SCREWFOR
45°ANGLES

DEPTH

STOP

ADJUSTMENTS

See Figure 25.

NUT(S)

•

Unplug your saw.

Fig. 24
_i,

•

Retighten bevel lock knob. Next, retighten lock nut
securing the positive stop adjustment screw.
Recheck blade-to-table alignment.

WARNING:
Failure to unplug your saw could
result in accidental starting causing possible
serious personal injury.

To adjust the depth stop use a 17 mm wrench or
adjustable wrench and loosen the hex nut at the
rear of the miter saw arm.

Note: The above procedure can be used to check
blade squareness of the saw blade to the miter
table at both 0 ° and 45 ° angles.

Use the 5 mm hex key wrench provided to adjust
the depth stop adjustment screw. The saw blade
is lowered by turning the screw counter-clockwise
and raised by turning the screw clockwise.

Your saw has three scale indicators, two on either
side of the bevel scale and one on the miter scale.
After squaring adjustments have been made, it may
be necessary to loosen the indicators screws and
reset them to zero.

DEPTH STOP
ADJUSTMENT
SCREW

_1, WARNING: Before starting any cutting
operation, clamp or bolt your compound miter
saw to a workbench. Never operate your miter
saw on the floor or in a crouched position.
Failure to heed this warning can result in serious
personal injury.

L._

BEVEL
LOCKKNOB

CUTTING
WITH
MITER SAW
MITER
TABLE

POSITIVE LOCKNUT(S)
STOPADJUSTMENT
SCREWFOR0° ANGLES

Lower the blade into the zero clearance throat
plate of the miter table. Check blade clearance
and maximum cutting distance (distance from
fence where blade enters) to front of miter table
slot.

•

Readjust if necessary.

CROSSCUTTING
See Figure 26.
A crosscut is made by cutting across the grain of the
workpiece. A straight crosscut is made with the miter
table set at the zero degree position. Miter crosscuts
are made with the miter table set at some angle other
than zero.

TO CROSSCUT
SAW:

_1= WARNING: Do not start your compound miter
saw without checking for interference between
the blade and the miter table support. Damage
could result to the blade if it strikes the miter
table support during operation of the saw.
•
•

•
•

Tighten the hex nut with a 17 mm wrench or
adjustable wrench.
To prevent the depth stop adjustment screw from
turning while tightening the hex nut, carefully hold
it with the hex key wrench while tightening the
hex nut.

•

Cross cutting miters, joints, etc. for picture frames,
moldings, door casings, and fine joinery.

YOUR

MITER

Pull out the lock pin and lift saw arm to its full
height.
Loosen the miter lock handle. Rotate the miter
lock handle approximately one-half turn to the left
to loosen.
Press the miter lock plate down with your thumb
and hold.

•

Rotate the control arm until the pointer aligns with
the desired angle on the miter scale.

•

Release the miter lock plate.
Note: You can quickly locate 0 °, 22-1/2 ° left or
right, and 45 ° left or right by releasing the lock
plate as you rotate the control arm. The lock plate
will seat itself in one of the positive stop notches,
located in the miter table frame.

(Use only for the purposes listed below)
Cross cutting wood and plastic.

WITH

•

APPLICATIONS
•

COMPOUND

WARNING: When using a work clamp or
C-clamp to secure your workpiece, clamp
workpiece on one side of the blade only. The
workpiece must remain free on one side of the
blade to prevent the blade from binding in
workpiece. The workpiece binding the blade will
cause motor stalling and kickback. This situation
could cause an accident resulting in possible
serious personal injury.

Fig. 25

•

YOUR

•

Note: The 104 tooth crosscut blade provided is fine
for most wood cutting operations, but for fine joinery
cuts or cutting plastic, use one of the accessory
blades available from your nearest Sears store.

Tighten the miter lock handle securely.
WARNING:
To avoid serious personal injury,
always tighten the miter lock handle securely
before making a cut, Failure to do so could result
in movement of the control arm or miter table
while making a cut.

Slowly lower the blade into and through the
workpiece. See Figure 26.
Release the switch trigger and allow the saw
blade to stop rotating before raising the blade out
of workpiece. Wait until the electric brake stops
blade from turning before removing the workpiece
from the miter table.

STRAIGHT
CROSSCUT

BEVEL

CUT

See Figures 27 and 28.
A bevel cut is made by cutting across the grain of the
workpiece with the blade angled to the workpiece. A
straight bevel cut is made with the miter table set at
the zero degree position and the blade set at an angle
between 0° and 45°.
LEFTSIDE
LEFT
INDICATOR
POINT

• C-CLAMP
•

•

RIGHTSIDE
RIGHT
INDICATOR
POINT

Fig. 26

Place the workpiece flat on the miter table with
one edge securely against the fence. If the board
is warped, place the convex side against the
fence. If the concave edge of a board is placed
against the fence, the board could collapse on the
blade at the end of the cut, jamming the blade.
See Figures 33 and 34.

SCALE
MOUNTINGBRACKET

TO BEVEL
SAW:

When cutting long pieces of lumber or molding,
support the opposite end of the stock with a roller
stand or with a work surface level with the saw
table.

•

Align cutting line on the workpiece with the edge
of saw blade.

•

Grasp the saw handle firmly, press the lock-off tab
down, then squeeze the switch trigger. Allow
several seconds for the blade to reach maximum
speed.

YOUR

MITER

Pull out the lock pin and lift saw arm to its full
height.

Press the miter lock plate down with your thumb
and hold.
Rotate the control arm until the pointer aligns with
zero on the miter scale.

WARNING: To avoid serious personal injury,
keep your hands outside the no hands zone; at
least 3 in. from blade. Never perform any cutting
operation freehand (without holding workpiece
against the fence). The blade could grab the
workpiece if it slips or twists.
Before turning on the saw, perform a dry run of the
cutting operation just to make sure that no
problems will occur when the cut is made.

CUT WITH

Fig. 27

Loosen the miter lock handle. Rotate the miter
lock handle approximately one-half turn to the left
to loosen.

Grasp the stock firmly with one hand and secure
it against the fence. Use the optional work clamp
or a C-clamp to secure the workpiece when
possible. See Figure 26.

•

SCALE

Release the miter lock plate.
Note: You can quickly locate zero by releasing
the lock plate as you rotate the control arm. The
lock plate will seat itself in one of the built-in
positive stop notches, located in the miter table
frame.
•

Tighten the miter lock handle securely.
WARNING:
To avoid serious personal injury,
always tighten the miter lock handle securely
before making a cut. Failure to do so could result
in movement of the control arm or miter table
while making a cut.

,_,

WARNING:

To avoid serious personal

injury,

keep your hands outside the no hands zone; at
least 3 in. from blade. Never perform any cutting
operation freehand (without holding workpiece
against the fence). The blade could grab the
workpiece if it slips or twists.

BEVELCUT

•

Before turning on the saw, perform a dry run of
the cutting operation just to make sure that no
problems will occur when the cut is made.

•

Grasp the saw handle firmly, press the lock-off tab
down, then squeeze the switch trigger. Allow
several seconds for the blade to reach maximum
speed.

•

Slowly lower the blade into and through the
workpiece. See Figure 28.
Release the switch trigger and allow the saw
blade to stop rotating before raising the blade out
of workpiece. Wait until the electric brake stops
blade from turning before removing the workpiece
from miter table.

COMPOUND
:LAMP

Loosen the bevel lock knob and move the saw
arm to the left to the desired bevel angle.

•

Bevel angles can be set from 0° to 45 °,

•

For your convenience there is a double scale
located on the mounting bracket. See Figure 27. If
one side becomes difficult to read as you move
the saw arm to the left, simply refer to the other
side. A,
the indicator point for the side you
choose with the '=.siredangle.
Once the saw arm has been set at the desired
angle, securely tighten the bevel lock knob.

•
•

To make this type of cut the control arm on the miter
table must be rotated to the correct angle and the saw
arm must be tilted to the correct bevel angle. Care
should always be taken when making compound miter
setups due to the interaction of the two angle settings.
Adjustments of miter and bevel settings are interdependent with one another. Each time you adjust the
miter setting you change the effect of the bevel
Setting. Also, each time you adjust the bevel setting
you change the effect of the miter setting.

It may take several settings to obtain the desired cut.
The first angle setting should be checked after setting
the second angle, since adjusting the second angle
affects the first.
Once the two correct settings for a particular cut have
been obtained, always make a test cut in scrap
material before making a finish cut in good material.

When cutting long pieces of lumber or molding,
support the opposite end of the stock with a roller
stand or with a work surface level with the saw
table.
Align the cutting line on the workpiece
edge of saw blade.

CUT

A compound miter cut is a cut made using a miter
angle and a bevel angle at the same time. This type of
cut is used to make picture frames, cut molding, make
boxes with sloping sides, and for certain roof framing
cuts.

Fig. 28

•

MITER

with the

Grasp the stock firmly with one hand and secure it
against the fence. Use the optional work clamp or
a C-clamp to secure the workpiece when possible. See Figure 28.

TO MAKE

A COMPOUND

CUT WITH

YOUR
MITER
SAW:
•
Pull out the lock pin and lift saw arm to its full
height.
•

Loosen the miter lock handle. Rotate the miter lock
handle approximately one-half turn to the left to
loosen.

•

Press the miter lock plate down with your thumb
and hold.

•

Recheck miter angle setting. Make a test cut in
scrap material.

•

Place the workpiece flat on the miter table with
one edge securely against the fence. If the board
is warped, place the convex side against the
fence. If the concave edge of a board could
collapse on the blade at the end of the cut,
jamming the blade. See Figures 33 and 34.

•

When cutting long pieces of lumber or molding,
support the opposite end of the stock with a roller
stand or with a work surface level with the saw
table.

•

Align the cutting line on the workpiece with the
edge of saw blade.

Rotate the control arm until the pointer aligns with
the desired angle on the miter scale.
Release the miter lock plate.
Note: You can quickly locate 0 °, 22-1/2" left or
right, and 45" left or right by releasing the miter
lock plate as you rotate the control arm. The miter
lock plate will seat itself in one of the positive stop
notches, located in miter table frame.
•
_i,

Tighten the miter lock handle securely.

WARNING: To avoid serious personal injury,
always t!ghten the miter lock handle securely
before making a cut. Failure to do so could result
in movement of the control arm or miter table
while making a cut.

•

Loosen the bevel lock knob and move the saw arm
to the left to the desired bevel angle.

•

Bevel angles can be set from 0" to 45".

•

For your convenience there is a double scale
located on the mounting bracket. See Figure 27. If
one side becomes difficult to read as you move the
saw arm to the left, simply refer to the other side.
Align the indicator point for the side you choose
with the desired angle.
Once the saw arm has been set at the desired
angle, securely tighten the bevel lock knob.

•

Grasp the stock firmly with one hand and secure it
against the fence. Use the optional work clamp or
a C-clamp to secure the workpiece when possible.
See Figure 29.
WARNING: To avoid serious personal injury,
always keep your hands outside the no hands
zone; at least 3 in. from blade. Never perform any
cutting operation freehand (without holding
workpiece against the fence). The blade could
grab the workpiece if it slips or twists.

COMPOUND
MITERCUT

C-CLAMP

Fig. 29

•

•
•

Before turning on the saw, perform a dry run of the
cutting operation just to make sure that no problems
will occur when the cut is made.
Grasp the saw handle firmly, press the lock-off tab
down, then squeeze the switch trigger. Allow several seconds for the blade to reach maximum speed.
Slowly lower the blade into and through the
workpiece. See Figures 29 and 30.
Release the switch trigger and allow the saw blade
to stop rotating before raising the blade out of
workpiece. Wait until the electric brake stops blade
from turning before removing the workpiece from
miter table.

SUPPORT

LONG

WORKPIECES

See Figure 31.
Long workpieces need extra supports. Supports
should be placed along the workpiece so it does not
sag. The support should let the workpiece lay flat on
the base of the sew and work table during the cutting
operation. Use the optional work clamp or a C-clamp
to secure the workpiece.
_1,

45° X 45° COMPOUNDMITERCUT

WARNING: To avoid serious personal injury,
always keep your hands outside the no hands
zone; at least 3 in. from blade. Never perform
any cutting operation freehand (without holding
workpiece against the fence). The blade could
grab the workpiece if it slips or twists.

Fig. 30

LONGWORKPIECE

WORKPIECESUPPORTS

Fig. 31

CUTTING

COMPOUND

MITERS

To aid in making the correct settings, the compound angle setting chart below has been provided. Since compound cuts are the most difficult to accurately obtain, trial cuts should be made in scrap material, and much
thought and planning made, prior to making your required cut.
NUMBER OF SLOES

PITCH

OFSIOE
0o

M-45.00 ° M-36.00 °
B0.00 ° B0.00 °

10
i

M-30.00 °
B- 0.00 °

M-25.71 °
B0.00 °

M-22.50 °
B- 0.00 °

M-20.00 °
B0.00 °

M- 18.00 °
B- 0.00 °

5°

IM-44.89 °
B3.53 °

M-35.90 °
B- 2.94 °

M-29,91 °
B- 2.50 °

M-25.63 °
B- 2.17 °

M-22,42 °
B- 1,91 °

M-19.93 °
B- 1.71 °

M-17.94 °
B- 1.54 °

10°

M-44.56 °
B- 7.05 °

M- 35.58 °
B- 5,86 °

M-29.62 °
B- 4.98 °

M-25.37 °
B- 4.32 °

M-22.19 °
B- 3.81 °

M- 19.72 °
B- 3.40 °

M- 17.74 °
B- 3.08 °

15 °

M- 44.01 °
B-10.55 °

M- 35.06 °
B- 6.75 °

M- 29.15 °
B- 7,44 °

M- 24,95 °
B- 6.45 °

M- 21.81 °
B- 5.68 °

M- 19.37 °
B- 5.08 °

M- 17.42 °
B- 4,59 °

20 °

M- 43.22 °
B-14.00 °

M- 34.32 °
B-11.60 °

M- 28.48 °
B- 9.85 °

M- 24.35 °
B- 8,53 °

M- 21.27 °
B- 7,52 °

M- 18.88 °
B- 6.72 °

M- 16.98 °
8- 6.07 °

25 °

M-42.19 °
8- 17,39 °

M-33.36 °
B- 14.38 °

M. 27.62 °
B- 12.20 °

M-23,56 °
B- 10.57 °

M-20.58 °
8- 9.31 °

M-18.26 °
B- 8.31 °

M-16.41 o
B- 7.50 °

30 °

M-40,89 °
B-20.70 °

M- 32.18 °
B- 17.09 °

M- 26.57 °
B- 14.48 °

M- 22,64 °
8- 12,53 °

M- 19.73 °
B- 11.03 °

M- 17.50 °
B- 9.85 °

M- 15,72 °
B- 8.89 °

35 °

M- 39,32 °
B- 23,93 °

M- 30.76 °
B- 19.70 °

M- 25.31 °
B- 16,67 °

M- 21.53 °
8o 14.41 °

M- 18,74 °
B- 12.68 °

M- 16.60 °
B- 11.31 °

M- 14.90 °
B- 10,21 °

M-37.45

M-29,10

M-23.86

M-20.25

M- 17.60 °

M- 15.58 °

M- 13.98 °

40°
45 °

50°
55 °
60 °

65°
70 °
75 °
80 °

85°
90 °

B- 27.03 °
M-35.26 °

B- 22.20 °
M-27,19 °

8- 18.75 °
M-22,21 °

B- 16.19 °
M-18.80 °

B- 14.24 ° I B- 12.70 ° I 8- 11.46 °
M-16.32 ° M-14.43 ° !M-12.94 °

B- 30,00 °
M- 32.73 °

B-24.56 °
M-25.030

8-20.70 °
M-20.36 °

B-17.87 °
M- 17,20 °

B-15.70 ° IB-14.00°
M- 14.91 ° M- 13.17 °

B-12.62 °
M- 11.80 °

B- 32.80 °
M- 29.84 °

B- 26.76 °
M- 22.62 °

B-22.52 °
M- 18.32 °

Bo 19.41 °
M- 15,44 °

B- 17.05 °
M- 13,36 °

B- 15.19 °
M- 11.79 °

B- 13,69 °
M- 10.56 °

B- 35.40 °

B- 28.78 °

B- 24.18 °

B÷ 20.82 °

M- 19.96 °
B- 30.60 °

M- 16.10 °
B- 25.66 °

M- 13.54 °
Bo 22.07 °

B- 18.27 ° I B- 16.27 °
I
M- 11,70 ° M- 10.31 °
B- 19.35 ° B- 17,23 °

B- 14.66 °

M- 26.57 °
B- 37,76 °
M-22.91 °
B- 39.86 °

M- 17.07 °
B- 32.19 °

M- 13.71 °
B- 26.95 °

M- 11.50 °
B÷ 23,16 °

M- 9.93 °
B- 20.29 °

M- 8.74 °
B- 18.06 °

M- 7.82 °
B -16.26 °

M-18.B8 °
B- 41.64 °

M-13.95 °
B- 33.53 °

M-11.17 °
B- 28.02 °

M- 9.35 °
B- 24.06 °

M- 8.06 °
B- 21.08 °

M- 7.10 °
B- 18.75 °

M- 6.34 °
B- 16.88 °

M-14.51 °
B- 43.08 °

M-10.65 °
B- 34.59 °

M- 8.50 °
B- 28.88 °

M- 7.10 °
B- 24.78 °

M- 6.12 °
B- 21.69 °

M- 5.38 °
B- 19,29 °

M- 4.81 °
B- 17,37 °

M- 9.85 °
B- 44.14 °

M- 7.19 °
B- 35.37 °

M- 5.73 °
B- 29.50 °

M- 4.78 °'
B- 25.30 °

M- 4.11 °
8- 22.14 °

M- 3.62 °
B- 19.68 °

M- 3,23 °
8- 17.72 °

M- 4,98 °
B- 44.78 °

M- 3.62 °
B- 35.84 °

M- 2.88° !M - 2.40 °
B- 29.87 °
B- 25.61 °

M-2.07 °
B- 22.4t°

M-1.82 °
B- 19,92 °

M- 1.62 °
B- 17.93 °

M- 0.00 °
B- 45.00 °

M- 0.00 °
B- 36.00 °

M- 0.00 °
B- 30,00 °

M- 0.00 °
B- 22.50 °

M- 0,00 °
8- 20.00 °

M- 0.00 °
B- 18.00 °

M- 0.00 °
Bo 25.71 °

Each B (Bevel) and M (Miter) Setting is Given to the Closest 0.005 °.
COMPOUND-ANGLE SETTINGS FOR POPULAR STRUCTURES

M- 9.23 °
B- 15.52 `=

CUTTING

CROWN

MOLDING

LAYING
MITER

Your compound miter saw does an excellent job of
cutting crown molding. In general, compound miter
saws do a better job of cutting crown molding than
any other tool made.

MOLDING
TABLE

FLAT

THE

See Figure 32.
To use this method for accurately cutting crown
molding for a 90 _ inside or outside corner, lay the
molding with its broad back surface flat on the miter
table and against the fence.

In order to fit properly, crown molding must be compound mitered with extreme accuracy.
The two contact surfaces on a piece of crown molding
that fit flat against the ceiling and the wall of a room
are at angles that, when added together, equal
exactly 90 °. Most crown molding has a top rear angle
(the section that fits flat against the ceiling) of 52 ° and
a bottom rear angle (the section that fits flat against
the wall) of 38° .

When setting the bevel and miter angles for compound miters, remember that the settings are interdependent; changing one angle changes the other angle
as well.
Keep in mind that the angles for crown moldings are
very precise and difficult to set. Since it is very easy
for these angles to shift, all settings should first be
tested on scrap molding. Also most walls do not have
angles of exactly 90 ° , therefore, you will need to fine

tune your settings.
52°

W
A
L
L

CEILING

INS_
CORNER

FENCE

AGAINSTFENCE=
• LEFTSIDE,INSIDECORNER
• RIGHTSIDE,OUTSIDECORNER

FENCE

OUTSIDE
CORNER
BOTTOMEDGEAGAINSTFENCE=
• RIGHTSIDE,INSIDECORNER
• LEFTSIDE,OUTSIDECORNER

MITERTABLE

CROWN MOLDING FLAT ON MITER TABLE

Fig. 32

Whencuttingcrownmolding
bythismethodthebevel
angleshouldbesetat33.85°. Themiterangleshould
besetat31.62
° eitherrightor left,depending
onthe
desiredcutfortheapplication.
Seethechartbelowfor
correctanglesettingsandcorrectpositioning
ofcrown
molding
onmitertable.
Thesettingsinthechartbelowcanbeusedforcutting
AllStandard
(U.S.)crownmolding
with52°and38°
angles.Thecrownmoldingis placedflatonthemiter
tableusingthecompound
featuresofyourmitersaw.
Bevel
Angle
Setting

33"85°

Type of Cut
Left side, inside corner
1. Top edge of molding against fence
2. Miter table set right 31,62 °
3. Save left end of cut

WRONG

When cutting warped material, always make sure it is
positioned on the miter table with the convex side
against the fence as shown in figure 33.

Right side, inside corner
1, Bottomedge of molding against fence
2. Miter table set left 31.62 °
3. Save left end of cut

If the warped material is positioned the wrong way as
shown in figure 34, it will pinch the blade near the
completion of the cut.

Left side, outside corner
1, Bottom edge of molding againstfence
2. Miter table set left 31.62 °

_lh

3. Save right end of cut

33"85°

Right side, outside corner
1. Top edge of molding against fence
2. Miter table set right 31.62 °
3, Save right end of cut

CUTTING
WARPED
See Figures 33 and 34.

Fig. 34

WARNING: To avoid a kickback and to avoid
serious personal injury, never position the
concave edge of bowed or warped material
against the fence.

CLAMPING
WIDE
See Figure 35.

WORKPIECES

MATERIAL

WIDE
BOARD

RIGHT

Fig. 35

Fig. 33

When cutting wide workpieces such as a 2 in. x 6 in.,
boards should be clamped with a C-clamp as shown in
figure 35.
26

EXTENSION

WARNING: When servicing, use only identical
Craftsman replacement parts. Use of any other
part may create a hazard or cause product
damage.

The use of any extension cord will cause some loss of
power. To keep the loss to a minimum and to prevent
tool overheating, use an extension cord that is heavy
enough to carry the current the tool will draw.

GENERAL

A wire gage size (A.W.G.) of at least 14 is recommended for an extension cord 25 feet or less in
length. When working outdoors, use an extension
cord that is suitable for outdoor use. The cord's jacket
will be marked WA.

Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged
by their use. Use clean cloths to remove dirt, carbon
dust, etc.
_I,

CORDS

WARNING: Do not at any time let brake fluids,
gasoline, petroleum-based products, penetrating
oils, etc. come in contact with plastic parts. They
contain chemicals that can damage, weaken or
destroy plastic.

It has been found that electric tools are subject to
accelerated wear and possible premature failure when
they are used on fiberglass boats, sports cars,
wallboard, spackling compounds, or plaster. The
chips and grindings from these materials are highly
abrasive to electric tool parts such as bearings,
brushes, commutators, etc. Consequently, it is not
recommended that this tool be used for extended
work on any fiberglass material, wallboard, spackling
compounds, or plaster. During any use on these
materials it is extremely important that the tool is
cleaned frequently by blowing with an air jet.

CAUTION: Keep extension cords away from the
cutting area and position the cord so that it will
not get caught on lumber, tools, etc., during
cutting operation.

WARNING: Check extension cords before each
use. If damaged, replace immediately. Never use
tool with a damaged cord since touching the
damaged area could cause electrical shock
resulting in serious injury.

Always wear safety goggles or
a, WARNING:
safety glasses with side shields during power
tool operation or when blowing dust. If operation
is dusty, also wear a dust mask.

LUBRICATION
All of the bearings in this tool are lubricated with a
sufficient amount of high grade lubricant for the life of
the unit under normal operating conditions. Therefore,
no further lubrication is required.

Your saw has externally accessible brush assemblies
that should be periodically checked for wear.

WARNING: To ensure safety and reliability, all
repairs -- with the exception of the externally
accessible brushes -- should be performed by a
qualified service technician at a Sears store to
avoid risk of personal injury.

BRUSH

Proceed as follows when replacement
•
Unplug your saw.

is required:

_WARNING:
Failure to unplug your saw could
result in accidental starting causing serious
injury.

REPLACEMENT

See Figure 36.

BRUSH

BRUSH
CAP
BRUSH
CAP
BRUSH
ASSEMBLY

Fig. 36

•

Remove brush cap with a screwdriver. Brush
assembly is spring loaded and will pop out when
you remove brush cap.

•

Remove brush assembly.

•

Check for wear. Replace both brushes when
either has less than 1/4 in. length of carbon
remaining. Do not replace one side without
replacing the other.

•

Reassemble using new brush assemblies. Make
sure curvature of brush matches curvature of
motor and that brush moves freely in brush tube.

•

Make sure brush cap is oriented correctly
(straight) and replace.

•

Tighten brush cap securely. Do not overtighten.

CRAFTSMAN

COMPOUND

MITER SAW - MODEL

NUMBER

315.243000

6
26

G3
O

Figure A

CRAFTSMAN

COMPOUND MITER SAW - MODEL

The model number will be found on a plate attached to the motor housing.
CRAFTSMAN
COMPOUND MITER SAW or when ordering repair parts.

NUMBER

315.243000

Always mention the model number in all correspondence

PARTS LIST FOR FIGURE
KEY
NO.

PART
NUMBER

DESCRIPTION

QUAN.

KEY
NO.

regarding

your

PART
NUMBER

DESCRIPTION

QUAN.

710308-045

Bolt (M8 x 45 Soc. Hd.) ..................................

976511-001

Spring Washer ................................................ 1

360308-142

Lock Washer

976578-001

Nylon Lock Nut ............................................... 1

977443-001

Fence ..............................................................

700306-025

Screw (Socket Hd. Cap) ................................. 2

976516-001

Zero Clearance

360306-121

Lock Washer ................................................... 2

160030-400

Screw ..............................................................

976501-001

Control Arm .................................................... 1

976514-001

Miter Table ......................................................

976505-001

Miter Lock Handle ........................................... 1

976598-001

Cover Plate .....................................................

976506-001

Pointer ............................................................ 1

976601-001

Screw (Pan Hd.) .............................................

976526-001

Flat Washer (M4) ............................................ 1

976610-001

Miter Table Frame

976527-001

Screw (M4 x 10) ............................................. 1

(Includes

976509-001

Miter Lock Plate .............................................. 1

(M8) ..........................................

Throat Plate ..........................

Key Nos. 10, 11, 12, & 13) .............. 1

976531-001

Rivet ..............................................................

976568-001

Blade Wrench ................................................. 1

976515-001

Miter Scale

976570-001

5 mm Hex Key ................................................ 1

977434-001

Hand Warning

976605-001

6 mm Hex Key ................................................ 1

977435-001

Line Label .....................................................

976569-001

8 mm Hex Key ................................................ 1

976513-001

Table Spindle .................................................

976512-001

Washer

................................................
Label .......................................

...........................................................

AVAILABLE AT YOUR NEAREST SEARS CATALOG ORDER OR RETAIL STORE
II

CRAFTSMAN

COMPOUND

MITER SAW - MODEL

NUMBER

315.243000

8
2

I
5

GO
PO

14
15
FigureB
i

CRAFTSMAN

COMPOUND

MITER SAW - MODEL

NUMBER

315.243000

I COMPOUND
The model number
MITERwillSAW
be found
or when
on aordering
plate attached
repair parts.
to the motor housing. Always mention the model number in all correspondence

PARTS LIST FOR FIGURE
KEY
NO.

co
(,o

PART
NUMBER

DESCRIPTION

QUAN.

976528-001

Torsion Spring ................................................

977441-001

Support Bracket ..............................................

976530-001

Lock Washer ...................................................

976529-001

Bolt .................................................................

976518-001

Hex Bolt ..........................................................

976519-001

Hex Nut ...........................................................

976531-001

Rivet ...............................................................

976535-001

Bevel Scale .....................................................

700310-025

Bolt (M10 x 25 Hex Hd.) .................................

KEY
NO.

regarding your I

PART
NUMBER

976609-001

DESCRIPTION

QUAN.

976527-001

Bevel Pivot Bracket Assembly
(Includes Key Nos. 7 & 8) ...............................
Screw ..............................................................

1
2

976526-001

Washer

976525-001

Bevel Index Pointer

976520-001

Washer

...........................................................

976521-001

Pivot Shaft ......................................................

976512-001

Washer (MIO) .................................................

976522-001

Bevel Lock Knob .............................................

...........................................................
........................................

CRAFTSMAN

COMPOUND

MITER SAW - MODEL

NUMBER

315.243000

•

3
4

11
13
14

15
19
20
17

21
18

22
23

FigureC

CRAFTSMAN

COMPOUND MITER SAW - MODEL NUMBER 315.243000

The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence
COMPOUND
MITER SAW or when ordering repair parts.

PARTS LIST FOR FIGURE
KEY
NO.

co
ol

PART
NUMBER

DESCRIPTION

QUAN.

KEY
NO.

regarding

your [

PART
NUMBER

QUAN.

DESCRIPTION

976539-001

Dust Shield .....................................................

130030-401

Screw (M4 x 15) .............................................

976596-001

U-Clip ..............................................................

976547-001

Blade Washer

.................................................

976567-001

Dust Guide ......................................................

***

Saw Blade ......................................................

976543-001

Upper Blade Guard .........................................

976548-001

Blade Bolt (M8 x 20) .......................................

979687-001

Logo Plate ......................................................

976554-001

Return Spring .................................................

976599-001

Screw (M5 x 12) .............................................

976607-001

Lower Blade Guard Assembly

976733-001

Lower Blade Guard Label ...............................

976608-001

Blade Guard Bracket Assembry

976540-001

Caution

Label .................................................

976604-001

Phillips Screw .................................................

976600-001

Fixed Screw ....................................................

976552-001

Blade Bolt Cover .............................................

976549-001

Lock Nut ..............................

976541-001

Stopper ...........................................................

COMPLETE

ASSORTMENT

"...........................

AVAILABLE

AT YOUR NEAREST

(Includes

........................

Key No. 23) .....................................

976507-001

Washer

(M5) ...................................................

130030-501

Screw (M5 x 10) .............................................

976740-001

Label ...............................................................

976564-001

Screw ..............................................................

Item No._23466

Dust Bag .........................................................

SEARS CATALOG

ORDER

OR RETAIL

STORE

CRAFTSMAN

COMPOUND

MITER SAW - MODEL

NUMBER

315.243000

SEE NOTE "A"

-18
20

21
22

23
24

Figure D

CRAFTSMAN

COMPOUND

MITER

SAW - MODEL

I CRAFTSMAN
The model number
COMPOUND
will be found
MITER
on aSAW
plate or
attached
when ordering
to the motor
repair housing.
parts.

PART
NUMBER

DESCRIPTION

QUAN.

315.243000

Always mention the model number in all correspondence

PARTS LIST FOR FIGURE
KEY
NO.

NUMBER

KEY
NO.

regarding

your

PART
NUMBER

DESCRIPTION

QUAN.

976641-001

"O" Ring ..........................................................

981494-001

Data Plate .......................................................

976576-001

Lock Pin ..........................................................

976650-001

Spindle

976643-001

E-Ring .............................................................

976651-001

E-Ring .............................................................

976644-001

Screw (M4 x 16) .............................................

976649-001

Compression

976645-001

Rubber Bumper ..............................................

976647-001

Ball Bearing (6000zz)

976536-001

Flat Washer

976648-001

External

976537-001

Hex Nut (M12) ................................................

588028-108

Gear ................................................................

180031-002

Depth Stop Adjustment

Screw (M10 x 20) ..... 1

976853-001

Lock Ring ........................................................

300030-100

Hex Nut (M10) ................................................

976654-001

Square Key (4 x 4 x 28) ..................................

976664-001

Screw ........................................................

588030-008

Gear Shaft ......................................................

976663-001

Carrying

Handle .............................................

976658-001

Ball Bearing

976691-001

Warning

Label ..............................................

588031-004

Screw (Special)

976683-001

Brush Assembly

972000-710

Owner's Manual

976682-001

Brush Cap .............................................

(M12) ..........................................

.........................................

Lock Pin .............................................

Spring .......................................

Retaining

.....................................

Ring ..................................

(6004zz)

.....................................

..............................................

NOTE: "A"-THE ASSEMBLY SHOWN REPRESENTS AN IMPORTANT PART OF THE DOUBLE INSULATED SYSTEM. TO AVOID THE POSSIBILITY
OF ALTERATION OR DAMAGE TO THE SYSTEM, SERVICE SHOULD BE PERFORMED BY YOUR NEAREST SEARS REPAIR
CENTER. CONTACT YOUR NEAREST SEARS CATALOG ORDER OR RETAIL STORE FOR SERVICE CENTER INFORMATION.

For in-home major brand repair service:
Call 24 hours a day, 7 days a week

1-800-4-MY-Horne s,, (1-800-469-4663)
Para pedir servicio

de reparaci6n

a domicilio

- 1-800-676-5811

In Canada for all your service and parts needs call - 1-800-665-4455
Au Canada pour tout le service ou les pieces

For the repair or replacement

parts you need:

Call 7 am - 7 pm, 7 days a week
1-800-366-PART

(1-800-366-7278)

Para ordenar piezas con entrega a domicilio - 1o800-659-7084

For the location of a Sears Parts and Repair Center in your area:
Call 24 hours a day, 7 days a week

1-800-488-1222
For information on purchasing a Sears Maintenance Agreement
or to inquire about an existing Agreement:
Call 9 am - 5 pm, Monday

- Saturday

1-800-827-6655

The Service

Side of Sears sM

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : No
Page Count                      : 38
Page Layout                     : SinglePage
Page Mode                       : UseNone
Producer                        : Goby Monitor Application version 3, 2, 1, 4
Create Date                     : Tue Aug 14 09:52:44 2007
Author                          : 
Title                           : 
Subject                         :

EXIF Metadata provided by EXIF.tools

Craftsman 315243000 User Manual 10 COMPOUND MITER SAW Manuals And Guides L0050127

CRAFTSMAN Miter Saw Manual L0050127 CRAFTSMAN Miter Saw Owner's Manual, CRAFTSMAN Miter Saw installation guides

DURA-GLAS IITM P4RAG6C-150 L0050127

Navigation menu

Versions of this User Manual:

Views

Navigation